Transition Networks CSDTF1022-100 User Manual

COMPLIANCE INFORMATION

UL Listed
C-UL Listed (Canada)
CISPR22/EN55022 Class A + EN55024
CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

Copyright Restrictions

© 2001, 2002 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A. 33201.C

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten

verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur

Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

TRANSITION Networks CSDTF10xx-100 series media converters, designed to be
installed in a PointSystem

™

Conversion Center™chassis, encode and decode T1 or

E1 twisted-pair copper signals over duplex fiber-optic cable to extend the distance
and transmission reliability of high speed T1 or E1 data traffic.

*In CSDTF10xx model designation, 10
represents the T1 or E1 RJ-45 connector;
xx represents the selectable fiber connector
installed on the media converter.

T1/E1 Twisted-Pair Copper

to Fiber

Slide-In-Module Media Converters

CSDTF10xx*-100

USER’S GUIDE

CSDTF1011-100

Provides an RJ-45 twisted pair copper
connector for T1 or E1 signals and a set
of RX/TX ST connectors to 850 nm
multimode duplex fiber-optic cable.

CSDTF1012-100

Provides an RJ-45 twisted pair copper
connector for T1 or E1 signals and an
RX/TX ST connector to 1300 nm
singlemode duplex fiber-optic cable.

CSDTF1013-100

Provides an RJ-45 twisted pair copper
connector for T1 or E1 signals and an
RX/TX SC connector to 850 nm
multimode duplex fiber-optic cable.

CSDTF1014-100

Provides an RJ-45 twisted pair copper
connector for T1 or E1 signals and an
RX/TX SC-SM connector to 1300 nm
singlemode duplex fiber-optic cable.

CSDTF1015-100 (long haul)

Provides an RJ-45 twisted pair copper
connector for T1 or E1 signals and an
RX/TX SC-LH connector to 1300 nm
singlemode duplex fiber-optic cable.

CSDTF1022-100 (long haul)

Provides an RJ-45 twisted pair copper
connector for T1 or E1 signals and an
RX/TX ST connector to 1300 nm
singlemode duplex fiber-optic cable.

CSDTF10xx in the Network . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . .7

Fault Isolation and Correction . . . . .8

Cable Specifications . . . . . . . . . . . .10

Technical Specifications . . . . . . . . .11

Compliance Information . . . . . . . . .12

M

50‰

PWR

PWR

SDC

SDC

SDF

PWR

DB-9

SET

LKS

LKM

RXF

LOOP

LKC

RXC

TX

Singlemode

TX

RX

RX

TX

Multimode

RX

CSDTF100

CFMFF100

LKS

LKM

TX

Singlemode

RX

TX

Multimode

RX

CFMFF100

SDF

TX

RX

CFETF100

PWR

PWR

SDC

PWR

LA

LNK

RXF

LOOP

RXC

Link Alert

E

10BASE-T

0

10BASE-2

CECF100

SDF

LKS

LKM

COL

TX

Singlemode

D

TX

RX

TX

RX

Multimode

50‰

RX

CFMFF100

CFETF110

PWR

LOOP

LKS

LKM

TX

Singlemode

RX

TX

Multimode

RX

CF

CSDTF10xx IN THE NETWORK

NOTE: THE CSDTF10xx REQUIRES A CSU BETWEEN THE MEDIA
CONVERTER AND THE PUBLIC TELEPHONE NETWORK.

NOTE: T1/E1 MEDIA CONVERTERS MUST BE USED IN PAIRS. A TRANSITION
Networks CSDTF10xx chassis media converter can be used with another
CSDTF10xx chassis media converter, a SSDTF10xx stand-alone media
converter, or with a previous model TRANSITION Networks T1/E1 media
converter, such as a C/T1E1-CF-01 or a T1E1-CF-01.

Features

• Media converter is framing independent (as ESF vs D4) and supports all
common line codes, (AMI, B8ZS, HDB3).

• Dry relay contacts allow media converter to be tied into separate alarm
circuit

• All Ones Insertion (AIS) on loss of signal at copper and/or fiber interface.

TECHNICAL SPECIFICATIONS

Standards Emissions: CISPR A

T1/E1 Physical Layer: ITU-T, ANSI, AT&T, ETSI

Dimensions 2.9" x 4.8" x 1.4"
Weight 8 oz (approximate)
Power Consumption 5 watts

Environment Typical Operating Temperature*: 0°

to 50°C (32° to 122°F )

Storage Temperature: -20°

to 85°C (-4° to 185°F)

Humidity 10-90%, non condensing
Altitude 0-10,000 feet

Warranty Lifetime
*Operating temperature range for this Slide-In-Module depends on the physical

characteristics and the installation configuration of the TRANSITION Networks
chassis in which this Slide-In-Module will be installed. See the User’s Guide for
the chassis in which this Slide-In-Module will be installed for a discussion of
temperature-related installation constraints.

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA
Model: CSDTF10xx Series Copper-to-Fiber Media Converter
Part Number: CSDTF1011-100, CSDTF1012-100, CSDTF1013-100,

CSDTF1022-100

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the CSDTF10xx to which this declaration refers is in

conformity with the following standards.
EN 55022:1994; EN 55024:1998; FCC Part 15 Class A; EN 60950 A4:1997; UL 1950

I, the undersigned, hereby declare that the equipment specified above conforms to the

above Directive(s) and Standard(s).

_January 8, 2001_____

Stephen Anderson, Vice-President of Engineering Date

T1/E1 Network Extension

Media
Conversion
Center

PWR

10BASE-T

DB-9

Power

LKC

1

In Use

Power

2

In Use

INPORT

RESET

INIT

12C

OUTPORT

PWR

TX

12C-1TERM

RX

LNK

MCCM10

MGMT MASTER

PWR

SPD

FLNK

FRX

SPD

PWR

LKF

FRX

RXF

CRX

CLNK

CRX

LKC

RXC

TX

TX

TX

100BASE-FX

100BASE-FX

10BASE-FL

RX

RX

10BASE-T

RX

CFETF100

CETTF100

SPD

FRX

PWR

PWR

SPD

FLNK

FLNK

FRX

CRX

CLNK

CRX

CLNK

TX

TX

10/100SX

10/100SX

RX

10/100TX

RX

CFETF110

10/100TX

Media
Conversion
Center

10BASE-T

Power

1

In Use

Power

2

In Use

INPORT

OUTPORT

MGMT MASTER

PWR

SPD

FLNK

FRX

CRX

CLNK

TX

100BASE-FX

RX

PWR

PWR

SPD

PWR

PWR

LKF

DB-9

RXF

LKC

RXC

TX

10BASE-FL

RESET

INIT

RX

12C

PWR

TX

10BASE-T

12C-1TERM

RX

LNK

MCCM10

CETTF100

SPD

FLNK

FRX

LKC

FLNK

FRX

CLNK

CRX

CRX

CLNK

TX

100BASE-FX

TX

10/100SX

RX

RX

10/100TX

CFETF100

CFETF110

PWR

SPD

FLNK

FRX

CRX

CLNK

TX

100BASE-FX

RX

SPD

FRX

CRX

TX

10/100SX

RX

10/100TX

CSU

CABLE SPECIFICATIONS (continued)

Twisted-Pair Copper Cable

Twisted pair connection requires two active pairs. The two active pairs
in a T1/E1 network are pins 1 & 2 and pins 4 & 5. Use only dedicated
wire pairs (such as blue/white & white/blue, orange/white &
white/orange) for the active pins.

Category 3 or better twisted-pair copper wire is required. Either shielded
twisted-pair (STP) or unshielded twisted-pair (UTP) can be used.

T1:

Gauge 24 to 22 AWG
Attenuation 2.6 dB/100 meters @ 1.0 MHz
Differential Characteristic Impedance 100 Ω ±10%

E1:

Gauge 24 to 22 AWG
Attenuation 2.6 dB/100 meters @ 1.0 MHz
Differential Characteristic Impedance 120 Ω ±10%

Dry-Contact Relay

RJ-45 dry-contact relay opens if power, signal detect/copper or signal
detect/fiber are lost.

Operational rating on pins 3 and 6: 0-30VDC maximum 1A

Switch-Selectable Configurations

T1 COPPER RJ-45

Configured as either "long haul" or “short haul” on 100 ohm cable, with
a variety of selectable distance settings.

E1 COPPER RJ-45

Configured as either "long haul" or “short haul” on 120 ohm cable.

STRAIGHT-THROUGH/CROSSOVER RJ-45

Allows straight-through cable to be used where crossover-configuration
cable is required.

Switch-Selectable Functions

LOOPBACK TEST FUNCTION

A loopback switch facilitates installation and network debug procedures.
The path for the CSDTF10xx loopback is shown:

TRANSMIT ALL ONES FUNCTION

A selectable Transmit All Ones switch on the fiber interface and on the
twisted-pair interface allows for insertion of an “all ones” pattern on that
interface when signal detect is lost, which creates an alarm condition at
the equipment connected to the interface.

Relay

3

6

RJ-45

TP

Fiber

TP

INSTALLATION

CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting switch and when installing Media Converter Slide-in­Module in the Media Conversion Center. Failure to observe this caution could
result in damage to, and subsequent failure of, the Media Converter Slide-in­Module.

Set Loopback Test Switch

NOTE: The Loopback Test switch, located on Media Converter Slide-in­Module front panel, allows the network administrator
to enable a loopback test for installation and network
debug procedures.

Use small flatblade screwdriver or similar device to set recessed switches.
Refer to drawing for switch locations.

Set 3-Position Jumper

NOTE: Jumper is located on Media Converter Slide-in-Module circuit board.
Use small needle-nosed pliers or similar device to set

jumper. Refer to drawing for jumper positions.
HARDWARE Converter mode is determined by

4-position switch settings below.
SOFTWARE Converter mode is determined by most-

recently-saved on-board microprocessor settings.

Set MDI/MDI-X Switch

NOTE: The MDI/MDI-X switch, located on Media Converter Slide-in-Module
circuit board, allows the network administrator to use straight-through cable
in installations where crossover-configuration cable is required.

Use small flatblade screwdriver or similar device to set recessed switches.
Refer to drawing for switch settings.

Set 8-Position Switch

NOTE: The eight-position switch, located on Media Converter Slide-in­Module circuit board, allows the network administrator to configure the
media converter for network conditions.

Use small flatblade screwdriver or similar device to set recessed switches for
site installation. Refer to drawings at right for eight-position switch settings.

CABLE SPECIFICATIONS

Fiber Cable

Bit error rate: ≤10-9

MULTIMODE

Fiber Optic Cable Recommended: 62.5 / 125 µm multimode fiber

Optional: 100 / 140 µm multimode fiber

85 / 125 µm multimode fiber

50 / 125 µm multimode fiber
CSDTF1011-100 850 nM
Fiber Optic Transmitter Power: min: -14.0 dBm max: -12.0 dBm
Fiber Optic Receiver Sensitivity: min: -25.0 dBm max: -12.0 dBm
Typical Maximum Cable Distance*: 2 kilometers
CSDTF1013-100 850 nM
Fiber-optic Transmitter Power: min: -14.0 dBm max: -12.0 dBm
Fiber-optic Receiver Sensitivity: min: -25.0 dBm max: -12.0 dBm
Typical Maximum Cable Distance*: 2 kilometers

SINGLEMODE

Fiber Optic Cable Recommended: 9 µm singlemode fiber
CSDTF1012-100 1300 nM
Fiber-optic Transmitter Power: min: -21.0 dBm max: -14.0 dBm
Fiber-optic Receiver Sensitivity: min: -25.0 dBm max: -14.0 dBm
Typical Maximum Cable Distance*: 8 kilometers
CSDTF1014-100 1300 nM
Fiber-optic Transmitter Power: min: -21.0 dBm max: -14.0 dBm
Fiber-optic Receiver Sensitivity: min: -27.0 dBm max: -14.0 dBm
Typical Maximum Cable Distance*: 8 kilometers
CSDTF1015-100 (long haul) 1300 nM
Fiber-optic Transmitter Power: min: -15.0 dBm max: -5.0 dBm
Fiber-optic Receiver Sensitivity: min: -27.0 dBm max: -14.0 dBm
Typical Maximum Cable Distance*: 15 kilometers
CSDTF1022-100 (long haul) 1300 nM
Fiber-optic Transmitter Power: min: -15.0 dBm max: -5.0 dBm
Fiber-optic Receiver Sensitivity: min: -25.0 dBm max: -14.0 dBm
Typical Maximum Cable Distance*: 15 kilometers

*Actual distance dependent upon physical characteristics of network installation.

Loop

H

HARDWARE MODE

H

SOFTWARE MODE

Twisted
Pair #1

1
2

RTIP

RRING

MDI

TTIP

TRING

Twisted
Pair #1

1
2

RTIP

RRING

MDI-X

RTIP

RRING

S

S

Twisted
Pair #2

TTIP

4
5

TRING

Connectors for unlike devices

RTIP

RRING

Twisted
Pair #2

TTIP

4
5

TRING

Connectors for like devices

TTIP

TRING

FAULT ISOLATION and CORRECTION

If the media converter fails, isolate and correct the failure by determining the
answers to the following questions and then taking the indicated action:

1. Is the P(o)W(e)R LED on the media converter illuminated?
NO

• Is the media converter inserted properly into the chassis?

• Is the power cord properly installed in the chassis and at the

external power source?

• Does the external power source provide power?

• Contact Technical Support: [phone].

YES

• Proceed to step 2.

2. Is the SDF (Signal Detect/Fiber) LED illuminated?
NO

• Check fiber cables for proper connection.

• Verify that TX and RX cables on media converter are connected to

RX and TX ports, respectively, on other media converter.

• Contact Technical Support: [phone].

YES

• Proceed to step 3.

3. Is the SDC (Signal Detect/Copper) LED illuminated?
NO

• Check twisted pair cables for proper connection.

• Check RJ-45 Pinning Switch for correct twisted pair cable

configuration.

• Check integrity of device attached to media converter by twisted-

pair cable.

• Contact Technical Support: [phone]/(800) LAN-WANS.

YES

• Contact Technical Support: [phone]/(800) LAN-WANS.

NOTE:
T1 must be selected (

LEFT

SWITCH SET

#4 UP) for

RIGHT

SWITCH SET

to have any effect.

If E1 is selected (

LEFT SWITCH SET

#4 DOWN), RIGHT SWITCH SET

is

ignored and the default is E1

3.0V 120Ω cable.
If T1 and short haul are

selected (

LEFT SWITCH SET

#3

UP, #4 UP), but

RIGHT SWITCH

SET

is not set to a valid short
haul value, the short haul
default is DSX-1 0’-133’ cable.

If T1 and long haul are
selected (

LEFT SWITCH SET

#3

DOWN, #4 UP), but

RIGHT

SWITCH SET

is not
set to a valid
long haul value,
the long haul
default is 0db
100Ω cable.

KEY

= UP

= DOWN

RIGHT SWITCH SET

1 2 3 4

toward chassis

1 2 3 4

toward network connectors

LONG HAUL Switch Settings*

1 2 3 4

-22.5db

12

100 ohm cable

LEFT SWITCH SET

toward chassis

NETWORK Switch Settings

1 2 3 4

12

12

12

12

1 2 3 4

1 2 3 4

toward network connectors

Transmit All Ones onto Fiber
on loss of TP Carrier Detect

UP= Enabled

Transmit All Ones onto TP
on loss of FiberCarrier Detect

UP= Enabled

Long Haul/Short Haul (T1 only)

UP= Short Haul

T1/E1 Selection

UP= T1

SHORT HAUL Switch Settings*

1 2 3 4

DSX-1 533'-655'

12

12

12

100 ohm cable

DSX-1 399’-533’
100 ohm cable

DSX-1 266’-399’
100 ohm cable

-15db

12

100 ohm cable

-7.5db

12

100 ohm cable

0db

12

100 ohm cable

*Right switch set #4 not used

DSX-1 133'-266'

12

100 ohm cable

DSX-1 1 0’-133’

12

and ANSI T1.403
100 ohm cable

DSX-1 6.0V

12

100 ohm cable

*Right switch set #4 not used

INSTALLATION

(continued)

Install Slide-In-Module in PointSystem™Chassis

CAUTION: Any Slide-in-Module installation slot in which a Media Converter
Slide-in-Module is NOT installed MUST have a protective plate instead.
Failure to observe this caution will void Class A and/or Class B compliance.

NOTE: Install Media Converter Slide-in-Modules in any slot, in any order.

1. Carefully slide Media Converter Slide-in-Module into installation slot,
aligning Media Converter Slide-in-Module with installation guides.

NOTE: Ensure that Slide-in-Module is firmly seated against backplane.

2. Secure Slide-in-Module by securing panel fastener screw (attached to
Slide-in-Module) to chassis front.

3. Install protective plate at EVERY Slide-in-Module installation slot in
which a Media Converter Slide-in-Module is not installed by securing
attached protective plate panel fastener screw to chassis front.

Install Cable

COPPER

T1 100 OHM (RJ-45 CONNECTOR)

1. Locate or build twisted-pair cables that are compliant with

specifications on page 10, with RJ-45 plug connectors at both ends.

2. Ensure that MDI/MDI-X switch is set according to network

conditions.

3. Connect RJ-45 plug connector at one end of cable to media

converter RJ-45 jack connector.

4. Connect RJ-45 plug connector at other end of cable to network

equipment.

FIBER

1. Locate or build fiber cables that are compliant with specifications

on page 9, with male two-stranded TX to RX connectors installed at
both ends.

2. Connect cable with connector installed at TX location on media

converter to RX location on attached device.

3. Connect cable with connector installed at RX location on media

converter to TX location on attached device.

Power the Slide-In-Module

NOTE: The Slide-In-Module is powered through the Conversion

Center

™

.

OPERATION

After installation, the media converter should function without operator
intervention.

Status LEDs

Use the status LEDs to monitor media converter operation in the network.
SDC Signal Detect/Copper - Steady LED

indicates twisted-pair copper link is up.
Flashing LED (once/second) indicates

transmitting on link if other link is down.
Flashing LED (5 times/second) indicates All

Ones detected on Link.

SDF Signal Detect/Fiber - Steady LED indicates fiber link is up.

Flashing LED (once/second) indicates transmitting on link if
other link is down.

Flashing LED (5 times/second) indicates All Ones detected on
Link.

P(o)W(e)R Steady green LED indicates connection to external AC power.

Using SNMP*

Use SNMP at an attached terminal or at a remote location to:

• Monitor media converter by monitoring:

Media Converter Power
Fiber Link Status
Copper Link Status
Hardware Switch settings
AIS detected on Fiber
AIS detected on Copper

• Enter network commands that:

Enable/disable Loop-back on Fiber
Enable/disable Transmit All Ones on Fiber when Copper is down
Enable/disable Transmit All Ones on Copper when Fiber is down
Power Down Media Converter.

*See the on-line documentation that comes with TRANSITION Networks

FocalPoint

™

software for applicable commands and usage.

TX

RX

TX

RX

SDC

SDF

PWR

LOOP