Tramigo T23 Magnum Quick Start Manual

T23 MAGNUM

CONFIGURATION

TIP:

Over 300,000 intersections, parks, public buildings and
other landmarks in your region are preloaded into your T23
Magnum device. Use the “ADDPLACE” command to add HQ,
office, destination pier or other important locations.

HQ

T23 MAGNUM CONFIGURATION

T23 Magnum Quick Start Guide V1.0

For firmware V.1.0.9

English Version

Magnum

Thank you for choosing Tramigo. This guide will help you get started with your T23 Magnum.

Copyright © 2014 Tramigo Ltd. Tramigo, M1 Move, T23, T23 Magnum, TLD, Tramigo

Landmarks and associated logos are trademarks of Tramigo Ltd. For more

infomation, visit our website at www.tramigo.com

Visit www.tramigo.com to check out the

free software for your T23 Magnum

Questions? Find us on Skype: Tramigosupport

or email us at [e-mail]

5 6

Getting started with your T23 Magnum

General Settings

Most common use is Internet data (GPRS) communication enabling reporting to
server side, like Tramigo M1 Fleet Enterprise. Following commands are needed:

1) Register as Owner

Owner

2) Name the T23 Magnum

Name,<name>

3) Optional: Add additional SMS user(s)
and grant the access level

AddUser,<phone number>,
<Owner/Friend/Guest>

4) Set the correct Mobile Operator
Access Point Name APN, the default
is INTERNET

GPRS,APN,<APN>,<username-optional
>,<password-optional>

5) Set the IP address and Port name

GPRS,Connect,<ip address>,<port>,TCP

6) Boot the T23 Magnum after all
commands given

Boot,Hard

Beacon Mode, Default

T23 Magnum has preloaded Beacon mode configuration. In this mode T23
Magnum is sending Location and Status report every 3 hours. It does not wake on
movement and responds received SMS and GPRS commands only during that
reporting time. Note: With command "LISTUSER" check the user number. For
GPRS data it is always #10. For SMS users it is #2 - #9.

You can change the 3 hours reporting interval, use following commands.

Changing the Location and Status reporting interval between 1-1440 minutes

Report,10,Find,<interval in minutes>
Report,10,Status, <interval in minutes>

Active Mode

T23 Magnum wakes on scheduled reports and motion. This mode is used if
desired to have trip reports and motion alarms. Between scheduled reports and
trips theT23 Magnum goes to battery saving mode and as in a Beacon mode it
responds to received SMS and GPRS messages only when it is awake.

Enable motion wakeup

Set,WakeOnShock,1
Set,IgnitionInputShock,1

Location and Status reporting every 5 minutes, 2 kilometers or if
heading change more than 30 degrees, and every 720 minutes when
parked.

Report,10,Find,5,2,720,30
Report,10,Status,5,2,720,30

Battery Life Estimates

Configuration and Usage

Beacon mode. Waking to report every 3 hours, no
motion and trip reports.

Beacon mode. Waking to report every 12 hours, no
motion and trip reports.

Active mode. Waking on movement, reporting every 6
hours and generates trip reports. Traveling an average
of 1-2 hours per day.

Active mode. Waking on movement, reporting every 12
hours and generates trip reports. Traveling an average
of 1-2 hours per day.

Battery Life

40 days

>40 days

20 days

Up to 30 days

Mandatory: Enable power saving with command "SET,SLEEP,1" after you have completed all
planned configuration changes.
Note: If command ResetSettings is given to T23 Magnum, all preloaded settings are lost.
Configuration files and support is available at [e-mail]

T23 Magnum Peru: parado, 0.09 km...

T23 Magnum Chile: Moviendose...

STEP 3: INSTALL

T23 Magnum is simple to install. It does not require any wiring.

Note: For best possible GPS lock always place T23 Magnum so that the Tramigo
Logo has clear view of the sky.

Your T23 Magnum requires a SIM card to communicate location messages using
the GSM network. This guide walks you through on how to setup and configure your
T23 Magnum.

Container Lock:

1) Register as the owner of your unit

2) Acquire satellite lock

2) Check indicator lights

1) Open T23 Magnum

3) Change your password (optional)

Velcro tape:

Find out more at www.tramigo.com

F

R

E

E

F

O

R

Y

O

U

S

M

A

R

T

P

H

O

N

E

O

R

T

A

B

L

E

T

R

TIP:

If there has been a need to supply
RESETSETTINGS command or is
required to set T23 Magnum back
to default settings contact to
[e-mail] and ask
the configuration files.

M1 Move makes tracking easy with
Tramigo Landmarks and visual maps.
Download for free by visiting

m.tramigo.net on your mobile and

following the installation instructions.

Experience M1 Move

2 3 4

STEP 1: SET UP

Correct
LED Status

STEP 2: CONNECT

If using a data-only SIM not able to send SMS messages, please refer to the GPRS

GUIDE.

Check that your SIM is not
protected by a PIN code - Insert
the SIM into a mobile phone.
Follow your phone instruction
manual to remove the PIN lock.

1) Open the cover

2) Insert SIM card

Slide the SIM card into place with the
contact surface facing down.

4) Charge battery

Use 4.2V Li-Po charger and
charge battery overnight.

TROUBLESHOOTING:

Not able to get SMS message response from the T23 Magnum.

“PASSWORD,0000,XXXX”

your old password

new password,
up to 20 characters long,
do not use spaces or
special symbols

Automotive standard hi-quality Velcro can be
used in certain cases, for example when
Magnum placed inside the vehicle's cockpit
or covert installation is not required.

T23 Magnum can be used with container lock. Designed for container tracking and
security. Further inquiries, please contact to [e-mail]

Open 6 screws to remove the cover and then open 4 screws holding the PCB and
PCB cover. Be careful not damaging the SIM card. Note: Be sure that no static
electricity present. It can damage the PCB board. Use Antistatic Wrist Strap.

Power light should blink green, no GSM red light and
no GPS blue light.

Use your mobile phone to send the text message “OWNER” to the mobile # of your
T23 Magnum. Your Tramigo will shortly reply to confirm you as the owner of the unit.
This also verifies that GSM is working.

Take T23 Magnum outdoors to a location with a clear view of the sky and place it so
that the Tramigo logo is up. Wait 5 minutes and send SMS message "STATUS". GPS
signal strength should be over 50%. At the same time you can check GSM signal
strength and battery status.

“0000” (four zeros) is the default password of your Tramigo. To prevent other people
from accessing your device, change the password into something only you know. To
change the password, send the following SMS to your unit:

Open 6 screws
to remove the
cover and take
the battery
aside.

3) Connect wires

Check that
battery and
charging wires
are connected.
Insert the
battery and
close the cover.

NOTE:

Magnum Battery cannot be charged using PCB's USB or IO
port. Magnum 4.2V Li-Po Wall Charger is directly charging the
battery. PCB's LED lights don't indicate the charging status.