®
TP-8100 UV/Blue
™
12-Volt, ‘‘Instant On’’ Leak Detection Lamp
U.S. Patents 5,816,692 and 5,905,268
IMPORTANT SAFETY INSTRUCTIONS
1.Read all instructions.
2.Care must be taken as burns can occur from touching hot parts.
3.Do not operate the lamp with a damaged cord or if the lamp has been damaged.
4.Do not let the cord hang over edge of table, bench or counter, or come in contact with hot manifolds or moving fan blades.
5.To protect against risk of fire, do not operate the lamp in the vicinity of open containers of fuel (gasoline).
6.Adequate ventilation should be provided when working on operating combustion engines.
Do not use below garage floor or grade level.
Ne pas utiliser en fosse ou en dessous du niveau du sol.
SAVE THESE INSTRUCTIONS
WARNING
RISK OF EXPLOSION. This equipment has internal arcing or sparking parts that should not be exposed to flammable
vapors. It should be located in an area providing at least four air changes per hour, or should be located at least 18
inches above the floor.
OPERATION
1. Turn off the engine before performing any leak detection inspections.
2. Add fluorescent dye to the system to be inspected (use OEM-approved Fluoro-Lite®and Dye-Lite®dyes for best results).
See dye instructions for full information.
3. Do not look directly into the UV/blue light. You must wear the fluorescence-enhancing glasses supplied with the lamp to
protect your eyes and to make leaks clearly visible.
4. Connect the battery clips to any 12-volt vehicle battery or regulated 12 VDC, 3 amp (minimum) power source — red clip to the
positive (+) terminal and black clip to the negative (-) terminal.
5. Press the rocker switch and pivot the lamp head to the desired position.
6. Scan the system with the lamp. Leaks will show with a bright yellow or green fluorescent glow.
7. Use the lamp in low-light conditions for best performance.
WARNING
Intermittent, short inspection intervals will reduce heat buildup and extend bulb life. Use for a maximum of 5 minutes,
after which allow a 15-minute cooling interval. Allow the lamp to cool to the touch before restarting. Do not touch the
glass filter lens during use. Do not secure the momentary ON/OFF switch in the ON position. This will void the lamp’s
warranty.
CAUTION
Always disconnect the lamp from the power source and allow it to cool before storing or disassembling.
Do not operate the lamp without the filter lens attached. Unfiltered UV can be hazardous to the eyes and skin.
FOR LONGER BULB LIFE AND
• Do not touch the TP-8110 bulb or TP-8211 filter lens with your fingers. Finger oil on the bulb or filter lens will decrease
the light output and cause early bulb failure. Wear cotton gloves or use a soft cloth to avoid touching the bulb or filter
l e n s .
• After extensive use, the filter lens may require cleaning. Gently wipe the inside of the lens with a clean cloth. See
instructions below, “To Replace the Filter Lens.”
MAXIMUM LIGHT OUTPUT
A98253-7
TO REPLACE THE FILTER LENS
Use only the TP-8211 filter lens.
1. Remove the rubber filter holder and discard the old filter lens.
2. Using a clean cloth, press the new filter lens into the filter holder. Make sure that the side of the lens with the dot faces t o w a r d
the bulb.
3. Reattach the filter holder.
TO REPLACE THE BULB
Use only the 35-watt TP-8110 bulb.
Using any other bulb may damage the lamp and will void the warranty.
1. Remove the filter holder, the bulb guard and the old bulb.
2. Holding the new bulb by the edge of the reflector, press it into the two-pin socket firmly but gently.
3. Reattach the bulb guard and filter holder.
WARRANTY
The warranty policy for the TP-8100 lamp is provided on the Certificate of Limited Warranty enclosed separately with each unit.
NOTE: For assistance of any kind, contact the Customer Service Department at Tracer Products. In the U.S. and Canada, call toll-
free 1-800-641-1133. Give full details of the difficulty and include the model and serial numbers of the unit and the date of purchase.
If return of the unit to the factory is deemed necessary, shipping instructions will be provided. If an estimate of charges for nonwarranty work or other service work is required, a quote will be furnished upon evaluation of the unit. Out-of-warranty service work will
not be performed without customer approval.
Filter Holder
TP-8211
Filter Lens
Bulb Guard
35-Watt Bulb
TP-8110
Magnet
Rocker Switch
Cord with Battery Clips
12/99 A98253-7
PRINTED IN U.S.A.
Loading...