Trane TUD2B060AFV32A, TUD2B080AFV32A, TUD2B100AFV32A, TUD2C080AFV42A, TUD2D120AFV52A User Manual

Upflow/Horizontal 80%
2-Stage, Variable Speed
Gas-Fired Furnace with
Whole House Air Cleaner

XV80i

TUD2B060AFV32A, TUD2B080AFV32A,
TUD2C080AFV42A, TUD2B100AFV32A,
TUD2D120AFV52A

© 2009 Trane All Rights Reserved

PUB. NO. 22-1802-03

Features Summary

WHOLE HOUSE AIR CLEANER

The Whole House Air Cleaner uses
advanced technology to remove up to

99.98% of allergens from the filtered
air and removes particles down to .3
microns in size. Cleaning intervals of
1-3 months are typical, depending on
the home environment.

NATURAL GAS MODELS

Central Heating furnace designs are
certified by the American Gas
Association for both natural and L.P.
gas. Limit setting and rating data
were established and approved under
standard rating conditions using
American National Standards
Institute standards.

SAFE OPERATION

The Integrated System Control has
solid state devices, which continuously
monitor for presence of flame, when
the system is in the heating mode of
operation. Dual solenoid combination
gas valve and regulator provide extra
safety.

QUICK HEATING

Durable, cycle tested, heavy gauge
aluminized steel heat exchanger
quickly transfers heat to provide warm
conditioned air to the structure. Low
energy power vent blower, to increase
efficiency and provide a positive
discharge of gas fumes to the outside.

BURNERS

Multiport In-shot burners will give
years of quiet and efficient service. All
models can be converted to L.P. gas.

INTEGRATED SYSTEM CONTROL

Exclusively designed operational
program provides total control of
furnace limit sensors, blowers, gas
valve, flame control and includes self
diagnostics for ease of service. Also
contains connection points for
humidifier.

AIR DELIVERY

The variable speed, direct drive
blower motor, has sufficient airflow
for most heating and cooling
requirements, will switch from
heating to cooling speeds on demand
from room thermostat. The blower
door safety switch will prevent or
terminate furnace operation when the
blower door is removed.

STYLING

Heavy gauge steel and “wrap-around”
cabinet construction is used in the
cabinet with baked-on enamel finish
for strength and beauty. The heat
exchanger section of the cabinet is
completely lined with foil faced
fiberglass insulation. This results in
quiet and efficient operation due to
the excellent acoustical and
insulating qualities of fiberglass.
Built-in bottom pan and bottom
return air connection.

FEATURES AND GENERAL
OPERATION

The XV80i High Efficiency Gas
Furnaces employ a Hot Surface
Ignition system, which eliminates the
waste of a constant burning pilot.
The integrated system control lights
the main burners upon a demand for
heat from the room thermostat.
Complete front service access.

a. Low energy power venter
b. Vent proving pressure switch.

PUB. NO. 22-1802-03

2

Contents

Feature Summary

Features and Benefits

Standard Equipment
Optional Equipment

General Data

TUD2B060AFV32A
TUD2B080AFV32A
TUD2C080AFV42A
TUD2B100AFV42A
TUD2D120AFV52A

Performance Data

Electric Data

Field Wiring Diagrams

Dimensions

22

2

22

44

4

44

66

6

66

88

8

88

1313

13

1313

1515

15

1515

2020

20

2020

PUB. NO. 22-1802-03

3

Features
and Benefits

XV80i STANDARD EQUIPMENT

•Whole House Air Cleaner

•Upflow/Horizontal

•Power supply 115/1/60

•2-stage gas valve

•2-speed venter

•Variable speed ECM blower motor

•Silicon Nitride hot surface igniter with
adaptive heat up

•Integrated solid state control

•Attractive color accents

•Heavy gauge aluminized steel heat
exchanger

•Multi-port In-shot burners

•Complete front service access

•Alternate bottom/left/right return air

•Slide out blower assembly

• Hinged blower door

•Perfect fit door catches

•Insulated bower door

•Gasketed blower door

•Two tone color

•Integrated solid state control with
self-diagnostics

•Common vent capability

•Optional L.P. conversion kit

• Left/right gas connection

•Accessory hook-up capability

•Selectable cooling fan off delay elimi­nates need for BAY24X045time delay
kit

• Enhanced cooling control

PUB. NO. 22-1802-03

4

Features
and Benefits

XV80i OPTIONAL EQUIPMENT

Thermostat, Mechanical 2-Stage Heating/ 1-Stage Cooling ............................................................................... TAYSTAT241 [ ]

Thermostat, Mechanical Heating Only With Fan Switch .................................................................................. BAYSTAT303 [ ]

Thermostat, Mechanical Heating Only ............................................................................................................... BAYSTAT388 [ ]

Thermostat, Heating/Cooling Single Stage (Mounts Horizontally) ........................................................................ AY28X092 [ ]

Thermostat,

Thermostat, Electronic Programmable (5-2) 1-Stage Heating/1-Stage Cooling ............................................... BAYSTAT340 [ ]

Thermostat, Heating/Cooling Single Stage (Mounts Vertically) ........................................................................ BAYSTAT305 [ ]

Thermostat, Electronic Programmable 2-Stage Heating/2-Stage Cooling ..................................................... TAYSTAT302C [ ]

Thermostat, Electronic Programmable 1-Stage Heating/1-Stage Cooling ..................................................... TAYSTAT300C [ ]

Propane Conversion Kit .................................................................................................................................... BAYLPKT210A [ ]

Coil Enclosure (17-1/2” Wide Cabinets) ............................................................................................................. BAYCLE1700 [ ]

Coil Enclosure (21” Wide Cabinets) ................................................................................................................... BAYCLE2100 [ ]

Coil Enclosure (24-1/2” Wide Cabinets) ............................................................................................................. BAYCLE2400 [ ]

High Altitude Switch ........................................................................................................................................... BAYHALT249 [ ]

Masonry Chimney Vent Kit .............................................................................................................................. BAYVENT800B [ ]

Electronic Non-programmable 1-Stage Heating/1-Stage Cooling .......................................... BAYSTAT370 [ ]

5

PUB. NO. 22-1802-03

General
Data

MODEL
TYPE
RATINGS

1st Stage Input BTUH

2nd Stage Input BTUH

Temp. rise (Min.-Max.) °F.

BLOWER DRIVE

Diameter - Width (In.)
No. Used
Speeds (No.)
CFM vs. in. w.g.
Motor HP
R.P.M.
Volts / Ph / Hz

COMBUSTION FAN — Type

Drive - No. Speeds
Motor HP - RPM
Volts / Ph / Hz
FLA

FILTER — Furnished?

Type
Max. Indoor Relative Humidity

VENT — Size (In.)
HEAT EXCHANGER

Type -Fired

Gauge (Fired)

ORIFICES — Main

Nat. Gas. Qty. — Drill Size
L.P. Gas Qty. — Drill Size

GAS VALVE
PILOT SAFETY DEVICE

Type

BURNERS — Type

Number

POWER CONN. — V / Ph / Hz

Ampacity (In Amps)
Max. Overcurrent Protection (Amps)

PIPE CONN. SIZE (In.)
DIMENSIONS

Crated (In.)
Uncrated (In.)

WEIGHT

Shipping (Lbs.) / Net (Lbs.)

2

1st Stage Capacity BTUH (ICS)

2nd Stage Capacity BTUH (ICS)

-Unfired

3

3

5

4

Product Specifications

*UD2B060AFV32A

Upflow / Horizontal

39,000
31,200
60,000
48,000
30 - 60

Direct
10 x 7

1

Variable

See Airflow Table

1/2

Variable

115/1/60

Centrifugal

Direct - 2

1/100 - 2543/1727

115/1/60

0.70/0.40
Yes

Whole House Air Cleaner

65%

4 Round

Alum. Steel - Type 1

20

3 — 45
3 — 56

Redundant - Two Stage

Hot Surface Ignition

Multi-port In-shot

3

115/1/60

10.5
15

1/2

H x W x D

41-3/4 x 19-1/2 x 30-1/2

40 x 17-1/2 x 28-1/2

136 / 126

1

*UD2B080AFV32A

Upflow / Horizontal

52,000
41,600
80,000
64,000
30 - 60

Direct
10 x 7

1

Variable

See Airflow Table

1/2

Variable

115/1/60

Centrifugal

Direct - 2

1/100 - 2543/1727

115/1/60

0.70/0.40
Yes

Whole House Air Cleaner

65%

4 Round

Alum. Steel - Type 1

20

4 — 45
4 — 56

Redundant - Two Stage

Hot Surface Ignition

Multi-port In-shot

4

115/1/60

10.5
15

1/2

H x W x D

41-3/4 x 19-1/2 x 30-1/2

40 x 17-1/2 x 28-1/2

142 / 132

*UD2C080AFV42A

Upflow / Horizontal

52,000
41,600
80,000
64,000
30 - 60

Direct

10 x 10

1

Variable

See Airflow Table

3/4

Variable

115/1/60

Centrifugal

Direct - 2

1/100 - 2543/1727

115/1/60

0.70/0.40
Yes

Whole House Air Cleaner

65%

4 Round

Alum. Steel - Type 1

20

4 — 45
4 — 56

Redundant - Two Stage

Hot Surface Ignition

Multi-port In-shot

4

115/1/60

12.9
20

1/2

H x W x D

41-3/4 x 23 x 30-1/2

40 x 21 x 28-1/2

166 / 155

1 Central Furnace heating designs are certified by AGA and CSA.
2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applications, above input

ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above sea level.

3 Based on U.S. government standard tests.
4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.
5 The FIELD CHARGER may require more frequent cleaning in homes with high indoor relative humidity (greater than 65% RH). Consult your service professional about cleaning

intervals.

PUB. NO. 22-1802-03

6

General
Data

MODEL
TYPE
RATINGS

1st Stage Input BTUH

2nd Stage Input BTUH

Temp. rise (Min.-Max.) °F.

BLOWER DRIVE

Diameter - Width (In.)
No. Used
Speeds (No.)
CFM vs. in. w.g.
Motor HP
R.P.M.
Volts / Ph / Hz

COMBUSTION FAN — Type

Drive - No. Speeds
Motor HP - RPM
Volts / Ph / Hz
FLA

FILTER — Furnished?

Type
Max. Indoor Relative Humidity

VENT — Size (In.)
HEAT EXCHANGER

Type -Fired

Gauge (Fired)

ORIFICES — Main

Nat. Gas. Qty. — Drill Size
L.P. Gas Qty. — Drill Size

GAS VALVE
PILOT SAFETY DEVICE

Type

BURNERS — Type

Number

POWER CONN. — V / Ph / Hz

Ampacity (In Amps)
Max. Overcurrent Protection (Amps)

PIPE CONN. SIZE (In.)
DIMENSIONS

Crated (In.)
Uncrated (In.)

WEIGHT

Shipping (Lbs.) / Net (Lbs.)

2

1st Stage Capacity BTUH (ICS)

2nd Stage Capacity BTUH (ICS)

-Unfired

3

3

5

4

Product Specifications

*UD2B100AFV32A

Upflow / Horizontal

65,000
52,000

100,000

80,000
40 - 70

Direct
10 x 7

1

Variable

See Airflow Table

1/2

Variable

115/1/60

Centrifugal

Direct - 2

1/75 - 2708/1868

115/1/60

0.87/0.49
Yes

Whole House Air Cleaner

65%

4 Round

Alum. Steel - Type 1

20

5 — 45
5 — 56

Redundant - Two Stage

Hot Surface Ignition

Multi-port In-shot

5

115/1/60

10.8
15

1/2

H x W x D

41-3/4 x 19-1/2 x 30-1/2

40 x 17-1/2 x 28-1/2

142 / 132

1

*UD2D120AFV52A

Upflow / Horizontal

78,000
62,400

120,000

97,000
35 - 65

Direct

10 x 10

1

Variable

See Airflow Table

1

Variable

115/1/60

Centrifugal

Direct - 2

1/60 - 3090/2225

115/1/60

1.14/0.51
Yes

Whole House Air Cleaner

65%

4 Round

Alum. Steel - Type 1

20

6 — 45
6 — 56

Redundant - Two Stage

Hot Surface Ignition

Multi-port In-shot

6

115/1/60

15.3
20

1/2

H x W x D

41-3/4 x 26-1/2 x 30-1/2

40 x 24-1/2 x 28-1/2

193 / 181

1 Central Furnace heating designs are certified by AGA and CSA.
2 For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applications, above input

ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above sea level.

3 Based on U.S. government standard tests.
4 The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.
5 The FIELD CHARGER may require more frequent cleaning in homes with high indoor relative humidity (greater than 65% RH). Consult your service professional about cleaning

intervals.

7

PUB. NO. 22-1802-03

Performance
Data

*UD2B060AFV32A Furnace Heating Airflow (CFM) and Power (watts) vs. External Static Pressure With Filter

Heating

1st Stage

Heating

Heating

2nd

Stage

Airflow
Setting

Low

Medium**

High

Low

Medium**

High

Dip Switch Setting External Static Pressure

SW7 SW8 0.1 0.3 0.5 0.7 0.9

CFM 583 590 625 622 620

ON

ON

Temp. Rise 50 49 46 46 47

Watts 60 87 126 157 192

CFM 635 687 701 695 694

ON

OFF

Temp. Rise 45 42 41 42 42

Watts 69 110 148 183 221

CFM 746 778 803 819 823

OFF

OFF

Temp. Rise 39 37 36 35 35

Watts 97 140 185 230 272

CFM 779 816 848 866 874

ON

ON

Temp. Rise 57 54 52 51 51

Watts 104 152 201 255 302

CFM 872 939 964 976 985

ON

OFF

Temp. Rise 51 47 46 46 45

Watts 136 203 264 312 365

CFM 1069 1102 1102 1110 1078

OFF

OFF

Temp. Rise 42 40 40 40 41

Watts 227 293 345 403 429

Unit

Outdoor

1.5

2

2.5

Cooling

3** OFF OFF

Notes:

1. * First letter may be "A" or "T".

2. ** Factory setting.

3. Continuous Fan Setting: Heating or cooling airflow is approximately 50% of selected cooling value.

4. For variable speed low speed airflows are approximately 30% of listed values.

5. LOW 350 cfm/ton is recommended for variable speed application for COMFORT & HUMID CLIMATE setting; NORMAL is 400 cfm/ton;
HIGH 450 cfm/ton is for DRY CLIMATE setting.

PUB. NO. 22-1802-03

*UD2B060AFV32A Furnace Cooling Airflow (CFM) and Power (Watts) vs. External Static Pressure With Filter
Airflow
Setting

Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal**

(400

High (450

CFM/ton)

SW1 SW2 SW3 SW4 0.1 0.3 0.5 0.7 0.9

ON

ON

ON ON

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

OFF

Dip Switch Setting External Static Pressure

ON

ON

ON OFF

OFF

OFF

OFF ON

OFF ON

OFF

ON

OFF

OFF

OFF

ONOFFON

OFF

OFFONON

ON

OFFOFF

OFF

ONOFFOFF

OFF

OFFONOFF

CFM 517 535 538 546 542

Watts 49 76 105 141 171

CFM 587 594 629 622 618

Watts 61 89 129 159 196

CFM 642 677 705 701 696

Watts 73 109 151 185 222

CFM 676 705 729 736 738

Watts 79 118 159 198 240

CFM 776 814 833 863 867

Watts 103 150 200 251 298

CFM 870 928 961 974 975

Watts 137 198 259 316 361

CFM 831 883 915 935 941

Watts 122 182 238 292 345

CFM 1023 1052 1055 1061 1048

Watts 203 266 316 370 413

CFM 1156 1174 1188 1196 1085

Watts 280 351 415 482 442

CFM 1063 1094 1090 1100 1070

Watts 226 290 344 397 430

CFM 1214 1241 1263 1234 1123

Watts 320 395 476 514 469

CFM 1399 1409 1377 1278 1164

Watts 486 575 604 559 507

8

Performance
Data

*UD2B080AFV32A Furnace Heating Airflow (CFM) and Power (watts) vs. External Static Pressure With Filter

Heating

1st Stage

Heating

Heating

2nd

Stage

Airflow
Setting

Low

Medium**

Low

Medium** ON

High OFF

Dip Switch Setting External Static Pressure

SW7 SW8 0.1 0.3 0.5 0.7 0.9

CFM 846 852 836 811 810

ON

ON

Temp. Rise 46 45 46 48 48

Watts 127 167 200 229 270

CFM 969 956 936 915 897

ON

OFF

Temp. Rise 40 40 41 42 43

Watts 182 218 251 283 317

CFM 1126 1116 1108 1095 1074

OFFHigh

OFF

Temp. Rise 34 35 35 35 36

Watts 270 316 361 404 441

CFM 1216 1205 1189 1169 1111

ON

ON

Temp. Rise 49 49 50 51 53

Watts 333 383 429 468 473

CFM 1362 1347 1324 1254 1145

OFF

Temp. Rise 44 44 45 47 52

Watts 468 518 559 550 500

CFM 1474 1419 1370 1258 1148

OFF

Temp. Rise 40 42 43 47 52

Watts 590 601 609 558 506

Unit

Outdoor

2.5

3

Cooling

3.5**

Notes: rpm 1192 1239 1285 1303 1315

1. * First letter may be "A" or "T".

2. ** Factory setting.

3. Continuous Fan Setting: Heating or cooling airflow is approximately 50% of selected cooling value.

4. For variable speed low speed airflows are approximately 30% of listed values.

5. LOW 350 cfm/ton is recommended for variable speed application for COMFORT & HUMID CLIMATE setting; NORMAL is 400 cfm/ton;
HIGH 450 cfm/ton is for DRY CLIMATE setting.

*UD2B080AFV32A Furnace Cooling Airflow (CFM) and Power (Watts) vs. External Static Pressure With Filter

Airflow

Setting

Low (350

CFM/Ton)

Normal (400

CFM/ton)
High (450
CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)
High (450
CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)
High (450
CFM/ton)

SW1 SW2 SW3 SW4 0.1 0.3 0.5 0.7 0.9

OFF

OFF ON OFF OFF

OFF ON

ON

ON

ON

OFF

OFF

OFF

Dip Switch Setting External Static Pressure

ON

OFF

OFF OFF

OFF ON

OFF ON

ON OFF

OFF

ONOFFOFF

OFF

OFFONOFF

ON

OFFOFFOFF

OFF

CFM 934 926 913 889 863

Watts 162 201 236 267 296

CFM 1063 1051 1042 1029 1008

Watts 228 272 315 356 394

CFM 1220 1212 1199 1179 1119

Watts 334 386 433 471 475

CFM 1131 1122 1111 1101 1083

Watts 269 317 361 405 442

CFM 1310 1295 1273 1246 1136

Watts 405 457 498 535 490

CFM 1458 1420 1369 1266 1154

Watts 569 599 606 561 506

CFM 1329 1310 1287 1253 1142

Watts 424 472 516 542 493

CFM 1475 1422 1369 1272 1158

Watts 585 596 605 563 510

CFM 1473 1421 1367 1269 1152

Watts 585 595 605 558 505

9

PUB. NO. 22-1802-03

Performance
Data

*UD2C080AFV42A Furnace Heating Airflow (CFM) and Power (watts) vs. External Static Pressure With Filter

Heating

1st Stage

Heating

Heating

2nd

Stage

Airflow

Setting

Low

Medium** ON

High

Low

Medium**

High OFF

Dip Switch Setting External Static Pressure

SW7 SW8 0.1 0.3 0.5 0.7 0.9

CFM 745 758 758 761 735

ON

ON

Temp. Rise 52 51 51 51 52

Watts 68 111 153 197 231

CFM 839 864 851 851 822

OFF

Temp. Rise 46 45 45 45 47

Watts 87 134 181 224 263

CFM 934 961 943 941 933

OFF

OFF

Temp. Rise 41 40 41 41 41

Watts 110 164 211 263 310

CFM 1064 1077 1085 1086 1077

ON ON

Temp. Rise 56 55 55 55 55

Watts 152 205 262 325 379

CFM 1197 1226 1241 1230 1229

ON

OFF

Temp. Rise 50 48 48 48 48

Watts 201 271 338 395 462

CFM 1345 1375 1376 1371 1320

OFF

Temp. Rise 44 43 43 43 45

Watts 272 348 418 480 517

Unit

Outdoor

2.5

3

3.5

Cooling

Notes:

1. * First letter may be "A" or "T".

2. ** Factory setting.

3. Continuous Fan Setting: Heating or cooling airflow is approximately 50% of selected cooling value.

4. For variable speed low speed airflows are approximately 30% of listed values.

5. LOW 350 cfm/ton is recommended for variable speed application for COMFORT & HUMID CLIMATE setting; NORMAL is 400 cfm/ton;
HIGH 450 cfm/ton is for DRY CLIMATE setting.

*UD2C080AFV42A Furnace Cooling Airflow (CFM) and Power (Watts) vs. External Static Pressure With Filter
Airflow
Setting

Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal**

(400

High (450

CFM/ton)

SW1 SW2 SW3 SW4 0.1 0.3 0.5 0.7 0.9

ON

ON

ON

OFF

OFF

OFF

ON

ON

ON

OFF OFF OFF

OFF OFF ON

Dip Switch Setting External Static Pressure

CFM 840 862 850 846 824

Watts 87 135 182 223 264

CFM 962 977 974 973 965

Watts 118 167 221 276 320

CFM 1076 1095 1104 1102 1096

Watts 153 212 271 331 390

CFM 1004 1018 1016 1019 1007

Watts 130 183 236 297 343

CFM 1143 1176 1187 1184 1180

Watts 180 267 311 368 436

CFM 1303 1334 1337 1334 1296

Watts 252 326 394 456 502

CFM 1167 1193 1208 1196 1193

Watts 190 255 321 378 443

CFM 1356 1378 1383 1358 1321

Watts 279 355 424 473 518

CFM 1521 1528 1537 1537 1344

Watts 379 545 534 606 556

CFM 1351 1376 1377 1364 1312

Watts 275 357 422 467 515

CFM 1537 1548 1561 1534 1347

Watts 392 468 552 606 538

CFM 1738 1755 1735 1568 1382

Watts 543 652 708 635 563

ON OFF

ON OFF

ON ON

OFF OFF

OFFOFF4**

ONOFFON

OFF

OFFONON

ON

OFFOFFON

OFF

ONOFFOFF

OFF

OFFONOFF

ON

OFFOFF

OFF

PUB. NO. 22-1802-03

10

Performance
Data

*UD2B100AFV32A Furnace Heating Airflow (CFM) and Power (watts) vs. External Static Pressure With Filter

Heating

1st Stage

Heating

Heating

2nd

Stage

Airflow
Setting

Medium** ON

High

Low

Medium**

High

Dip Switch Setting External Static Pressure

SW7 SW8 0.1 0.3 0.5 0.7 0.9

CFM 764 795 832 852 848

ON

ONLow

Temp. Rise 63 61 58 56 57

Watts 103 147 195 242 280

CFM 875 938 963 974 959

OFF

Temp. Rise 55 60 58 57 58

Watts 139 200 259 305 344

CFM 984 1029 1040 1039 980

OFF

OFF

Temp. Rise 49 47 46 46 49

Watts 185 253 304 347 357

CFM 1118 1138 1157 1125 1018

ON ON

Temp. Rise 66 65 64 66 73

Watts 262 326 390 417 383

CFM 1310 1335 1277 1192 1097

ON

OFF

Temp. Rise 57 55 58 62 68

Watts 411 498 498 472 441

CFM 1413 1399 1322 1233 1148

OFF

OFF

Temp. Rise 52 53 56 60 65

Watts 512 566 541 514 484

Unit

Outdoor

1.5

2

2.5

Cooling

3.0**

Notes:

1. * First letter may be "A" or "T".

2. ** Factory setting.

3. Continuous Fan Setting: Heating or cooling airflow is approximately 50% of selected cooling value.

4. For variable speed low speed airflows are approximately 30% of listed values.

5. LOW 350 cfm/ton is recommended for variable speed application for COMFORT & HUMID CLIMATE setting; NORMAL is 400 cfm/ton;
HIGH 450 cfm/ton is for DRY CLIMATE setting.

*UD2B100AFV32A Furnace Cooling Airflow (CFM) and Power (Watts) vs. External Static Pressure With Filter

Airflow

Setting

Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)

SW1 SW2 SW3 SW4 0.1 0.3 0.5 0.7 0.9

ON

ON

ON

OFF

OFF

OFF

ON

ON

ON

OFF OFF OFF

OFF

OFF OFF ON

Dip Switch Setting External Static Pressure

556 574 579 570

80 113 145 176

626 654 647 647

94 131 162 200
706 713 724 730
116 151 187 227
729 745 753 763
124 161 199 238
831 859 872 881
157 207 253 294
939 964 977 954
206 260 309 343
907 934 946 946
188 245 289 334

1044 1055 1065 983

262 319 370 357

1160 1184 1122 1020

344 411 417 386

1089 1105 1108 1003

290 346 399 368

1246 1249 1153 1060

411 469 441 410

1383 1295 1221 1124

546 517 499 467

ON OFF

ON OFF

ON ON

OFF OFF

OFFOFF

ONOFFON

OFF

OFFONON

ON

OFFOFFON

OFF

ONOFFOFF

OFF

OFFONOFF

ON

OFF

OFF

CFM 538

Watts 54

CFM 598

Watts 64

CFM 657

Watts 75

CFM 688

Watts 81

CFM 785

Watts 109

CFM 887

Watts 146

CFM 848

Watts 133

CFM 1018

Watts 206

CFM 1139

Watts 274

CFM 1071

Watts 231

CFM 1208

Watts 323

CFM 1387

Watts 482

11

PUB. NO. 22-1802-03

Performance
Data

*UD2D120AFV52A Furnace Heating Airflow (CFM) and Power (watts) vs. External Static Pressure With Filter

Heating

1st Stage

Heating

Heating

2nd

Stage

Airflow

Setting

Low

Medium** ON

High

Low

Medium**

High

Dip Switch Setting External Static Pressure

SW7 SW8 0.1 0.3 0.5 0.7 0.9

CFM 1003 1039 1062 1033 1034

ON

ON

Temp. Rise 58 56 54 56 56

Watts 125 182 246 309 356

CFM 1137 1193 1185 1197 1185

OFF

Temp. Rise 51 48 49 48 49

Watts 170 239 293 370 446

CFM 1262 1290 1327 1344 1331

OFF

OFF

Temp. Rise 46 45 44 43 43

Watts 218 286 366 440 534

CFM 1415 1454 1476 1500 1421

ON ON

Temp. Rise 63 61 60 59 63

Watts 297 378 453 534 561

CFM 1645 1672 1701 1659 1456

ON

OFF

Temp. Rise 54 53 52 54 61

Watts 435 539 632 671 580

CFM 1834 1857 1837 1686 1506

OFF

OFF

Temp. Rise 48 48 48 53 59

Watts 608 705 778 699 630

*UD2D120AFV52A Furnace Cooling Airflow (CFM) and Power (Watts) vs. External Static Pressure With Filter

Unit

Outdoor

3.5

4

Cooling

5**

Notes:

1. * First letter may be "A" or "T".

2. ** Factory setting.

3. Continuous Fan Setting: Heating or cooling airflow is approximately 50% of selected cooling value.

4. For variable speed low speed airflows are approximately 30% of listed values.

5. LOW 350 cfm/ton is recommended for variable speed application for COMFORT & HUMID CLIMATE setting; NORMAL is 400 cfm/ton;
HIGH 450 cfm/ton is for DRY CLIMATE setting.

Airflow
Setting

Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)
Low (350

CFM/Ton)

Normal (400

CFM/ton)

High (450

CFM/ton)

SW1 SW2 SW3 SW4 0.1 0.3 0.5 0.7 0.9

OFF

OFF

OFF

ON

ON

ON

OFF

OFF

OFF

Dip Switch Setting

ON OFF

ONON

OFF OFF

OFF ON

OFF OFF

ONOFFON

OFF

OFF

ON

OFFOFFOFF

OFF

ONOFFOFF

OFF

OFFONOFF

CFM

Watts

CFM

Watts

CFM

Watts

CFM

Watts

CFM

Watts

CFM

Watts

CFM

Watts

CFM

Watts

CFM

Watts

1141 1197 1205 1196 1188

170 246 299 369 443

1325 1374 1403 1434 1412

252 332 408 496 567

1536 1575 1615 1619 1474

370 464 563 640 605

1334 1376 1424 1411 1417

251 330 415 469 562

1582 1628 1659 1663 1465

387 491 595 672 595

1813 1836 1838 1707 1504

577 684 771 710 620

1704 1731 1733 1735 1552

489 589 666 750 663

1960 1971 1937 1799 1602

739 841 891 813 700
2208 2107 1970 1849 1683
1080 1025 942 863 776

External Static Pressure

PUB. NO. 22-1802-03

12

Electrical
Data

WIRING DIAG WIRING DIAG

WIRING DIAG

WIRING DIAG WIRING DIAG

RAMS FOR GAS FURNACESRAMS FOR GAS FURNACES

RAMS FOR GAS FURNACES

RAMS FOR GAS FURNACESRAMS FOR GAS FURNACES

13

PUB. NO. 22-1802-03

Electrical
Data

SCHEMASCHEMA

SCHEMA

SCHEMASCHEMA

TIC DIAGRAMS FOR GAS FURNACESTIC DIAGRAMS FOR GAS FURNACES

TIC DIAGRAMS FOR GAS FURNACES

TIC DIAGRAMS FOR GAS FURNACESTIC DIAGRAMS FOR GAS FURNACES

PUB. NO. 22-1802-03

14

Field
Wiring

FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 STAGE FURNACE

1 STAGE HEATING

USING A 1 STAGE HEATING THERMOSTAT

NO COOLING

1. Be sure power agrees with equipment nameplates.

2. Low voltage (24 volt wiring) to be No. 18 A.W.G. min.

3. Grounding of equipment must comply with local codes.

4. Set thermostat heat anticipator per unit wiring diagram.

5. These leads provide 115V. power for connection of humidifier
MAX. load 1.0 amp.

6. When a single stage heating thermostat without fan switch
is used, no wiring on "G" terminal is used.

7. W1 and W2 must be jumpered together for proper operation.
Second stage heat will begin 10 minutes after first stage.

8. Set dip switches with power off per installation instructions
to set airflow and indoor fan off delays.

9. Continuous fan airflow can be increased by adding this jumper.

10. This wire is only for thermostats requiring connection to
transformer common terminal.

11. Optional humidistat is to be connected between R and BK. Factory installed jumper R
to BK on the circuit board must be cut if optional humidistat is used. The jumper must

SEE

NOTE 9

W1 TO W2.

2ND STAGE WILL FIRE

also be cut when applying an airflow command signal to the BK input such as with the
variable speed single-zone and multi-zone system controllers. On single speed cooling
only/non-heat pump systems, jumper Y to O for proper operation of the delay profiles
and the humidistat. For two compressor or two speed systems, jumper YLo to O.

SEE

NOTE 6

Y1/Ylo

W14

W14 JUMPER
SEE NOTE 11

FIELD ADDED JUMPER

10 MINUTES AFTER 1ST.

SEE

B/C

NOTE 10

B/C

TO 115 V 1 PH.,
60 HZ., POWER
SUPPLY PER
LOCAL CODES

HUM SEE
NOTE 5

15

From Dwg. B342027 Rev. 0

PUB. NO. 22-1802-03

Field
Wiring

FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 STAGE FURNACE

2 STAGE HEATING

USING A 2 STAGE HEATING THERMOSTAT

NO COOLING

1. Be sure power agrees with equipment nameplates.

2. Low voltage (24 volt wiring) to be No. 18 A.W.G. min.

3. Grounding of equipment must comply with local codes.

4. Set thermostat heat anticipator per unit wiring diagram.

5. These leads provide 115V. power for connection of humidifier
MAX. load 1.0 amp.

6. This wire is only for thermostats requiring connection to
transformer common terminal.

7. Continuous fan airflow can be increased by adding this jumper.

8. Set dip switches with power off per installation instructions
to set airflow and indoor fan off delays.

9. Optional humidistat is to be connected between R and BK. Factory
installed jumper R to BK on the circuit board must be cut if optional
humidistat is used. The jumper must also be cut when applying an airflow
command signal to the BK input such as with the variable speed single-zone
and multi-zone system controllers. On single speed cooling only/non-heat pump
systems, jumper Y to O for proper operation of the delay profiles and the humidistat.
For two compressor or two speed systems, jumper YLo to O.

Y1/Ylo

W14

W14 JUMPER

SEE NOTE 9

SEE

NOTE 7

SEE

B/C

PUB. NO. 22-1802-03

NOTE 6

B/C

TO 115 V 1 PH.,
60 HZ., POWER
SUPPLY PER
LOCAL CODES

HUM SEE
NOTE 5

From Dwg. B342025 Rev. 0

16

OUTDOOR UNIT

(NO TRANSFORMER)

Field
Wiring

FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 STAGE FURNACE

1 STAGE HEATING, 1 STAGE COOLING

USING A 1 STAGE HEATING, 1 STAGE COOLING THERMOSTAT

(OUTDOOR SECTION WITHOUT TRANSFORMER)

W14

W14 JUMPER

SEE NOTE 9

Y1/Ylo

SEE

NOTE 7

B/C

SEE

NOTE 6

B/C

FIELD ADDED JUMPER

W1 TO W2.

2ND STAGE WILL FIRE

10 MINUTES AFTER 1ST.

TO 115 V 1 PH.,
60 HZ., POWER
SUPPLY PER
LOCAL CODES

HUM SEE
NOTE 5

From drawing B342022 Rv 0

17

PUB. NO. 22-1802-03

OUTDOOR UNIT

(NO TRANSFORMER)

Field
Wiring

FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 STAGE FURNACE

2 STAGE HEATING, 1 STAGE COOLING

USING A 2 STAGE HEATING, 1 STAGE COOLING THERMOSTAT

(OUTDOOR SECTION WITHOUT TRANSFORMER)

W14

SEE

NOTE 9

SEE

NOTE 7

Y1/Ylo

W14 JUMPER

SEE NOTE 9

SEE

B/C

PUB. NO. 22-1802-03

NOTE 6

B/C

TO 115 V 1 PH.,
60 HZ., POWER
SUPPLY PER
LOCAL CODES

HUM SEE
NOTE 5

18

From Dwg. B342020 Rev. 0

OUTDOOR UNIT NO. 1

(NO TRANSFORMER)

SEE NOTE 3

Field
Wiring

FIELD WIRING DIAGRAM FOR VARIABLE SPEED 2 STAGE FURNACE

2 STAGE HEATING, 2 STAGE COOLING

(OUTDOOR SECTION WITHOUT TRANSFORMER)

W14

OUTDOOR UNIT NO. 2

(NO TRANSFORMER)

B/C

SEE

NOTE 7

SEE

NOTE 6

B/C

TO 115 V 1 PH.,
60 HZ., POWER
SUPPLY PER
LOCAL CODES

HUM SEE
NOTE 5

From Dwg. B342018 Rev. 0

19

PUB. NO. 22-1802-03

Dimensions

(ALL DIMENSIONS ARE IN INCHES)

*UD2 OUTLINE DRAWING

17-1/2" 9-5/8" 16-1/4" 16" 16"

MODEL DIM "A" DIM "B" DIM "C" DIM "D" DIM "E"

*UD2B060AFV32A

*UD2B080AFV32A

*UD2B100AFV32A

*UD2C080AFV42A 21" 13-1/16" 19-3/4" 19-1/2" 19-1/2"

*UD2D120AFV52A 24-1/2" 15-5/16" 23-1/4" 23" 23"

* PREFIX LETTER MAY BE "A" OR "T"

Bottom Return ONLY

NOTES

Trane

6200 Troup Highway
Tyler, TX 75707
www.trane.com

Since Trane has a policy of continuous product improvement, it reserves the right to change design and
specifications without notice.