Transition Networks CGETF1013-100, CGETF1014-100, CGETF1015-100, CGETF1017-100, CGETF1018-100 User Manual

COMPLIANCE INFORMATION

UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A
EN55024

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

Copyright Restrictions

© 2001 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A. 33198.C

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

TRANSITION Networks CGETF10xx series Gigabit Ethernet™media converters,

designed to be installed in a PointSystem

™

Conversion Center

™

, connect

1000BASE-TX shielded or unshielded twisted-pair copper cable to 1000BASE-SX
or 1000BASE-LX multimode or singlemode fiber-optic cable.

1000BASE-TX to 1000BASE-SX/LX

Slide-In-Module Media Converters

CGETF10xx-100

USER’S GUIDE

CGETF1013-100

Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 850 nm 1000BASE-SX multimode
fiber-optic cable.

CGETF1014-100

Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 1300 nm 1000BASE-LX singlemode
fiber-optic cable.

CGETF1015-100

Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 1300 nm 1000BASE-LX singlemode
fiber-optic cable.

CGETF1017-100

Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) SC connector
to 1550 nm 1000BASE-LX singlemode
fiber-optic cable.

CGETF1018-100

Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) MT-RJ
connector to 850 nm 1000BASE-SX
multimode fiber-optic cable.

CGETF1025-100

Provides an RJ-45 twisted-pair copper
1000BASE-T connector and an RX
(receive) and TX (transmit) MT-RJ
connector to 1300 nm 1000BASE-LX
singlemode fiber-optic cable.

CFMFF100

CFMFF100

CFMFF100

CFMFF100

CETCF100

CETCF100

CFETF110

0

SPD

PWR

FRX

CRX

FLNK

CLNK

10/100TX

RX

TX

10/100SX

Link

Link

Alert

Alert

E

D

0

50

50

‰

LA

PWR

PWR

RXF

RXC

LNK

LNK

COL

COL

10BASE-2

10BASE-FL

LKS

LKS

PWR

PWR

LKM

LKM

LKS

LKS

PWR

PWR

LKM

LKM

Multimode

Multimode

Singlemode

Singlemode

TX

TX

RX

RX

TX

TX

RX

RX

Multimode

Multimode

Singlemode

Singlemode

TX

TX

RX

RX

TX

TX

RX

RX

CGETF10xx in the Network . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .2

Operation . . . . . . . . . . . . . . . . . . . . .4

Fault Isolation and Correction . . . . .5

Cable Specifications . . . . . . . . . . . . .6

Technical Specifications . . . . . . . . . .7

Compliance Information . . . . . . . . . .8

CGETF10xx IN THE NETWORK

Install two CGETF10xx series media converters in series to extend, over
fiber, the distance between two 1000BASE-TX devices. Or use one
CGETF10xx media converter to connect a 1000BASE-TX terminal
device and a 1000BASE-SX/LX hub, switch, or router. Or use one
CGETF10xx media converter to connect a 1000BASE-TX hub, switch, or
router and a 1000BASE-SX/LX terminal device.

NOTE: A TRANSITION Networks stand-alone media converter can be installed
in series with a TRANSITION Networks chassis media converter that has a
related model number, such as an SGETF10xx with a CGETF10xx.

INSTALLATION

CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting switch and when installing Slide-in-Module in the
Media Conversion Center. Failure to observe this caution could result in
damage to, and subsequent failure of, the Media Converter Slide-in-Module.

Set 3-Position Jumper

NOTE: Jumper is located on Media Converter Slide-in-Module circuit board.
Use small needle-nosed pliers or similar device to set

jumper. Refer to drawing for jumper positions.
HARDWARE Converter mode is determined by 4-position

switch settings below.
SOFTWARE Converter mode is determined by most-

recently-saved on-board microprocessor settings.

Set 4-Position Switch

NOTE: Switch is located on Media Converter Slide-in-Module circuit board.
Use small flatblade screwdriver or

similar device to set recessed
switches. Refer to drawing for
four-position switch locations.

Full/Half-Duplex Advertisement
(UP=Enabled) Allows full-duplex

mode. (DOWN) Allows half­duplex mode.

Pause Advertisement (UP=Enabled) Allows auto-negotiation pause. (DOWN)
Allows NO auto-negotiation pause.

NOTE: If the Pause feature is present on all network devices attached to the
media converter(s), enable Pause on the media converter(s). Otherwise,
disable Pause on the media converter(s).

LPT (UP=Enabled) Allows a fault EITHER on the copper OR on the fiber side
of the media coverter to stop signal and data transmission on the other side.
(DOWN) Disables LPT.

CATEGORY 5:

Gauge 24 to 22 AWG
Attenuation 22.0 dB /100m @ 100 MHz
Maximum Cable Distance: 100 meters

The Gigabit Ethernet™ network uses all four wire pairs.
The active pairs are pins 1 & 2, pins 3 & 6, pins 4 & 5, and pins 7 & 8. Use only

dedicated wire pairs (such as blue/white & white/blue, orange/white &
white/orange) for the active pins.

NOTE: Straight-through/crossover configuration is automatic.

TECHNICAL SPECIFICATIONS

Standards IEEE 802.3ab, IEEE 802.3 1998
Data Rate 1000 Mb/s

Dimensions 3.4" x 0.86" x 5.0" (86mm x 22mm x 127mm)
Weight 8 oz (approximate)
Delay 300 nsec
Power Consumption 6.5 Watts
Environment Typical Operating Temperature*: 0-50°C (32°to 122°F )

Storage Temperature: -20 to 85°C
Humidity 10-90%, non condensing
Altitude 0-10,000 feet

Warranty Lifetime
*Operating temperature range for this Slide-In-Module depends on the physical

characteristics and the installation configuration of the TRANSITION Networks
chassis in which this Slide-In-Module will be installed. See the User’s Guide for
the chassis in which this Slide-In-Module will be installed for a discussion of
temperature-related installation constraints.

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA
Model: CGETF10xx-100 Series Media Converters
Part Number(s): CGETF1013-100, CGETF1014-100, CGETF1015-100,

CGETF1017-100, CGETF1018-100, CGETF1023-100

Regulation: EMC Directive 89/336/EEC
Purpose: To declare that the CGETF10xx-100to which this declaration refers is

in conformity with the following standards.

EMC-CISPR 22: 1985 Class A&B; EN 55022:1988 Class A&B; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950

I, the undersigned, hereby declare that the equipment specified above conforms to the
above Directive(s) and Standard(s).

_January 6, 2001_____

Stephen Anderson, Vice-President of Engineering Date

SOFTWARE MODE

H

S

HARDWARE MODE

H

S

toward network connectors toward chassis

Not Used

LPT UP=ON

Pause Advertisement UP=ON

Full/Half-Duplex Advertisement UP=ON