Page 1
Multi-Media Repeater
(TR-MMR-2)
7363.C
T oken Ring 2-Port
For assistance in installing, using, or
maintaining the TRANSITION Networks
Token Ring Multi-Media Repeater,
contact TRANSITION Networks
Technical Support at:
(800) 260-1312
or contact your local distributor.
Token Ring Multi-Media Repeater
Technical Specifications
Standards
IEEE 802.5
Physical Dimensions
1.7” x10.2“ x 9.3” (42 mm x 259 mm x 235 mm)
Input Power
Universal Power Supply
Input Range: 85 to 265 VAC at 47 to 63 Hz.
(Rated at 40 watts maximum.)
MTBF:
135,000 hours
Environment
Temperature: 0-50°C (32° to 122° F )
Humidity 10-90%, non condensing
Altitude 0-10,000 feet
Warranty
5 years
25
Page 2
Token Ring 2-Port Multi-Media Repeater
24
CAUTION: RJ connectors are NOT INTENDED FOR
CONNECTION TO THE PUBLIC TELEPHONE
NETWORK. Failure to observe this caution could result
in damage to the public telephone network.
Compliance Information
UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
FCC Regulations
This equipment has been tested and found to comply with the limits for a class
A digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user
will be required to correct the interference at the user’s own expense.
Canadian Regulations
This digital apparatus does not exceed the Class A limits for radio noise for
digital apparatus set out on the radio interference regulations of the Canadian
Department of Communications.
European Regulations
Warning
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Copyright Restrictions
© 1996 TRANSITION Networks Inc.
All rights reserved. No part of this work may be reproduced or used in any
form or by any means – graphic, electronic, or mechanical – without written
permission from TRANSITION Networks Inc.
Trademark Notice
All registered trademarks and trademarks are the property of their respective
owners.
Der Anschluss dieses Gerätes an ein öffentlickes
Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die
jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie
91/263/EWG zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.
IBM Type 1 Cable and Connector Specifications
Cable Characteristics:
Type 1 cable consists of two twisted pairs in a foil braid shield.
Gauge 22 AWG
Differential Characteristic Impedance 150 Ω
Cable Type IBM PN or equivalent
Type 1 Plenum 4716748
Type 1 PVC 4716749
Connector Characteristics:
Data Connectors (IBM PN 8310574 or equivalent) can be connected to IBM
Type 1 cable.
Twisted Pair Cable and Connector Specifications
The physical characteristics of the twisted pair cable must meet or exceed the
following:
Cable Characteristics:
Category 3 wire or better is required; category 5 wire is recommended. Either
shielded twisted pair (STP) or unshielded twisted pair (UTP) can be used.
Gauge 26 to 22 AWG
Attenuation Less than 11.5 dB @ 5-10 MHz
Differential Characteristic Impedance 85 -110 Ω @ 10 MHz
DO NOT USE FLAT OR “SILVER SATIN” WIRE.
Connector Characteristics:
10BaseT twisted pair connection requires two active pairs minimum. Use only
dedicated wire pairs (such as blue/white & white/blue, orange/white &
white/orange) for the active pins.
In the Token Ring
network, twisted
pair cable must be
configured as
straight through.
Page 3
Table of Contents
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1
The Token Ring Multi-Media Repeater . . . . . . . . . . . . . . . . .1
Networking the Token Ring Multi-Media Repeater . . . . . . . .2
Connectors, Switches, and Status Indicators . . . . . . . . . . . . .3
2 SITE CONSIDERATIONS. . . . . . . . . . . . . . . . . . . . 5
Twisted Pair Network Speed Considerations . . . . . . . . . . . . .6
Token Ring RJ-45 Twisted Pair Configuration . . . . . . . . . . . .7
3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Unpacking the Multi-Media Repeater . . . . . . . . . . . . . . . . . .8
Installing Multi-Media Repeater on Flat Surface . . . . . . . . . . .9
Installing Slide-In Cards (SICs) . . . . . . . . . . . . . . . . . . . . . . .10
Connecting Cable to SIC Connectors . . . . . . . . . . . . . . . . . .11
Data Connector Connection . . . . . . . . . . . . . . . . . . . . . . . . . .11
Fiber Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
RJ-45 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Setting Configuration Switches . . . . . . . . . . . . . . . . . . . . . .17
Powering the Multi-Media Repeater . . . . . . . . . . . . . . . . . .18
4 OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Monitoring Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Monitoring Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fault Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Technical Support Contact . . . . . . . . . . . . . . . . . . . . . . . . .20
WARRANTY STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
CABLE SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
TOKEN RING MULTI-MEDIA REPEATER TECHNICAL
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Token Ring 2-Port
i
23
Multi-Media Repeater
Fiber Cable and Connector Specifications
The physical characteristics of the fiber cable must meet or exceed IEEE 802.3
10BaseFL specifications.
Cable Characteristics:
Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber
Optional: 100 / 140 µm multimode fiber
85 / 125 µm multimode fiber
50 / 125 µm multimode fiber
Fiber Optic Transmitter Power: Average power: -15.0 dBm
Peak power:-12.0 dBm ±1dBm
Fiber Optic Receiver Sensitivity: Average sensitivity: -27.4 dBm
Bit error rate: ≤10
-10
Connector Characteristics:
ST type connectors (SMA type available upon request)
Maximum Cable Distance (Determined by Cable and
Token Ring Speed)
SPEED: 16Mbps
Cable
Max-Lobe Length* Max-RI\RO Length*
UTP Category 3 150 meters (500 feet) 150 meters (500 feet)
UTP Category 5 350 meters (1140 feet) 350 meters (1140 feet)
STP Category 5 400 meters (1310 feet) 400 meters (1310 feet)
IBM Type 1 600 meters (1960 feet) 600 meters (1960 feet)
Fiber 2000 meters (6600 feet) 2000 meters (6600 feet)
SPEED: 4Mbps
Cable
Max-Lobe Length* Max-RI\RO Length*
UTP Category 3 200 meters (660 feet) 200 meters (660 feet)
UTP Category 5 600 meters (1960 feet) 600 meters (1960 feet)
STP Category 5 700 meters (2290 feet 700 meters (2290 feet)
IBM Type 1 800 meters (2620 feet) 800 meters (2620 feet)
Fiber 2000 meters (6600 feet) 2000 meters (6600 feet)
*Distances as tested with IBM Token Ring and SMC Token Elite Cards. Other
cards guaranteed to 100 meters per 802.5 specification.
Token Ring Cable Specifications
Page 4
Token Ring 2-Port
22
1
Multi-Media Repeater
1. INTRODUCTION
This guide is intended for the system or network administrator
responsible for installing and monitoring a TRANSITION Networks
Token Ring 2-Port Multi-Media Repeater. A working knowledge of
local area network (LAN) operations, including familiarity with
communications protocols used on interconnected LANs, is
assumed.
The Token Ring Multi-Media Repeater
The TRANSITION Networks Token Ring 2-Port Multi-Media
Repeater (TR-MMR-2), is a small, multi-purpose active retiming
Token Ring repeater that is site-configurable, using Slide In Card
(SIC) connections, for ring extension and/or for port extension over
selectable media.
• Reduces network jitter, particularly network jitter introduced by
passive MAUs, by regenerating and reshaping Token Ring
signals.
• Data Connector (IBM Type 1) SICs allow connection to a
shielded 150 ohm Token Ring network.
• Fiber optic SICs allow extension of Token Ring ring or lobe
connection up to 2000 meters (6600 feet).
• RJ-45 connector SICs allow cost-effective installation of
shielded and unshielded Token Ring twisted pair.
Token Ring 2 Port Multi Media Repeater
networks
TRANSITION
TR-MMR-02
Power
Ring In
Lobe In
Ring Out
Lobe Out
Reset
Speed
4
16
ZDL
Off
On
The sole purpose of this remedy shall be provided the customer with the replacement or
repair of non-conforming goods in the manner described in this Warranty statement. This
exclusive remedy shall not be deemed to have failed of its essential purpose so long as TN is
willing and able to repair or replace the defective item(s) or refund the purchase price.
TN reserves the right to inspect products claimed to be defective under warranty either at the
customer’s location or at TN’s plant. TN assumes no liability for liability charges incidental
to the adjustment, service, repairing, removal or replacement of the product, or other costs,
or the expense of repairs made outside of its factory, except when made with TN’s prior
written consent. Additionally, Transition Networks reserves the right to charge for all testing
and shipping incurred, if after testing, a return is classified as “No Problem Found”.
TN’s total liability in connection with the products and their installation to all persons and
from all causes in the aggregate, whether in contract, tort, or strict liability, shall not exceed
the amount paid to TN for the product directly related to the alleged damage. However, in
no event shall TN have any liability to a customer or any third party for products
manufactures according to the customer’s specifications.
C. Return Procedure
The customer must follow this procedure for the return of defective items:
1. Locate the serial number(s) of the item(s) to be returned.
2. Determine the date the item(s) was received.
3. Contact Transition Networks Technical Support to determine if the problem can be
corrected on site.
If not, and the product is covered by warranty, then:
• Call the distributor directly or contact TN.
• Request a Return Material Authorization (RMA).
• Ship the item, prepaid in original packaging to Transition Networks at the above
address.
• Include the RMA number on the outside of the carton and/or on the Packing List.
• Include a copy of the RMA form.
• Include a copy of the original invoice or packing list (if possible) to expedite
processing.
• The item(s) may be shipped by the customer or the distributor.
• Transition Networks will repair or replace the unit, at TN’s discretion, and cover the
cost of the return freight to the distributor or to the customer, whichever requested
the RMA number.
If the item(s) was received more than five years ago, or if the item(s) is no longer covered by
warranty for other reasons, then:
• Call the distributor or contact TN.
• Request a Material Repair Authorization number (MRA).
• Ship the item(s), prepaid, in the original packaging to Transition Networks at the
above address.
• Include the MRA number on the outside of the carton add/or on the Packing List.
• Include a copy of the MRA form.
• Include a copy of the original invoice or packing list (if possible) to expedite processing.
• Only the customer (end-user) may send the items(s) to TN.
• TN will contact the customer after the item(s) have been received, inspected, and a
cost estimate of the repair determined.
• The repair charges may be billed, with customer’s approval, though the distributor, or
on a prepaid or C.O.D. basis directly to the customer. The charges will include the
cost of shipping.
The return authorization numbers are valid only for 90 days from the date issued.
Page 5
Token Ring 2-Port
2
21
Multi-Media Repeater
Networking the Token Ring Multi-Media Repeater
Token Ring Multi-Media Repeater SIC cards connect two like or two
unlike media cables, selected from among IBM Type 1, multimode
fiber, and standard 100 ohm shielded twisted pair (STP) or unshielded
twisted pair (UTP).
As shown, the Token Ring Multi-Media Repeaters with installed cable
can be used both for ring extension (#1) and for lobe extension (#2).
R OR I
R OR I
RI RO
RI RO
IN
OUT
IN
OUT
IN
OUT
Lobe ExtensionRing Extension
Lobe Ports
Lobe Ports
#2#1
Warranty Statement
A. Five Year Warranty
Transition Networks, Inc. (TN) warrants, for a period of five years, that TN products (with
the exception of power supplies and fans that TN warrants for two years) will be free from
defects in materials and workmanship, and will be in conformity with TN’s specifications.
TN’s warranty on products manufactured by or assembled for TN in accordance with a
customer’s specifications, is a five-year warranty that the goods conform to such
specifications.
The warranty is invalidated if the goods have been subject to alterations, misuse, accident,
Acts of God (e.g., damage by floods, lightning strikes, Etc.), tampering, improper
maintenance, improper installation, or abuse. If the user is unsure about the proper means
of installing or using the equipment, contact TN’s free Technical Support or Network
Design Services, which can be reached by:
Telephone 1.800.LAN.WANS or 612.941.7600
Fax 612.941.2322
E-mail techsupport@transition.com
Internet http://www.transition.com
THE ABOVE WARRANTY IS EXCLUSIVE AND EXTENDS ONLY TO PRODUCTS
ASSEMBLED BY TRANSITION NETWORKS, INC. TO THE EXTENT PERMITTED BY LAW,
TN DOES NOT MAKE AND DISCLAIMS ALL OTHER WARRANTIES, EXCEPT TITLE,
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF
DESCRIPTION, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT, AND ANY WARRANTY BASED UPON PRIOR WRITTEN OR ORAL
REPRESENTATIONS REGARDING SUCH PRODUCTS MADE BY TN, ITS EMPLOYEES,
AGENTS, OR REPRESENTATIVES.
B. Limitations and Exclusions
If the customer believes any goods sold by TN are defective and within the warranty period,
the following general procedure will be followed:
1. Locate the serial number and delivery date of the item(s).
2. Notify TN within the warranty period.
3. TN will promptly issue a return authorization form for the goods.
4. Upon receiving the form, the customer will promptly return the item(s) at customers
own expense, shipped prepaid, to the distributor from which it was purchased, or
directly to TN.
TN will only accept goods for return if the following conditions have been met:
1. A return form is obtained from TN.
2. The freight charges have been prepaid by the customer.
3. Goods are re-packed in their original packaging.
If under warranty TN shall, at its option, (1) repair the goods free of charge (2) replace the
goods free of charge, or (3) accept the return of the item(s) and credit the current price to
the reseller (within 90 days of purchase), or (4) if the goods are not under warranty, will
repair the item(s) at a minimum charge of USD $200 (two hundred U.S. dollars) per item.
THIS IS THE EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. IN NO EVENT
SHALL TRANSITION NETWORKS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF ANY
CONDITION OF SALE, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY,
CONTRACT, OR OTHERWISE AND IRRESPECTIVE OF WHETHER TN IS INFORMED BY
CUSTOMER OF THE POSSIBILITY OF SUCH DAMAGES IN ADVANCE OF THIS SALE.
Page 6
Token Ring 2-Port
20
3
Multi-Media Repeater
Connectors, Switches and Status Indicators
Connectors
(AT BACK) Slide-In cards (SICs), when installed, provide IBM Data
Connectors, fiber connectors, and/or RJ-45 connectors.
An external power connector also is located at the Token Ring
Multi-Media Repeater back.
5. MAINTENANCE
WARNING: DO NOT, UNDER ANY CIRCUMSTANCES,
open and attempt to repair the Token Ring Multi-Media
Repeater. Failure to observe this warning could result in
personal injury or death from electrical shock.
NOTE: Failure to observe the above warning will immediately void
the warranty.
Fault Isolation
If two network devices fail to communicate through the Token Ring
Multi-Media Repeater, consider the following:
• Are the LEDs functioning properly?
• Do network devices communicate when the Token Ring
Multi-Media Repeater is not installed between them?
• Is flat or “silver satin” wire used in site internal wiring?
• Are internal wiring patch cords, punch down blocks, and
wall jacks properly pinned or configured?
• Are network interface cards properly configured?
Technical Support Contact
For assistance in fault isolation and in maintaining the Token Ring
Multi-Media Repeater, contact:
Technical Support (800) 260-1312
or your local distributor.
RI/LI SIC Slot
Power Connector
Power LED
Ring In/Lobe In LED
Ring Out/Lobe Out LED
Reset Switch
Network Speed Switch
ZDL Switch
RO/LO SIC Slot
Page 7
Token Ring 2-Port
4
19
Multi-Media Repeater
4. OPERATION
The Multi-Media Repeater requires no intervention beyond
occasionally monitoring the Power and Status LEDs.
Monitoring Power LED
When the green Power LED is illuminated, the Token Ring MultiMedia Repeater is connected to power.
Monitoring Status LEDs
When the Ring In/Lobe In LED is illuminated, the Token Ring MultiMedia Repeater is connected to an active ring or lobe input.
When the Ring Out/Lobe Out LED is illuminated, the Token Ring
Multi-Media Repeater is connected to an active ring or lobe output.
Switches
The Reset switch reinitializes the Token Ring Multi-Media Repeater.
The ZDL switch selects the Zero Delay Lockout feature.
The Speed switch selects between 16 Mbps and 4 Mbps network
speed.
Status Indicators (LEDs)
The Ring In/Lobe In LED indicates an active input connection to the
Token Ring Multi-Media Repeater.
The Ring Out/Lobe Out LED indicates an active output connection to
the Token Ring Multi-Media Repeater.
The Power LED monitors connection to external power.
Page 8
Token Ring 2-Port
18
5
Powering the Multi-Media Repeater
To power ON the Token Ring Multi-Media Repeater:
1. At Token Ring Multi-Media Repeater back, locate the power
receptacle and associated fuse.
NOTE: Fuse must be installed at correct setting for power source
voltage before connecting to AC outlet.
2. Verify that fuse is installed at correct setting for power source
voltage.
NOTE: The installed fuse rating is indicated by the reading at
lower right corner of fuse holder.
If not installed at correct setting for power source voltage:
• Carefully open fuse receptacle, using a small flat blade
screwdriver.
• Rotate fuse holder 180° to the correct rating orientation.
• Install fuse holder in correct rating orientation.
• Close fuse receptacle.
3. Plug unit end (female) of power cord into Token Ring MultiMedia Repeater power receptacle.
4. Plug outlet end (male) of power cord into correct voltage AC
wall socket.
5. At Token Ring Multi-Media Repeater front, verify that POWER
LED is illuminated.
110-120
110-120
220-240
220-240
110-120 Orientation 220-240 Orientation
Fuse Holder Fuse Holder
2. SITE CONSIDERATIONS
The site for the Token Ring Multi-Media Repeater must provide:
• AC power outlet for each Token Ring Multi-Media Repeater
• Adequate ventilation
• Standard environmental conditions
• Isolation from electrical noise, including radio transmitters and
broadband amplifiers, motors, high power electrical lines, or
fluorescent light fixtures.
And, if using twisted pair cable:
• The twisted pair cables should not run in the same conduit with
power line cables,
• Phone lines should be separated from data cables,
• Flat or “silver satin” wires should not be used,
• All Token Ring twisted pair cable should be configured as
straight through.
Page 9
Token Ring 2-Port
6
17
Multi-Media Repeater
Setting Configuration Switches
1. Set the Token Ring Multi-Media Repeater network Speed
switch to match the network speed (4 Mbps or 16 Mbps).
2. Set the Token Ring Multi-Media Repeater ZDL switch to ON to
enable automatic speed detection (unless connecting non-
802.5 compliant test equipment such as Hewlett Packard
Token Ring tester).
3. Press the reset button.
Reset Switch
Network Speed Switch
ZDL Switch
Token Ring 2 Port Multi Media Repeater
networks
TRANSITION
TR-MMR-02
Power
Ring In
Lobe In
Ring Out
Lobe Out
Reset
Speed
4
16
ZDL
Off
On
Token Ring Twisted Pair Network Considerations
Twisted pair cables between passive MAUs and Token Ring MultiMedia Repeaters must be short (patch cables). The patch cables can be
either Type 1 (150 Ω) twisted pair or Category 5 (100 Ω) twisted pair.
At 16Mbps network speed, shielded twisted pair (STP) cables between
Token Ring Multi-Media Repeaters or between Token Ring Multi-Media
Repeaters and terminal equipment can be up to 400 meters (1310 feet);
unshielded twisted pair (UTP) cables can be up to 350 meters (1140
feet).
Type 1 (150 Ω) Patch Cable
RI
RO
RI RO
RI RO
Category 5 (100 Ω) UTP Patch Cable
LI
LO
Category 5 (100 Ω) UTP
Up to 350 meters @ 16Mbps
RI
RO
Type 1 (150 Ω) Patch Cable
Category 5 (100 Ω) STP
Up to 400 meters @ 16Mbps
Page 10
Token Ring 2-Port
16
7
Multi-Media Repeater
Token Ring RJ-45 Twisted Pair Configuration
If twisted pair cable is used, the twisted pair cable and RJ-45 jacks must
be configured as straight through.
The two active pairs in a Token Ring network are pins 4 & 5 and
pins 3 & 6. Use only dedicated wire pairs (such as blue/white &
white/blue, orange/white & white/orange) for the active pins.
Straight Through Cable
at RJ-45 Plug
RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male
3 . . . . . . . . . . . . . . . . . . .3
4 . . . . . . . . . . . . . . . . . .4
5 . . . . . . . . . . . . . . . . . .5
6 . . . . . . . . . . . . . . . . . . .6
1
8
RJ-45 PLUG
1823456
7
RJ-45 JACK
RJ CONNECTOR LOBE EXTENSION
If the twisted pair slide-in card is installed in a Token Ring Multi-Media
Repeater which is connected in a lobe extension installation to an
active hub or MAU OR to a passive MAU, set Active/Passive switch on
the twisted pair SIC to Active.
TR -RJ -SIC
OUT
Set switch to ACTIVE
TR -RJ -SIC
Set switch to ACTIVE
IN
Passive MAU
RI
RO
TR -RJ -SIC
OUT
Set switch to ACTIVE
TR -RJ -SIC
Set switch to ACTIVE
IN
Active Hub
NOTE: Category 3 wire or better is required. Category 5 wire is
recommended for long distances. See page 23 for wiring distances.
Either shielded twisted pair (STP) or unshielded twisted pair (UTP) can
be used.
DO NOT USE FLAT OR “SILVER SATIN” WIRE.
Page 11
Token Ring 2-Port Multi-Media Repeater
8
15
3. INSTALLATION
To install the Token Ring Multi-Media Repeater:
• Unpack the Token Ring Multi-Media Repeater
• Install Multi-Media Repeater on flat surface
• Install Slide In Cards (SICs)
• Connect cable to SIC connectors
• Set configuration switches
• Power the Multi-Media Repeater.
Direction is provided in the pages that follow.
Unpacking the Token Ring Multi-Media Repeater
The Token Ring Multi-Media Repeater packing contents should include
the following:
Item Part Number
Token Ring
Multi-Media Repeater TR-MMR-2
Power Cord 3344, 3347, 3348, 3349, or 3523,
(depending upon power configuration
in country where installed)
User’s Guide 7363
In addition, any of the following optional SICs may be included:
Item Part Number
Data Connector SIC TR-DC-SIC
Fiber Optic
Ring In/Lobe In SIC TR-FI-SIC
Fiber Optic
Ring Out/Lobe Out SIC TR-FO-SIC
RJ-45 SIC TR-RJ-SIC
RJ-45 Connection
The twisted pair slide-in card TR-RJ-SIC
can provide a cost-effective method for
eliminating jitter by connecting passive
hubs with active hubs and/or with
terminal equipment.
RJ CONNECTOR ACTIVE/PASSIVE RING EXTENSION
If the twisted pair slide-in card is installed in a Token Ring Multi-Media
Repeater which is connected in a ring extension installation to an
active hub, set Active/Passive switch on the twisted pair SIC to Active.
If the twisted pair slide-in card is installed in a Token Ring Multi-Media
Repeater which is connected in a ring extension installation to a
passive hub, set Active/Passive switch on the twisted pair SIC to
Active
Passive
UTP/STP
Token Ring
Slide In Card
TR-RJ-SIC
networks
TRANSITION
IN
OUT
RI RO
RI
RO
RI
RO
IN
OUT
Page 12
Token Ring 2-Port Multi-Media Repeater
14
9
Installing Multi-Media Repeater on Flat Surface
To install the Multi-Media Repeater on a table, shelf, or other flat
surface:
1. Carefully turn Token Ring Multi-Media Repeater to side.
2. Install four (4) rubber feet:
• Remove protective paper from adhesive surface of rubber
foot.
• Position rubber foot at bottom corner of Token Ring Multi-
Media Repeater.
• Secure rubber foot to Token Ring Multi-Media Repeater
surface.
• Repeat for remaining rubber feet.
3. Return Token Ring Multi-Media Repeater to upright position.
FIBER CONNECTOR LOBE EXTENSION
NOTE: Fiber Ring In/Lobe In SIC card MUST BE INSTALLED in the
RI/LI SIC card location. Fiber Ring Out/Lobe Out SIC card MUST BE
INSTALLED in the RO/LO SIC card location.
Install two-stranded fiber cable by connecting Ring In/Lobe In TX to
Ring Out/Lobe Out RX and Ring In/Lobe In RX to Ring Out/Lobe Out
TX.
RI RO
Passive MAU
TR -FO-SIC
TR -xx -SIC
TR -FI -SIC
TR -xx -SIC
IN
OUT
IN
OUT
Active Hub
TR -FO-SIC
TR -xx -SIC
TR -FI -SIC
TR -xx -SIC
IN
OUT
IN
OUT
Page 13
Token Ring 2-Port Multi-Media Repeater Hub
10
13
Installing Slide-In Cards (SICs)
CAUTION: Wear a grounding device and observe electrostatic
discharge precautions when installing Slide-In Cards. Failure to
observe this caution could result in circuit board failure.
NOTE: SIC card configured RI/LI MUST be installed in RI/LI SIC slot;
SIC card configured RO/LO MUST be installed in RO/LO SIC slot.
To install a Slide-In Card:
1. Determine if Slide-In Card has RI/LI-RO/LO switch and, if so,
determine if RI/LI-RO/LO switch is in correct position for the
installation. If necessary, reset RI/LI-RO/LO Switch.
NOTE: RI/LI-RO/LO switch settings are marked on Slide-In
Card component surface.
NOTE: Fiber SIC does NOT have RI/LI-RO/LO switch.
2. With Slide-In Card components facing up, carefully guide
Slide-In Card along card guides until Slide-In Card connector
meets Token Ring Multi-Media Repeater backplane.
3. Firmly seat Slide-In Card against internal connector until
Slide-In Card faceplate is flat against Token Ring Multi-Media
Repeater frame.
4. Rotate Slide-In Card thumbscrews into Token Ring MultiMedia Repeater threaded holes.
RI/LI-RO/LO
Switch
Fiber Connection
The fiber slide-in cards TR-FI-SIC and TR-FO-SIC can be installed in
two separate Token Ring Multi-Media Repeaters and used in pairs to
extend the Token Ring network by 2000 meters (6600 feet).
FIBER CONNECTOR RING EXTENSION
TR-FI-SIC
Token Ring
Fiber Optic
Slide In Card
networks
TRANSITION
RX TX
Ring In/Lobe In
TR-FO-SIC
Token Ring
Fiber Optic
Slide In Card
networks
TRANSITION
RX TX
Ring Out/Lobe Out
RI RO
Passive MAU
IN
OUT
TR -FO -SIC
TR -xx -SIC
RI RO
Active Hub
IN
OUT
TR -FI-SIC
TR -xx -SIC
Page 14
DATA CONNECTOR PASSIVE RING EXTENSION
If the data connector slide-in card is installed in a Token Ring MultiMedia Repeater which is connected in a ring extension installation to a
passive hub or MAU, set Active/Passive switch to Passive.
DATA CONNECTOR LOBE EXTENSION
If the data connector slide-in card is installed in a Token Ring MultiMedia Repeater which is connected in a lobe extension installation to
an active hub or MAU OR to a passive MAU, set Active/Passive switch
to Active.
Token Ring 2-Port Multi-Media Repeater Hub
12
11
Connecting Cable to SIC Connectors
Data Connector Connection
The slide-in card TR-DC-SIC can be used
for connecting the Token Ring MultiMedia Repeater to a shielded 150 ohm
Token Ring network, using Data
Connectors.
The TR-DC-SIC data connector installation can be used for active or
passive ring extension and/or for lobe extension
DATA CONNECTOR ACTIVE RING EXTENSION
If the data connector slide-in card is installed in a Token Ring MultiMedia Repeater which is connected in a ring extension installation to
an active hub or MAU, set Active/Passive switch on the Data
Connector SIC to Active.
TR-DC-SIC
Active
Passive
Set switch to ACTIVE
RI RO
Passive MAU
TR -DC-SIC
TR -xx -SIC
IN
OUT
Set switch to ACTIVE
TR -DC-SIC
TR -xx -SIC
IN
OUT
TRANSITION
PN ICS-45-CN
Type 1 to
RJ-45 adapter
patch cable
Active Hub
RI RO
Passive MAU
Set switch to PASSIVE
IN
OUT
TR -DC-SIC
TR -xx -SIC
RI RO
TRANSITION
PN ICS-45-CN
Type 1 to
RJ-45 adapter
patch cable
Active Hub
Set switch to ACTIVE
IN
OUT
TR -DC-SIC
TR -xx -SIC
RI RO
Active MSAU
Set switch to ACTIVE
IN
OUT
TR -DC-SIC
TR -xx -SIC
Loading...