Page 1
: DOOR ENTRY UNIT
Programming Software
MODELS: EIS-1, EIS-2 OR EIS-4
USER MANUAL
v.02 2018
Page 2
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%1%
Contents
1! FOR YOUR SAFETY ..............................................................................................................................................4!
2! INTRODUCTION ....................................................................................................................................................5!
3! EIS-1, EIS-2, EIS-4 FEATURES AND APPLICATIONS ...................................................................................6!
4! START UP ................................................................................................................................................................7!
5! LED INDICATION..................................................................................................................................................8!
6! CONNECTION DIAGRAM ...................................................................................................................................9!
7! EIS UNIT MANAGEMENT .................................................................................................................................10!
8! EIS FUNCTIONS WITH PROGRAMMING INSTRUCTIONS...................................................................... 11!
8.1! WEB SERVER - LOG IN ................................................................................................................................................... 11!
8.2! WEB SERVER – ADDING UNITS TO USER PROFILE................................................................................................. 12!
8.3! WEB SERVER-UNIT MANAGEMENT........................................................................................................................... 14!
8.4! INTERCOM CONFIGURATION ...................................................................................................................................... 15!
8.5! KEYPAD PIN ENTRY – ACCESS.................................................................................................................................... 17!
8.6! WIEGAND ACCESS.......................................................................................................................................................... 19!
8.7! CALLER ID ACCESS ........................................................................................................................................................ 21!
8.8! OUTPUTS SETTINGS ....................................................................................................................................................... 22!
8.9! EIS WIEGAND OUTPUT INTEGRATION ...................................................................................................................... 24!
8.10! TIMER-TIMED CONTROLED OUTPUT......................................................................................................................... 25!
8.11! ADMINISTRATION .......................................................................................................................................................... 27!
8.12! EVENT LOGING................................................................................................................................................................ 29!
8.13! MISCELLANEOUS............................................................................................................................................................ 30!
8.14! PIN ACCESS NOTIFICATION FUNCTION .................................................................................................................... 31!
9! WIEGAND INPUT DATA FORMATS ............................................................................................................... 33!
9.1! WIEGAND 26 BIT, DIFFERENT DATA FORMATS ...................................................................................................... 35!
9.2! WIEGAND 30 BIT, DIFFERENT DATA FORMATS ...................................................................................................... 36!
Page 3
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%2%
Figures
Figure 1: EIS: Connection diagram .....................................................................................................9!
Figure 2: WEB Server-Sign In page .................................................................................................. 11!
Figure 3: WEB Server-Main page select ADD mode........................................................................12!
Figure 4: WEB Server-Main page adding EIS units..........................................................................13!
Figure 5: WEB Server-Unit management window ............................................................................ 14!
Figure 6: WEB Server-Intercom settings...........................................................................................15!
Figure 7: WEB Server-Keypad PIN Access: Permanent PIN codes .................................................17!
Figure 8: WEB Server-Adding Wiegand devices with temporary use. .............................................18!
Figure 9: WEB Server-First Wiegand interface support.................................................................... 19!
Figure 10: WEB Server-Wiegand interface support. ......................................................................... 20!
Figure 11: WEB Server-Adding Wiegand devices with permanent use.Error! Bookmark not
defined.!
Figure 12: WEB Server-Adding Wiegand devices with temporary use.Error! Bookmark not
defined.!
Figure 13: WEB Server-Caller ID Access .........................................................................................21!
Figure 14: WEB Server-Output setting.............................................................................................. 22!
Figure 15: WEB Server-Wiegand Output settings............................................................................. 24!
Figure 16: WEB Server-Timer setting →Day mode. ........................................................................25!
Figure 17: WEB Server-Timer setting →Week mode.......................................................................25!
Figure 18: WEB Server-Notification numbers ..................................................................................27!
Figure 19: WEB Server-Input alarm configuration ...........................................................................27!
Figure 20: WEB Server-Log event ....................................................................................................29!
Figure 21: WEB Server-Misc ............................................................................................................30!
Figure 22: WEB Server-Global enabling of the notificaton function................................................ 31!
Figure 23: WEB Server-Selecting administrator numbers for notification. ......................................32!
Figure 24: WEB Server-First Wiegand interface support.................................................................. 33!
Figure 25: WEB Server-Second Wiegand interface support. ............................................................ 34!
Page 4
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%3%
Tables
Table 1: WEB Server-SPIN entry parameters. ..................................................................................18!
Table 2: WEB Server-SPIN entry parameters. ..................................Error! Bookmark not defined.!
Table 3: WEB Server-Timer setting, output mode options ...............................................................26!
Table 4: Wiegand 26: Mode 0............................................................................................................35!
Table 5: Wiegand 26: Mode 1............................................................................................................35!
Table 6: Wiegand 26: Mode 2............................................................................................................35!
Table 7: Wiegand 26: Mode 3............................................................................................................35!
Table 8: Wiegand 30: Mode 0............................................................................................................36!
Table 9: Wiegand 30: Mode 1............................................................................................................36!
Table 10: Wiegand 30: Mode 2..........................................................................................................36!
Table 11: Wiegand 30: Mode 3..........................................................................................................36!
Page 5
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%4%
1 FOR YOUR SAFETY
SWITCH ON SAFELY
Do not switch the unit on when use of wireless phone is prohibited or when it may cause
interference or danger.
INTERFERENCE
All wireless phones and units may be susceptible to interference, which could affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the unit off near medical equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in aircraft.
SWITCH OFF WHEN REFUELING
Do not use the unit at a refueling point. Do not use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the unit where blasting is in progress.
USE SENSIBLY
Use only in the normal position as explained in the product documentation. Do not touch the
antenna unnecessarily.
Page 6
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%5%
2 INTRODUCTION
EIS-1, EIS-2, EIS-4 (EIS) is a simple but powerful GSM intercom communication system designed
to ensure low-cost, simple to install/use, reliable and single box solution for intercom application. It
is designed for unlimited range, wire free GSM intercom, pin code access, caller ID control and
Wiegand access support.
Optional EIS supports alarm detection, stay-alive messages, credit detection etc.
Page 7
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%6%
3 EIS-1, EIS-2, EIS-4 FEATURES and APPLICATIONS
Features:
⇒ Built-in 5 band GSM module
⇒ Up-to 4 intercom call button support (5 numbers each)
⇒ Keypad Access entry support (up-to 1000 PIN codes)
⇒ Caller ID numbers control (up-to 1000 caller ID numbers)
⇒ Up to 100 temporary SPIN access codes
⇒ Input Wiegand receiver(up-to 1000 receivers)
⇒ 2 outputs (relay supported)
⇒ Programming with PC via “USB to Mini USB cable” connected to the unit
⇒ Programming by WEB server
⇒ Programming by SMS commands
Applications:
⇒ Single box, wire free intercom solution
⇒ Remote gate opener – Caller ID number recognition
⇒ Simple (Wiegand) access system
Page 8
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%7%
4 START UP
EIS unit accepts a standard GSM Sim (T-Mobile or AT&T) card.
VERY
IMPORTANT
USE A MICRO SIM CARD
WARNING
DO NOT Insert or remove the SIM card while the unit is powered ON!!
IMPORTANT
Before inserting SIM card to unit make sure the PIN code is
removed!!
⇒ Insert SIM card in EIS unit.
⇒ Connect power cable to EIS unit (YOU MUST POWER THE EIS UNIT WITH THE
POWER SUPPLY INCLUDED). Do not power with any other power supply.
⇒ Power up the unit.
⇒ Wait until LED1 (Blue) starts flashing. This is set in around 30 – 45 seconds.
⇒ EIS unit is now ready to operate.
NOTE
EIS device will “beep” in 15s intervals until the unit reaches normal operation.
Page 9
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%8%
5 LED INDICATION
Blue LED (LED1)
- Indicates the level of the GSM signal from 1 to 5 LED flashes (1 is weak signal, 5 is
excellent signal)
Red LED (LED2)
- GSM module Activity
Yellow LED (LED3)
- Short flashing indicates that the GSM module is ON, but it is not yet connected on the GSM
network. After connection, yellow led is flashing with short pulse (1/2 s) ON and a long
pulse OFF (5s).
Page 10
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%9%
6 CONNECTION DIAGRAM
Before connection the EIS please take a look at connection diagram.
Figure 1: EIS: Connection diagram
********************************************************************************
********************************************************************************
IMPORTANT
DO NOT USE Power out (12V AUX) for electric lock driving! Use
separate power source for door electric lock!
Page 11
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%10%
7 EIS UNIT MANAGEMENT
Unit supports different types of management (programming):
********************************************************************************
⇒ Unit can be programmed remotely by using WEB server access.
Access it by EISWARE.com
⇒ EISWARE APP on IPHONE or ANDROID
Must have data plan enabled to get data transfer on either method.
********************************************************************************
These are alternative solutions to accomplish the programming.
⇒ Unit can be programmed remotely by SMS commands (Optional).
⇒ Unit can be programmed directly by USB connection, with the use of configuration software
running on PC (EIS Ware).
Page 12
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%11%
8 EIS FUNCTIONs with PROGRAMMING
INSTRUCTIONs
As mentioned in previous chapters EIS unit can be programmed in various way, this document will
focus on most common programming way: WEB programming.
IMPORTANT
SIM card in the EIS unit MUST have DATA PLAN to be able to use WEB
programming!
8.1 WEB SERVER - LOG IN
The web server can be find under the address: https://www.eisware.com/.
Figure 2: WEB Server-Sign In page
User must first use the Sign IN section to create working profile on the server. The profile can be
created by using social login like Facebook, Google account or Twitter. If user lacks any of the
social profile it can proceed to Sign UP page use standard user name and password entry.
NOTE
Server support Firefox, Google Chrome and Safari.
Page 13
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%12%
8.2 WEB SERVER – ADDING UNITS TO USER PROFILE
After login the user will be diverted to WEB server main window. This page is used to
add/remove/search for EIS units from the user’s profile.
Select “+” sign to select ADD EIS units to user’s profile.
Figure 3: WEB Server-Main page select ADD mode
Page 14
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%13%
Figure 4: WEB Server-Main page adding EIS units
User than provides required data:
• Name: Name for the added unit - mandatory information.
• IMEI: Identification number of the unit, can be found in the enclosure of the unit -
mandatory information. The IMEI is located on the cellular chip and also should be on the
card board box of the EIS.
• Phone Number: The telephone number of the SIM card in the EIS unit - mandatory data.
• GPRS settings: Information needed to enable data connection between the server and the
unit. Selectable from the drop-down menu - mandatory data.
• Location: Notification field, used by the user to provide extra data for its own information -
optional data.
By clicking the “+” (insert sign) after filling mandatory data, the unit will be added to the user
profile.
First building of the unit data-base may take a few minutes.
Page 15
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%14%
8.3 WEB SERVER-UNIT MANAGEMENT
After the EIS unit is added to user database, the user can change the configuration of the specific
unit.
All changes made by the user are listed in the Change Log window. By clicking Send to device
button ALL changes are send to the unit. User can (Revert) all changes made, before sending, by
clicking (Revert all) or select particular entry and revert it.
Figure 5: WEB Server-Unit management window
Page 16
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%15%
8.4 INTERCOM CONFIGURATION
Primary function of the EIS unit is intercom support. Selecting (calling) apartment number is
achieved pressing the call button beside appropriate name plate.
This actions will start a voice call procedure from Phone number 1 till Phone number 5. After the
call is answered the called user has the option to trigger the output by pressing “11” for opening
Output 1 or “21” for triggering Output 2.
If the call is answered the unit will stop dialing next numbers on the list.
** To terminate the call press any button.
Management of the intercom function is found under Intercom tab.
Figure 6: WEB Server-Intercom settings.
Intercom management parameters:
• Telephone number 1…Telephone number 5: Number that the unit will call when call
button pressed.
• Delay before dialing next no. on the list: Time delay in second before next user on the list
gets dialed if the call to the previous user is not answered.
• Extension number: Parameter is used to set the DTMF number in auto self-select function
• Extension no. delay: Parameter is used to set the delay (in sec.) for sending DTMF number
in auto self-select function.
Page 17
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%16%
• Work time start, Work time end: Parameters are used to define work time schedule.
Inside this limits number under position 1 to 4 will be dialed, outside this limits number
under position 5 will be dialed.
Voice call setting
• Microphone level: Increasing the level will increase the sensitivity of the unit microphone
decreasing will decrease the sensitivity.
• Speaker level: Increasing the level will increase the volume of the unit speaker, decreasing
will decrease the level of the speaker.
• Ringing sound: By selecting Playing the unit will play the dial tone in the connection phase
of the call, by selecting Muted the unit will not play any sound in the connection phase of
the call.
• On activate input: By selecting Play beep sound (buzzer) the unit will provide audio feed
back (buzzer BEEP) when the apartment entry is selected, by selected Muted unit will
provide no audio feedback when the apartment entry is selected.
NOTE
EIS-1 has 1 CALL button.
EIS-2 has 2 CALL buttons.
EIS-4 has 4 CALL buttons.
Page 18
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%17%
8.5 KEYPAD PIN ENTRY – ACCESS
Secondary use of on-board keypad is access by entering PIN codes. Pin codes must be at least 4
digits.
Pin codes can be defined in two sections. First section is permanent pin code and second is
temporary pin codes which are limited by the consecutive time they are entered.
Permanent pin codes are placed in Pin access tab.
They are placed in two tables. For each table user can define which output they will trigger.
Figure 7: WEB Server-Keypad PIN Access: Permanent PIN codes
PIN entry: For each PIN entry user need to select PIN code value and optional User name.
Temporary pin codes are placed in Temporary pin access tab.
Page 19
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%18%
Figure 8: WEB Server-Adding Wiegand devices with temporary use.
• Temp PIN codes activate output: Selecting the output that will be triggered in case of
correct SPIN code.
• SPIN entry: For each SPIN entry user need to select appropriate values.
SPIN options
Description
SPIN value
Temporary PIN code
User name
Name of the user
Notify
If SPIN code is used, administrator numbers CAN be notified
Counter limit
Enable/Disable counter limitation (consecutive use)
Timer limit
Enable/Disable timer limitation
Timer mode
Timer limit mode: Day limit (day limitation), Timer limit
(hours of a day access limitation)
Rules valid on weekend
Enable/Disable timer limitation for weekend days
Counter
Number of allowed use of SPIN code
Timer start/Timer end
Bottom and Top timer limitation
Table 1: WEB Server-SPIN entry parameters.
Page 20
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%19%
8.6 WIEGAND ACCESS
EIS unit has onboard support for 2 Wiegand output based device. With the use of external replicator
more Wiegand devices can be connected to the unit.
Configuration of first Wiegand interface is found in Digital interface tab. First Wiegand interface
can be found on board with a dedicated Wiegand connector and cables.
Figure 9: WEB Server-First Wiegand interface support.
• Mode: Select appropriate data formatting (Advise unit provider for more info if needed,
mode 2 is most common setting)
• Facility code: User can Enable or Disable facility code field.
NOTE
See Chapter 9-WIEGAND INPUT DATA FORMATs for detailed explanation
of different data format options.
Second Wiegand interface is shared with alarm input lines, user must select Wiegand in Input
operation mode found in the Inputs tab.
Page 21
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%20%
Additional settings for Wiegand interface input are found in Wiegand input 2 configuration
section.
Figure 10: WEB Server-Wiegand interface support.
• Mode: Select appropriate data formatting (Advise unit provider for more info if needed,
mode 2 is most common setting)
• Facility code: User can Enable or Disable facility code field.
Wiegand devices can be defined in two section. First section is permanent pin codes and second is
temporary pin codes - limited by the number of use.
NOTE
See Chapter 9-WIEGAND INPUT DATA FORMATs for detailed explanation
of different data format options.
IMPORTANT
Unit MUST be restarted when switching between Normal and Wiegand mode
in the Input operation mode.
Page 22
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%21%
8.7 CALLER ID ACCESS
Caller ID access is a very simple way to control relay output defined in Caller ID output setting.
User will by calling in the EIS unit trigger defined output.
Settings for this function are found in the Caller id # tab.
Figure 11: WEB Server-Caller ID Access
General settings:
• Caller ID security mode: User can select between 3 options:
Caller ID Disabled deactivates caller ID function – all numbers are restricted
Caller ID for specific users will limit the caller ID function only to the numbers on the list.
Caller ID always ON will allow all user that know the number of the unit to open defined
output. In last option the user doesn’t need to be on the list to trigger the output
• Caller ID output: Selecting the output that will be triggered in Caller ID function.
NOTE
Selection Caller ID always ON will allow anybody with the knowledge of the
unit number to trigger the output by calling the unit. Use this setting with
caution.
Page 23
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%22%
8.8 OUTPUTS SETTINGS
The behavior on the outputs is defined in the Output tab.
Figure 12: WEB Server-Output setting
Output 1 - Settings for output 1:
• Output (relay) mode: User can select between 3 options
Disable-Output is disabled.
Latching-Output is in latching mode. First Caller ID or PIN entry will activate the output,
second Caller ID or PIN entry will deactivate the output.
Time Pulse-Output is time pulse mode. After output is triggered it will be activated for the
time defined in Output pulse duration, after that time output will be restored.
• Output pulse duration: ON time for output in case of output mode Timer pulse.
• Output is: Output can work in normal or inverted (normally close) mode.
Normally open-In idle mode output pins are in open position.
Normally closed-In idle mode output connections are closed.
Page 24
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%23%
Output 2 - Settings for output 2:
• Output (relay) mode: User can select between 3 options
Disable-Output is disabled
Latching-Output is in latching mode. First Caller ID or PIN entry will activate the output,
second Caller ID or PIN entry will deactivate the output.
Time Pulse-Output is time pulse mode. After output is triggered it will be activated for the
time defined in Output pulse duration, after that time output will be restored.
• Output pulse duration: ON time for output in case of output mode Timer pulse.
• Output is: Output can work in normal or inverted (normally close) mode.
Normally open-In idle mode output pins are in open position.
Normally closed-In idle mode output connections are closed.
Additional output settings - Setting are used to link onboard actions with the outputs if needed:
• Voice active indication: When unit reaches voice connection (intercom call) output
defined under this section gets activated.
• Unauthorized call or SMS received: If unauthorized call or SMS is received on the unit
this event will activate output defined under this section.
• Button pressed indication: When intercom call button is pressed output defined under this
section gets activated.
• Input 1 activate output: If input 1 is in alarm mode (Input operation mode: Normal mode
selected) alarm input event on the input will activate output defined under this section.
• Input 2 activate output: If input 2 is in alarm mode (Input operation mode: Normal mode
selected) alarm input event on the input will activate output defined under this section.
NOTE
Do to limitation of the outputs use additional outputs settings with care.
Page 25
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%24%
8.9 EIS WIEGAND OUTPUT INTEGRATION
EIS unit can be integrated into a bigger access system using a Wiegand interface. In this case
number’s calling the EIS unit will be transferred, over Wiegand interface, to access system.
Figure 13: WEB Server-Wiegand Output settings.
Configuration of the Wiegand output interface
• Wiegand Type: Type of the Wiegand used (W26 is most common setting)
• Data format: Format of data set on the selected Wiegand type.
• Front parity, trailing parity: Selection of the proper parity in selected Wiegand type.
• Facility code: Is required, user can define facility code to Wiegand data.
NOTE
See Chapter 9-WIEGAND INPUT DATA FORMATs for detailed explanation
of different data format options.
Page 26
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%25%
8.10 TIMER-TIMED CONTROLED OUTPUT
EIS unit features 2 timers that can be used to control the outputs on the unit. Timers can run in day
or week mode depending on the selected setting. For each timer user can select which output it will
control.
Figure 14: WEB Server-Timer setting →Day mode.
Figure 15: WEB Server-Timer setting →Week mode.
Page 27
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%26%
Timer settings:
• Timer: Parameter is used to enable and disable the timer function.
• Mode: User can select between day or week mode. In day mode the timer will control on
the day table which is the same for all week. In week mode the user can define different
setting for each day in the week.
• Timer controls: Output controlled by the timer function.
Output 1 or Output 2
• Output mode: Output mode management definition.
OUTPUT mode options
Description
Slave mode
The behavior of the outputs (Time pulse or Latching mode) is
defined in the Output tab.
Master mode:
When the output is driven by the timer (output is activated by
the timer) the outputs are in latching mode regardless of the
setting in Output tab. When the output is not activated by the
timer, the outputs are working by the defined settings in
Output tab.
Output precondition
In this mode Timer is used as PRECONDITION for output
control used by other functions like PIN access or Called ID
#.
Table 2: WEB Server-Timer setting, output mode options
• Holidays: With the definition of the holiday days (use day picker), user can define special
behavior on the holiday days.
The described settings are the same for both timers.
Page 28
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%27%
8.11 ADMINISTRATION
Administration tab allows user to enable advanced settings: notification of unauthorized access,
periodic test messages, lock down of the unit…
Figure 16: WEB Server-Notification numbers
• Phone number, User name: Phone number and user name of the user that will be receiving
notification messages.
• Input1, Input2: If input lines 1 & 2 are defined in alarm mode (Input operation mode:
Normal mode) and if alarm condition is meet, users with check boxes will receive alarm
notification SMS.
Figure 17: WEB Server-Input alarm configuration
• Periodic test: User can receive periodic (keep-alive) SMS, tick the check box for the
appropriate user. Timer period is defined under parameter Automatic periodic test SMS, it
is definable in hours.
Page 29
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%28%
• Low credit alert: In case of prepaid SIM card the unit can notify the user if the credit on the
SIM card is low. To enable notification SMS tick the check box in corresponding position.
Note that additional input in the Misc. tab is needed to fully enable credit checking function.
• Unauthorized call: In case of unauthorized call the unit can notify user. To enable
notification SMS tick the check box in corresponding position.
• Log full: Administrator can receive a SMS when LOG event buffer gets at a critical full
level.
• Notify event: Selection of administrators that will be notified if the notification event is
enabled in Temporary pin access tab or Pin access tab.
• Administration allowed to remote program by SMS: By selection this option the user
can “Lock down” the EIS unit, preventing any unauthorized user to change any
configuration on the unit.
• Automatic call to administrator 1: To prevent SIM card provider to lock out the SIM card
from the network, user can define a periodic call out to telephone number under position 1.
Parameter is defined in days (It is not mandatory to set this parameter).
• Automatic periodic test SMS: Definition of Time Out for periodic SMS sending.
• Test SMS start hour: Periodic SMS, first send-out hour.
Page 30
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%29%
8.12 EVENT LOGING
EIS unit itself support a 20000 log events entry. These log events can be pull up to the server by
clicking Read Log button in the “Event Log” tab. Events are listed in the table.
Figure 18: WEB Server-Log event
Each event is equipped with the event type, time, output if triggered and the user name of the user
responsible for the event.
If user names are available (Called ID #, PIN codes, Intercom user …) user name will be shown in
the user column.
• Automatic log clearing: Behavior if the internal LOG buffer on the unit is FULL of
events, unit can CLEAR events or STOP recording new events.
• Event logging: User can select between, not logging, logging to internal memory (unit) or
optional sending events over units USB connection to the external PC.
• Automatic log retrieval: Definition of Time Out period for unit to upload LOG events to
the WEB server.
• Caller ID logging: Enable/Disable logging of the Caller ID # events.
• System logging: Enable/Disable logging of special system evens.
• Alarm input logging: Enable/Disable logging for input alarm events.
• Pin access logging: Enable/Disable of the Pin access and Temporary pin access events.
• Output events logging: Enable/Disable of the events triggering the outputs (Timer,
Intercom etc..)
NOTE
After events are read and stored to the server, the local copy on the unit gets
deleted.
Page 31
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%30%
8.13 MISCELLANEOUS
This tab is split into 2 sections.
Figure 19: WEB Server-Misc.
General settings can be found:
• SMS text Language: define the language of the SMS information send out. User can select
appropriate language in drop-down menu.
• Automatic GSM module restart interval: User can select GSM module restart interval
(hours) if needed (Not advisable to use this parameter if not advised otherwise).
• Self-updating clock: Parameter is used to allow unit to synchronize to real time. To have
the correct time along in log event it is advisable to enable this function.
Prepaid SIM card setting is used the enable credit checking/parsing in case if prepaid SIM card is
used. User can select the proper setting by selecting used SIM card provider in the drop down menu
in Provider preset.
Page 32
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%31%
8.14 PIN ACCESS NOTIFICATION FUNCTION
This function is used to notify administrator when a selected pin code is being used. Notification is
done by SMS send to the selected administrator numbers.
Global enabling of the notification function is done in 2. Steps.
STEP 1: User has to select Enable option in the Enable Pin Notification function.
STEP 2: Send the configuration to the device!!
This procedure is ONLY done 1 time when enabling this function.
Figure 20: WEB Server-Global enabling of the notification function.
After the notification function is enabled, user can select which pin code will send the notification
SMS. This is done by placing a tick in the check box of the pin code notify field.
Page 33
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%32%
The last step is selecting a number that will be receiving the notification SMS. Selecting is done in
the Administration tab. In the Notify PIN column put a tick in the check box for the appropriate
phone number, multiple choices are possible.
Figure 21: WEB Server-Selecting administrator numbers for notification.
Page 34
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%33%
9 WIEGAND INPUT DATA FORMATs
EIS units support standard Wiegand interface, it will work with Wiegand 26bit and Wiegand 30bit
protocol. On each Wiegand protocol EIS unit support 4 different data formats, they all can be
selected through all possible management systems.
Selecting the appropriate data format for FIRST Wiegand interface is done by connecting the WEB
server, selecting the Digital interface and in Input section selecting proper Mode option.
Figure 22: WEB Server-First Wiegand interface support.
Selecting the appropriate data format for SECOND Wiegand interface is done by connecting to the
WEB server, selecting the Input tab and in Wiegand input 2 configuration section selecting
proper Mode option.
Page 35
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%34%
Figure 23: WEB Server-Second Wiegand interface support.
Page 36
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%35%
9.1 WIEGAND 26 BIT, DIFFERENT DATA FORMATS
Possible data format:
Mode 0: All 24bit of data are used a decimal representation, no option for facility code
P B B B B B B B B B B B B B B B B B B B B B B B B
P
Parity
24Bit card number
Parity
Limits
Card Number
0 - 16777215
Facility Number
None
Table 3: Wiegand 26: Mode 0.
Mode 1: 24bit of data is divided between facility code 8 bits and 16bits for card number
P F F F F F F F F B B B B B B B B B B B B B B B B
P
Parity
8Bit card facility number
16Bit card number
Parity
Limits
Card Number
0 - 16777215
Facility Number
NOT USED
Table 4: Wiegand 26: Mode 1.
Mode 2: 24bit of data is divided between facility code 8 bits and 16bits for card number
P F F F F F F F F B B B B B B B B B B B B B B B B
P
Parity
8Bit card facility number
16Bit card number
Parity
Limits
Card Number
0 - 16777215
Facility Number
0 - 255
Table 5: Wiegand 26: Mode 2.
Mode 3: Sections of 4bit data are used as decimals values for number
P B B B B B B B B B B B B B B B B B B B B B B B B
P
Parity
Dec. 6
Dec. 5
Dec. 4
Dec. 3
Dec. 2
Dec. 1
Parity
Limits
Card Number
0 - 99999
Facility Number
None
Table 6: Wiegand 26: Mode 3.
Page 37
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%36%
9.2 WIEGAND 30 BIT, DIFFERENT DATA FORMATS
Possible data format:
Mode 0: All 30bit of data are used a decimal representation, no option for facility code
P B B B B B B B B B B B B B B B B B B B B B B B B B B B B
P
Parity
28Bit card number
Parity
Limits
Card Number
0 - 268435455
Facility Number
None
Table 7: Wiegand 30: Mode 0.
Mode 1: 30bit of data is divided between facility code 8 bits, 16bits for card number and 4bits of
unused data.
P 0 0 0 0 F F F F F F F F B B B B B B B B B B B B B B B B
P
Parity
Not used
8Bit facility number
16Bit card number
Parity
Limits
Card Number
0 - 16777215
Facility Number
NOT USED
Table 8: Wiegand 30: Mode 1.
Mode 2: 28bit of data is divided between facility code 8 bits, 16bits for card number and 4bits of
unused data.
P 0 0 0 0 F F F F F F F F B B B B B B B B B B B B B B B B
P
Parity
Not used
8Bit facility number
16Bit card number
Parity
Limits
Card Number
0 - 16777215
Facility Number
0 - 255
Table 9: Wiegand 30: Mode 2.
Mode 3: Sections of 4bit data are used as decimals values for number
P 0 0 0 0 B B B B B B B B B B B B B B B B B B B B B B B B
P
Parity
Not Used
Dec. 6
Dec. 5
Dec. 4
Dec. 3
Dec. 2
Dec. 1
Parity
Limits
Card Number
0 - 99999
Facility Number
None
Table 10: Wiegand 30: Mode 3.
Page 38
EIS-1,'EIS-2,'EIS-4'
USER'MANUAL!
Page%37%
Loading...