Trans Pac TPH-5500-12/24HS, TPH-5500-012/HF, TPH-5500-12/24HD, TPH-5500-012/F, TPH-5500-024/F User Manual

I. Introduction

The TPH-5500 series Camera Housing is constructed from die-cast aluminum alloy with powder coated finish and is

equipped with an adjustable Fully-Cable-Managed Mounting Bracket. The product is CE certified and has environmental

protection level IP 68 or IP 44 with blower, Reach and RoHS compliance.

II. Mounting Configuration and Dimensions of TPH 5500

User’s Manual

Model No: TPH-5500 Series

Adjust position and direction

III. Fitting instructions for camera.

Inside the internal wiring diagram of TPH 5500 for the
window demister. A spare 6 way terminal block is

provided at the rear of the housing for the camera when

necessary and lens connections. Circuit identified as
follows:

IV. Wiring Diagram

TB.1 6 way terminal block
TB.2 3 way terminal block
FTB.1 Fused terminal block
STAT.1 18℃ Thermostat
STAT.2 35℃ Thermostat
H.1 Heater
PSU Power Supply Unit
P.C.B.1 Thermal control circuit board
FS.1 3 Amp. Fuse

BR-13 Fully-Cable Managed Bracket

Inner space for camera mount
W60 x H80 x L260mm

Dimensions of Bracket Base

Power supply unit (option)

Camera mounting platform

Heater shield

Heater

Thermal control board

Cable conducts

Terminal block assembly

Blower

Ground wire

!

V. INSTALLATION SUGGESTION:

If you plan to install this camera into a tropical, sear coastal, saltwater or corrosive industrial water/moist environment,

please seal each stainless steel screw and fittings with a silicon grease compounds. This will help prevent electrolysis
corrosive occurring and extend the lifespan of the camera and housing. The installation of a surge protection device is
strongly recommended in frequent thunder area.

1. Pin1,2 and pin 3,4 is DC 12V output for motor lens, IR illuminator,
siren or speaker use. If no use please remove cable from connector.

2. Pin 5,6 is for DC12V output for camera.

DC output of PSU connectors AC power connection

Shows how to connect the AC power cord to
the FTB. 1 connector.

IMPORTANT NOTE:

1. Disconnect Device: A disconnect device from main supply shall be incorporated in the building installation wiring.

2. Electrical Connections: Only a qualified electrician allow to make electrical connections.

Trans Pacific Industries Corp.

5F, No.79 Jen-Ai Road Section 4, Taipei 106, Taiwan
Tel: [phone] Fax: [phone]

http://www.transpac-cctv.com

Features

1. Turn on at 35°C 1. 880 (80-260Vac input, 1x12Vdc output, 1A)

2. Turn off at 25°C 2. 080 (80-260Vac input, 4x12Vdc output, 3.5A)

3. 324 (24Vac input, 4x12Vdc output, 3.5A)

Model No. 4. 424 (24Vac input, 1x12Vdc output, 1.5A)

12Vdc / 24Vac

110 / 230Vac

12Vdc / 24Vac

110 / 230Vac 12Vdc 24Vac 880 080 324 424
5500
5500-12/24HS

●

5500-12/24HD

●

5500-012/F

●

5500-012/HF

● ●

5500-024/F

●

5500-024/HF

● ●

5500-110/230HS

●

5500-110/230HD

●

5500-080/HS

● ●

5500-080/HD

● ●

5500-080/F

● ●

5500-080/HF

● ● ●

5500-080/HC**

●

●

5500-324/F

● ●

5500-324/HF

● ● ●

5500-324/HC**

● ●

5500-880/F

● ●

5500-880/HF

● ● ●

5500-880/HC**

●

●

5500-424/F

●

●

5500-424/HF

●

●

●

5500-424/HC**

●

●

*First heater prevents moisture on the window glass till weather temperature -25°, second heater is heating in enclosure for camera operation properly till

weather temperature -40°
** With 12Vdc camera jet

PSU (power supply unit)

Turn off at 28°C

2. Turn off at 28°C

Blower (IP44)

Double heaters*

1. Turn on at 18°C

Single heater

1. Turn on at 18°C

2. Turn on at 0°C

Turn off at 10°C

●