OPERATOR’S MANUAL
TP-9362
Carbon Monoxide Meter
Declaration of Conformity
This is to certify that this equipment, designed and supplied
by Tracer Products, a division of Spectronics Corporation, 956
Brush Hollow Road, Westbury, New York 11590, USA, meets
the essential safety requirements of the European Union and
is placed on the market accordingly. It has been constructed in
accordance with good engineering practice in safety matters
in force in the Community and does not endanger the safety of
persons, domestic animals or property when properly installed
and maintained and used in applications for which it was made.
Equipment Description PRO-Chek CO™ Carbon
Monoxide Meter
Applicable Directives 73/23/EEC as amended
by 93/68/EEC
89/336/EEC as amended
by 93/68 EEC
Applicable Standards EN 61010-1: 1993 EN 61326:
2000-11, EMC Cl A,
Immunity Criteria B
CE Implementation Date January 2005
Any questions relative to this declaration or to the safety of
this product should be directed, in writing, to Tracer Products’
Customer Service Department at the address above.
3
Introduction
The Tracerline® PRO-Chek CO™ Carbon Monoxide Meter
measures the presence of carbon monoxide (CO), indicating the
gas’s concentration in atmosphere between the values of 1-999
parts per million.
Do not use the PRO-Chek CO as a personal safety monitor.
CAUTION
The PRO-Chek CO should be recalibrated yearly.
Operating Instructions
1. Remove the battery access door and install the 9 volt alkaline
battery.
2. Turn ON the meter by pressing the right hand button. The
meter will give you a short beep to indicate the power has been
turned ON.
3. The PRO-Check CO will take 30 seconds to run through a selfcheck and warm-up. During this period, the display will indicate
the time remaining before the meter is ready for operation.
4. The PRO-Check CO should be turned ON in an area known
to be free of carbon monoxide contamination. The meter will
automatically establish a zero point during start-up. However,
if the ambient concentration of carbon monoxide is higher than
3 ppm during the zero process, the meter will not reset the zero
point and will indicate the carbon monoxide concentration level.
4
Display Features
• Digital readout of parts per million concentrations in 1 ppm
increments
• Low battery indicator (appears with approximately 1 hour lifetime
remaining)
• MAX indicator when meter is in maximum display mode
• Concentration indicators per the following chart:
2-9 ppm Yellow
10-34 ppm Orange
35 ppm or higher Red
Audible Outputs
• Short beep when PRO-Chek CO is turned ON.
• Two short beeps when meter is warmed up and ready to take
readings
• Geiger counter-like tick when concentration of CO is between
35-200 ppm (frequency increases with increasing concentration
of CO)
• Constant alarm when concentration moves above 200 ppm
• Two short beeps when meter shuts down after 20 minutes of
operation.
• Two short beeps when shut down because of a low battery.
Maximum Reading Mode
When in the maximum reading mode, the PRO-Chek CO will
display the maximum reading it measures. Press the left hand
MAX button and the meter will display the maximum carbon
monoxide concentration measured after the meter was put into
maximum mode. MAX will appear on PRO-Chek CO‘s display
when in maximum mode. All display and audible features are still
active when in maximum mode.
5
Automatic Power Off
The PRO-Chek CO automatically turns off after 20 minutes.
When starting up after an automatic shut down, the concentration
reading the meter was displaying when shut down will fl ash for 5
seconds before the meter returns to reading the concentration in
real time.
Specifi cations
Usage Indoor or outdoor
Pollution degree 2
Humidity 90% RH NC max
Overvoltage category 2
Battery One 9 volt alkaline
Altitude 2000 m
Battery life 200 hours
Weight 9.0 oz (250 g)
Operating temperature 32 to 110 °F (0 to 43 °C)
Storage temperature 14 to 122 °F (-10 to 50 °C)
Concentration range 0 to 999 ppm CO
Accuracy 1 ppm ±3% of reading
Warranty and Liability
Your PRO-Chek CO Carbon Monoxide Meter is of the fi nest
design and craftsmanship. As such, Tracer Products warrants that
when delivered it will be free from defects in manufacture.
Tracer Products’ obligation under this warranty is limited to
repairing or replacing, at the option of Tracer Products, any
part(s) of the product which, if properly installed, used and
maintained, proves upon factory examination to have been
defective in materials or workmanship within two years from the
date of delivery.
6
Tracer Products does not warrant items that deteriorate under
normal use, including batteries. In addition, Tracer Products does
not warrant any instrument that has been subjected to misuse,
negligence or accident, or has been repaired or altered by anyone
other than Tracer Products.
This warranty is in place of all other warranties of quality. There
are no other warranties either oral, written, express, implied or
statutory. IMPLIED WARRANTIES OF FITNESS FOR PURPOSE
AND MERCHANTABILITY ARE EXCLUDED. This warranty and
your remedies thereunder are solely as stated in this manual.
In no event shall Tracer Products be liable for special, indirect,
incidental or consequential damages, nor for any damages arising
out of delay in shipment or production.
Return Authorization Procedure
A defective PRO-Chek CO should be returned to your wholesaler
for warranty evaluation. If you have any questions, please contact
the Customer Service Department at Tracer Products.
NOTE: Do not return your defective unit directly to the factory
without fi rst contacting Tracer Products for a Return Authorization
Number.
7
AM08047
074-410-P34
Printed in U.S.A.
Loading...