USB
128MB–512MB JetFlash™
User’s Manual
Table of Contents
Introduction
Package Contents.................................................................................... 1
Features .................................................................................................... 1
System Requirements ............................................................................. 2
Before Use ................................................................................................ 2
Driver Installation
Driver Installation for Windows 98SE..................................................... 3
Driver Installation for Windows Me, 2000, and XP ................................ 4
Driver Installation for Mac OS 9.0 or Later............................................. 4
Driver Installation for Linux Kernel 2.4 or Later .................................... 5
Data Storage...................................................................................... 5
Uninstall
................................................................................................. 6
How to Unplug JetFlash Safely
To Remove JetFlash in Windows 98SE.................................................. 7
To Remove JetFlash in Windows Me, 2000, and XP ............................. 7
To Remove JetFlash in Mac OS.............................................................. 7
To Remove JetFlash in Linux ................................................................. 7
Product Overview.......................................................................... 8
Basic Operation
Enter MP3 Mode ....................................................................................... 8
Enter Record Mode .................................................................................. 8
Play a Track .............................................................................................. 9
Pause a Track........................................................................................... 9
Advance to Next Track ............................................................................ 9
Reverse to Previous Track ...................................................................... 9
Fast Forward ............................................................................................ 9
Fast Reverse............................................................................................. 9
Increase Volume ...................................................................................... 9
Decrease Volume ..................................................................................... 9
Repeat a Track ......................................................................................... 9
Repeat All Tracks................................................................................... 10
Repeat a Portion of One Track (AB Repeat) ........................................ 10
Hold......................................................................................................... 10
MP3 Function
To Download or Upload MP3/WMA files .............................................. 10
To Play MP3 Music................................................................................. 11
AB Repeat Function .................................................................. 11
Voice Recording Function
To Record Voice..................................................................................... 11
To Play the Recorded Files ................................................................... 12
LED Indication ................................................................................ 13
Recover JetFlash
To Recover JetFlash in Windows 98SE ............................................... 13
To Recover JetFlash in Windows Me, 2000, and XP ........................... 17
Troubleshooting............................................................................ 23
Specifications................................................................................. 26
Ordering Information................................................................ 26
Warranty
Introduction
Thank you very much for purchasing Transcend’s JetFlash™. This small device is more
than a USB Flash Drive. It combines a USB Flash Drive with MP3, AB repeat, and voice
recording functions. With a USB connector, it can expedite exchanging huge amounts of
data between any desktop or laptop computers with a USB port. With the MP3 function,
you can upload or download music files to or from a PC and use JetFlash as an MP3
player. With the AB repeat function, you can continuously replay a designated section of a
track. With the voice recording function, you can also use JetFlash as a digital recorder. In
addition, JetFlash’s mobility, strong data retention ability, and impressive appearance will
provide you with a brand-new data storage experience.
Package Contents
The JetFlash package includes the following items:
• JetFlash
• AAA battery
• Earphone with neck strap
• Driver CD
• USB extension cable
• Quick Installation Guide
Features
• USB 1.1 compliant and USB 2.0 compatible;
• Expedited Data Transfer: Maximum transfer rate up to 12Mbit/sec at full speed;
• Power Supply: For data transfer, JetFlash is powered directly via the USB port,
and no external power or battery is needed. To use it as an MP3 player or digital
recorder, one AAA battery is necessary. (One AAA alkaline battery can support
up to 12 hours of operation);
• Operating Systems Supported: Windows
Windows® XP, Mac™ OS 9.0 or later, and Linux™ kernel 2.4 or later. Only
®
98SE, Windows® Me, Windows® 2000,
Windows® 98SE needs the enclosed driver;
• MP3 Function: Supports MP3 and WMA formats and so can be used as an MP3
player;
• Supports AB repeat, enabling JetFlash to continuously replay a designated
section of a track;
• Voice Recording Function: Supports WAV format, thus making JetFlash a digital
1
recorder;
• Power Saving Function: Auto-powers off after two minutes without use.
• LEDs indicate the usage status of JetFlash.
System Requirements
Desktop or notebook computer with USB port
One of following operating systems:
• Windows
• Windows
• Windows
• Windows
• Mac OS 9.0 or later
• Linux kernel 2.4 or later
98SE
Me
2000
XP
Before Use
1. Keep JetFlash away from heat, direct sunlight, and moisture. Do not bend, flex, or
drop JetFlash.
2. Make sure the HOLD switch is set to the “OFF” position.
3. Plug or unplug JetFlash by grasping the sides.
4. Never use the “Quick Format” or “Full Format” of Windows to format your
JetFlash.
5. Follow the procedures in “How to Unplug JetFlash Safely” to remove JetFlash from
the system.
2
Driver Installation
Driver Installation for Windows 98SE
1. Put the Driver CD into the CD-ROM (Auto-Run supported). Click Win98 Driver button.
2. Click Next to continue.
3. The Install Shield Wizard guides you through the installation process.
3
4. Plug JetFlash into an available USB port. Your computer automatically detects this
new device. A new Removable Disk drive with a newly assigned drive letter appears
in the My Computer window.
Driver Installation for Windows Me, 2000, and XP
No driver is required. These Windows operating systems have built-in drivers to support
JetFlash. Simply plug JetFlash into an available USB port, and Windows installs the files
needed to use it. A new Removable Disk drive with a newly assigned drive letter appears
in the My Computer window.
Driver Installation for Mac OS 9.0 or Later
No driver is required. Just plug JetFlash into an available USB port and your computer
automatically detects it.
4
Driver Installation for Linux Kernel 2.4 or Later
No driver is required. Just plug JetFlash into the USB port and mount it.
Example: 1. Create directory of /mnt/JetFlash first:
mkdir /mnt/JetFlash
2. mount JetFlash:
mount –a –t msdos /dev/sda1 /mnt/JetFlash
Data Storage
After installing the driver, simply plug JetFlash into an available USB port and you can use
it like a hard drive or other data storage device.
WARNING: To prevent loss of data and/or damage to JetFlash, never remove a
JetFlash from a device while LED is flashing.
WARNING: To prevent the malfunction of JetFlash, never press the PLAY/PAUSE
button while JetFlash is connected with a USB Port.
5
Uninstall
1. Put the Driver CD into the CD-ROM (Auto-Run supported). Click Win98 Driver
button.
2. Click OK to continue.
How to Unplug JetFlash Safely
Before removing JetFlash, please make sure the LED is not flashing! If you
remove JetFlash while the LED is flashing, unpredictable damage to the files or
JetFlash may occur.
When JetFlash is unplugged, it automatically enters MP3 mode. To exit MP3
mode, press and hold the PLAY/PAUSE button until the Power/Play
LED turns off.
6
To Remove JetFlash in Windows 98SE
Unplug JetFlash from your system directly when data are not transferring.
To Remove JetFlash in Windows Me, 2000, and XP
1. Click the icon on the system tray.
2. The Safely remove USB Mass Storage Device pop-up menu will appear. Click to
continue.
3. A message box appears: The ‘USB Mass Storage Device’ device can now be
safely removed from the system.
To Remove JetFlash in Mac OS
Drag and drop the Disk icon corresponding to JetFlash into the trashcan. Then unplug
JetFlash from the USB port.
To Remove JetFlash in Linux
Execute umount /mnt/JetFlash to un-mount the device.
7
Product Overview
REC Button
PLAY/PAUSE Button
Record LED
Power/Play LED
Repeat LED
USB Connector Cover
HOLD Switch
Microphone
Earphone Jack
Track Control Wheel
Volume Control Wheel
Basic Operation
Enter MP3 Mode
1. Disconnect JetFlash from your computer.
2. Press and hold the PLAY/PAUSE button for a few seconds to power on (enter
MP3 mode). The Power/Play LED turns green.
To exit from MP3 mode, press and hold the PLAY/PAUSE button for a few
seconds till the LED turns off.
Enter Record Mode
1. Disconnect JetFlash from your computer.
2. Press and hold the PLAY/PAUSE
button for a few seconds to power on (the
Power/Play LED turns green).
3. Press and hold the REC button for a few seconds to enter Record mode. The
Record LED turns red.
To resume MP3 mode, press and hold the PLAY/PAUSE button until the
Record LED turns off.
8
Play a Track
Press the PLAY/PAUSE button after entering MP3 or Record mode. The
Power/Play LED blinks green and there is track playback.
If there is no track in your JetFlash, the Power/Play LED turns green.
Pause a Track
Press the PLAY/PAUSE button when there is track playback. The Power/Play
LED turns green and the track is paused.
To resume track playback, press the PLAY/PAUSE button again.
Advance to Next Track
Roll the Track Control Wheel toward NEXT . The track advances to the next one.
Reverse to Previous Track
Roll the Track Control Wheel toward the PREV . The track reverses to the
previous one.
Fast Forward
Roll and hold the Track Control Wheel toward NEXT .
Fast Reverse
Roll and hold the Track Control Wheel toward PREV .
Increase Volume
Roll and hold the Volume Control Wheel toward VOL+ until you reach the
desired volume.
Decrease Volume
Roll and hold the Volume Control Wheel toward VOL– until you reach the
desired volume.
Repeat a Track
Press the Track Control Wheel when the Repeat LED is off. The Repeat LED
turns orange.
To resume normal playback, press the Track Control Wheel twice.
9
Repeat All Tracks
Press the Track Control Wheel when the Repeat LED is on, or press the Track
Control Wheel twice when the Repeat LED is off. The Repeat LED blinks
orange.
To resume normal playback, press the Track Control Wheel again.
Repeat a Portion of One Track (AB Repeat)
1. Press the Volume Control Wheel to mark the beginning of the portion you
wish to repeat. The Repeat LED blinks orange.
2. Press the Volume Control Wheel again to mark the end of the portion you
wish to repeat. The Repeat LED blinks orange at a slow speed, and the marked
portion is played as a continuous loop.
Hold
When the HOLD switch is set to the “ON” position, all the buttons and control
wheels are disabled. To enable the buttons and control wheels, the HOLD switch
must be set to “OFF”.
If the HOLD switch is set to “ON”, all LEDs will blink twice when you power on
the JetFlash.
MP3 Function
To Download or Upload MP3/WMA files
1. Complete the driver installation.
2. Plug JetFlash into an available USB port. A new Removable Disk drive with a newly
assigned drive letter appears in the My Computer window. You can now download or
upload MP3/WMA files from or to your computer by clicking and dragging the file
names/icons to the desired directories.
In order to be able to play MP3 or WMA files, you must store them in the root directory
of JetFlash.
JetFlash only supports Mpeg I Layer 3 and WMA files compressed at a rate of 32
Kbps–320Kbps.
10
To Play MP3 Music
1. Make sure you have downloaded MP3 or WMA files to the root directory of your
JetFlash.
2. Disconnect JetFlash from your computer.
3. Connect the earphone with the earphone jack .
4. Set HOLD switch to “OFF” position.
5. Press and hold the PLAY/PAUSE button for a few seconds to power on (enter
MP3 mode). The Power/Play LED turns green.
6. Press the PLAY/PAUSE button again. The Power/Play LED blinks green and
the MP3/WMA files are played back, in alphabetical order.
7. To pause music playback, press PLAY/PAUSE button.
8. To power off, press and hold the PLAY/PAUSE button until the Power/Play
LED turns off.
For more operating instructions, please refer to Basic Operation
AB Repeat Function
Following the procedures below, you can repeat a portion of one track. Make sure the
HOLD switch is set to “OFF”.
1. Enter MP3 mode and play the tracks.
2. Press the Volume Control Wheel to tag the beginning of the portion you wish
to repeat. The Repeat LED blinks orange at fast speed, and music playback
continues.
3. Press the Volume Control Wheel
to repeat. The Repeat LED blinks orange at slow speed, and the tagged portion is
played as a continuous loop.
4. To resume normal playback, press the Volume Control Wheel .
For more operating instructions, please refer to Basic Operation.
again to tag the end of the portion you wish
Voice Recording Function
To Record Voice
1. Disconnect JetFlash from your computer.
2. Set HOLD switch to “OFF” position.
3. Press and hold the PLAY/PAUSE button for a few seconds to power on (enter
MP3 mode). The Power/Play LED turns green.
11
4. Press and hold the REC button for a few seconds to enter Record mode. The
Record LED turns red.
5. Press the REC button. The Record LED blinks red and voice recording starts.
6. Press the REC button to stop voice recording when you wish to stop.
7. Press the REC button to start voice recording when you wish to start again.
The recorded files (VXXX.WAV format) are saved on the folder “Voice”, in an
ascending order.
With sufficient power: 128MB memory can store up to 9 hours of recorded voice.
256MB memory can store up to 18 hours of recorded voice.
512MB memory can store up to 36 hours of recorded voice.
To achieve better quality recording, please keep voice source close to the microphone
of JetFlash.
If JetFlash is full and there is no memory available for voice recording, the
Power/PLAY LED turns on. To make memory available for voice recording, delete
some files or folders from JetFlash.
To resume MP3 mode, press and hold PLAY/PAUSE button until the Record
LED turns off.
To Play the Recorded Files
1. Disconnect JetFlash from your computer.
2. Set HOLD switch to “OFF” position.
3. Press and hold the PLAY/PAUSE button for a few seconds to power on (enter
MP3 mode). The Power/Play LED turns green.
4. Press and hold the REC button for a few seconds to enter Record mode. The
Record LED turns red.
5. Press the PLAY/PAUSE button to play the recorded files. The Power/Play
LED blinks green.
To resume MP3 mode, press and hold PLAY/PAUSE button until the Record
LED turns off.
To power off, press and hold the PLAY/PAUSE button until the Power/Play
LED turns off.
For more operating instructions, please refer to Basic Operation.
12
LED Indication
Record LED
(Red)
off off off Power off
off fast blink off
off on off Power on (in MP3 mode)
off normal blink off Play MP3 music
off normal blink on
off normal blink normal blink
off normal blink fast blink
off normal blink slow blink
on on off
normal blink off off
on normal blink off
on normal blink on
on normal blink normal blink
Power/Play LED
(Green)
Repeat LED
(Orange)
Data transfer
Repeat a track
Repeat all tracks
The beginning of the portion you wish to
repeat is marked in MP3 mode
Repeat a portion of one track
In Record mode
Record voice
Play the recorded file(s)
Repeat a recorded file
Repeat all recorded files
Status
on normal blink fast blink
on normal blink slow blink
The beginning of the portion you wish to
repeat is marked in Record mode
Repeat a portion of one recorded file
Recover JetFlash
If your JetFlash is ever damaged, you can use the Recovery program to restore its
default settings.
Running the Recovery program will erase all the data on the JetFlash.
If there are bad blocks in the flash memory chip of JetFlash, the memory size of
JetFlash after running the Recovery program will be smaller than the original
memory size.
To Recover JetFlash in Windows 98SE
1. Put the Driver CD into the CD-ROM (Auto-Run supported).
2. Remove the battery from JetFlash.
3. Press and hold the PLAY/PAUSE button, then plug JetFlash into an available
USB port.
13
Do not release the PLAY/PAUSE button until the Recovery procedures are
completed.
4. Found New Hardware and New Hardware Found messages appear. (Only the first
time you recover the JetFlash.)
5. Click the Recovery button on the JetFlash splash screen.
6. MSCN Format status bar message appears.
If above message does not appear, click the Recovery button on the JetFlash splash
14
screen again. If this still doesn’t work, press and hold PLAY/PAUSE button to
re-plug JetFlash first. Then, click the Recovery button on the JetFlash splash screen
again.
7. New Hardware Found messages appear. (Only the first time you run the Recovery
program.)
8. Click the Recovery button on the JetFlash windows splash screen again.
9. MSCN Format dialog box appears. Make sure that the Quick format checkbox
15
remains unchecked. Click Start to initiate the low-level format.
10. Complete message appears. Click Close to complete the Recovery procedures.
11. Release the PLAY/PAUSE button. JetFlash has been returned to its initial
status for your usage.
16
To Recover JetFlash in Windows Me, 2000, and XP
Skip steps 1-3 if the Utility program has already been installed.
1. Put the Driver CD into the CD-ROM (Auto-Run supported) and click the Utility button
on the JetFlash splash screen.
2. SigmaTel MSCN Audio Player Setup window appears. Click Next to continue.
3. The InstallShield Wizard guides you through the Utility installation.
4. Remove the battery from JetFlash.
17
5. Press and hold the PLAY/PAUSE button, then plug JetFlash into an available
USB port.
Do not release the PLAY/PAUSE button until the Recovery procedures are
completed.
6. Found New Hardware messages appear. (Only the first time you recover the
JetFlash.)
If using Windows Me or 2000, go directly to step 9.
7. Wait a while until Found New Hardware Wizard windows appears. Click Next to
continue. (Only appears the first time you recover the JetFlash.)
18
8. Found New Hardware Wizard window appears. Click Finish to continue. (Only
appears the first time you recover the JetFlash.)
9. Click the Recovery button on the JetFlash splash screen.
10. MSCN Format status bar message appears.
If above message does not appear, click the Recovery button on the JetFlash
splash screen again. If this still doesn’t work, press and hold PLAY/PAUSE
button to re-plug JetFlash first. Then, click the Recovery button on the
JetFlash splash screen again.
11. Found New Hardware messages appear. (Only appears the first time you run the
Recovery program.)
19
If using Windows Me or 2000, go directly to step 15.
12. Found New Hardware Wizard window appears. Click Next to continue. (Only
appears the first time you run the Recovery program.)
13. Found New Hardware Wizard window appears. Click Next to continue. (Only
appears the first time you run the Recovery program.)
20
14. Completing the Found New Hardware Wizard message appears. Click Finish to
continue. (Only appears the first time you run the Recovery program.)
15. MSCN Format dialog box appears. Click Start in the Media Recovery tab to initiate
the low-level format.
21
16. Complete message box appears. Click Close to complete the Recovery procedures.
17. Release the PLAY/PAUSE
status for your usage.
22
button. JetFlash has been returned to its initial
Troubleshooting
Q1: Why doesn’t the driver CD Auto-Run after it is inserted into the CD-ROM drive in
Windows?
A1: This problem usually occurs because the Auto-Insert function of the CD-ROM drive
is disabled. Please enter Device Manager in Control Panel and enable the
Auto-Insert function of the CD-ROM drive. Alternatively, you can execute the
JetFlash.EXE in the driver CD manually.
Q2: Why isn’t my operating system detecting JetFlash after I’ve plugged it into the USB
port of my computer?
A2: Please check following:
1. Is the driver installation complete? If not, follow the procedures in Driver
Installation to complete it.
2. Is JetFlash properly connected to the USB port? If not, unplug it and plug it in
again.
3. Is the USB port enabled? If not, refer the user’s manual of your computer (or
motherboard) to enable it.
Q3: Why can’t MP3 or WMA files be downloaded to JetFlash?
A3: This problem may be caused by an incomplete driver installation. Uninstall the driver
and re-install it. If it doesn’t work, see Recover JetFlash to format JetFlash.
Q4: Why can’t I find the file that was just copied to JetFlash? Why does the file that was
just deleted still appear?
A4: This problem occurs when the copy or delete process had not been completed
before you unplugged JetFlash. Please re-copy or re-delete the file and follow the
procedure shown in How to Unplug JetFlash Safely to remove JetFlash after the
copy or delete process is completed.
Q5: Why does the Power/Play LED turn green after I have unplugged JetFlash from my
computer?
A5: This situation is normal. Whenever JetFlash is unplugged from a computer, it enters
MP3 mode automatically. To exit from MP3 mode, press and hold the PLAY/PAUSE
button until the Power/Play LED turns off.
Q6: Why don’t the buttons work during the operation of JetFlash?
A6: Check to see if the Hold switch is set to “ON”. If yes, set it to “OFF”.
23
Q7: Why do the three LEDs just blink a moment and extinguish when press the
PLAY/PAUSE button to turn on JetFlash?
A7: Please press and hold the PLAY/PAUSE button a second or two longer, until the
three LEDs blink once and the Power/Play LED turns green. If the problem persists,
please check to see whether the battery power is used up. If it is, replace the battery
with a new one.
Q8: Why can’t I turn on JetFlash and start playing MP3 music or recording voice?
A8: Please check following:
1. Is JetFlash connected to your computer? If yes, unplug it.
2. Is the Hold switch set to “ON”? If yes, set it to “OFF”.
3. Is the battery inserted in the right direction? If not, reverse the battery.
4. Is the battery power used up? If yes, replace it with a new one.
Q9: Why can’t I hear track playback after pressing the PLAY/PAUSE button?
A9: Please check following:
1. Are there any MP3 or WMA files in the root directory of JetFlash? If not, you
must download music files from your computer or Internet first. (Only Mpeg I
Layer 3 and WMA files compressed at a rate of 32Kbps–320Kbps are
supported.)
2. Is the earphone properly connected to the earphone jack? If not, connect it
again.
3. Is the volume loud enough? If not, roll and hold the Volume Control Wheel
toward VOL+ until the music playback can be heard.
Q10: Why does the track playback sound intermittent?
A10: This problem usually occurs when the earphone is not properly connected to the
earphone jack. Plug the earphone into the earphone jack again to make sure they
are properly connected.
Q11: Why does the volume become softer and softer? When I roll the Volume Control
Wheel to increase the volume, my JetFlash turns off.
A11: This problem occurs when battery power is too low. Please replace the battery with
a new one.
Q12: Why does the Power/Play LED turn on when recording voice and then JetFlash
turns off 2 minutes later?
A12: JetFlash is full and there is no memory available for voice recording. To make
memory available for voice recording, delete some files or folders from JetFlash.
24
Q13: Why does JetFlash turn off automatically after entering MP3 mode or Record
mode?
A13: JetFlash features a power-save function. If your JetFlash is idle for two minutes,
power-save is triggered and the power turns off automatically.
Q14: Why is JetFlash automatically removed from the operating system when I use it as
a USB Flash Drive?
A14: This problem occurs when you press the PLAY/PAUSE button while
JetFlash is connected with a USB port. Please unplug JetFlash from the USB port
then re-plug it.
Q15: Why are the “Modified” times of voice files all the same?
A15: Because of the limitations of the controller circuitry, JetFlash does not have a clock
for use in recording file creation or save time. To better distinguish files from each
other, you can rename them.
Q16: Why can’t the MP3 and voice recording functions work after I’ve formatted
JetFlash using the “Quick Format” or “Full Format” option in Windows?
Q16: Formatting JetFlash using the “Quick Format” or “Full Format” option of Windows
destroys the default format of JetFlash. To retrieve the default format, you must
link to http://www.transcend.com.tw/English to download and update the
JetFlash firmware.
25
Specifications
• Size: 97 mm × 31 mm × 18 mm
• Weight: 25 g (without battery)
• Data retention: Up to 10 years
• Shock resistance: 1000 G (maximum)
• Erase cycles: 1,000,000 times
• Signal-to-Noise Ratio: 90dB
• Output frequency: 20Hz–20KHz
• Estimated battery life: 12 hours (alkaline battery)
• MP3 format: MP3 and WMA
• Record format: ADPCM (WAV)
• Compress rate: 32Kbps–320Kbps
• Speed: Read 7.2 Mbit/sec, Write 5.8 Mbit/sec
• Certificates: CE, FCC, BSMI
Ordering Information
Memory Size Transcend P/N
128MB TS128MJFLASHM
256MB TS256MJFLASHM
512MB TS512MJFLASHM
26
JetFlash Limited Warranty
“Above and beyond” is the standard we set ourselves for customer
service at Transcend. We consistently position ourselves to be
significantly above the industry norm. It’s all part of our commitment to
Customer Satisfaction.
All Transcend Information, Inc. (Transcend) products are warranted and tested
to be free from defects in material and workmanship and to conform to the
published specifications. Should your Transcend JetFlash malfunction during
normal use in its recommended environment due to improper workmanship or
materials within the warranty period, Transcend will repair or replace your
product with a comparable product. This warranty is subject to the conditions
and limitations set forth herein.
Duration of Warranty: Transcend JetFlash are covered by this warranty for a
period of two (2) years from the date of purchase. Transcend will inspect the
product and make the determination as to whether the product is eligible for
repair or replacement. The decision by Transcend regarding eligibility of the
product for repair or replacement will be final and binding. Transcend reserves
the right to provide a functionally equivalent refurbished replacement product.
Limitations: This warranty does not apply to products that fail due to accident,
abuse, mishandling, improper installation, alteration, and acts of nature,
improper usage, or problems with electrical power. Transcend JetFlash must be
used with devices that conform to the recommended industry standards.
Transcend will not be liable for damages resulting from a third party device that
causes the Transcend product to fail. Transcend shall in no event be liable for
any consequential, indirect, or incidental damages, lost profits, lost business
investments, lost goodwill, or interference with business relationships as a result
of lost data. Transcend is also not responsible for damage or failure of any third
party equipment, even if Transcend has been advised of the possibility. This
limitation does not apply to the extent that it is illegal or unenforceable under
applicable law.
Disclaimer: The foregoing limited warranty is exclusive, with no other
warranties, implied or statutory, including, but not limited to any implied
warranty of merchantability or fitness for a particular purpose. This warranty is
not affected in any part by Transcend providing technical support or advice.
Transcend Information, Inc.
www.transcendusa.com
The Transcend logo is a registered trademark of Transcend Information, Inc.
*All logos and marks are trademarks of their respective companies.
Loading...