How to install the Immobilizer
T22-IMMOBILIZERMAN 2.5
This installation guidance is for the Tramigo T22-IM MOBI LIZ ER 12 an d T2 2-IMMOBILIZER24.
The Immobilizer feature is used to disable a car’s ignition. This option requires special wiring
that must be done carefully to ensure trouble-free operation. With this feature active a car will
not start even if the T22 is removed.
IMPORTANT NOTICE:
This is an examplatory installation scheme only. Variation may be required depending to the type of vehicle
or machine to which T22 will be installed. All possible direct and indirect damages caused by the installation
are the sole responsibility of the installer or installing body. The installer or installing body is responsible to
test and ensure the functionality of their installation. All possible direct and indirect damages caused by the
use of the immobilizer are the sole responsibility of the end user . Tramigo Ltd’s manufacturer responsibility
is limited to the function of Tramigo T22 unit as stated in the warranty clause that can be found from the User
Manual and is not extended in any way for the installation done by a third party.
The installation should always be done only by professional mechanics, which have been properly trained to
install or service the Immobilizer. We recommend that you do NOT install the Immobilizer yourself, unless
you are a professional mechanic and knowledgeable about the Immobilizer.
The installer or installing body is responsible that the installation complies with local legislation. Additionally
if the Immobilizer is to be installed to a vehicle the installer, Installing body and the end user are responsible
to check the local legislation regarding t he execution of the immobilization command and comply with the
regulations. Extreme caution must always be used if the immobilization command is executed on a moving
vehicle. SMS can take a while to be received, so the vehicle may be in a dangerous location or travelling at a
high speed when the immobilizer is activated. Vehi cle’s engine will be shut down, power st eering will be lost
and the vehicle will be difficult to control.
The disable command is used to activate the immobilizer. Disable,on prevents the engine from
starting. This will occur immediately if the vehicle is parked or 45 seconds after the ignition has
been turned off, and vehicle is not in moving state. Disable,off allows the engine to start. You
must have SMS coverage to be able to use these commands. Disable,on,forced shall
immobilize the vehicle regardless of the vehicle state. Please use this command with extra
caution.
This feat ur e is supported by firmw ar e v1.54 or higher and T22i
Command:
Disable,on - immobilizer will engage only when it meets conditions
Disable,on,forced - immobilize the vehicle as soon as T22 receives the SMS.
Disable,off - immobilizer has been turned off and vehicle may function again.
Vehicle must have GSM coverag e f or these commands to work.
© Tramigo Ltd. All rights r eserved. U nder the copyright laws, this manual cannot be reproduced in any form
without the prior wr itten permiss ion o f Tramigo.
Page 1
How to install the Immobilizer
T22-IMMOBILIZERMAN 2.5
Conditions:
Car should be stopped or parked
Not moving
Car is not in trip mode*
Ignition is off
The immobilizer works as follows:
Note you have to use Ignition sensing with the immobilizer option.
Scenario 1:
Vehicle is parked, not in trip mode and ignition off.
(send “disable,on” command)
Result: Immobilizer takes effect immediately. Vehicle will not startup.
*not in trip mode – vehicle has been parked with ignition off for 15 minutes
Scenario 2:
Vehicle is moving.
(send “disable,on” command)
Result: Immobilizer will take effect when ignition has been switched off for 45 seconds and the
trip ends 15 minutes default.
Scenario 3:
Vehicle is immobilized and wont start.
(send “disable,off” command)
Result: Immobilizer will disengage. Vehicle may be started.
© Tramigo Ltd. All rights r eserved. U nder the copyright laws, this manual cannot be reproduced in any form
without the prior wr itten permiss ion o f Tramigo.
Page 2
How to install the Immobilizer
T22-IMMOBILIZERMAN 2.5
Installation:
Vehicle manufacturers warranty may be voided if the install is not done by their staff. Take
these instructions and parts to their service center for installation.
Requirements:
T22-IMMOBILIZER (example wirings for T22-IMMOBILIZER12 with petrol engine)
Note: It’s highly recommended to install an override switch located in a discreet place
where the owner can find it. This prevents them from getting stuck if there is a problem
with GSM coverage, T22, wiring, or the relay. T o use the owner presses the switch while
turning the ignition.
© Tramigo Ltd. All rights r eserved. U nder the copyright laws, this manual cannot be reproduced in any form
without the prior wr itten permiss ion o f Tramigo.
Page 3
How to install the Immobilizer
T22-IMMOBILIZERMAN 2.5
1. Configure your T22 for Immobilizer feature with SOS button.
Send the following commands via SMS or Tramigo Manager to your T22 which will have the
immobil i ze r feat ur e:
• set,input2,1
• set,input1,4
• set,HFMinPressTime,1
• set,SOSMinPressTime,5000
• set,IgnitionInputGPIO,1
• set,IgnitionInputShock,0
Tip: If you are installing many T22’s save these messages in your phone.
2. X & Y connect to GND. (You can join the 2 small black wires and use a single wire to GND.)
Make sure it is connected to the chassis of vehicle, and not to any assumed GND.
3. Cut the wire that activates the starter when Ignition is switched ON. Connect the
the
YELLOW immobilizer wires on the cut wires respectively.
GREEN and
When you cut the Ignition cable/wire
into two, test one end with multitester
(or even bulb), the side that gives
voltage or lig ht s up is for the
GREEN
wire and the other side staying blank
is for the
YELLOW
wire.
4. Tap the
BLUE wire to the Ignition line. This line should have the power ON always when the
engine is running.
5.
RED Wire (which has 15A fuse attached to it), connects directly to the vehicle power.
This can be the same to which T22-CAR red (positive) wire is connected.
NOTE: RED WIRE can be also connected to IGNITION to extend relay lifetime and to reduce
power co nsumptio n
6. X wire an d
BROWN wire are connected to an extra in pu t (SOS / Sensor / ATB butto n) which is
optional.
© Tramigo Ltd. All rights r eserved. U nder the copyright laws, this manual cannot be reproduced in any form
without the prior wr itten permiss ion o f Tramigo.
Page 4
Wirin g Diagram:
How to install the Immobilizer
T22-IMMOBILIZERMAN 2.5
NOTES:
1) Ignition sensing (BLUE WIRE) should be connected to the node/wiring, which ha s power on for
the whole driving trip, not only for cranking.
2) RED WIRE can be also connect ed t o IGNITION to extend relay lifet im e and to reduce pow er
consumption
© Tramigo Ltd. All rights r eserved. U nder the copyright laws, this manual cannot be reproduced in any form
without the prior wr itten permiss ion o f Tramigo.
Page 5
How to install the Immobilizer
T22-IMMOBILIZERMAN 2.5
Hints and Tips:
Add a hidden override switch to bypass the T22 immobilizer. - This would be useful if in
case you send a disable command. Then if the vehicle goes to a place where it has no
GSM signal, sending command to enable vehicle again won’t be possible. Also useful
should your T22 be taken away which will permanently disable you vehicle. You can
attach a switch / button to the white wires if you want to implement this.
You may want to disable sleep mode so that your vehicle is always online and ready.
When vehicle is in deep sleep mode it will not be able to process your request and may
not be able to receive your command.
There is IMMOBILIZER12 and IMMOBILIZER24 for 12V and 24V systems respectively.
To test your connection unplug the I/O cable from the T22, the vehicle should go off/won’t
start.
Three most common places for installing the immobilizer is the ignition, starter motor or
the fuel pump. For petrol engines you can use ignition and for diesel engines starter.
However, for forced stopping of the vehicle, fuel pump is the safest. For new cars not
applicable of the previous options, there can be a possibility to immobilize the vehicle
computer system or use the exi stin g immo bilizer.
Vehicle GND refers to any metallic part of the chassis.
Should there be some unclear details, pl ease emai l
support@tramigo.com
© Tramigo Ltd. All rights r eserved. U nder the copyright laws, this manual cannot be reproduced in any form
without the prior wr itten permiss ion o f Tramigo.
Page 6
Loading...