Page 1
Name and function of wireless remote control
ON/OFF button
Remote control
Signal transmitter
AUTO
COOL
DRY
FAN
( )
●
Press this button to set up the clock time.
The and time display will begin to blink.
Adjust the time by pressing the
or
buttons. Press
and hold the
button to change the time
value quickly. Press this button once
again to fix the time setting and exit the
clock set up.
Note: If a button is not pressed within 5
seconds (while the display is blinking) the
clock set up will exit and the setting will
not be saved.
CLOCK button
CLOCK
●
Press this button to toggle between a display
of the indoor set point, indoor room
temperature and outdoor temperature (outdoor
temperature is only available on select models).
TEMP button
TEMP
Do not drop or throw the remote control; Do not let any liquid in the remote control.
Note: Be sure that there are no obstructions between receiver and remote controller;
Do not put the remote control directly in sunlight or any place where it is very hot.
●
Each time you press this button, a mode is
selected in a sequence that goes from AUTO,
COOL, DRY, FAN and HEAT*.
MODE button
MODE
After the unit is turned on, the default operating
mode will be AUTO. In the AUTO mode, the indoor
set point will not be displayed as the unit will
automatically select the suitable operating mode
and temperature set point to make the room
temperature comfortable.
●
This button is used for setting Fan Speed in
the sequence that goes from AUTO, Low,
Medium-Low, Medium, Medium-High, High
then back to AUTO.
NOTE: Not all fan speeds are available on all units.
FAN button
FAN
Operation of wireless remote control
●
Press to start or stop operation. Press
this button to turn on the unit. Press this
button again to turn off the unit. Turning
the unit off will cancel any sleep, quiet,
or timer functions.
HEAT
Once the unit is turned on, the indoor
set point is the default temperature
displayed.
Mediumfan
Low fan
High fan
●
Press this button to turn the indoor unit
display on or off. When the unit is turned
on, the default is to have the unit display on.
LIGHT button
LIGHT
Medium-low fan
Medium-high fan
Note: Dry mode uses the low fan speed.
-1-
*only for models with heating function
AUTO
TEMP button
or
CLOCK button
MS-SVU052A-EN 04/14
timer on or timer off.
Guide for operation- general operation
Operation of wireless remote control
★
This function allows removal of moisture on the evaporator of the indoor unit after
the unit has stopped. X-FAN is not available in AUTO, FAN or HEAT mode.
About X-FAN function
1. Having set X-FAN function on: After turning off the unit by pressing ON/OFF button
indoor fan will continue running for about 10 min at low speed. During this time
press X-FAN button again to stop the indoor fan sooner.
2. Having set X-FAN function off: After turning off the unit by pressing ON/OFF button,
the complete unit will be turned off immediately.
Introduction for special function
When AUTO RUN mode is selected, the set point temperature will not be displayed on the
LCD. The unit will be compared with the room tem
perature to automatically select the suitable
running method to achieve the desired set point.
About TURBO function
★
★
About AUTO RUN
1. Press SLEEP button, to set sleep.
2. Press TIMER ON and TIMER OFF button, can set the scheduled
3. Press LIGHT button, to control the light on and off of the unit display.
(This function may be not available for some units).
4. Press TURBO button, to select the ON and OFF of TURBO function.
close automatically.)
5. Press or buttons to select the swing.
4. Press FAN button, to set the fan speed, can select AUTO FAN, LOW,
MEDIUM-LOW, MEDIUM, MEDIUM-HIGH and HIGH. (NOTE: Not all fan speeds are available
for all units)
3. Press
or
button, to set the desired temperature (It is
unnecessary to set the temp.
at AUTO mode.)
2. Press MODE button, select desired running mode.
will start to run. (Note: When it is powered OFF, the guide louver of main unit will
1. After the unit is installed and electricity is connected, press ON/OFF button, the unit
Guide for operation- Optional operation
-6-
When selecting this function the unit will run at the highest fan speed to cool or heat quickly
so that the room temperature reaches the desired set point as soon as possible.
MS-SVU052A-EN 04/14
Press and buttons simultaneously to lock or unlock the keypad. If the
remote controller
flicker three times. If the keypad is unlocked, the mark will disappear.
1.
Press swing up and down button continuou
sly more than two seconds,and the main unit
will swing back
and forth from up to down. Release the button, and the unit will stop swinging and current
position of guide louver will be kept.
2. Under swing up and down mode, when the status is switched from off to , press this
button again two seconds later, status will switch to off, press this button again
within two seconds. The changeof swin
g statuswilla
lsodepend onthe circulation sequence statedabove.
★
★
★
★
About swing up and down
1.
Press swing left and right button continuously more than two seconds, the main unit will swing back
and forth from left to right. Release the button, and the unit will stop swinging and current
position of guide louver will be kept.
2. Under swing left and right mode, when the status is switched from off to , press this
button again two seconds later, status will switch to off, press this button again
within two seconds, the changeof swingstatuswill alsodepend onthe circulation sequence statedabove.
★
About swing left and right
About lock
Operation of wireless remote control
About switch between Fahrenheit and Centigrade
When unit is powered off
, press MODE and use buttons simultaneously to switch
℃ and ℉.
★
About Quiet function
If Auto Quiet mode has been selected, after the room
temperature has reached the set point
temperatureor 10 minutes later, the ACwill immediately enter intothe Quiet running mode, at
★
this time the fan speedis not adjustable.
About Sleep function
Under the Fan and Auto mode, the Sleep function cannot be set up, under DRY
mode, only Sleep 1 can be selected. Select and enter into any kind of Sleep mode, the
★
Quiet functionwill be started. Other Quietstatuscould be optionalandturned off.
Press “TEMP” and “CLOCK” simultaneously in COOL mode to start energy-saving function.
The display screen on the remote controller displays “SE”. Repeat the operation to quit the function.
Press “TEMP” and “CLOCK” simultaneously in HEAT mode to start 8℃ Heating
.
on the remote controller
displays
“ ”
and a selected temperature of
“ 8
℃
(46°F)
”
(46 if Fahrenheiti sadopted). Repeat the operation to quit the function.
Combination of " TEMP" and "CLOCK" buttons : About 8
Combination of " TEMP" and "CLOCK" buttons : About Energy-saving Function
℃(46°F) Heating Function
℉
(46°F)
-7-
Function.
The display screen
is locked, the icon will be displayed. Press any key and the lock icon will
MS-SVU052A-EN 04/14
●
●
●
●
●
●
●
Operation of remote control
Changing batteries and notices
1.Lightly press the place with , along the arrowhead
direction to push the back cover of wireless remote control.
(As shown in Fig 1. )
2.Take out the old batteries.
3.Insert two new AAA1.5V dry batteries, and pay attention
Fig.1
Fig.2
NOTE:
When changing the batteries, do not use old or
different batteries, otherwise, it can cause malfunction of the wireless remote control.
If the wireless remote control will not be used for
a long period, take the batteries out to avoid battery
leakage and damage to the wireless remote control.
It should be placed 1m(39 inches) away from the TV
set or stereo sound sets.
Operation should be within its receiving range.
If the remote control does not operate normally, please
take the batteries out, and reinsert them 30 seconds later; if
If the main unit needs to be remote controlled, please
aim the remote controller at the receiver of the main unit in order
to improve the receiving signal to the unit.
When the remote controller sends out signal, a mark
will flicker for about One second. The chime will sound if the main unit
receives effective signal.
it is still not operating ,please replace the batteries.
to the polarity. (As shown in Fig 2.)
4. Attach the back cover of wireless remote control.
Sketch map for
changing batteries
-8-
MS-SVU052A-EN 04/14
Page 2
Remote control
NOTE: Not all functions are available on all units. Any unit function not supported by this remote
will sound a short beep.
This wireless remote control is universal and it could be used for many units.
X-FAN button
X-FAN
QUIET
●
Press this button to activate / deactivate
the TURBO function. When you start this
function, the unit will run at the highest
fan speed to quickly heat or cool so that
the room temperature reaches the desired
set point as soon as possible.
TURBO button
TURBO
●
Set point temperature can be increased.
button
Temperature range for Celsius degree
setting:16-30;for Fahrenheit degree
setting:61-86.
Press this button to increase the desired
temperature. Hold it down for more than
2 seconds to rapidly change the set point.
In AUTO mode, the temperature set point
is not adjustable (see MODE).
●
Set point temperature can be decreased.
button
Press this button to decrease desired
temperature. Hold it down for more than
2 seconds to rapidly change the set point.
in AUTO mode, the temperature set point
is not adjustable (see MODE).
Names and functions of wireless remote control
Operation of wireless remote control
QUIET button
● Press this button to toggle between the
Quiet mode functions. Auto Quiet mode
(displays and
signal) and Quiet
mode (displays signal) and Quiet OFF
( there is no signal of displayed),
when the unit is turned on, the Quiet
OFF mode is defaulted. In quiet mode
the unit will operate at the lowest fan
speed. Auto quiet will adjust the fan
speed automatically according to the
desired set point and will determine
if the indoor ambient temperature can
be achieved with the lowest fan speed.
● Press this key to enter the TIMER OFF
set up. (See TIMER ON instructions)
TIMER OFF
TIMER OFF button
●
Press the X -FAN button in COOL or DRY
mode.The icon is displayed and the
indoor fan will continue operation at low fan
speed for 10 minutes
after the unit is turned off.
This function allows removal of moisture on the
evaporator of the indoor unit after the unit has stopped.
After power on, X-FAN OFF is defaulted.
X-FAN is not available in AUTO,FAN or
HEAT mode.
-2-
“Auto”
MS-SVU052A-EN 04/14
TIMER ON
TIMER ON BUTTON
●
Remote control
Name and function of wireless remote control
Operation of wireless remote control
I FEEL BUTTON
●
Press this button to turn ON the I
FEEL function.
The unit will automatically adjust room temperature
according to the temperature sensed
at the remote controller. Press this
button again to cancel the I FEEL function.
NOTE: The remote controller must be
pointed at the indoor unit to assure
good communication. Transmitting range
is 30 feet. The indoor unit will check
the remote control signal every 10 minutes
for set point information. If the indoor
unit does not receive a signal within
11 minutes, temperature control will return
to the sensor on the indoor unit.
I FEEL
SWING LEFT AND RIGHT BUTTON
Press this button to initiate the auto-ON timer.
After pressing this button,
will disappear
and
"ON" will blink. "0:00" will
be displayed
for the start time setting. While
the icon is
blinking, press
to adjust the time
value. Every press changes the time setting
by 1 minute. Holding down either button will
rapidly change the time setting by 10 minute
intervals. Within 5 seconds after setting the
start time, press TIMER ON button to confirm.
To cancel the auto-timer program, simply press
this button again. Repeat these steps when
pressing the TIMER OFF button to set the timer
"OFF" time.
●
Press this button to set swing angl e,
which cycles through changes as below:
OFF
This remote controller is universal,
if any
command is sent out, the unit will carry
out the available command as the guide
louver swings through available options.
If guide louver is stopped when it is
swinging up
and down, it will remain in its
present position.
indicates guide louver swings back and
forth
in the five places, as shown in the
figure.
SWING UP AND DOWN BUTTON
●
Press this button to set left & right swing angle
cycling as below: (not available on all units)
OFF
-3-
NOTE: Not all functions are available on all units. Any unit function not supported by this remote
will sound a short beep.
This wireless remote control is universal and it could be used for many units.
or
HEALTHY AND SCAVENGING BUTTON
/
NOTE: This function is not available.
MS-SVU052A-EN 04/14
●
●
Name and function of wireless remote control
Operation of wireless remote control
SLEEP BUTTON
Press this button, to cycle through and select Sleep 1 (
),
Sleep 2 (
),
Sleep 3 ( ) and cancel sleep.
When unit is turned on, Sleep Cancel is defaulted.
Sleep 1 is Sleep
Mode 1,
available in
COOL and DRY
modes.
In this mode, after running
for one hour the main unit set point will
increase
1
．
At two hours, the set point will increase
2
run at this
temperature setting. In Heat
mode: In the heat
sleep mode after running
for one hour , the set point will decrease
1℃(2°F),
When the unit has
run for two
hours , the set point temperature will decrease 2℃(3°F),
then the unit will run at this temperature setting.
●
Sleep 2 is Sleep Mode 2. The air conditioner will run according to
the presetting sleep temperature curve.
In Cool mode:
(1) When setting the initial temperature 16-23 ,
after
turning on the Sleep function,
the temperature will be increased 1℃
every hour. After 3 hours
the temperature will be maintained, after
7 hours,the temperature will be decreased 1℃(2°F), after that the unit
will keep on running under this temperature.
(2) When setting the initial temperature 24℃～2
7 ,
after turning on the Sleep function, the temperature will be increased 1
℃(2°F)
every hour , after 2 hours
the temperature will be maintained, after 7
hours, the temperature will be dec reased 1℃(2°F), after that the
unit will keep on running under this temperature.
(3) When setting the initial temperature 28℃～2
9℃
(82°F～84°F)
,
after turning on the Sleep function, the temperature will be increased
1
℃
(1°F) every hour, after 1 hour
the temperature will be maintained,
after 7 hours the temperature will be decreased 1℃(2°F), a
fter that the
unit will keep on running under this temperature.
(4) When setting the initial temperature 30℃(86°F), under this tem-
perature setting, after 7 hours, the temperature will be
decreased
1
℃
(2°F), after that the unit will keep on running und
er this temperature;
In Heat mode:
(1)
After the initial set po
int temperature is
selected 16℃
(61°F)
,
the unit will run
under this temperature setting while the sleep setting is enabled.
(2)
After the initial set point temperature
is selected17℃～20℃
(63°F～68°F)
,
after Sleep function is selected the temperature will decrease 1℃
(2°F) every hour, after 1
℃(2°F)
this temperature
SLEEP
-4-
(2°F)
℃(61～73°F)
℃(75°F～81°F)
(
2°F)
will be maintained.
temperature is decreased,
NOTE: Not all sleep functions are available on all units. Most units will only operate
with Sleep Mode 1. Any function not supported by this remote will sound a short beep.
℃
(3°F), then the unit will
℃
MS-SVU052A-EN 04/14
Name and function of wireless remote control
Operation of wireless remote control
SLEEP BUTTON
(3)
After the init ial set point temperature is selected
21℃ ～27 ℃(70°F ～81°F),
when the Sl eep function is selected , the
temperatu re will decrea se 1℃(2°F)
every hour, after 2℃(3°F) has decreased, this temperature will be
(4)
After the initial set point temperature is selected 28℃～ 30℃ (82°F ～ 86°F),
maintained.
when the Sleep function is selected the temperature will
decrease 1℃(2°F) every hour, after 3℃(6°F) has decreased this
temperature will be maintained.
Sleep 3- the sleep curve setting under Sleep Mode by DIY:
(1) Under Sleep 3 mode, press and hold "TURBO" button, remote
control enters into user individuation sleep setting status, at this
time, the time of remote control will display "1 hour ", the setting
(2) Adjust and button, could change the corresponding
setting tem perature, a fter adjuste d, press "TURBO "button for
confirmation;
(3) At this time, 1 hour will be automatically increased at the timer
postion on the remote control, (that are "2 hours" or "3 hours"
(4) Repeat the above s tep (2)～(3) operation, until 8 hou rs
temperature setting finished, sleep curve setting finished, at this
time, the remote c ontrol will resume the original timer display;
temperature "88" will display the corresponding temperature of last
setting sle ep curve an d blink (The first ente ring will d isplay
according to the initial curve setting value of original factory);
or "8 hours "), the place of setting temperature "88" will
display the corresponding temperature of last setting sleep curve
and blink;
temperature display will resume to original setting temperature.
●
●
Sleep3- the sleep curve setting under Sleep Mode by DIY
be inquired:
The user could enter the sleep curve setting method to inquire
the presetting sleep curve, to enter into user individuation sleep
setting status, but not change the temperature, press "TURBO"
button directly for confirmation.
Note: In the above presetting or enquiry procedure,
if the remote
does not receive input within 10 seconds the sleep curve setting
status will be a
utomatically quit and resume the original
display. In the presetting or enquiry procedure, press "ON/OFF"
button, "Mode" button, "Timer"button or "Sleep" button, the sleep
curve setting or enquiry status will quit similarly.
SLEEP
-5-
MS-SVU052A-EN 04/14
Loading...