Trans Electric WTR3000 User Manual
HDMI Wireless
Incorporates HDMI® technology
Model: WTR-3000
3D, 1080P Wireless HDMI Transmission
Full band IR Extending function
Thank you for purchasing WTR-3000 HDMI Wireless sender. Your satisfaction is very important
to us. WTR-3000 is designed to make the use of your HDTV equipment more comfortable.
WTR-3000 is the ideal product for HD wireless application. Sometime you will find cable
connection is not suitable, long HDMI cable is not available, or cable connection is not an option. You
can use WTR-3000 for you HD wireless application. For example, Home Theater, cross room HD
wireless, meeting room, or game room application.
WTR-3000 is designed with IR extending function. You will find easier remote control experience
with the IR extending function when you try to control your Satellite Receiver, BD player or other
source player.
Features:
Support HDMI 3D format and 1080p wireless transmission.
Transmitter side with HDMI loopthrough output.
Less than 500ms low latency.
Support IR extending function.
HDCP compliant.
Room to room HD wireless transmission.
Up to 30M L.O.S long distance transmission.
Low power consumption.
Contents of Package
WTR-3000 Transmitter main unit *1
WTR-3000 Receiver main unit *1
IR receiver probe *1
IR emitter probe *1
DC 5V/1A power adaptor *2 (MicroUSB type)
User’s Manual *1
INTRODUCTION
FEATURES AND CONTENTS
1
CONNECTION ILLUSTRATION
CONNECTION & OPERATION
Transmitter Box
TOP Front
Back
Receiver Box
TOP Front
Back
2
Connection
Step 1: Use HDMI cable to connect the HDMI IN of WTR-3000 Transmitter to a Source device
Step 2: Use HDMI cable to connect the HDMI OUT of WTR-3000 receiver to a display device (HDTV,
Step 3: Connect the IR emitter to the WTR-3000 Transmitter. And then place the emitter probe in front
Step 4: Connect a DC 5V/1A power adaptor to the Power Jack (MicroUSB) of WTR-3000 Transmitter.
Step 5: Connect another DC 5V/1A power adaptor to the Power Jack (MicroUSB)of WTR-3000
Step 6: Connection Finish. If you can not get image on your display device, please pairing the TX and
(Satellite receiver, CATV STB, BD player, PS3, XBox…) , if you want to watch the source
program on the same time , you can use another HDMI cable connected the HDMI OUT to
display (HDTV).
Projector…)
of the source device’s IR receiver .
Cnect the IR receiver to the WTR-3000 Receiver. And then place the receiver probe in front .
(If you do not need the IR extending function, please skip step 3)
Receiver.
RX first.(Press the MODE key of RX box and then press the MODE key of TX box).
Operation
A. Insatllation
1. Make sure your input AC voltage conforms to the adaptor specifications.
2. Only use the power adaptor provided with the WTR-3000. If you use your own
adaptor, make sure the power output is 5V DC, 1A centre positive.
3. With direct line-of-sight, the maximum range of A/V signal transmission can reach up
to about 100 feet, and this distance would be shortened by obstacles or walls
placed between transmitter and receiver. (The optimum indoor range is under 30M)
4. To ensure good infrared remote control operation aim your remote control at the IR
Probe of the WTR-3000 and press the buttons firmly. ( With some remote controls it may
be necessary to press and hold each button for about a second). The working angle of the
IR Probe is +/- 15 degrees.
5. The remote controller has to be used within the distance of ( from remote control
to receiver )not less than 0.3M and no more than 5M (working angle +/- 15 degrees).
3
Loading...