Trane MCX 512 GB, MCX 518 GB, MCX 524 GB, MCX 530 GB, MCX 536 GB Installation Manual

February 2009 MS-SVN015-EN

Installation Manual

NEW STYLUS

TM

Split System, 1-5 Tons
Convertible Type
MCX Series 50/60 Hz

50 Hz Models
Cooling Only

MCX 512 GB
MCX 518 GB
MCX 524 GB
MCX 530 GB
MCX 536 GB
MCX 042 GB
MCX 048 GB
MCX 060 GB

60 Hz Models
Cooling Only

MCX 512 G1
MCX 518 G1
MCX 524 G1
MCX 530 G1
MCX 536 G1
MCX 042 G1
MCX 048 G1
MCX 060 G1

60 Hz Models
Cooling/Heating

MCX 512 G1E
MCX 518 G1F
MCX 524 G1B
MCX 530 G1H
MCX 536 G1J
MCX 042 G1J
MCX 048 G1K
MCX 060 G1L

50 Hz Models
Cooling/Heating

MCX 512 GBE
MCX 518 GBF
MCX 524 GBB
MCX 530 GBH
MCX 536 GBJ
MCX 042 GBJ
MCX 048 GBK
MCX 060 GBL

MS-SVN015-EN.p65 2/17/09, 4:44 PM1

Black

MS-SVN015-EN

General Information

General Information

This Installation Manual is given as
a guide to good practice in the
installation by the installer of MCX
mini-split system. Installation
procedures should be performed in
the sequence that they appear in this
manual.

For installing the unit to operate
properly and reliably, it must be
installed in accordance with these
instructions. Also, the services of a
qualified service technician should
be employed, through the
maintenance contract with a
reputable service company.

Read these Installation Instructions
completely before installing the air
conditioning system.

About this Manual

Cautions appear at appropriate
places in this Instruction Manual.
Your personal safety and the proper
operation of this machine require
that you follow them carefully.
The Trane Company assumes no
liability for installations or servicing
performed by unqualified personnel.
All phases of the installation of this
air conditioning system must
conform to all national, provincial,
state and local codes.

About the Unit

These MCX units are assembled,
pressure tested, dehydrated,
charged and run tested before
shipment. The information contained
in this manual applies to MCX units
are designed to operate in cooling
mode only and in cooling or heating
modes.

Trane MCX series of mini-split
systems offer three styles of
installation: floor, low wall and under
ceiling with both LCD wireless
remote control or wired control.
Trane MCX series provide flexibility
and savings.
Note: For model MCX 042, MCX 048
and MCX 060, there are only two
styles of installation: under ceiling
and low wall.

Reception

On arrival, inspect the unit before
signing the delivery note. Specify any
damage of the unit on the delivery
note, and send a registered letter of
protest to the last carrier of the
goods within 72 hours of delivery.
Notify the dealer at the same time.

The unit should be totally inspected
within 7 days of delivery. If any
concealed damage is discovered,
send a registered letter of protest to
the carrier within 7 days of delivery
and notify the dealer.

Warning

Warnings are provided at
appropriate places in this manual to
indicate to installers, operators and
service personnel of potentially
hazardous situations which, if not
avoided, COULD result in death or
serious injury.

Caution

Cautions are provided at appropriate
places in this manual to indicate to
installers, operators, and service
personnel of potentially hazardous
situations which, if not avoided, MAY
result in minor or moderate injury or
malfunction of the unit.

Warranty

Warranty is based on the general
terms and conditions by country. The
warranty is void if the equipment is
modified or repaired without the
written approval of The Trane
Company, if the operating limits are
exceeded or if the control system or
the electrical wiring is modified.

Damage due to inappropriate
installation, lack of knowledge or
failure to comply with the
manufacturer’s instructions, is not
covered by the warranty obligation.
If the installation does not conform
to the rules described in Installation
Manual, it may entail cancellation of
warranty and liabilities by The Trane
Company.

Important

This document is customer property
and is to remain with unit. Please
place in service information pack
upon completion of work. These
instructions do not cover all
variations in systems, nor do they
provide for every possible
contingency to be met in connection
with installation. Should further
information be desired or should
particular problems arise which are
not covered sufficiently in this
manual, the matter should be
referred to your authorized Trane
dealer.

MS-SVN015-EN.p65 2/17/09, 4:44 PM2

Black

3MS-SVN015-EN

Contents

General Information 2
Typical Installation 4
Location and Preparation of Units 5
Unit Installation 6
Connection of Refrigerant Tubing 7
Condensate Drain Piping 9
Electrical Installation 10
Remote Control Installation 11
Typical Wiring Diagram 12
Dimensional Data 21
Notes 23

MS-SVN015-EN.p65 2/17/09, 4:44 PM3

Black

4 MS-SVN015-EN

Typical Installation

Note: For models MCX 042, MCX 048, MCX 060

there are only two styles of installation: under ceiling and low wall

Ceiling
mounted

Outdoor unit

Indoor unit

Floor mounted

Return air grille contains air filter

Refrigerant tubing/wiring

Drain

Return air grille
contains air filter

Supply air grille
Adjustable louvers direct air

Supply air grille
Adjustable louvers direct air

Low wall mounted

MS-SVN015-EN.p65 2/17/09, 4:44 PM4

Black

5MS-SVN015-EN

Location and Preparation of Units

1. Select an appropriate position
that allows every corners of the
room to be uniformly air
conditioned and where it is easy
to route the refrigerant tubing.

2. Ensure that the floor or ceiling
construction is sufficient to fully
support the weight of the indoor
unit.

3. Consideration must be given to
assure an unobstructed flow of
supply and return air.

4. Refrigerant tubes between
indoor and outdoor units should
be as short as possible.

5. Length of the condensate drain
hose should be kept as short as
possible (Figure 1).

6. Recommended service
clearance as shown in figure
2, 3 and 4.

7. Do not install unit in direct
sunlight or near other heat
sources as this may affect
performance. Do not allow
outside air to directly enter unit
or condensate may form at the
unit’s discharge.

Note: For MCX042-MCX060 the
unit should be installed over the floor
at least 20 cm.

Figure 4

Figure 3

Figure 2

Maintenance area

(Celling mounted)

Min.

30 cm.

Min.

20 cm.

Min.

20 cm.

Min.

30 cm.

Min.

20 cm.

Maintenance area
(Floor mounted)

Figure 1

Min. 120 cm.

Min.

30 cm.

Min.

20 cm.

Min.

20 cm.

Maintenance area

(Low wall mounted)

MS-SVN015-EN.p65 2/17/09, 4:44 PM5

Black

6 MS-SVN015-EN

0.83"(21)

0.83"(21)

8.5"(215)

B

A

Unit Installation

Indoor Unit

1. Select a location to route tubing,
wiring and drain pipe between
the indoor and outdoor units.

2. Make a hole in the wall using a
key hole saw or hole-cutting drill
attachment.
The hole should be made at a
slight downward slant to the
outdoor side (Figure 5).

Before cutting, check that no pipes
or studs are directly behind the
place to be cut. Avoid areas where
electrical wiring or conduits are
located.

3. Place the unit on a solid and level
foundation.

4. Tubing, wiring through and drain
pipe of low wall and floor
mounted units can be routed,
rear or right side of unit when
facing front.
Ceiling mounted can be routed
straight downward.

5.

Pull air filters upward (Figure 6).

Figure 5

6. Unscrew at the return grille
(Figure 7).

7. Unscrew at the grille bottom
hinges, pull out the screw, and
unscrew at the side panel front
(Figure 8). Then, push down on
the side

panel front and pull up

(Figure 9).

Note: = A 0.49" x 1.575" - 4 SLOT
(Mounting hole) (12.5 mm 40.0 mm)

Unit Size B
MCX 512-518

36.2" (920)

MCX 512GB5
MCX 524

46.1" (1,170)

MCX 518-524GB5
MCX 530-536

55.9" (1,420)

MCX 530GB5
MCX 042-048 65.7" (1,670)
MCX 536-042GB5

75.6" (1,920)

MCX 060

8. Place or hang the unit at the
selected position.

9. Replace both right and left side
panels, and the return grille after
the installation of wiring, tubing
and piping is complete.

Outdoor Unit

See the proper installation method
provided in the Installation Manual
for the outdoor unit.

Indoor side

Figure 6

Pull

Pull

Figure 7

Figure 8

Figure 9

Outdoor side

Figure 10

MS-SVN015-EN.p65 2/17/09, 4:45 PM6

Black

7MS-SVN015-EN

Connection of Refrigerant Tubing

The indoor unit refrigerant line
connections are flared both 50 Hz
and 60 Hz. Installation brazing, leak
testing, and evacuation of refrigerant
lines are covered in the Installer
Manual, packaged with the outdoor
unit. Read the instructions before
installing the refrigerant lines.

The indoor unit refrigerant piping
connections are located on the right
hand side when facing the unit
(Figure 11).

Connecting the unit with flaring
procedure.
(Only for MCX 512-536)

1. Flaring (If piping is procured or
cut at the site). Cut the copper
tube to the required length with
a tube cutter. It is recommended
to cut approx. 30-50 cm. longer
than the tubing length you
estimate.

2. Hold each pipe downward when
cutting and remove burrs at the
end of the copper tube with a
tube reamer or file. This process
is important and should be done
carefully to make a good flare
(Figure 12 and Figure 13).

Figure 11

Check if (L) is flared uniform
and is not cracked or scratched.
L Dimension:

1.4 to 1.7 mm (6.35 mm dia)

1.8 to 2.0 mm (9.53 mm dia)

1.9 to 2.2 mm (12.7 mm dia)

2.1 to 2.4 mm (15.88 mm dia)

When reaming, hold the tube end
downward and be sure that no
copper scraps fall into the tube.

3. Remove the flare nut from the
unit and be sure to mount it on
the copper tube.

4. Make a flare at the end of copper
tube with a flare tool (Figure
14, 15).

Copper
tubing

Reamer

Figure 12

Before After

Deburring

Figure 13

Flare tool

Flare nut

Copper
tubing

Figure 14

L

Figure 15

A good flare should have the
following characteristics:

- Inside surface is glossy and
smooth.

- Edge is smooth.

- Tapered sides are of uniform
length.

Bending

5. When bending the tube, be
careful not to crush it. To prevent
crushing of the tube, bend it
gently and do not bend the tube
at a radius curvature of less than
100 mm.

6. If the copper tube is bent or
pulled too often, it will become
stiff. Do not bend the pipe more
than three times at one place.

Cautions before
connecting tubes tightly

7. Be sure to apply a sealing cap or
water-proof tape to prevent dust
or water from getting into the
tubes before they are used.

8. Be sure to apply refrigerant
lubricant to the matching
surfaces of the flare and union
before connecting them
together. This is effective for
reducing gas leaks (Figure 16).

Apply refrigerant

lubricant here

Figure 16

MS-SVN015-EN.p65 2/17/09, 4:45 PM7

Black

8 MS-SVN015-EN

Connection

9. For proper connection, align the
union tube and flare tube straight
with each other, then screw in the
flare nut lightly at first to obtain a
smooth match (Figure 17).

10.

Tighten the flare nut to the
specified tightening torque with
torque wrench and adjustable
wrench (Figure 18).

Flare Nut Tightening Torque

Flare Nut/Piping Size Tightening Torque

kgf, - cm lbf-in

6.35 mm (1/4") dia. 150~200 130~170

9.53 mm (3/8") dia. 350~400 300~340

12.7 mm (1/2") dia. 500~550 430~470

15.88 mm (5/8") dia. 600~650 520~570

11. Repeat the process above for the
remaining line.

Connecting the unit with
brazing procedure
(Only for MCX 042-060)

1. Cut the copper tube to the
required length with a tube cutter.
It is recommended to cut approx.
20-30 cm. longer than the tube
length you estimate.

2. Remove burrs at the end of the
copper tube with a tube reamer
(Figure 12).

3. There are 2 ways to connect the
copper tube

- Use a coupling between the

copper tube of indoor unit and
the copper tube used for
installation (Figure 19).

- Expand the copper tube by

using a swaging tool set as in
Figure 20.

4.

Clean internal and external surfaces
of coupling or expanded tube prior
to brazing.

Figure 17

Figure 18

Figure 20

Figure 19

5. Insulate the entire gas line.

6. Do not allow uninsulated liquid
line to come in direct contact
with bare gas line.

7. Precautions should be taken to
avoid heat damage to the
pressure tap valve core during
brazing. It is recommended that
a wet rag be wrapped around the
valve body.

8. It is recommended to use braze
shield, soak pad in water and
place over suction and liquid
lines to protect unit finish.

9. To braze the copper tube, before
brazing a copper tube to a solder
coupling or a copper tube to an
expanded tube, do not forget to
keep them tight as shown in
Figure 21, 22.

10. Use a dry nitrogen purge and
brazing alloy without flux when
brazing the field line to the
copper factory connection. Flow
dry nitrogen into either valve
pressure tap port, through the
tubing and out the other port
while brazing.

11.Braze using accepted good
brazing techniques.

Copper tube of
outdoor unit

Solder coupling

Swaging

tool

Copper

tube

Tube holder

(Clamp)

Union Flare nut

Solder
coupling

C

O

M

M

E

T

3

Figure 21

To rc h

Copper tube
from indoor
unit

Solder rod

Copper tube from
outdoor unit

Solder
coupling

C

O

M

M

E

T

3

Figure 22

To rc h

Copper tube
from indoor
unit

Solder rod

Copper tube from
outdoor unit

Copper tube
of indoor unit

Indoor unit
pipe

Wrench
(adjustable)

Torque
wrench

Flare nut

Connection pipe

Connection of Refrigerant Tubing

MS-SVN015-EN.p65 2/17/09, 4:45 PM8

Black

9MS-SVN015-EN

Condensate Drain Piping

- The drain hose should run
straight down the wall to a
level where the runoff will not
stain the wall.

- There should be no traps.
Avoid putting the end of the
hose in water.

- To conveniently drain the
system, the drain hose must
slant downward, with a slope
of at least 1 : 50 to prevent
leakage. Figure 23 shows the
unit in the floor mounted
position.

- When the drain hose is placed
in the room, insulate the hose
with foam polyethylene to
avoid damage to the ceiling or
furniture.

- After completing installation of
refrigerant lines, wiring and
drain connections, bind the
tubing, wiring and drain hose
(check if local codes permit
binding) into a bundle by using
tape at 100 or 200 mm (4" to
8") intervals. Make sure the
drain hose is at the bottom of
the bundle (Figure 24).

Figure 24

Figure 23

Drain hose

Indoor unit

Slant

Drain hose

MS-SVN015-EN.p65 2/17/09, 4:45 PM9

Black

10 MS-SVN015-EN

Electrical Installation

All wiring and grounding must
comply with local electrical codes.

1. Wiring

Important Safeguards:

- Check the unit nameplate
for electrical rating.
Be sure wiring is done
according to local codes
and wiring diagram.

- Use a separate power line
with circuit breaker for each
air conditioning unit.

- Connect electrical ground
to all units.

- Wiring should not touch
refrigerant tubing,
compressor, motors or
moving parts.

- The manufacturer will
accept no responsibility for
problems caused by
unauthorized changes in
the internal wiring.

- Connect the wiring firmly.

2. Electrical Connections

See Section: Wiring System
Diagram

Indoor Unit

Remove the right side panel and
return grille (see previous
instructions), to access the terminal
base.

- Pass the system wiring
through the PVC pipe (both
power and control lines) to
interconnect indoor and
outdoor units.

- Connect the wire terminals to
the terminal base (see
connection indication on
system wiring diagram).

- Make sure all connections are
tight.

Outdoor unit

Outdoor Unit - Indoor Unit Electrical
Interconnection should be in
accordance with the applicable
system wiring diagram and indoor
unit diagrams.

Outdoor unit diagram are contained
in the outdoor unit Installer Manual.

Note:

- All wiring must comply with
national state and local codes.

- After completing the
connections, re-confirm them
to be in accordance with the
unit and system wiring
diagrams.

MS-SVN015-EN.p65 2/17/09, 4:45 PM10

Black

11MS-SVN015-EN

ECONOECONO

ON

FAN

COOL

DRY
HEAT
AUTO

OFF

POWERCOOL

SW

Z

Z

MODE

LOUVER

SWEEP

FRONT
BLADE

LIGHT

OFF

ON

POWER

COOL

ECONO

SLEEP

SEND

Locate and attach the
wireless remote control
and wired control as
follows:

1. Do not place the control and
the remote control near heat
sources or expose to the
direct rays of the sun.

2. Do not expose the control to
the indoor unit’s supply air
stream.

3. Do not place in a confined
space.

4. Attach the remote control
holder as shown in Figure 25,

26.

Remote Control Installation

Dimension

Wireless Remote Control Remote Control Mounting Bracket

Figure 25 Figure 26

TEMP

MENU

MODE

FAN

ON

ON OFF

OFF

ECONO

SW

SLEEP ECONO TURBO

TURBO

AUTO

14.5

4.0 X 2
SLOT

14.5

45.0

90.0

45.0

90.0

61.0

MS-SVN015-EN.p65 2/17/09, 4:45 PM11

Black

12 MS-SVN015-EN

Typical Wiring Diagram

J2

N

C1

C2

L

P20

J1

P17

P16

P19

P21

FREEZE

P22

P26

2

1

P3

LINE-C

EX-HI

P7

P6

P5

P4

LOW

MED

HI

NEUTRAL

P2

LINE

P1

BLK

BLU

RED

YL

BRW WHT

WHT

GRN/YL

WHT

RED

RED

BLK

BLU

RED

YL

INFRARED RECEIVER

GRN/YL

DESCRIPTION

COIL

BLK

RED

1. FREEZE SENSOR
LOCATED ON
EVAPORATOR COIL

2. TEMPERATURE
SENSOR LOCATED
IN RETURN AIR
STREAM

SWEEP MOTOR

(OPTION)

ROOM

STEPPER TOP STEPPER FRONT

DISPLAY

WIRELESS REMOTE

CONTROLLER

POWER SUPPLY
220-240VAC/1PH/50Hz
220-240VAC/1PH/60Hz

BLOWER

MOTOR

WIRING TO
GROUNDING SYSTEM

200-240 VAC CONTROL
WIRING TO OUTDOOR UNIT

FIELD WIRING

FACTORY WIRING

JUNCTION

TERMINAL BOARD

CAPACITOR

FUSE 3 AMP.

COLOR CODE

BLU BLUE
BLK BLACK
RED RED
WHT WHITE
GRN GREEN
YL YELLOW
BR BROWN

MCX512-042GB5 (50 Hz)

MCX512-536GB (50 Hz)

MCX512-536G1 (60 Hz)

INDOOR UNIT, COOLING ONLY WITH CONTROL TYPE “R”, 4 SPEED

MS-SVN015-EN.p65 2/17/09, 4:45 PM12

Black

13MS-SVN015-EN

Typical Wiring Diagram

MCX512-536GB (50 Hz) Standard Models

MCX512-536G1 (60 Hz) Standard Models

INDOOR UNIT, COOLING ONLY WITH CONTROL TYPE “R”, 3 SPEED

MS-SVN015-EN.p65 2/17/09, 4:45 PM13

Black

14 MS-SVN015-EN

Typical Wiring Diagram

MCX042-060GB (50 Hz) Standard Models

MCX042-060G1 (60 Hz) Standard Models

INDOOR UNIT, COOLING ONLY WITH CONTROL TYPE “R”, 3 SPEED

2

1

GRN/YL

1. FREEZE SENSOR
LOCATED ON
EVAPORATOR COIL

2. TEMPERATURE
SENSOR LOCATED
IN RETURN AIR
STREAM

P21

FREEZE

P22

P26

ROOM

DISPLAY

P3

LINE-C

P6

P5

P4

NEUTRAL

P2

LINE

P1

LOW

MED

HI

WHT

RED

RED

BLK

BLU

RED

INFRARED RECEIVER

P17

P16

BLK

RED

J2

J1

WHT

GRN/YL

BLK

BLU

RED

BLOWER

MOTOR

BRW WHT

WIRELESS REMOTE

CONTROLLER

POWER SUPPLY
220-240VAC/1PH/50Hz
220-240VAC/1PH/60Hz

WIRING TO
GROUNDING SYSTEM

200-240 VAC CONTROL
WIRING TO OUTDOOR UNIT

NC1

C2L

COLOR CODE

BLU BLUE
BLK BLACK
RED RED
WHT WHITE
GRN GREEN
YL YELLOW
BR BROWN

DESCRIPTION

COIL

FIELD WIRING

FACTORY WIRING

JUNCTION

TERMINAL BOARD

CAPACITOR

FUSE 3 AMP.

MS-SVN015-EN.p65 2/17/09, 4:45 PM14

Black

15MS-SVN015-EN

Typical Wiring Diagram

MCX512-042GB5 (50 Hz)

MCX512-536GB (50 Hz)

MCX512-536G1 (60 Hz)

INDOOR UNIT, COOLING ONLY WITH CONTROL TYPE “W”, 4 SPEED

GRN/YL

2

1

1. FREEZE SENSOR
LOCATED ON
EVAPORATOR COIL

2. TEMPERATURE
SENSOR LOCATED
IN RETURN AIR
STREAM

SWEEP MOTOR

(OPTION)

GRN/YL

STEPPER TOP STEPPER FRONT

P20 P19

P21

FREEZE

P22

ROOM

DISPLAY

P31

LINE-C

EX-HI

LOW

MED

HI

NEUTRAL

LINE

P3

P7

P6

P5

P4

P2

P1

WHT

RED

RED

BLK

BLU

RED

YL

P17

P16

BLK

RED

J2

J1

WIRE DISPLAY

BLK

BLU

RED

YL

WHT

BRW WHT

BLOWER

MOTOR

NC1

C2L

POWER SUPPLY
220-240VAC/1PH/50Hz
220-240VAC/1PH/60Hz

WIRING TO
GROUNDING SYSTEM

200-240 VAC CONTROL
WIRING TO OUTDOOR UNIT

BLU BLUE
BLK BLACK
RED RED
WHT WHITE
GRN GREEN
YL YELLOW
BR BROWN

COIL

FIELD WIRING

FACTORY WIRING

JUNCTION

TERMINAL BOARD

CAPACITOR

FUSE 3 AMP.

DESCRIPTION

COLOR CODE

MS-SVN015-EN.p65 2/17/09, 4:45 PM15

Black

16 MS-SVN015-EN

Typical Wiring Diagram

MCX512-536GB (50 Hz) Standard Models

MCX512-536G1 (60 Hz) Standard Models

INDOOR UNIT, COOLING ONLY WITH CONTROL TYPE “W”, 3 SPEED

MS-SVN015-EN.p65 2/17/09, 4:45 PM16

Black

17MS-SVN015-EN

Typical Wiring Diagram

MCX042-060GB (50 Hz) Standard Models

MCX042-060G1 (60 Hz) Standard Models

INDOOR UNIT, COOLING ONLY WITH CONTROL TYPE “W”, 3 SPEED

GRN/YL

P21

FREEZE

P22

ROOM

DISPLAY

P31

J2

GRN/YL

2

1

1. FREEZE SENSOR
LOCATED ON
EVAPORATOR COIL

2. TEMPERATURE
SENSOR LOCATED
IN RETURN AIR
STREAM

LINE-C

HI

LOW

MED

NEUTRAL

LINE

WIRE DISPLAY

P3P6P5

P4

P2

P1

WHT

RED

RED

BLK

BLU

RED

P17

P16

BLK

RED

J1

WHT

BRW WHT

BLK

BLU

RED

BLOWER

MOTOR

BLU BLUE
BLK BLACK
RED RED
WHT WHITE
GRN GREEN
YL YELLOW
BR BROWN

COIL

FIELD WIRING

FACTORY WIRING

JUNCTION

TERMINAL BOARD

CAPACITOR

FUSE 3 AMP.

NC1

C2L

POWER SUPPLY
220-240VAC/1PH/50Hz
220-240VAC/1PH/60Hz

200-240 VAC CONTROL
WIRING TO OUTDOOR UNIT

COLOR CODE

DESCRIPTION

WIRING TO
GROUNDING SYSTEM

MS-SVN015-EN.p65 2/17/09, 4:45 PM17

Black

18 MS-SVN015-EN

Typical Wiring Diagram

MCX512-536GB (50 Hz)

MCX512-536G1 (60 Hz)

INDOOR UNIT, COOLING/HEATER WITH CONTROL TYPE “R”, 4 SPEED

MS-SVN015-EN.p65 2/17/09, 4:45 PM18

Black

19MS-SVN015-EN

Typical Wiring Diagram

MCX512-536GB (50 Hz) Standard Models

MCX512-536G1 (60 Hz) Standard Models

INDOOR UNIT, COOLING/HEATER WITH CONTROL TYPE “R”, 3 SPEED

MS-SVN015-EN.p65 2/17/09, 4:45 PM19

Black

20 MS-SVN015-EN

Typical Wiring Diagram

MCX042-060GB (50 Hz) Standard Models

MCX042-060G1 (60 Hz) Standard Models

INDOOR UNIT, COOLING/HEATER WITH CONTROL TYPE “R”, 3 SPEED

MS-SVN015-EN.p65 2/17/09, 4:45 PM20

Black

21MS-SVN015-EN

Dimensional Data

OUTLINE DIMENSIONS

MCX512-530GB5 (EXPORT 50 Hz)
MCX512-536GB (EXPORT 50 Hz)
MCX512-536G1 (EXPORT 60 Hz)

MS-SVN015-EN.p65 2/17/09, 4:45 PM21

Black

22 MS-SVN015-EN

Dimensional Data

OUTLINE DIMENSIONS

MCX536-042GB5 (EXPORT 50 Hz)
MCX042-060GB (EXPORT 50 Hz)
MCX042-060G1 (EXPORT 60 Hz)

MS-SVN015-EN.p65 2/17/09, 4:45 PM22

Black

23MS-SVN015-EN

Notes

MS-SVN015-EN.p65 2/17/09, 4:45 PM23

Black

Literature Order Number: MS-SVN015-EN

Date: Feb 2009

Supersedes: Oct 2008

Stocking Location: Bangkok, Thailand

Trane has a policy of continuous product and product data improvement and reserves the right to change
design and specifications without notice.

For more information, contact your local district
office

‡∑√π (ª√–‡∑»‰∑¬)

·¢«ß¡—°°–—π ‡¢μ√“™‡∑«’ °√ÿ߇∑æœ 10400

‡≈¢∑’Ë 1126/2 Õ“§“√«“π‘™ 2 ™—Èπ 30-31 ∂ππ‡æ™√∫ÿ√’μ—¥„À¡à

Trane
www.trane.com

MS-SVN015-EN.p65 2/17/09, 4:45 PM24

Black