Page 1
• Lights blue when paired and connected to
your Bluetooth device.
• Blinks blue when not connected to your
Bluetooth device.
• Turns o when the receiver is turned o.
Wirelessly stream music from your iPhone, iPad, or other Bluetooth-enabled device to your
home stereo or other audio device.
Package contents
• Bluetooth Music Receiver • 6 ft. 3.5 mm stereo audio cable
• AC/DC adapter • 3.5 mm jack to RCA stereo audio plug adapter
• Quick Setup Guide
Features
• aptX® audio decoding: The highest Bluetooth stereo audio quality possible
• Supports Near Field Communication (NFC) for easy connection with compatible Bluetooth
devices
• Optical digital audio output: The highest quality audio connection to your home stereo
• Analog stereo audio output: Easily connect to amplied speakers or any device with an audio
input jack
• Wireless range up to 33 feet (10 m)
• Wall mount feature
• Remembers up to eight Bluetooth devices
Note: Music can be played from only one device at a time.
Setting up your Bluetooth Music Receiver
Connecting to an output device
You can choose either analog (good) or digital (best) cables to connect your Bluetooth
Music Receiver, depending on the connections available on your home stereo system.
Digital connection
Using an optical digital audio cable (not included), connect your home stereo system to the
OPTICAL jack on your Bluetooth Music Receiver.
OR
To pair your devices using NFC Fast connection:
Note: Check your Bluetooth device to see if it is compatible with NFC. If it is not, use the steps
above to pair your Bluetooth device.
1 Turn on your receiver by plugging in the AC/DC adapter and sliding the power switch to ON.
The LED indicator blinks on and o slowly. Your receiver is in pairing mode.
2 Turn on Bluetooth on your Bluetooth device.
3 Turn on the NFC function (see documentation that came with your NFC-enabled device).
4 Touch your Smartphone or tablet to the NFC logo ( ) on the top of your receiver, to pair
with your Bluetooth Music Receiver. The LED indicator on the receiver lights blue.
5 When your Smartphone or tablet tells you that the receiver is connected, you can begin
playback.
6 To disconnect, touch your Smartphone or tablet to your Bluetooth Music Receiver again (see
documentation that came with your NFC-enabled device).
Notes:
• Some devices, such as an iPhone, connect immediately after pairing so the LED on the
Bluetooth Music Receiver remains on. Other devices, such as notebook computers, may ask
you if you wish to connect. In this instance, the LED continues to blink until a connection is
established.
• Your Bluetooth Music Receiver saves pairing information for up to eight devices. However, it
can only be connected to and play content from one device at a time.
• When you turn on your Bluetooth Music Receiver, it automatically connects to the last
connected device if that device is in range. To connect to a dierent paired device, you have
to turn o Bluetooth or unpair from the currently paired device and manually connect to
the other paired one.
Analog connection
Using the included 3.5 mm stereo audio cable, connect your home stereo system or other
component to the AUDIO OUT jack on your Bluetooth Music Receiver.
Note: If your home stereo system does not have a 3.5 mm Audio In connector, use the
included 3.5 mm jack to RCA stereo audio plug adapter.
Connecting power:
1 Plug the AC/DC adapter into the DC 5V jack on your receiver.
2 Plug the AC/DC adapter into a wall power outlet and slide the power switch to ON. The LED
indicator begins to blink blue to indicate that the unit is on and ready to be paired to your
Bluetooth devices.
Pairing your devices
Before you can use your Bluetooth Music Receiver with a Bluetooth device, you need to pair
the two. Your receiver can connect to a Bluetooth-enabled device using the Bluetooth settings
on your device or by touching your Bluetooth device to the Bluetooth Music Reciever using
NFC.
To pair your devices using Bluetooth settings:
1 Make sure that a compatible Bluetooth device (like a music player or phone) is turned on
and within 33 feet (10 meters) of your receiver.
2 Turn on your receiver by plugging in the AC/DC adapter and sliding the power switch to ON.
The LED indicator blinks on and o slowly. Your receiver is in pairing mode.
3 Turn on Bluetooth on your Bluetooth device, then set it to pairing mode. For more
information, see the documentation that came with your Bluetooth device.
4 On the Bluetooth device, select Music Receiver in the list of found devices.
5 On the Bluetooth device, enter 0000 as the PIN, if prompted. The LED indicator lights blue
on the receiver.
6 If you are pairing with a computer, make sure that your Bluetooth Music Receiver is
selected as the computer’s default playback device. See the computer’s documentation for
instructions.
LED indicator
QUICK SETUP GUIDE
RF-BTR315 Bluetooth Music Receiver
Final at size 254 mm x 177.8 mm (W x H)
Final fold size 127 mm x 177.8 mm (W x H)
Optical digital audio cable
(not included)
OR
NFC logo
6 ft 3.5 mm stereo audio cable
3.5 mm jack to RCA stereo audio plug adapter
Audio device (such as an audio
receiver)
Before using your new product, please read these instructions to prevent any damage.
v1
R3
Page 2
Reconnecting your device:
When your receiver is not paired to a device, the LED indicator will slowly blink on and o.
Note: The auto connect feature may not work with some Bluetooth devices. If this occurs, use
your Bluetooth device settings menu to manually select the Music Receiver from the list of
found Bluetooth devices.
LED status
V1 ENGLISH 14-1268
Troubleshooting
Indication
Solid blue
Blinks blue
O
Description
Paired and connected to your Bluetooth device.
Not connected to your Bluetooth device.
Turns o when the receiver is turned o.
Legal notices
FCC caution:
Changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
FCC statement:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
Your receiver loses the
Bluetooth connection
if you...
To reconnect…
Turn o your receiver
Move the Bluetooth device
out of range
Turn o your Bluetooth
device
Turn o Bluetooth on your
Bluetooth device
Connect your Bluetooth
device to another
Bluetooth device
Turn on your receiver. Your receiver searches for the last
connected Bluetooth device and reconnects.
Make sure your Bluetooth device is within 33 feet (10 meters)
of your receiver.
Turn on your Bluetooth device, then make sure Bluetooth is
on.
Turn on Bluetooth on your Bluetooth device.
Disconnect your Bluetooth device from the other Bluetooth
device, then set your device to pairing mode. Select Music
Receiver on your Bluetooth device.
• Make sure that your receiver power cord is connected to
your receiver and a power outlet.
• Make sure your receiver is turned on.
• Make sure that your Bluetooth device turned on, Bluetooth
is turned on, and Music Receiver is selected.
• Turn up the volume on your audio device connected to your
Bluetooth Music Receiver.
• Turn up the volume on your Bluetooth device.
• Make sure that your Bluetooth device is not muted.
• Make sure that the cable connections are secure.
• Make sure that your receiver is not paired to another
Bluetooth device.
• Make sure that your Bluetooth device is not paired to
another Bluetooth device.
No sound or low
volume
Cannot establish
Bluetooth connection
No power
Problem: Solutions:
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
RSS-Gen & RSS-210 statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
RSS-102 statement:
This equipment complies with Industry Canada radiation exposure limits set forth for an
uncontrolled environment.
Cet équipement est conforme à l'exposition aux rayonnements Industry Canada limites établies
pour un environnement non contrôlé
One-year limited warranty
Visit www.rocketshproducts.com for details.
Contact Rocketsh:
For customer service, please call 1-800-620-2790.
www.rocketshproducts.com
ROCKETFISH is a trademark of Best Buy and its aliated companies.
Registered in some countries. Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
• Shorten the distance between your receiver and your
Bluetooth device.
• Turn your devices o, then on. Re-pair your receiver and
your Bluetooth device.
• Make sure that your receiver is not paired to another
Bluetooth device.
• Make sure that your receiver and Bluetooth device are both
in pairing mode.
• Make sure that your Bluetooth device is not connected to
any other device.
• Make sure that you have selected Music Receiver on your
Bluetooth device.
• Make sure your device has the NFC feature. See the device's
documentation for instructions.
• Make sure your Bluetooth device is turned on and Bluetooth
is turned on.
• Make sure your NFC device supports Bluetooth pairing with
NFC. Some devices have NFC but may not support Bluetooth
pairing with NFC.
• Make sure the your Bluetooth device is turned on and the
NFC function is turned on.
• When connecting, touch your Bluetooth device to the NFC
logo ( ) on the top of your Bluetooth Music Receiver.
NFC paring does
not work
Problem: Solutions:
My Bluetooth device
keeps unpairing
My Bluetooth Music
Receiver does not
appear on my
Bluetooth device
• Shorten the distance between your receiver and your
Bluetooth device.
• If battery on your Bluetooth device is low, recharge the
battery.
• Shorten the distance between your receiver and your
Bluetooth device.
• Put your receiver into pairing mode, then refresh your list of
Bluetooth devices. For more information, see the
documentation that came with your Bluetooth device.
Loading...