Traeger Elite BBQ 07E Owner's Manual

TRAEGER

®

OWNER’S MANUAL

BBQ 07E

“Elite”

RESIDENTIAL PELLET GRILL

This Grill Protected Under Patent Number: 4,823,684

FOR OUTDOOR USE ONLY!

DO NOT STORE OR USE NEAR GASOLINE OR OTHER
FLAMMABLE OR COMBUSTIBLE LIQUIDS IN THE
VICINITY OF THIS APPLIANCE! USE ONLY TRAEGER
BRAND HARDWOOD BBQ PELLETS IN THE
OPERATION OF THIS UNIT.

W ARNING!

INTRODUCTION

Congratulations on your purchase of this TRAEGER WOOD PELLET GRILL,
Model 07E Lil’ Tex “Elite”. With proper set-up, operation and maintenance, this

grill will provide you with years of cooking enjoyment.

Your new grill comes almost completely assembled. You will need to complete
the assembly which includes:

1) Mounting the side box (23) onto the main barbecue body (2)

2) Mounting the smoke stack (1) onto the main barbecue body (2)

3) Positioning the U-shaped firepot cover (5) over the firepot (10), and setting
the angled drip pan (6) in place.

4) Attach

5) Attach the rear wheels to the barbecue body (27)

6) Hanging the grease bucket (22) on the grease drain tube hook (16) located
on the grease drain tube.

NOTE : NUMERALS FOLLOWING PART NAMES THROUGHOUT THIS
MANUAL REFER TO THE COMPONENT DIAGRAM ON THE PREVIOUS
PAGE.

When you un-box your grill, make sure you have, and can identify all of the
following parts:

(1) Bag of nuts, washers, and bolts. These are for mounting
the pellet hopper/firepot, smokestack and handle to the
barbecue.
(1) Main barbecue body (2)
(1) Pellet hopper/firepot (23)
(2) Viper Casters (29)
(2) Wheels (27)
(1) Porcelain coated cooking grill (4). Remove for assembly
(1) U-shaped firepot cover (5). Remove from grill for assembly
(1) Angled drip pan (6). Remove from grill for assembly
(1) Grease catch bucket (22)
(1) Smokestack (1)

Follow these step by step instructions and you’ll be cookin’ in no time!

TOOLS REQUIRED FOR ASSEMBLY

7/16” open-end wrench or an adjustable crescent wrench.
A Phillips screwdriver or screw gun with a Phillips screw driver bit
1/4" Allen wrench

SECTION ONE: ASSEMBLY INSTRUCTIONS

MOUNTING THE PELLET HOPPER/FIREPOT:

1) Slide the side box (23) square tube into the square opening located on the left
side of the main barbecue body (2).Gently push the firepot into the body until
the pellet hopper is snug against the main barbecue body (2).

2) Align the bolt holes (21) on the side box with the bolt holes on the barbecue
body (2).

3) Insert the four ¼ inch bolts (21) from the inside main barbecue body into the nut
zerts (24) found on the right side of the pellet hopper/firepot box. Place a
washer over each bolt and screw into the nut zert (24). Use a socket wrench
to tighten bolts. DO NOT OVER TIGHTEN BOLTS.

INSTALLING THE SMOKE STACK:

Attach the smokestack (1) onto the right hand end of the main

barbecue body using the bolts, washers and nuts supplied. Washers should
be placed between the bolt head and barbecue body on the outside. A
washer should also be placed on the
bolt inside the barbecue body prior
to threading the nut onto the bolt.

Wheel

INSTALLING THE WHEELS:

Install wheels as shown in diagram.
Do not over tighten the bolt.

Leg Zert

¼ inch Allen bolt

Washer