Instruction Manual
TKPC9000
INTRODUCTION
The TrakPower engine heater uses technology similar to
that used by Formula 1, Indy Car and NASCAR teams. It
will properly pre-heat your engine to 140-158˚F (60-70˚C)
in 10 minutes based on ambient temperatures.
The TrakPower Engine Heater will pre-heat all critical parts
of your nitro engine, giving you minimal stress and wear on
the engine. It helps relieve stress on the crankshaft, conrod, piston and sleeve during warm-up. It also gives you a
very easy and smooth engine start, with no stress on your
starterbox. Fuel consumption is much less, as you do not
have to spend time warming up and adjusting your engine.
A pre-heated glow plug will increase the life of your plug. It
is also perfect for break-in, as it reduces the “pinch” on your
new engine. You will experience that engine pre-heating
is a must. Most importantly, it will quickly pay for itself by
increasing engine life and performance!
SPECIFICATIONS
Input Voltage 12VDC
(12VDC power supply or 3S LiPo)
Heating Power 90W
Heating Time 10 minutes
Low Voltage Cutoff 9.0V (3.0V per cell)
LED Indicator Heating:
Solid blue LED
Low Voltage Cutoff:
Flashing blue LED
Weight 65g
Dimensions Diameter: 63mm
Height: 50mm
● Very small, lightweight and compact for quick and
easy storage
● It is designed to transfer heat effectively and
effi ciently
● Access port on top allows you to start and monitor
your engines temperatures without having to
remove the heater
HOW TO USE
1. Place the engine heater over the cylinder head.
2. Connect the power cord to a DC power source or 3S
LiPo battery.
3. Push white power button. The LED will turn blue and
the engine heater will begin heating the engine for 10
minutes. If the desired temperature is not reached within
10 minutes, push the power button again to heat for an
additional 10 minutes.
4. To turn off the heater during the heating process, push
and hold the power button for more than 3 seconds and
the heater will stop.
5. Disconnect the DC power source and remove the heater
from the engine. CAUTION: The heater and engine will
be HOT.
6. Now you are ready to start your pre-heated engine.
WARNING: NEVER APPLY POWER TO THE
ENGINE HEATER IF IT IS NOT MOUNTED ON
AN ENGINE. IT WILL OVERHEAT AND POTENTIALLY
DAMAGE THE ENGINE HEATER.
SAFETY NOTES
SPECIAL FEATURES
● MCU control heating time and heating power for
maximum safety
● Safety timer: turn off power around 10 minutes
automatically
● LED indicator for status of engine heater
● 12V DC source with low voltage cutoff
● Fireproof and heat resistant adjustable cover
● Fits all .19-.26 RC nitro engines
● Before using every time be sure the heater element,
cord, plug and PCB are in good condition. If any of
these items are damaged, do NOT use the product.
● Do not pull, twist or bend the cord.
● NEVER leave the heater on unattended.
● ALWAYS unplug the heater before starting your
engine.
● NEVER refuel your car with the heater connected.
● Store the heater in a safe area. After use, the
heater will still be hot. Allow heater to cool before
storing.
● This is an electrical product. It can result in
dangerous shock and fi re. Please use caution when
using this product.
WARRANTY
TrakPower warrants this product to be free from defects in
materials and workmanship for a period of 120 days from
the date of purchase. During that period, we will repair or
replace, at our option, any product that does not meet these
standards. You will be required to provide proof of purchase
date (receipt or invoice). If, during the warranty period, your
motor shows defects caused by abuse, misuse or accident,
it will be repaired or replaced at our option, at a service
charge not greater than 50% of the current retail list price.
Be sure to include your daytime telephone number in case
we need to contact you about your repair. This warranty does
not cover components worn by use, application or reverse
voltage, cross connections, poor installation, subjection of
components to foreign materials, or tampering. In no case
shall our liability exceed the original cost of the product.
Your warranty is voided if:
● You apply an input voltage that exceeds the
maximum specifi cations of the engine heater.
● You allow water or moisture to enter the engine
heater.
● You attempt to modify or tamper this engine heater.
Under no circumstances will the purchaser be entitled to
consequential or incidental damages. This warranty gives
you specifi c legal rights, and you have other rights which
vary from state to state.
For service to your TrakPower ESC, either in or out of
warranty, send it post-paid and insured to:
Hobby Services (217) 398-0007
3002 N. Apollo Dr. Suite 1
Champaign, IL 61822
Email: hobbyservices@hobbico.com
© 2014 TrakPower, a Hobbico® company.
TKPC9000
Loading...