Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: (47)51 57 89 00 | Fax.: (47)51 57 89 50
E-mail: info@tranberg.com | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: (45) 75 85 83 80
E-mail: mail@tranbergsystems.com | www.tranbergsystems.com
TEF 9970 LED
HELIDECK FLOODLIGHT LIGHT
USER MANUAL
IMPORTANT
Read this instruction carefully before installing the
product
TUM 4605 REV. B 30.06.2015
TEF 9970 LED HELIDECK FLOODLIGHT USER MANUAL
INTRODUCTION
Thank you for purchasing this product!
For installation, maintenance and assurance of a long life
of this product, please follow this manual.
CONTENT IN BOX
The product is fully assembled, and ready for installation.
TOOLS REQUIRED
Regular tools required for installation.
• Tools for mounting, e.g. 13 mm wrench – to fasten the
mounting bracket to the deck and adjust the angle of
the lamp.
• 3 mm hexagon key (Unbraco/Allen key) for mounting
the lock to the termination compartment, and to loosen
the screws for the terminal assembly, if necessary.
• 32mm wrench to disassemble the blind plug and as-
semble the cable gland.
MAINTENANCE INSTRUCTIONS
The floodlight should be inspected according to Company routines. The manufacturer suggests regular check for
water intrusion in the termination compartment. The light
housing itself is a cemented EXd casing, so this will have no
technical concern.
When cleaning, use only mild detergents. Alcohol or petroleum based products may damage the gaskets.
APPLICATIONS
• Floodlight on helideck, general Floodlighting
• Zone 1, Zone 2 and safe area
APPROVALS
IECEx / ATEX CERTIFIED
II 2 G Ex d e op is IIB + H2 T4 Gb (T5 version available)
According to:
EN 60079-0:2012
EN 60079-7:2007
EN 60079-28:2007
EN 60079-1:2007
IEC 60079-0:2011
IEC 60079-7:2006
IEC 60079-1:2007
IEC 60079-28:2006
CE 0470
Warning – DO NOT OPEN WHEN ENERGIZED
Warning – THE M8 HEXAGON SOCKET BUT-
TONHEAD SCREW IN THE JUNCTION BOX
OF THIS LAMP SHALL NOT, UNDER ANY CIRCUMSTANCE, BE OPENED OR LOOSENED.
THIS WILL AFFECT THE FLAMEPROOF
PROPERTIES OF THE LAMP.
SAFETY PRECAUTIONS
Note that changes to the product and /or installation of
components which do not conform to the approval, may
be a safety violation. The manufacturer will not under any
circumstances be held responsible for such activity. For
your health and safety, always use safety gear suited for
the task. Be certain to follow codes, regulations and /or
specific procedures that are related to the installation. The
maximum temperature at the entry point of the cable exceeds 70°C, max temperature is 72°C. Make sure that the
cables and cable glands wich are used can withstand this
temperature.
When mounting the lid to the connection compartment,
make sure no cables or the safety wire are jammed between
the two parts. Check the gasket and make sure that the
gasket has no damages on the surface! This will dramatically reduce the ingress protection, and impair the mode
of protection regarding hazardous areas. When mounted,
there shall be no noticeable gap between the top and the
connection compartment. Not following these instructions
may lead to a risk of water ingress into the luminaire. The
manufacturer assumes no responsibility when these guidelines are not followed.
The terminals in this luminaire consist of a terminal block
for phase conductors and PE. Two M5 PE screws are fitted to accept PE cables. The terminal block is of the “Cage
clamp” type, and there is no need for a tool to connect or
disconnect the phase conductors. Nevertheless a large
screwdriver, preferably flathead, may be a good help.
TEF 9970 LED HELIDECK FLOODLIGHT USER MANUAL
INSTALLATION INSTRUCTIONS
Only qualified personnel are allowed to perform installation
and maintenance tasks to this product.
The equipment is ready for installation when leaving the
production facilities of Tranberg AS. Check the condition of
the equipment and the contents when unpacking. Any damage done to the equipment during transportation is not the
responsibility of Tranberg AS. If the content is not complete,
file a claim to the manufacturer immediately.
The TEF 9970 is delivered with several mounting options. A
mounting bracket for flat surfaces is standard. For the light
output to be in accordance with any regulations listed in this
document, the helideck floodlight must be mounted on a
horizontal surface coincident with the helideck.
The luminaire must always be installed in an upright position. Any other mounting positions should not be used for
permanent installation, without a confirmation from Tranberg’s technical department. If the luminaire is mounted on
a vessel or a floating installation, movements such as roll
and pitch, which moves the luminaire out of its original upright position, is not taken into account.
Mounting Details
997A108863
Make sure to use IECEx /ATEX approved cable glands, approved for the specific cable diameter and type, according
to the relevant standards listed in “APPROVALS” for group
IIB + H2. These data can be found in the cable gland datasheet and declaration of conformity. The cable gland shall
hold an IP grade of 66 or 66/67. The max and min. temperature for the cable gland shall be over +75°C and under
-55°C.
Stopping plugs and drain plug shall be IECEx/ATEX approved according to IEC 60079-0:2011, EN 60079-0:2012,
IEC 60079-7:2006, EN 60079-7:2007 for group IIB + H2 and
hold an IP grade of 66 or 66/67. The max and min. temperature shall be over +75°C and under -55°C.
Any damage caused by the use of an incorrect combination
of cable and cable gland is not the responsibility of Tranberg
AS and is not covered by warranty.
Termination
997A108807
Tranberg AS | P.O. Box 8033 | N-4068 Stavanger | Norway | Tel.: (47)51 57 89 00 | Fax.: (47)51 57 89 50
E-mail: info@tranberg.com | www.tranberg.com
Tranberg Systems | Hjulmagervej 15C | 7100 Vejle | Denmark | Tel.: (45) 75 85 83 80
E-mail: mail@tranbergsystems.com | www.tranbergsystems.com
TEF 9970 LED HELIDECK FLOODLIGHT USER MANUAL
TECHNICAL DATA
Material: Marine Aluminum – powder coated, Borofloat safety glass
Power consumtion: Approx. 45 W
Input voltage: 100-277VAC; 140-277VDC
Short-circuit current: 1500A @ 100-254V AC 47-63Hz
Expected lifetime: 50 000 h
Weight: 11 kg
IP rating: IP 66. (IP 67 without drain plug)
Cable entries: 2 PCS. M25 x 1.5 entries for IECEx / ATEX approved cable glands ac-
cording to IEC 60079-0:2011, EN 60079-0:2012, IEC 60079-7:2006,
EN 60079-7:2007 Delivered with Tranberg cable glands.
Ex classification: II 2 G Ex d e op is IIB + H2 T4 Gb (T5 version available)
Ex certificate no.: IECEx PRE 14.0060
Presafe 14ATEX5703
CE marking: CE 0470
Max surface temp.: <135°C
Tamb: -55°C to +55°C (+40°C for T5)
Manufacturer: Tranberg AS
Dimensions:
997A108285
Loading...