Trane TUD040, TUD0060, TUD0080, TUD0100, TUD0120 User Manual

...
Page 1
Upflow/Horizontal Right or Upflow/Horizontal Left Induced Draft Gas Furnace
XR 80
TUD040,060,080,100,120,140C
Single-Stage Fan Assisted Combustion System
PUB. NO. 22-1640-06-0702 (EN)
Page 2
General Features
Natural Gas Models
Central Heating furnace designs are certified by the American and Canadian Gas Associations for both natural and L.P. gas. Limit setting and rating data were established and approved under standard rating conditions using American National Standards Institute standards.
Safe Operation
The Integrated System Control has solid state devices, which continuously monitor for presence of flame, when the system is in the heating mode of operation. Dual solenoid combination gas valve and regulator provide extra safety.
Quick Heating
Durable, cycle tested, heavy gauge
aluminized steel heat exchanger
quickly transfers heat to provide warm conditioned air to the structure.
Burners
Multi-port In-shot burners will give years of quiet and efficient service. All models can be converted to L.P. gas.
Integrated System Control
Exclusively designed operational pro­gram provides total control of furnace limit sensors, blowers, gas valve, flame control and includes self diagnostics for ease of service. Also contains connec­tion points for E.A.C./humidifier.
Air Delivery
The 4-speed, direct drive blower motor, has sufficient airflow for most heating and cooling requirements, will switch from heating to cooling speeds on demand from room thermostat. The blower door safety switch will prevent or terminate furnace operation when the blower door is removed.
Styling Heavy gauge steel and “wrap-around” cabinet construction is used in the
cabinet with baked-on enamel finish for strength and beauty. The heat exchanger section of the cabinet is completely lined with foil faced fiberglass insulation. This results in quiet and efficient operation due to the excellent acoustical and insulating qualities of fiberglass.
Features And General Operation
The XR 80 High Efficiency Gas Furnaces employ an adaptive Hot Surface Ignition system, which eliminates the waste of a constant burning pilot. The integrated system control lights the main burners upon a demand for heat from the room thermostat. Complete front service access.
a. Low energy power venter. b. Vent proving pressure switch.
© 2002 American Standard Inc. All Rights Reserved 2 22-1640-06-0702 (EN)
Page 3
Contents
General Features 2 Features and Benefits 4
Standard Equipment 4 Optional Equipment 5
General Data 6
TUD040C924K 6 TUD040C930K 6 TUD060C924K 6 TUD060C936K 6 TUD080C924K 7 TUD080C936K 7 TUD080C948K 7 TUD080C960K 7 TUD100C936K 8 TUD100C945K 8 TUD100C948K 8 TUD100C960K 8 TUD100C972K 9 TUD120C954K 9 TUD120C960K 9 TUD140C960K 9
Performance Data 10 Field Wiring 12 Twinning Field Wiring 13 Dimensions 14 Electrical Data 15
22-1640-06-0702 (EN) 3
Page 4
Features and Benefits
XR 80 Upflow/Horizontal Right Or Left
Standard Equipment
• Power supply 115/1/60
• Multi-port In-shot burners
• Integrated solid state control with self diagnostics
• Silicon Nitride hot surface igniter with adaptive heat up
• Complete front service access
• Heavy guage aluminized steel heat exchanger
• Slide out blower assembly
• Blower door safety switch
• Direct drive, 4-speed motor
• Cleanable high velocity filters
• Optional L.P. conversion kit
• Common vent
• Alternate bottom/left/right return air
• Hinged blower door
• Perfect Fit door latches
• Gasketed blower door
• Internal filter rack
• Cleanable high velocity filters
• Standard filter sizes
• Single wire twinning
• Selectable cooling fan off delay
• Left-right gas connection
• Optional L.P. conversion kit
• Common vent capability
• 24 volt fuse
• Manual reset flame roll out switches
• Insulated blower door
• Insulated blower compartment
• Accessory hook-up capability - Hum and EAC
• Blower door safety switch
• Left/right gas connection
• 24 volt fuse
• Manual reset burner box limit
Non-prorated 20-year heat ex-
changer limited warranty
5-year limited parts warranty
4 22-1640-06-0702 (EN)
Page 5
Features and Benefits
Optional Equipment
Thermostat .............................................................................................................................................................. BAYSTAT388 [ ]
Thermostat, Heating/Cooling Single Stage (Mounts Horizontally) ................................................................................ AY28X092 [ ]
Thermostat, Heating/Cooling Single Stage (Mounts Vertically) ................................................................................ BAYSTAT305 [ ]
Thermostat, Electronic Programmable 1-Stage Heating/1-Stage Cooling .............................................................. TAYSTAT300C [ ]
Propane Conversion Kit ........................................................................................................................................ BAYLPKT210A [ ]
Electronic Air Filter, “Perfect Fit” Super Efficiency (14-1/2" Wide Gas Furnace) ..................................................... TFE145A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” Super Efficiency (17-1/2" Wide Gas Furnace) ..................................................... TFE175A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” Super Efficiency (21" Wide Gas Furnace) ........................................................... TFE210A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” Super Efficiency (24-1/2" Wide Gas Furnace) ..................................................... TFE245A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” High Efficiency (14-1/2" Wide Gas Furnace) .......................................................TFM145A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” High Efficiency (17-1/2" Wide Gas Furnace) .......................................................TFM175A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” High Efficiency (21" Wide Gas Furnace) ............................................................. TFM210A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” High Efficiency (24-1/2" Wide Gas Furnace) .......................................................TFM245A9FR1 [ ]
Electronic Air Filter, “Perfect Fit” Standard Efficiency (17-1/2" Wide Gas Furnace) .............................................. TFP175A9FR01 [ ]
Electronic Air Filter, “Perfect Fit” Standard Efficiency (21" Wide Gas Furnace) .................................................... TFP210A9FR01 [ ]
Electronic Air Filter, “Perfect Fit” Standard Efficiency (24-1/2" Wide Gas Furnace) .............................................. TFP245A9FR01 [ ]
Coil Enclosure (14-1/2" Wide Cabinets) ................................................................................................................ BAYCLE1400C [ ]
Coil Enclosure (17-1/2" Wide Cabinets) ................................................................................................................ BAYCLE1700C [ ]
Coil Enclosure (21" Wide Cabinets) ...................................................................................................................... BAYCLE2100C [ ]
Coil Enclosure (24-1/2" Wide Cabinets) ................................................................................................................ BAYCLE2400C [ ]
High Altitude Pressure Switch Kit .............................................................................................................................BAYHALT248 [ ]
Masonry Chimney Vent Kit ................................................................................................................................... BAYVENT800B [ ]
Filter Rack Kit ...................................................................................................................................................... BAYRACK960A [ ]
22-1640-06-0702 (EN) 5
Page 6
General Data
Product Specifications 1
MODEL TYPE RATINGS
Input BTUH Capacity BTUH (ICS) AFUE Temp. rise (Min.-Max.) °F.
BLOWER DRIVE
Diameter - Width (In.) No. Used Speeds (No.) CFM vs. in. w.g. Motor HP R.P.M. Volts / Ph / Hz
COMBUSTION FAN - Type
Drive - No. Speeds Motor HP - RPM Volts / Ph / Hz FLA
FILTER — Furnished?
Type Recommended Hi Vel. (No.-Size-Thk.)
VENT — Size (in.) HEAT EXCHANGER
Type -Fired
Gauge (Fired)
ORIFICES — Main
Nat. Gas. Qty. — Drill Size L.P. Gas Qty. — Drill Size
GAS VALVE PILOT SAFETY DEVICE
Ty p e
BURNERS — Type
Number
POWER CONN. — V / Ph / Hz
Ampacity (In Amps) Max. Overcurrent Protection (Amps)
PIPE CONN. SIZE (IN.) DIMENSIONS
Crated (In.)
WEIGHT
Shipping (Lbs.) / Net (Lbs)
1 2
3 4
2
3
-Unfired
4
Central Furnace heating designs are certified by AGA and CSA. For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applications,
above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above sea level. Based on U.S. government standard tests. The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.
TUD040C924K
Upflow / Horizontal
40,000 32,000
80.0
30 - 60
DIRECT
10 x 6
1 4
See Fan Performance Table
1/5
1080
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
2 — 45 2 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
2
115/1/60
6.3 15
1/2
H x W x D
41-3/4 x 16-1/2 x 30-1/2
119 / 110
TUD040C930K
Upflow / Horizontal
40,000 32,000
80.0
30 - 60
DIRECT
10 x 6
1 4
See Fan Performance Table
1/3
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0 Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
2 — 45 2 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
2
115/1/60
6.3 15
1/2
H x W x D
41-3/4 x 16-1/2 x 30-1/2
122 / 113
TUD060C924K
Upflow / Horizontal
60,000 47,000
80.0
35 - 65
DIRECT
10 x 6
1 4
See Fan Performance Table
1/5
1080
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0 Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
3 — 45 3 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
3
115/1/60
10.4 15
1/2
H x W x D
41-3/4 x 16-1/2 x 30-1/2
124 / 115
TUD060C936K
Upflow / Horizontal
60,000 47,000
80.0
30 - 60
DIRECT
10 x 7
1 4
See Fan Performance Table
1/3
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0 Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
3 — 45 3 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
3
115/1/60
10.4 15
1/2
H x W x D
41-3/4 x 16-1/2 x 30-1/2
127 / 118
6 22-1640-06-0702 (EN)
Page 7
General Data
Product Specifications 1
MODEL TYPE RATINGS
Input BTUH Capacity BTUH (ICS) AFUE Temp. rise (Min.-Max.) °F.
BLOWER DRIVE
Diameter - Width (In.) No. Used Speeds (No.) CFM vs. in. w.g. Motor HP R.P.M. Volts / Ph / Hz
COMBUSTION FAN - Type
Drive - No. Speeds Motor HP - RPM Volts / Ph / Hz FLA
FILTER — Furnished?
Type Recommended Hi Vel. (No.-Size-Thk.)
VENT — Size (in.) HEAT EXCHANGER
Type -Fired
Gauge (Fired)
ORIFICES — Main
Nat. Gas. Qty. — Drill Size L.P. Gas Qty. — Drill Size
GAS VALVE PILOT SAFETY DEVICE
Ty p e
BURNERS — Type
Number
POWER CONN. — V / Ph / Hz
Ampacity (In Amps) Max. Overcurrent Protection (Amps)
PIPE CONN. SIZE (IN.) DIMENSIONS
Crated (In.)
WEIGHT
Shipping (Lbs.) / Net (Lbs)
1 2
3 4
2
3
-Unfired
4
Central Furnace heating designs are certified by AGA and CSA. For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applications,
above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above sea level. Based on U.S. government standard tests. The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.
TUD080C924K
Upflow / Horizontal
80,000 64,000
80.0
50 - 80
DIRECT
9 x 7
1 4
See Fan Performance Table
1/5
1080
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0 Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
4 — 45 4 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
4
115/1/60
10.4 15
1/2
H x W x D
41-3/4 x 19-1/2 x 30-1/2
139 / 129
TUD080C936K
Upflow / Horizontal
80,000 63,000
80.0
30 - 60
DIRECT
10 x 7
1 4
See Fan Performance Table
1/3
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
4 — 45 4 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
4
115/1/60
10.4 15
1/2
H x W x D
41-3/4 x 19-1/2 x 30-1/2
142 / 132
TUD080C948K
Upflow / Horizontal
80,000 64,000
80.0
30 - 60
DIRECT
10 x 8
1 4
See Fan Performance Table
1/3
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
4 — 45 4 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
4
115/1/60
9.1 15
1/2
H x W x D
41-3/4 x 19-1/2 x 30-1/2
142 / 132
TUD080C960K
Upflow / Horizontal
80,000 64,000
80.0
25 - 55
DIRECT
11 x 10
1 4
See Fan Performance Table
3/4
1100
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 20x25 - 1in.
4 Round
Aluminized Steel - Type I
20
4 — 45 4 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
4
115/1/60
13.8 15
1/2
H x W x D
41-3/4 x 23 x 30-1/2
162 / 151
22-1640-06-0702 (EN) 7
Page 8
General Data
Product Specifications 1
MODEL TYPE RATINGS
Input BTUH Capacity BTUH (ICS) AFUE Temp. rise (Min.-Max.) °F.
BLOWER DRIVE
Diameter - Width (In.) No. Used Speeds (No.) CFM vs. in. w.g. Motor HP R.P.M. Volts / Ph / Hz
COMBUSTION FAN - Type
Drive - No. Speeds Motor HP - RPM Volts / Ph / Hz FLA
FILTER — Furnished?
Type Recommended Hi Vel. (No.-Size-Thk.)
VENT — Size (in.) HEAT EXCHANGER
Type -Fired
Gauge (Fired)
ORIFICES — Main
Nat. Gas. Qty. — Drill Size L.P. Gas Qty. — Drill Size
GAS VALVE PILOT SAFETY DEVICE
Ty p e
BURNERS — Type
Number
POWER CONN. — V / Ph / Hz
Ampacity (In Amps) Max. Overcurrent Protection (Amps)
PIPE CONN. SIZE (IN.) DIMENSIONS
Crated (In.)
WEIGHT
Shipping (Lbs.) / Net (Lbs)
1 2
3 4
2
3
-Unfired
4
Central Furnace heating designs are certified by AGA and CSA. For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applications,
above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above sea level. Based on U.S. government standard tests. The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.
TUD100C936K
Upflow / Horizontal
100,000
79,000
80.0
40 - 70
DIRECT
10 x 7
1 4
See Fan Performance Table
1/3
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
5 — 45 5 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
5
115/1/60
10.4 15
1/2
H x W x D
41-3/4 x 19-1/2 x 30-1/2
151 / 141
TUD100C945K
Upflow / Horizontal
100,000
79,000
80.0
35 - 65
DIRECT
10 x 8
1 4
See Fan Performance Table
1/3
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 17x25 - 1in.
4 Round
Aluminized Steel - Type I
20
5 — 45 5 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
5
115/1/60
10.4 15
1/2
H x W x D
41-3/4 x 19-1/2 x 30-1/2
153 / 143
TUD100C948K
Upflow / Horizontal
100,000
79,000
80.0
35 - 65
DIRECT
10 x 8
1 4
See Fan Performance Table
1/2
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0 Ye s
High Velocity
1 - 20x25 - 1in.
4 Round
Aluminized Steel - Type I
20
5 — 45 5 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
5
115/1/60
12.0 15
1/2
H x W x D
41-3/4 x 23 x 30-1/2
162 / 151
TUD100C960K
Upflow / Horizontal
100,000
79,000
80.0
30 - 60
DIRECT
11 x 10
1 4
See Fan Performance Table
1/2
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0 Ye s
High Velocity
1 - 20x25 - 1in.
4 Round
Aluminized Steel - Type I
20
5 — 45 5 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
5
115/1/60
12.8 15
1/2
H x W x D
41-3/4 x 23 x 30-1/2
162 / 151
8 22-1640-06-0702 (EN)
Page 9
General Data
Product Specifications 1
MODEL TYPE RATINGS
Input BTUH Capacity BTUH (ICS) AFUE Temp. rise (Min.-Max.) °F.
BLOWER DRIVE
Diameter - Width (In.) No. Used Speeds (No.) CFM vs. in. w.g. Motor HP R.P.M. Volts / Ph / Hz
COMBUSTION FAN - Type
Drive - No. Speeds Motor HP - RPM Volts / Ph / Hz FLA
FILTER — Furnished?
Type Recommended Hi Vel. (No.-Size-Thk.)
VENT — Size (in.) HEAT EXCHANGER
Type -Fired
Gauge (Fired)
ORIFICES — Main
Nat. Gas. Qty. — Drill Size L.P. Gas Qty. — Drill Size
GAS VALVE PILOT SAFETY DEVICE
Ty p e
BURNERS — Type
Number
POWER CONN. — V / Ph / Hz
Ampacity (In Amps) Max. Overcurrent Protection (Amps)
PIPE CONN. SIZE (IN.) DIMENSIONS
Crated (In.)
WEIGHT
Shipping (Lbs.) / Net (Lbs)
1 2
3 4
2
3
-Unfired
4
Central Furnace heating designs are certified by AGA and CSA. For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000 feet above sea level. For Canadian applications,
above input ratings (BTUH) are up to 4,500 feet, derate 4% per 1,000 feet for elevations above 4,500 feet above sea level. Based on U.S. government standard tests. The above wiring specifications are in accordance with National Electrical Code; however, installations must comply with local codes.
TUD100C972K
Upflow / Horizontal
100,000
80000
80.0
30 - 60
DIRECT
11 x 10
1 4
See Fan Performance Table
3/4
1100
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 24x25 - 1in.
4 Round
Aluminized Steel - Type I
20
5 — 45 5 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
5
115/1/60
13.1 15
1/2
H x W x D
41-3/4 x 26-1/2 x 30-1/2
175 / 163
TUD120C954K
Upflow / Horizontal
120,000
96,000
80.0
35 - 65
DIRECT
11 x 10
1 4
See Fan Performance Table
1/2
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0 Ye s
High Velocity
1 - 20x25 - 1in.
4 Round
Aluminized Steel - Type I
20
6 — 45 6 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
6
115/1/60
12.8 15
1/2
H x W x D
41-3/4 x 23 x 30-1/2
176 / 164
TUD120C960K
Upflow / Horizontal
120,000
96,000
80.0
30 - 60
DIRECT
11 x 10
1 4
See Fan Performance Table
1/2
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 24x25 - 1in.
4 Round
Aluminized Steel - Type I
20
6 — 45 6 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
6
115/1/60
12.8 15
1/2
H x W x D
41-3/4 x 26-1/2 x 30-1/2
186 / 174
TUD140C960K
Upflow / Horizontal
140,000 111,000
80.0
40 - 70
DIRECT
11 x 10
1 4
See Fan Performance Table
3/4
1075
115/1/60
Centrifugal
Direct - 1
1/50 - 3000
115/1/60
1.0
Ye s
High Velocity
1 - 24x25 - 1in.
4 Round
Aluminized Steel - Type I
20
7 — 45 7 — 56
Redundant - Single Stage
Hot Surface Ignition
Multi-port In-shot
7
115/1/60
13.1 15
1/2
H x W x D
41-3/4 x 26-1/2 x 30-1/2
193 / 181
22-1640-06-0702 (EN) 9
Page 10
Performance Data
FURNACE AIRFLOW (CFM) VS. STATIC PRESSURE (ins. w.g.)
MODEL SPEED TAP 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90
4 -
TUD040C924K
TUD040C930K
TUD060C924K
TUD060C936K
TUD080C924K
TUD080C936K
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
HIGH - Black
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
HIGH - Black
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
HIGH - Black
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
1018
847 716 617
1307 1172 1030
892
1013
835 712 611
1426 1243 1042
900
1115
919 772 643
1393 1210 1046
900
1004
832 701
599
1262 1140 1007
876
997 821 702 596
1389 1225 1039
903
1094
912 767 655
1384 1209 1052
903
982 809 678 575
1211 1100
976 856
973 800 683 573
1345 1197 1027
895
1060
891 750 648
1364 1198 1047
895
950 779 648 544
1164 1053
938 893
941 771 655 543
1298 1160 1005
877
1014
857 722 622
1335 1177 1033
888
910 742 610 507
1092
996 893 789
901 734 617 505
1236 1113
973 848
956 809
681 577
1296 1147 1008
869
860 697 585 463
1023
937 840 744
852 689 571 459
1171 1057
931 809
886 747 629 512
1247 1107
963 842
802 644 512 413
949 867 779 691
796 636 516 406
1099
991 879 760
803 671 565 428
1189 4058
928 808
763 585 452 357
869 791 712 630
731 575 452 345
1020
916 817 700
708 582 489 325
1120
999 873 766
660 517 384 294
783 707 636
561
659 506 379 277
934
831 745 629
600 478
401 203
1042
930 808 717
TUD080C948K
TUD080C960K
TUD100C936K
TUD100C945K
TUD100C948K
TUD100C960K
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
4 -
HIGH - Black
3 -
MED.-HIGH - Blue
2 -
MED.-LOW - Yellow
1 -
LOW - Red
1839 1323 1092
788
2308 2006 1690 1437
1476 1249 1020
873
1771 1375 1127
780
1880 1662 1428 1208
2181 1908 1621 1443
1821 1325 1090
783
2281 1997
1691 1437
1464 1257 1046
887
1731
1371
1141
815
1846 1635
1421 1215
2143 1888 1609 1419
1796 1329 1091
2254 1987
1691
1437
1441 1252 1058
1355 1328 1124
1799 1598 1402 1210
2104 1868 1597 1395
10 22-1640-06-0702 (EN)
780
890
829
1756 1319 1083
768
2209 1960 1683 1434
1408 1234 1050
883
1624 1328 1124
822
1740 1551 1370 1193
2053 1834 1582 1381
1710 1308 1076
758
2163 1933 1674 1431
1363 1203 1028
864
1556 1289 1094
796
1669 1493 1326 1164
2001 1800 1567 1367
1641 1275 1059
737
2095 1888 1651 1418
1307 1158
990 834
1479 1238 1049
749
1595 1424 1269 1124
1929 1745 1533 1335
1573 1246 1040
719
2026 1842 1627 1404
1241 1101
936 794
1392 1176
989 681
1489 1345 1199 1073
1856 1690 1498 1302
1480 1201 1005
647
1950 1780 1556 1369
1163 1030
866 742
1296 1102
914 593
1381 1256 1117 1009
1766 1631 1438 1256
1392 1165
970 630
1873 1718 1485 1334
1074
946 780 680
1191 1016
825 485
1260 1157 1022
935
1676 1572 1377 1209
Page 11
Performance Data
FURNACE AIRFLOW (CFM) VS. STATIC PRESSURE (ins. w.g.)
MODEL SPEED TAP 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90
HIGH - Black
TUD100C972K
BOTTOM AND
LEFT SIDE
RETURN
TUD100C972K
TUD120C954K
TUD120C960K
TUD140C960K
Note 1: High speed CFM is based on bottom and left side return option for this model. Medium High, Medium Low, and Low speed taps for this model do not have
improved airflow with the addition of side return.
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
HIGH - Black
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
HIGH - Black
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
HIGH - Black
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
HIGH - Black
4 -
MED.-HIGH - Blue
3 -
MED.-LOW - Yellow
2 -
LOW - Red
1 -
2484 2458 2432 2387 2342
NOTE
2303
2356
1459
1889
1906 1646
1755
2401
2088
1750 1456
2130
1881 1643 1421
2101
18814
1632 1415
2407
2112 1746 1446
2079 1748 1453
2097 1873
1631
1414 2066
1856 1617 1407
2351 2096 1736 1442
2053 1732 1443
2067 1839 1619 1400
2036 1817 1596
1391
2284 2054 1719 1427
2447 2097 1753
2162
1654 1427
2135
1423 2462
2128
1450
2275 2208 2125 2041
SEE
1
2249 2028 1716 1434
2037 1805 1606 1386
2005 1777 1575 1375
2216
2011
1702
1411
2173
2143
1970 1690 1407
1976 1776 1572 1357
1923 1724 1535 1338
1949 1656 1383
2097 1912 1665 1380
1914 1746 1538 1327
1840
1671 1494 1300
2069 1887 1609 1354
1994 1831 1594 1335
1833 1670 1483 1285
1750 1602 1427 1246
1989 1797 1564 1298
1892 1750 1523 1289
1752 1593 1428 1243
1659 1533 1360 1192
1908 1706 1518 1241
CFM VS. TEMPERATURE RISE
MODEL
TUD040C924K 59 49 42 37 33 30
TUD040C930K
TUD060C924K
TUD060C936K 56 49 44 40 37 34 32
TUD080C924K
TUD080C936K
TUD080C948K 59 54 49 46 42 40 37 35 33
TUD080C960K
TUD100C936K
TUD100C945K 62 57 53 49 46 44 41
TUD100C948K
TUD100C960K
TUD100C972K 62 57 53 49 46 44 41 39 37 35 34 32 31
TUD120C954K
TUD120C960K
TUD140C960K 69 65 61 58 55 52 49 47 45
500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000 2100 2200 2300 2400
59 49 42 37 33
63 56 49 44
74 66 59 54
59 54 49 46 42
Cubic Feet Per Minute (CFM)
54 49 46 42 40 37 35 33 31 30 28 27 26
67 62 57 53 49
67 62 57 53 49 46 44 41 39 37
62 57 53 49 46 44 41 39 37 35 34 32 31
63 59 56 52 49 47 44 42 40
59 56 52 49 47 44 42 40
22-1640-06-0702 (EN) 11
Page 12
Field Wiring
Field Wiring Diagram For Heating Only
Field Wiring Diagram For Single Stage Heating/Cooling
(Outdoor Section Without Transformer)
From Dwg. 21B341437 Rev. 1
From Dwg. 21B341436 Rev. 1
12 22-1640-06-0702 (EN)
Page 13
Twinning Field Wiring
From Dwg. 21B341422 Rev. 1
22-1640-06-0702 (EN) 13
From Dwg. 21B341423Rev. 1
Page 14
14 22-1640-06-0702 (EN)
From Dwg. 21C341699 Rev. 1
TUD-C Outline Drawing
(All dimensions are in inches)
Page 15
Electrical Data
Schematic Diagrams for Gas Furnaces
22-1640-06-0702 (EN) 15
From Dwg. 21D341704 Rev. 1
Page 16
Trane A business of American Standard Companies www.trane.com
Literature Order Number FURN-PRC001-EN File Number — Supersedes TUD-D-1 3/98 Stocking Location PI Louisville & Webb/Mason-Houston 7/02
Trane has a policy of continuous product and product data improvement and it reserves the right to change design and specifications without notice.
P.I.
Loading...