Transpak TP-201, TP-202, TP-202CE, TP-201CE, TP-203CE Operation Manual & Spare Parts List

READ ALL INSTRUCTIONS BEFORE OPERATING THIS PRODUCT

SEMI AUTOMATIC POL YPROPYLENE

STRAPPING MACHINE

TP-201 TP-202 TP-203 TP-202L

TP-201CE TP-202CE TP-203CE TP-202LCE

TP-201Y TP-201YS

OPERATION MANUAL

&

SPARE PARTS LIST

Original Instruction

PART I

CONTENTS

1. Safety Instructions................................................................................. 1

2. Construction and Units.......................................................................... 2

3. General Safety Remarks........................................................................ 3

4. Machine Information............................................................................. 5

5. Machine and Operating Element......................................................... 10

6. Operating the Machine.........................................................................11

7. Adjustments ........................................................................................ 12

8. Maintenance & Lubrication ................................................................ 14

9. Troubleshooting Guide........................................................................ 16

10. Wiring Diagram .................................................................................. 19

-1-

1. Safety Instructions

THIS MANUAL GIVES YOU INFORMATION ON SAFETY INSTRUCTIONS,
SPECIFICATIONS, OPERATION AND MAINTENANCE OF STRAPPING
MACHINES.

BEFORE OPERATING OR SERVICING THE MACHINE, PLEASE REVIEW THE
ENTIRE MANUAL AND FOLLOW THE SAFETY INSTRUCTIONS CAREFULLY.

(1) Before Operating

a. Verify that the power line voltage is correct.
b. The machine must be properly grounded to avoid a shock hazard. All wiring must be

in accordance with local wiring standards.

c. The strapping machine can only be operated with polypropylene (P.P.) strapping; do

not use polyester (PET) strapping or polyethylene (PE) cord strap.

(2) During Operation

a. The weight of the package cannot exceed 100 kg (220 lbs).
b. The size of the package should not be less than 80mm (width) × 20mm (high) (3.16＂

×0.79＂).

c. Check if the machine emits any smokes or unusual sound when it is running.

(3) After operating

a. Remove dust and dirt from the unit; pay particular attention to the interior of the arch.
b. Turn off the power when the machine is not in use.

(4) Signs

(5) Maintenance

a. Turn off the power before removing either of the top covers.
b. Use the correct tools and parts to repair the machine.
c. The heater tongue is very hot; do not touch it.

Caution!
Electric Shock Hazard

Caution!
Hot!
Do not touch!

-2-

(6) Storage

a. The store room must be dry.
b. Do not expose the machine to extreme cold or heat environment.
c. Place the machine on an even floor in order to avoid any distortion.

(7) Other Reminders

a. Do not alter or bypass protective interlocks.
b. An operation manual must remain attached to the machine at all times.
c. Do not alter the equipment or circuitry unless authorized to do so by the manufacturer.
d. Do not operate the machine with the table tops or covers removed.
e. Never put any part of your body near, under or into a moving machine.
f. Do not overload the machine by exceeding the performance limitations specified in

this manual.

2. Construction and Units

Strapping head unit

Control Panel

Reel unit

Body frame unit

-3-

3. General Safety Remarks

(1) Basic Operation

The manual and the safety remarks are to be read before use. The operator manual should
be kept with the machine at all times. Intervals for maintenance and inspections are to be
adhered to.
This machine was built with state of the art technology and rigid adherence to safety
standards.
Unless used properly, it can cause injury to operators or persons in close proximity to the
machine. In addition, improper use can cause damage to the machine or property around
the machine.

(2) Basic Safety Precautions

The user is to be instructed in all other generally applicable legal and other mandatory
regulations relevant to accident prevention and environmental protection in addition to the
operating instructions.

For safety reasons, long hair must be tied back or otherwise secured, garments must be
close fitting and no jewelry may be worn.

Use protective equipment whenever required by circumstances or by law.

Carefully observe all safety instructions and warnings attached to the machine and make
sure that they are always complete and perfectly legible.

Always make certain that persons being trained and instructed in working on or with the
machine are permanently supervised by an experienced person.

Work on the electrical system and equipment of the machine is only to be carried out by a
skilled electrician or by persons under the supervision and guidance of a skilled electrician
and in accordance with the rules and regulations of electrical engineering.

(3) Safety Instructions Governing Specific Operational Phases

Avoid any operation mode that might be unsafe.

All necessary precautions to ensure that the machine is only used being in a safe and
reliable state are to be taken. The machine is only to be operated if all protective and
safety devices, including removable safety devices, emergency shut-off equipment,
noise-protection elements and exhaust systems are in right place and fully functional.

The machine is to be checked for damage and defects at least once per work shift. Any
changes including the working behavior of the machine are to be reported to competent

-4-

persons immediately. If necessary, the machine is to be stopped and locked immediately.
In case of any malfunction the machine must be stopped and locked until the defect has
been eliminated.

Generally make sure that nobody is at risk before starting up the machine.
All personnel that will be operating this machine should be thoroughly trained in all
phases of operation and safety.

Always tighten unscrewed connections after maintenance and repair.

After completing maintenance and repair, all safety devices removed for setting up or
repairing the machine must be reinstalled and checked for functionality prior to putting the
machine back into service.

To minimize the environmental impact all consumables and replaced parts must be
disposed of safely.

Before starting the machine, check that the accessories have been stowed away safely.

Do not attempt any operation that may be a risk to the stability of the machine.

(4) Warning of Electrical Dangers

Immediately remove power to the machine in case of trouble in the electrical system.
Replace a fuse with one with the same style and ratings; pay particular attention to
matching the specified current.

Any electrical work performed on the equipment must be conducted by a skilled
electrician or under the supervision of a skilled electrician. All work must be observed
good electrical engineering practice and follow safety rules and local wiring standards.

Inspect the electrical equipment of the machine at regular intervals. Tighten any loose
connections. Check wiring for scorch marks; replace scorched wiring and determine and
correct the reason for the overheating.

When working on live equipment, ensure that a second person is available to cut power in
case of an emergency. When appropriate, secure the working area with safety tape and a
warning sign. Use insulated tools for electrical work.

Before working on high-voltage assemblies, turn off the power supply. Carefully discharge
the supply cable and short-circuit any energy-storage components such as capacitors.

If the equipment was moved, carefully refit and refasten all parts removed for transp ort
before reapplying power.

Before moving the machine, remember to disconnect the power cable.

-5-

(5) Grounding Instructions Shall Include the Following

This product must be grounded. In the event of an electrical short circuit, grounding
reduces the risk of electric shock. This product is equipped with a cord that has a
grounding wire and an appropriate grounding plug. The plug must be plugged into an
outlet that is properly installed and grounded in accordance with all local codes and
ordinances.

If repair or replacement of the cord or plug is necessary, connect the ground wire to the
ground terminal of the plug. The wire with green insulation (with or without yellow stripes)
is the grounding wire.

Check with a qualified electrician or service person if the grounding instructions are not
clear or if in doubt about the proper grounding of the machine. Do not modify the plug
provided; if it will not fit the power outlet, have the proper outlet installed by a qualified
electrician.

This product is designed for use on a nominal 120 (230) volt AC circuit and has a
grounding plug.

DANGER!
Improper installation of the grounding can result in electrocution.

4. Machine Information

(1) Areas of Application and Machine Description

This plastic strapping machine can be used for a wide range of applications where the
minimum package width is at least 80mm, and the minimum height is 20mm.
This machine is particularly suitable for heavy packaged goods as well as printed products,
boxes, etc.

Machine Description

Semi-automatic plastic strapping machine for use with polypropylene strapping.
Heavy duty construction.
Simple, safe and user-friendly operation.
Moveable, with large table area high capacity strap reel and stainless steel table.
Two locking castors, to ensure safe operation.

-6-

Environment Information
The strapping machine shall be installed in the following conditions:

 Supply voltage: 0.9 - 1.1 nominal supply voltage
 Source frequency: 0.99 - 1.01 nominal frequency
 Ambient temperature: 5°C - 40°C (41℉-104℉).
 Relative humidity: not exceed 50% at 40°C.
 Please provide a suitable illumination around the machine for safety operation.

(2) The Safety Devices

Caution!

The heating unit operates at a very high temperature in order to melt the P.P. strapping.
To prevent burns, avoid contact with this area. (1)

To move the machine, the two lockable casters (2) must be unlocked. Relock the two
casters when the machine is in its new position.

Description of the Safety Devices

The machine is turned on when it is connected to AC power and the main power switch
(QS1), located on the front operating panel, is placed in the ON position. After
approximately 3 minutes, the heating element will reach its operating temperature and the
machine will be ready for use.

If it is necessary to make adjustments inside the machine during operation, after a strap
jam for example, the table top can be unscrewed. Observe caution as the machine is still
fully functional with the covers removed. If machine with safety switch, when table top is
opened, safety switch is activated. This will remove power but heating element is keeping
heating.

1

2

-7-

(3) Electrical Specifications

System configuration：

1L+N+PE (Ground) 1L+N+PE (Ground)

Nominal power：

0.5 KW 0.5 KW

Rated current：

7A 10A

Rated voltage：

220V/230V/240V 110V

Rated frequency：

50Hz 60Hz

Type of current：

AC - single phase AC - single phase

Minimum Requirements

The electrical supply line for the machine must have a minimum cross-section of at least
3C × 1.0mm2.

(4) Technical Data

a. TP-201 / TP-201CE

b. TP-202 / TP-202CE

MODEL TP-201 / TP-201CE
Sealing method Heat
Net Weight 100kg (220 lbs)
Max. Tension 45kg (99 lbs)
Strap Width 6mm to 15.5mm (1/4" to 5/8")
Noise emission 78 dB (A)
Ambient temp

5 C~ 40 C (41 F ~ 104 F)

MODEL TP-202 / TP-202CE
Sealing method Heat
Net Weight 85kg (187 lbs)
Max. Tension 45kg (99 lbs)
Strap Width 6mm to 15.5mm (1/4" to 5/8")
Noise emission 78 dB (A)
Ambient temp

5 C~ 40 C (41 F ~ 104 F)

-8-

c. TP-202L / TP-202LCE

d. TP-203 / TP-203CE

e. TP-201Y / TP-201YS

MODEL TP-202L / TP-202LCE
Sealing method Heat
Net Weight 80kg (176 lbs)
Max. Tension 45kg (99 lbs)
Strap Width 6mm to 15.5mm (1/4" to 5/8")
Noise emission 78 dB (A)
Ambient temp

5 C~ 40 C (41 F ~ 104 F)

MODEL TP-203 / TP-203CE
Sealing method Heat
Net Weight 80kg (176 lbs)
Max. Tension 9kg ~ 30kg (19.8 lbs ~ 66.1 lbs)
Strap Width 6mm to 15.5mm (1/4" to 5/8")
Noise emission 78 dB (A)
Ambient temp

5 C~ 40 C (41 F ~ 104 F)

MODEL TP-201Y / TP-201YS
Sealing method Heat
Net Weight 125kg (275 lbs)
Max. Tension 45kg (99 lbs)
Strap Width 6mm to 15.5mm (1/4" to 5/8")
Noise emission 78 dB (A)
Ambient temp

5 C~ 40 C (41 F ~ 104 F)

-9-

(5) How to Remove/Handle the Machine from the Pallet

Two people stand on each side of the machine and remove the machine from the pallet to
the floor.

-10-

5. Machine and Operating Element

(1) Power Switch

The motor starts running when this switch is turned ON.

(2) Feeding Length Knob

Strap is automatically fed during the time preset by the knob.

(3) Reset Button

To pull strap back into machine and / or to cut off strap.

(4) Strap Feed Button

To feed strap out of machine freely.

(5) Power Plug

To be connected to a 110V or 220V/230V/240V source.

(6) Strap Reel

Slide on strap coil here. (If strap core is 280mm, you can
take off the center drum to have core size 200mm.)

(7) Brake

Stops the over-rotation of the Strap reel.

(8) Strap Guide for Brake

The strap is threaded through this guide.

(9) Strap Bypass Guide

The strap is passed through this guide.

(10) Strap Insertion Inlet

This is the strap inlet at which the leading strap end is
detected.

(11) Tension control

Turn clockwise to increase tension and counter clockwise to
decrease tension

11

-11-

6. Operating the Machine

(1) Operation Space

Keep the area (A) and (B) free for the operator.
The area (A) is necessary for operation strapping machine or changing the strap coil
(TP-202).
For TP-201/TP-203, the area (B) is necessary for changing the strap coil.

(2) How to Load and Thread P.P. Strap

a. Turn reel nut handle (A) left and remove it.
b. Remove the outer flange (B) and install the strap reel.
c. Make sure that the direction of rotation is counterclockwise (E) when unrolling.
d. Put the outer flange back on and tighten reel nut handle (A) to the right.
e. Remove all adhesive strips or other adhesive material.
f. Unroll about 1.5 m of strap and make sure that it is not twisted.
g. Thread the strap over (C) to roller (D) in direction of the arrow.
h. Turn left button (strap feed) to the left until obtaining the length you need.

A

A

B

TP-202 TP-201 / TP-203

D

C

B

A

E

B

-12-

(3) How to Operate

a. Turn the power switch ON. The heating element reaches the working temperature at

approximately 3 minute.

b. Place a package on the table top (The package must cover the Slide Table).
c. Properly adjust the strap tension according to various package.
d. Place the strap around the package to be strapped and insert the strap into the strapping

head until it stops.

e. The strapping and welding sequence should complete.
f. At end of strapping sequence the strap end is fed automatically, and Feeding Length

Knob is to adjust the strap length.

7. Adjustments

(1) Strap W i dth

Adjustment for strap in different width can be done with only one Philips recess
screw driver and a hex spanner. The adjustment must be made in two places, A (Strap
Outlet), B (Strap Inlet) as shown below.
For A, the width of band guide should be at 12.5mm to 13.0mm when using 9mm and
12mm strap and the width of band guide should be at 15.5mm to 16mm when using 15mm
strap.
For B, The width of band guide should be wider by 0.5mm to 1.0mm than the actual
strap width.

The adjustment is made with the
guide located on the top of the
table. Make both adjustments
by loosening two screws and
applying the strap which is to be
used.

Fig. A Strap Outlet

Fig. B Strap Outlet

-13-

(2) Inside Tension Adjustment (For TP-201Y)

Tensioning strength should be adjusted properly by observing the tension of the strap
applied around the package.
The adjustment is made by tensioning adjustment nut A. Tensioning adjustment nut A is
turned clockwise to increase the strength and counterclockwise to decrease strength.
After adjustment, nut A should be fixed by a set screw.

(3) Outside Tension Adjustment (For TP-201/TP-202/TP-203/TP-202L)

The adjustment is made by tensioning adjustment nut A which is located at the back of the
machine.
Tensioning adjustment nut A is turned clockwise to increase the strength and
counterclockwise to decrease strength.

-14-

(4) Heater temperature

Set the knob to position 3 or 4. Adjust the heater temperature by selecting a position
between l and 6. Choose the suitable temperature, bearing in mind the environmental
conditions of the machine. If the heater temperature is too high or too low, a proper seal
will not be obtained.
Gradually increase or reduce the position until obtaining an optimum seal.

8. Maintenance & Lubrication

Warning:
Before any maintenance or repairs on the machine, set the Power Switch to
"O" (OFF). Wait about 5 minutes for cooling down the heater to avoid burns
with this area.

(1) Cleaning and Lubrication

The high reliability and long service life of the strapping machine will depend on regular
cleaning and maintenance.

ATTENTION!
All the important strap transport components, such as the tension rollers and the
strap guides, must be kept free from oil and grease. (lubricant)

The lubricant has to be non-resinous.
The lubricant is SAE 30

-15-

(2) Maintenance

Only use original spare parts supplied by manufacturer.

Daily:

Use air gun to clean the circled positions (nearby the cutters, strap guide daily
Remove plastic residue in the machine.

Weekly:

Lubricate front bar, press bar and rear bar weekly.
Please refer to the above mesh areas for instruction.

Before lubricating, be sure to clean the parts first to avoid mixing oil and debris which
might have a bad effect on machine’s function.

Monthly :( or 3,000 strapping cycles)

Clean both sides of heater plate and polish with fine sandpaper if necessary

ATTENTION: Make sure the welding plate is cool first!!

Check cam rollers of seal head for easy movement. Slide table back to home position
automatically by the spring tension.
Be sure to clean any debris in the tension roller

6 Months:（or 18,000 strapping cycles）

Check heater plate, replace and readjust it if necessary.
Check strap cutter in seal head, replace it if necessary.
Check that connector at wiring loom to printed circuit board is firmly fixed.
Make machine ready for operation. Strap one bundle manually several times, paying
attention to mal-functions, repeat procedure.

Air Air

-16-

1 year :( or 36,000 strapping)

Replace deflection roller if it shows visible changes.
In case of loud noise at bearings: locate them, replace the bearings.
Get machine ready for operation again, strap one bundle manually several times, paying
attention to malfunctions.

9. Troubleshooting Guide

(1) Strap Jams in the Groove

Step1. Turn the power switch off and pull out the strap strongly in tensioning direction.

-17-

Step2. In case this remedy does not work due to strap jam, follow the instructions listed

below.

a. Loosen M5 Set screw (Part No. 5)
b. Remove Pin (Part No. 6) then lift Holder (Part No. 7) and repeat step 1. If this is

not successful, continue

c. Remove Strap Inlet Guides (Page 12 (B))
d. Remove M6 Hexagon Bolts (Part No. 3)
e. Remove Holder Arm (Part No. 4) from Holder (Part No. 7)
f. Lift out Holder (Part No. 7) and eliminate jam.
g. Reassemble from (f.) back to (a.)

-18-

(2) The Strap Does Not Feed Past the Infeed Guide

This failure is caused if the front bar is in the raised position (previous cycle has not been
completed). Turn the Power switch "off ", then "on" again.
If this does not eliminate the failure, adjust the lever for LS1 to allow LS1 to be activated
and de-activated correctly.

*More troubleshooting guide is on request.

-19-

10. Wiring Diagram

PART Ⅱ

CONTENTS

1. Spare Parts List …………………………………1

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

1 TA-900 Strapping Head Unit (For TP-202) 1

TA-901 Strapping Head Unit (For TP-201) 1
TA-901S Strapping Head Unit (Stainless Steel

Model)(For TP-201CES)

1

TA-902 Strapping Head Unit (For TP-201Y) 1
TA-902S Strapping Head Unit (Stainless Steel

Model)(For TP-201YS)

1

TA-903 Strapping Head Unit (For TP-203) 1
2 T5-1-10110 Main Body Block 1
3 TA-003 Cam Shaft 1
4 KYA050530 Key, 5×5×30 1
5 KYA0505101 Key, 5×5×101 1
6 KYA050515 Key, 5×5×15 2
7 ER12 Snap Ring, E-12 3
8 TA-008-2 Bearing Support (L) 1
9 HBS0620 HBS, M6×20 6

10 HBS0645H HBS, M6×45 (H) 1

11 BR6003ZZ Bearing, 6003ZZ 4
12A TA-012A Grip Cam 1
12B TA-012B Grip Cam 1

13 HSS0608G HSS, M6×8 (G) 13

14 TA-014 Separator Cam 1
15A TA-015A Rear Bar Cam 1
15B TA-015B Heater Cam 1

16 TA-016 Sprocket 1

17 TA-017-2 Bearing Support (R) 1

18 TA-018 Pulley 1

20 TA-020 Pulley 1

22 TA-022 Chain 1

23 TF-002 Micro Switch Bracket 1

24 TA-024 Back Cam 1

25 TA-025 Collar 1

27 TA-027 Sprocket 1

28 TA-028 Housing 1

-2-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

29 TA-029 Pin 1

30 TA-030 Holder 1

31 PMS0408 PMS, M4×8 6

32 TA-032 Spring 1

33 TA-033 Stop Arm 1

34 TA-034 Clutch Arm 1

35 TA-035 Shaft 1

36 KYA050520 Key, 5×5×20 1

37 TA-037 Clutch Support 1

38 HBS0616 HBS, M6×16 14

39 TF-009 Switch Trigger 1

40 TA-040 Guide 1

41 PMS0420 PMS, M4×20 1

42 TA-042 Gear Box 1

43 HBS0820 HBS, M8×20 4

44 TF-022 Washer 1

45 KYA050525 Key, 5×5×25 2

58 TA-058 Pull Shaft 1

59 SW06 SW, M6 19

60 TA-060 Solenoid Shaft 1

61 SP0414 Spring Pin, 4×14 1

62 TF-028 Fan 1

63 HBS0510 HBS, M5×10 4

67 TA-067 Bar Guide Lid 1

69 TA-069 Press Bar 1

TA-069S Press Bar (Stainless Steel Model) 1
70 SP0318 Spring Pin, 3×18 3
71 TA-071 Return Spring 3
72 TA-072 Spring Hook 1
73 TA-073 Spring Hook 3
74 TA-074 Rear Bar 1

TA-074S Rear Bar (Stainless Steel Model) 1

-3-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
75 TA-075 Plunger 3

76 BR635ZZ Bearing, 635ZZ 4
77 SP0514 Spring Pin, 5×14 3
78 TA-078 Spring 3
79 TA-079 Front Bar 1

TA-079S Front Bar (Stainless Steel Model) 1
80 TA-080 Slide 1

TA-080S Slide (Stainless Steel Model) 1
81 HBS0505.2 HBS, M5×5.2 1

HBS0505.2S HBS, M5×5.2 (Stainless Steel Model) 1
82 SP0314 Spring Pin, 3×14 1

84 PMS0315 PMS, M3×15 6
85 HN08 HN, M8 2
86 TA-086 Seal 1
87 TA-087 Switch Lever 1
88 TA-088 Seal (Small) 1
89 TA-089 Spring Hook 1
90 TA-090 Arm 1
91 SP0620 Spring Pin, 6×20 1
92 HBS0525 HBS, M5×25 1
94 TA-094 Shaft 1
95 TA-095 Guide (L) 1

TA-095S Guide (L)(Stainless Steel Model) 1
96 HBS0512 HBS, M5×12 4

HBS0512S HBS, M5×12 (Stainless Steel Model) 4

99 TF-001 Motor (For 110V/60HZ) 1

TF-001-1D Motor (For 220V/50HZ) 1

TF-001-1B Motor (For 220V/60HZ) 1

TF-001-2 Motor (For 240V/50HZ) 1

TF-001-B Motor (For 100V, 50/60HZ) 1

-4-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

114 TA-114 Spring 1
115 TA-003A Cam Ass'y 1
116 TA-035A Stop Arm Ass'y 1
117 TA-058A Pull Shaft Ass'y 1
118 TA-080A Slide Ass'y 1

TA-080AS Slide Ass'y (Stainless Steel Model) 1

119 TA-083A Separator Ass'y 1

TA-083AS Separator Ass'y (Stainless Steel Model) 1

120 TF-002A Micro Switch Bracket Ass'y 1
121 TF-003A D.C.Solenoid Ass'y (For 110V) 1

TF-003A-1 D.C.Solenoid Ass'y 1

(For 220V/230V/240V)
122 T5-1-13000 Rear Bar Ass'y 1
123 T5-1-14000 Press Bar Ass'y 1
124 T5-1-15000 Front Bar Ass'y 1

226 TA-226 Guide (R) 1

TA-226S Guide (R)(Stainless Steel Model) 1
227 TB-114 Return Spring 1
228 TA-228 Belt 1
229 TA-229 Collar 2

236 TA-236 Rubber Buffer 1

238 ER03 Snap Ring, E-3 1
239 TA-239 Cutter Holder 1
240 HBS0516 HBS, M5×16 4
241 TA-241 Spacer 3

244 HSS0506G HSS, M5×6 (G) 2
245 HSS0606G HSS, M6×6 (G) 2
246 PW06C PW, M6 (C) 16
247 HN06 HN, M6 6
248 HN04 HN, M4 1
249 SW04 SW, M4 4

-5-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
250 SW05 SW, M5 5

251 PW05 PW, M5 2
252 HBS0525H HBS, M5×25 (H) 1
253 HN05 HN, M5 2
254 SW08 SW, M8 5
255 HN03 HN, M3 3
256 PW06A PW, M6 (A) 2
258 TF-044 Start Capacitor (220V/50HZ) 1

TF-045 Start Capacitor (220V/60HZ,

240V/50HZ)

1

TF-046 Start Capacitor (110V/60HZ) 1

TF-047 Start Capacitor (100V/50HZ,

100V/60HZ)

1

259 TF-006 Micro Switch (LS-1, LS-3) 2
260 LA-50082 Label (LS-3) 1
261 LA-50080 Label (LS-1) 1
262 SW03 SW, M3 8
263 LA-50084 Label (SOL-2) 1
264 TF-071 Varistor 1
265 PW08C PW, M8 (C) 4

-6-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
101 PW04 PW, M4 2

102 TB-102 Heater Arm 1
103 TB-103 Pin 1
104 HN08 HN, M8 1
105 ER06 Snap Ring, E-6 1
106 HBS0440H HBS, M4×40 (H) 2
107 TB-107 Side Plate 1

113 TB-113 Heater Ass'y 1
114 TB-114 Return Spring 1
115 TB-115 Spring 1
117 TB-117 Roller 4
118 TB-118 Shaft (For Inside Tension Adjustment) 1

TB-118A Shaft (For Outside Tension

Adjustment)

1

119 SR15 Stop Ring, S-15 10
120 KYA050515 Key, 5×5×15 9
121 HSS0506G HSS, M5×6 (G) 2
122 TB-122 Shaft 1
123 TB-123 Holder 1
124 TB-124 Pin 1
125 HSS0606G HSS, M6×6 (G) 1
126 HSS0508G HSS, M5×8 (G) 3
127 TB-127 Gear 3
128 TB-128 Collar 7
129 TB-129 Feed Gear 1
130 TB-130 Spring 1
131 HB06100 HB, M6×100 1
132 HN06 HN, M6 12
133 TB-133 Nut 1
134 TB-134 Gear 1
135 TB-135 Holder Arm 1
136 HBS0616 HBS, M6×16 4
137 TB-137 Shaft 1
138 KYA050520 Key, 5×5×20 2
139 TB-139 Pulley 1
140 RR22 Snap Ring, H-22 1

-8-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
141 TB-141 Pulley 2

142 BR608ZZ Bearing, 608ZZ 1
143 TB-143 Round Belt 1
144 TB-144 Shaft 1
145 ER07 Snap Ring, E-7 1
146 TB-146 Arm 1
147 RR32 Snap Ring, H-32 2
148 TB-148 Bracket 1
149 TB-123B Roller Holder Ass'y 1
150 TB-210A Roller Bracket Ass'y 1
151 PMS0315 PMS, M3×15 2
152 TB-152 Shaft 1
154 TB-154 Spring 1
155 TB-155 Nut 1
156 BR6002ZZ Bearing, 6002ZZ 12
157 TB-157 V-Belt 1
158 TB-158 Bracket 1
159 HBS0620 HBS, M6×20 6
160 TB-160 Bracket 1
161 TB-158A Bracket Ass'y 1
162 TB-162 Shaft 1
163 KYA050538 Key, 5×5×38 1
164 TB-164 Shaft 1
165 TB-165 Feed Arm 1
166 SP0520 Spring Pin, 5×20 1
167 BR635ZZ Bearing, 635ZZ 3
168 TB-168 Arm Pin 1
169 SW04 SW, M4 6
170 TB-170 Pulley 1
171 TB-160B Bracket Ass'y 1

173 TB-173 V-Belt 1
174 TB-165A Feed Arm Ass'y 1
175 TB-175 Plate 1

175A TB-175A Plate 1

176 TB-176 Friction Disc 2

TJ-025 Friction Disc (Only TP-203) 2

-9-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
177 TB-177 Pull Shaft 1

178 TB-170A Pulley Ass'y 1
179 TB-177A Pull Shaft Ass'y 1
180 PW06A PW, M6 (A) 18
181 SP0414 Spring Pin, 4×14 1

182 SP0408 Spring Pin, 4×8 1

183 TB-183 Spring 1
184 TB-184 Stop Bracket 1
185 HBS0510 HBS, M5×10 6
186 TB-186 Spring 1
187 TB-187 Spring 1
189 TB-189 Retainer 1

192 TB-192 Roller 1
193 TB-193 Cover 1
195 TB-195 Outlet Cover 1
196 PMS0410 PMS, M4×10 7
197 TB-197 Guide Front 1
199 TB-199 Pin 1
200 SR10 Stop Ring, S-10 2
201 TB-201 Outlet Guide 1
203 TB-203 Guide 1

TB-203L Guide (Longer)(Option) 1
204 FMS0408 FMS, M4×8 10
205 TB-205 Guide 1
206 TB-206 Cover 1
207 TB-207 Cover-Side 2
208 TB-208 Front Plate 1
209 TB-209 Band Plate 1
210 TB-210 Pulley 1
212 RR19 Snap Ring, H-19 1
213 HBS0525H HBS, M5×25 (H) 1
215 TB-215 Collar 1
216 HB0680 HB, M6×80 1
220 PMS0412 PMS, M4×12 3
221 HN05 HN, M5 3

-10-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
223 TB-223 Washer 2

224 TB-224 Spring Retainer 2
225 TB-225 Bush 1

231 TB-231 Pin 1
232 TB-232 Bracket 1
234 HBS0665H HBS, M6×65 (H) 1

247 HBS0506 HBS, M5×6 1
248 TB-248 Spring Retainer 1
249 BR6005ZZ Bearing, 6005ZZ 1
250 TB-250 Tube A 1
251 TB-251 Tube B 1

TJ-251 Tube B (Only TP-203) 1
254 HBS0512 HBS, M5×12 2
255 TB-255 Fix Arm (Only TP-201) 1
256 TB-256 Corrector 1
257 TB-257 Fix Arm (For TP-202/TP-202L) 1
258 TB-258 Bolt (For TP-202/TP-202L) 1
260 T7-3-40480 Spring (Only TP-201Y) 1
262 TB-262 Tube 1
263 HBS0516 HBS, M5×16 1
264 HSS0606G HSS, M6×6 (G) 1
265 SW08 SW, M8 1
266 HN04 HN, M4 7
267 PW04 PW, M4 3
268 SW05 SW, M5 6
269 SW06 SW, M6 15
270 PW05 PW, M5 1
271 SW03 SW, M3 2
272 TF-007 Micro Switch (LS-2) 1
273 LA-50081 Label (LS-2) 1
274 LA-50083 Label (SOL-1) 1
275 TF-071 Varistor 1

-11-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
276 FLG06 FLG, M6 6

277 TF-003A D.C. Solenoid Ass'y (For 110V) 1

TF-003A-1 D.C. Solenoid Ass'y 1

(For 220V/230V/240V)
278 TB-263 Tube 1
279 FMS0406 FMS, M4×6 2
280 TA-060 Solenoid Shaft 1
281 TA-086 Seal 1
282 ER12 Snap Ring, E-12 1
283 TB-264 Tension Adjusting Ass'y 1

TJ-252 Tension Adjusting Ass'y (Only TP-203) 1

-12-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

1 TE-001 Inner Flange 1
2 TC-014 Outer Flange 1
3 TE-003 Shaft 1
4 TC-015 Protector 1
5 TB-255-1 Rubber 1

7 TC-016 Reel Nut Handle 1
8 TC-004 Package Guide 1

10 TE-010 Grommet 2
11 TE-011 Caster (Free) 2
12 TE-012 Caster (Brake) 2
13 TE-013 Lock Pin 4

TE-013S Lock Pin (Stainless Steel Model) 4
14 TE-014 Brake Holder (R) 1
15 TC-002 Bracket 1
16 TC-008 Grommet 1
17 TE-017 Bush (L) 1
18 TE-018 Bush (R) 1
19 TC-020 Pin 1
20 TC-021 Split Pin 1
21 TE-021 Brake Set 1
22 TE-022 Pin 1
23 TE-023 Rubber Stop 1
24 TE-024 Brake Holder (L) 1
25 TE-025 Spring 1
26 ER04 Snap Ring, E-4 2
27 TE-027 Roller Holder 1
28 TE-028 Roller 1
29 TE-029 Pin 1
30 TE-030 Band Guide Bracket 1
31 TC-049 Roller 1
32 TC-048 Shaft 1

38 TMS0508 TMS, M5×8 (Only CE) 6
40 TE-033 Right Side Plate (Only CE) 1

-14-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
41 TE-041 Body Frame 1

TE-041S Body Frame (Stainless Steel Model) 1

TK-033 Body Frame (Only CE) 1

TK-033S Body Frame (Stainless Steel Model)

(Only CE)

1

42 TE-042 Magnet Catch 4
43 TE-043 Side Door (L) 1

TE-043S Side Door (L)(Stainless Steel Model) 1
44 TE-044 Side Door (R) 1

TE-044S Side Door (R)(Stainless Steel Model) 1
45 TE-045 Support 1

TE-045S Support (Stainless Steel Model) 1
46 TC-043 Top Plate 1

TC-043S Top Plate (Stainless Steel Model) 1
47 TE-001A Reel Unit 1
48 TE-021A Brake Arm Ass'y 1
49 TE-030A Band Guide Bracket Ass'y 1

51 HB0612 HB, M6×12 20

53 TMS0305 TMS, M3×5 8

55 HBS0620 HBS, M6×20 7
56 HB0620 HB, M6×20 2
57 SW06 SW, M6 27
58 SR10 Stop Ring, S-10 3
59 PW06C PW, M6 (C) 30
60 PW06A PW, M6 (A) 2
61 PW06B PW, M6 (B) 2

63 WN06 WN, M6 2
64 HN06 HN, M6 11

67 TMS0612 TMS, M6×12 1
68 TC-068 Collar 1
69 NTE06 NTE, M6 2
70 TC-070 Shaft 2

-15-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
71 FMS0612 FMS, M6×12 1

73 T5-2-10170 Hinge 1

75 TC-075 Center Drum 280mm 1
76 TC-076 Washer 1
77 ER19 Snap Ring, E-19 1
78 TB-205 Guide 1

84 HBS0612 HBS, M6×12 2
85 TMS0408 TMS, M4×8 2
86 SW04 SW, M4 2
87 HN04 HN, M4 2

89 PW05 PW, M5 4
90 SW05 SW, M5 4
91 HN05 HN, M5 4

94 HB0610 HB, M6×10 1
95 PMS0408 PMS, M4×8 2
96 LA-31010 Label 1

-16-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

1 TC-001 Protection Cover 1
2 TC-002 Bracket 1
3 TC-003 Reel Shaft 1
4 TC-004 Package Guide 1
5 TC-005 Lid 5
6 TC-006 Caster (Free) 2
7 TC-007 Caster (Brake) 2
8 TC-008 Grommet 1

9 TC-009 Brake Shaft 1
10 BR6003ZZ Bearing, 6003ZZ 2
11 TC-011 Washer 1
13 TC-013 Inner Flange 1
14 TC-014 Outer Flange 1
15 TC-015 Protector 1
16 TC-016 Reel Nut Handle 1

18 TC-018 Brake Lining 1
19 TC-019 Roller 1
20 TC-020 Pin 1
21 TC-021 Split Pin 1
22 TC-022 Roller Holder 1
24 TC-024 Brake Adjuster 1
25 TC-025 Spring 1
30 T7-5-10160 Adjustment Leg (Option) 4
31 TC-031 Fix Plate (Option) 4
32 T5-3-11000 Reel Control Group 1
33 TC-047A Roller Bracket Ass'y 1

38 TMS0508 TMS, M5×8 6
39 SW16 SW, M16 4
41 TC-041 Body Frame 1

TK-031 Body Frame (Only CE) 1
42 TC-042 Support 1
43 TC-043 Top Plate 1
44 TC-044 Reel Support 1

-18-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
45 TC-045-1 Fixing Brake Lining Bracket 1

46 TC-046-1 Arm 1
47 TC-047 Roller Bracket 1
48 TC-048 Shaft 1
49 TC-049 Roller 1
50 TC-050 Lining Holder 1
51 HB0612 HB, M6×12 4
52 PW06C PW, M6 (C) 14
53 FMS0512 FMS, M5×12 2
54 HBS0620 HBS, M6×20 7
55 SW05 SW, M5 2
56 PW06A PW, M6 (A)(Option) 8

57 PW05 PW, M5 2
58 SW06 SW, M6 10

SW06 SW, M6 (Option) 18
59 SW08 SW, M8 4
60 HBS0616 HBS, M6×16 2

HBS0616 HBS, M6×16 (Option) 10
61 WN06 WN, M6 2
62 HN06 HN, M6 9
63 HBS0816 HBS, M8×16 4
64 HB0816 HB, M8×16 1
65 SR20 Stop Ring, S-20 2
66 SR10 Stop Ring, S-10 2
67 TMS0612 TMS, M6×12 1
68 TC-068 Collar 1
69 NTE06 NTE, M6 2
70 TC-070 Shaft 2
71 FMS0612 FMS, M6×12 1

73 T5-2-10170 Hinge 1
74 PW06B PW, M6 (B) 2
75 TC-075 Center Drum 280mm 1
76 TC-100 Adjustment Leg Ass'y (Brake)(Option) 2
77 TC-110 Adjustment Leg Ass'y (Free)(Option) 2
78 TB-205 Guide 1

-19-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
79 TC-076 Washer 1

80 ER19 Snap Ring, E-19 1
81 HBS0525H HBS, M5×25 (H) 1
82 HN05 HN, M5 4
83 PMS0416 PMS, M4×16 4
84 PW04 PW, M4 4
85 TMS0408 TMS, M4×8 2
91 SR15 Stop Ring, S-15 1
92 TC-092 Holder 1
93 LA-50094 Label (Option) 4
94 HN05 HN, M5 2
95 HB0610 HB, M6×10 1
96 TC-094 Spacer 1
97 LA-31010 Label 1

-20-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

1 TD-001 Protection Cover 1
2 TC-002 Bracket 1
3 TD-003 Reel Shaft 1
4 TC-004 Package Guide 1
5 TC-005 Lid 5
6 TC-006 Caster (Free) 2
7 TC-007 Caster (Brake) 2
8 TC-008 Grommet 1

9 TC-009 Brake Shaft 1
10 BR6003ZZ Bearing, 6003ZZ 2
11 TC-011 Washer 1
13 TC-013 Inner Flange 1
14 TC-014 Outer Flange 1
15 TC-015 Protector 1
16 TD-016 Reel Nut Handle (LH) 1

18 TD-018 Brake Lining 1
19 TC-019 Roller 2
20 TC-020 Pin 1
21 TC-021 Split Pin 1
22 TC-022 Roller Holder 1
24 TD-024 Spring Hook 1
25 TC-025 Spring 1

38 TMS0508 TMS, M5×x8 6
39 SW16 SW, M16 4
41 TD-041 Body Frame 1

TK-041 Body Frame (Only CE) 1
42 TC-042 Support 1
43 TC-043 Top Plate 1
44 TD-044 Reel Support 1
45 TC-045-1 Fixing Brake Lining Bracket 1
46 TD-046-1 Arm 1
47 TD-047 Roller Bracket 1
48 TD-048 Shaft 1
49 TD-044A Reel Support Ass'y 1

-22-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
50 TC-050 Lining Holder 1

51 HB0612 HB, M6×12 2
52 HB0610 HB, M6×10 2
53 FMS0512 FMS, M5×12 2
54 HBS0620 HBS, M6×20 7
55 SW05 SW, M5 2
56 PW06C PW, M6 (C) 14
57 PW05 PW, M5 2
58 SW06 SW, M6 14
59 TD-047A Roller Bracket Ass'y 1
60 PW06B PW, M6 (B) 2
61 WN06 WN, M6 2
62 HN06 HN, M6 9
63 HBS0616 HBS, M6×16 5
64 HB0816 HB, M8×16 1
65 SR20 Stop Ring, S-20 2
66 SR10 Stop Ring, S-10 3
67 TMS0612 TMS, M6×12 1
68 TC-068 Collar 1
69 NTE06 NTE, M6 2
70 TC-070 Shaft 2
71 FMS0612 FMS, M6×12 1
72 PW06A PW, M6 (A) 2
73 T5-2-10170 Hinge 1

75 TC-075 Center Drum 280mm 1
76 TC-076 Washer 1
77 ER19 Snap Ring, E-19 1
78 TB-205 Guide 1

81 HBS0525H HBS, M5×25 (H) 1
82 HN05 HN, M5 4
83 PMS0416 PMS, M4×16 4
84 PW04 PW, M4 6

-23-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
91 SR15 Stop Ring, S-15 1

92 TMS0408 TMS, M4×8 2

94 HN05 HN, M5 2
95 HB0610 HB, M6×10 1
96 TC-094 Spacer 1
97 LA-30200 Label 1
98 LA-30210 Label 1

-24-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

1 TE-001 Inner Flange 1
2 TC-014 Outer Flange 1
3 TE-003 Shaft 1
4 TC-015 Protector 1
7 TC-016 Reel Nut Handle 1

8 TC-004 Package Guide 1
10 TE-010 Grommet 2
11 TC-006 Caster (Free) 2
12 TC-007 Caster (Brake) 2
13 TE-013 Lock Pin 4
14 TE-014 Brake Holder (R) 1
15 TC-002 Bracket 1
16 TC-008 Grommet 1
17 TE-017 Bush (L) 1
18 TE-018 Bush (R) 1
19 TC-020 Pin 1
20 TC-021 Split Pin 1
21 TJ-021 Brake Set 1
22 TE-022 Pin 1
23 TE-023 Rubber Stop 1
24 TE-024 Brake Holder (L) 1
25 TE-025 Spring 1
26 ER04 Snap Ring, E-4 2
27 TE-027 Roller Holder 1
28 TE-028 Roller 1
29 TE-029 Pin 1
30 TE-030 Band Guide Bracket 1
31 TC-049 Roller 1
32 TC-048 Shaft 1

38 TMS0508 TMS, M5×8 (Only CE) 6
39 SW16 SW, M16 4

41 TJ-001 Body Frame 1

TJ-010 Body Frame (Only CE) 1
42 TE-042 Magnet Catch 4
43 TJ-043 Side Door (L) 1

-26-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
44 TJ-044 Side Door (R) 1

46 TJ-002 Top Plate 1
47 TE-001A Reel Unit 1
48 TE-030A Band Guide Bracket Ass'y 1
49 TJ-021A Brake Arm Ass'y 1

51 HBS0612 HBS, M6×12 2
53 TMS0305 TMS, M3×5 8
54 PW06A PW, M6 (A) 2
55 HBS0620 HBS, M6×20 7
56 HB0612 HB, M6×12 4
57 SW06 SW, M6 9
58 SR10 Stop Ring, S-10 4
59 PW06C PW, M6 (C) 14
60 PW06B PW, M6 (B) 2
63 WN06 WN, M6 2
64 HN06 HN, M6 9

71 TJ-023 Bracket of Smoke-Exhaus Pipe 1
72 TJ-024 Smoke-Exhaus Pipe 1
74 TJ-092 Reel Assist Bracket 1
75 TC-075 Center Drum 280mm 1

77 TC-076 Washer 1
78 ER19 Snap Ring, E-19 1
79 TB-205 Guide 1

81 SW04 SW, M4 4
83 PW05 PW, M5 2
84 SW05 SW, M5 2
85 HN05 HN, M5 2

87 PW04 PW, M4 2
88 HN04 HN, M4 2
89 PMS0408 PMS, M4×8 4
90 TMS0408 TMS, M4×8 2
91 LA-31010 Label 1

-27-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

1 TL-001 Body Frame 1

TL-001S Body Frame (Stainless Steel Model) 1

2 TL-002 Table (L) 1

TL-002S Table (L)(Stainless Steel Model) 1

3 TD-003 Reel Shaft 1

TD-003S Reel Shaft (Stainless Steel Model) 1

4 TL-004 Table (R) 1

TL-004S Table (R)(Stainless Steel Model) 1

5 TL-005 Top Plate 1

TL-005S Top Plate (Stainless Steel Model) 1

7 TL-007 Front Plate 1

TL-007S Front Plate (Stainless Steel Model) 1

8 TC-006 Caster (Free) 2

TC-006S Caster (Free)(Stainless Steel Model) 2

9 TC-007 Caster (Brake) 2

TC-007S Caster (Brake)(Stainless Steel Model) 2
10 TC-019 Roller 2
11 TL-011 Table Support 1

TL-011S Table Support (Stainless Steel Model) 1
12 TL-012 Reel Support 1

TL-012S Reel Support (Stainless Steel Model) 1
13 TC-013 Inner Flange 1
14 TC-014 Outer Flange 1
15 TL-015 Guide 1

TL-015S Guide (Stainless Steel Model) 1
16 TD-016 Reel Nut Handle (LH) 1
17 TL-017 Back Door 1

TL-017S Back Door (Stainless Steel Model) 1
18 ER07S Snap Ring, E-7 (SUS) 16
19 T6-5-11120 Table Roller 8

T6-5-11121 Table Roller (Plastic) 8
20 T6-5-11130 Table Roller Shaft 8

T6-5-11131 Table Roller Shaft (Stainless Steel

Model)

8

21 TL-021 Brake Arm 1

TL-021S Brake Arm (Stainless Steel Model) 1

-29-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
22 TE-027 Roller Holder 1

TE-027S Roller Holder (Stainless Steel Model) 1
23 TL-023 Stopper 1
24 TL-024 Bolt 1
25 HN08 HN, M8 2

HN08S HN, M8 (Stainless Steel Model) 2
27 FMS0410 FMS, M4×10 4

FMS0410S FMS, M4×10 (Stainless Steel Model) 4

30 TL-030 Brake lining 1
31 TD-047A Roller Bracket Ass'y 1
32 TL-007A Front Plate Ass'y 1
33 T6-4-30000 Reel Control Group 1

T6-4-30000S Reel Control Group (Stainless Steel 1

Model)

34 SW16 SW, M16 4

SW16S SW, M16 (Stainless Steel Model) 4

41 TL-041 Door Lock 2
42 TL-042 Bracket 1
43 TD-047 Roller Bracket 2

TD-047S Roller Bracket (Stainless Steel Model) 2
44 TD-048 Shaft 2

TD-048S Shaft (Stainless Steel Model) 2
45 T6-2-11140 RH Strap Guide Flap Pin (Rear) 2
46 T6-2-11150 RH Strap Guide Flap Spring 2
47 TL-047 Flap 1

TL-047S Flap (Stainless Steel Model) 1

-30-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
52 SR10 Stop Ring, S-10 5

SR10S Stop Ring, S-10 (Stainless Steel Model) 5
53 HBS0816 HBS, M8×16 4

HBS0816S HBS, M8×16 (Stainless Steel Model) 4
54 SW08 SW, M8 5

SW08S SW, M8 (Stainless Steel Model) 5
55 TMS0612 TMS, M6×12 8

TMS0612S TMS, M6×12 (Stainless Steel Model) 8
56 HB0610 HB, M6×10 4

HB0610S HB, M6×10 (Stainless Steel Model) 4
57 SW06 SW, M6 6

SW06S SW, M6 (Stainless Steel Model) 6

65 TE-028 Roller 1
66 TE-029 Pin 1

TE-029S Pin (Stainless Steel Model) 1
67 ER04 Snap Ring, E-4 2

ER04S Snap Ring, E-4 (Stainless Steel Model) 2
68 LA-30200 Label 1
69 LA-30210 Label 1
70 TL-070 Supporting Leg 4

TL-070S Supporting Leg (Stainless Steel Model) 4
71 HB0616 HB, M6×16 16

HB0616S HB, M6×16 (Stainless Steel Model) 16
72 SW06 SW, M6 16

SW06S SW, M6 (Stainless Steel Model) 16
73 PW06C PW, M6 (C) 16

PW06CS PW, M6 (C)(Stainless Steel Model) 16

-31-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

5 TF-005 Safety Switch Plate (Option) 1

15 TF-015 Terminal Bracket 1
16 TF-016 Cover (Only CE) 1

18 TF-018 Safety Limit Switch (For CE)(Option) 1
19 TF-019 Adiabatic Plate 1
20 TF-020 Fan Cover 1
21 TF-021 Fan (For 110V) 1

TF-021-1 Fan (For 220V/230V/240V) 1
22 T7-5-10210 Switch Actuator (Option) 1

23A TF-023A Heater Transformer Ass'y (For 110V) 1

TF-023A-1 Heater Transformer Ass'y 1

(For 220V/230V/240V)

24 TF-024 Transformer Cover 1
25 TF-025 Knob 1

27 TF-027 Selector Switch 1
28 TG-024 Wire (For TP-201)(Option) 1

TG-025 Wire (For TP-203)(Option) 1

TG-026 Wire (For TP-201Y)(Option) 1

TG-027 Wire (For Top Plate)(Option) 1
29 TE-099 Safety Limit Switch Ass'y (Option) 1
30 TF-029 Cover (Only TP-203) 1
31 TF-031 Switch Cover (Option) 1
32 LA-40002 Label 1

-33-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS
41 TJ-022 Fan Support 1

42 T5-4-10310 Earth Plate (5P)(For CE)(Option ) 1
43 TK-035 Interlock Safety Switch 1

45 T6-6-10980 Cable Gland (PG11) 1

(For TUV CE Version)(Option)

50 TE-097 Safety Limit Switch Ass'y 2

(For TP-201CE)

TE-100 Safety Limit Switch Ass'y 2

(For TP-203CE)

TE-098 Safety Limit Switch Ass'y 2

(For TP-201Y)
51 TMS0512 TMS, M5×12 (Option ) 4
52 TMS0412 TMS, M4×12 (For CE)(Option ) 1
53 HB0620 HB, M6×20 2
54 TMS0408 TMS, M4×8 (Option ) 4
55 PMS0425 PMS, M4×25 (Option ) 4
56 PMS0520 PMS, M5×20 4
57 PMS0410 PMS, M4×10 4

PMS0410 PMS, M4×10 (For TP-201/TP-202) 8

58 FMS0508 FMS, M5×8 (For TUV CE Version) 2

(Option )
59 PMS0412 PMS, M4×12 (For TP-203)(Option) 4
60 SW04 SW, M4 (For TP-201/TP-202) 4

SW, M4 (For TP-203)(Option) 4

61 SW06 SW, M6 2
63 SW05 SW, M5 6

66 PW06C PW, M6 (C) 4
67 PW05 PW, M5 4
68 HN06 HN, M6 2
70 HN04 HN, M4 (Option) 4

-34-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

74 TMS0508 TMS, M5×8 2
75 HN05 HN, M5 4

HN, M5 (For TUV CE Version) 2

(Option )
76 PW04 PW, M4 (Option) 4

80 PMS03.515 PMS, M3.5×15 2
81 PMS0408 PMS, M4×8 2
82 PW04 PW, M4 1

-35-

REF.

NO.

PART NO. DESCRIPTION Q'TY REMARKS

1 TG-001 Power Switch 1
2 TG-002 Variable Resistor (1MΩ)2
3 TG-003 Knob 1
4 TG-004 Reset Push Button Switch 1
5 TG-005 Feed Push Button Switch 1
6 TG-006 Control Panel 1
7 T2-6-30250 PC Board 1
8 TG-008 PC Board Receptacle 1

9 TG-009 Base 1
12 TG-012 Knob 1
13 TG-013 Fuse Holder 1
14 T6-6-30133 Fuse (10A)(For 110V AC) 1

T6-6-30034 Fuse (7A)(For220V/230V/240V AC) 1

15 TG-015 Transformer (For 110V) 1

TG-015-1 Transformer (For 220V) 1

TG-015-2 Transformer (For 240V) 1
16 TG-016 Bolt 1
19 TG-019 Power Cord 1
20 LA-10018 Label 1
21 TG-021 Switch Cover 1
22 TG-022 Grommet 1
23 LA-40001 Label 1
24 LA-40003 Label 1

30 LA-20170 Label 1
34 TG-034 Cover 1

51 TMS0408 TMS, M4×8 8
52 HN04 HN, M4 2
53 TMS0312 TMS, M3×12 2
61 TK-001 Main Power Switch (Only CE) 1
62 PW04 PW, M4 2
63 PMS0408 PMS, M4×8 2
64 SW03 SW, M3 2

05/2010

-37-