Transition Networks SSDTF1014-100, SSDTF1015-100, SSDTF1011-100, SSDTF1013-100, SSDTF1012-100, SSDTF1022-100 User Manual

163.44 Kb
Loading...

COMPLIANCE INFORMATION

UL Listed

C-UL Listed (Canada) CISPR22/EN55022 Class A + EN55024 CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques appropriées

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

Copyright Restrictions

© 2001, 2002 TRANSITION Networks.

All rights reserved. No part of this work may be reproduced or used in any form or by any means – graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A.

33202.C

T1/E1 Twisted-Pair Copper to Fiber

Media Converters

SSDTF10xx*-100

USER’S GUIDE

TRANSITION Networks SSDTF10xx-100 series media converters encode and decode T1 or E1 twisted-pair copper signals over duplex fiber-optic cable to extend the distance and transmission reliability of high speed T1 or E1 data traffic.

SSDTF1011-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and a set of RX/TX ST connectors to 850 nm multimode duplex fiber-optic cable.

SSDTF1012-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX ST connector to 1300 nm singlemode duplex fiber-optic cable.

SSDTF1013-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC connector to 850 nm multimode duplex fiber-optic cable.

SSDTF1014-100

Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC-SM connector to 1300 nm singlemode duplex fiber-optic cable.

9-12 VDC INPUT

T!/E1 TP to Fiber Media Converter

SSDTF1015-100 (long haul) Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX SC-LH connector to 1300 nm singlemode duplex fiber-optic cable.

SSDTF1022-100 (long haul) Provides an RJ-45 twisted pair copper connector for T1 or E1 signals and an RX/TX ST connector to 1300 nm singlemode duplex fiber-optic cable.

*In SSDTF10xx model designation, 10 represents the T1 or E1 RJ-45 connector; xx represents the selectable fiber connector installed on the media converter.

SSDTF10xx in the Network . .

. . . . .2

Installation . . . . . . . . . . . . . . . .

. . . .3

Operation . . . . . . . . . . . . . . . . .

. . . .7

Fault Isolation and Correction

. . . . .8

Cable Specifications . . . . . . . . .

. . . .9

Technical Specifications . . . . . .

. . .11

Compliance Information . . . . . .

. . .12

SSDTF10xx IN THE NETWORK

NOTE: THE SSDTF10xx REQUIRES A CSU BETWEEN THE MEDIA CONVERTER AND THE PUBLIC TELEPHONE NETWORK.

T1 Network Extension

CSU

NOTE: T1/E1 MEDIA CONVERTERS MUST BE USED IN PAIRS. A TRANSITION Networks SSDTF10xx stand-alone media converter can be used with another SSDTF10xx stand-alone media converter, with a CSDTF10xx chassis media converter, or with a previous model TRANSITION Networks T1/E1 media converter, such as a C/T1E1-CF-01 or a T1E1-CF-01.

Features

Media converter is framing independent (as ESF vs D4) and supports all common line codes, (AMI, B8ZS, HDB3).

Dry relay contacts allow media converter to be tied into separate alarm circuit

All Ones Insertion (AIS) on loss of signal at copper and/or fiber interface.

TECHNICAL SPECIFICATIONS

Standards

Emissions: CISPR A

 

T1/E1 Physical Layer: ITU-T, ANSI, AT&T, ETSI

Dimensions

2.9" x 4.8" x 1.4"

Weight

8 oz (approximate)

Power Source

7.5-15.9 VDC AC Adapter

Power Consumption

5 watts

Power Supply Requirements Replace power supply with only the equivalent input rating (see below) and output rating (regulated 9VDC at 550 mA).

TN PN

Requirement

Location

25034 or 3525 240 volts, 50 hertz

United Kingdom

25034 or 3525 230 volts, 50 hertz

Europe

3518

120 volts, 60 hertz

USA/Canada/Mexico

3514

100 volts, 50-60 hertz

Japan

25034 or 3525 240 volts, 50 hertz

Australia

Environment

Typical Operating Temperature*: 0° to 50°C (32° to 122°F )

 

Storage Temperature:

-20° to 85°C (-4° to 185°F)

 

Humidity

10-90%, non condensing

 

Altitude

0-10,000 feet

Warranty

Lifetime

 

 

 

 

DECLARATION OF CONFORMITY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name of Mfg:

Transition Networks

 

 

6475 City West Parkway, Minneapolis MN 55344 USA

Model: SSDTF10xx Series Copper-to-Fiber Media Converter

Part Number: SSDTF1011-100, SSDTF1012-100, SSDTF1013-100,

SSDTF1022-100 Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the SSDTF10xx to which this declaration refers is in conformity with the following standards.

EN 55022:1994; EN 55024:1998; FCC Part 15 Class A; EN 60950 A4:1997; UL 1950

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s).

 

 

 

_January 8, 2001_____

 

Stephen Anderson, Vice-President of Engineering

Date

 

 

 

 

+ 4 hidden pages