Traceable 18004-29, 18004-28, 18004-30, 18004-12 User manual

INSTRUCTIONS
IMPORTANT NOTICE
You MUST download one of the Mobile Apps below to retrieve data and configure device
Bluetooth ONLY
Download TraceableGO™ App
Bluetooth + Cloud Data Storage
TraceableLIVE® Subscription REQUIRED
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
NOW that one of the apps below have been
installed on your mobile device
TraceableGO comes ready to use out of the box.
Contents:
How to Configure Device using Mobile App .............................. 3-4
How to Download Data to your Mobile Device ..............................5
Device Specifications .................................................................. 6-7
TraceableGO™ App Free Download
FREE
Features
Congure datalogger:
▪ Set Alarm Change Logging Interval
Toggle between °C/°F Start/Stop Options ▪ Memory Wrap
Export, Email and Save PDF to Mobile Device
UNLIMITED CLOUD DATA STORAGE
Data download to CSV, or Secured
PDF
TraceableLIVE® App Free Download
$30/month
Features
Congure datalogger:
▪ Set Alarm Change Logging Interval
 
Toggle between °C/°F Start/Stop Options ▪ Memory Wrap
Export, Email and Save PDF to Mobile Device
UNLIMITED CLOUD DATA STORAGE
Data download to CSV, or Secured
PDF
Graphical UI to analyze data
Summary data display: Min/Max,
Kinetic Mean, Time in Alarm
Storage of trip parameters
Graphical UI to analyze data
Summary data display: Min/Max,
Kinetic Mean, Time in Alarm
Storage of trip parameters
2
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
CONFIGURE DEVICE
NOTE: To congure device either TraceableGO™ or
TraceableLIVE® Apps must be downloaded to a mobile device.
ENABLE BLUETOOTH
1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for ONE MINUTE, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol disappears, or quick press twice again to disable Bluetooth.
TO VIEW PRE-CONFIGURED SETTINGS
1. Enable Bluetooth on device (see above).
2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device. Note: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.
3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.
Scan for Nearby Devices
A list of available Dataloggers will appear.
Note: TraceableGO Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.
4. Once device is selected select Congure.
5. The following parameters are congured through App: START Mode, STOP Mode, ALARM Enable/Disable, Celsius/Fahrenheit, Memory Mode, Data Logging Interval, Alarm Setting.
6. TraceableGO™ comes pre-programmed. To view current
settings, tap on congure once device is selected in App.
7. Device comes pre-congured as shown below:
Device Name Device Serial Number Current Battery Status Current Temperature and/or Humidity Readings
PRE-CONFIGURED DEVICE SETTINGS
1. START Mode: Push Start
2. STOP Mode: Push Button Stop
3. Memory Mode: Wrap when
Memory is Full
4. Unit Preferences: °C
Alarm Setting Alarm Low:
TAP ON VALUE TO CHANGE
▪ Temperature: 2°C (6535 only) ▪ Temperature: 20°C (6537 only) ▪ Humidity: 25% RH (6537 only)
6. Alarm Setting High Alarm:
TAP ON VALUE TO CHANGE
▪ Temperature: 8°C (6535 only) ▪ Temperature: 30°C (6537 only) ▪ Humidity: 75% RH (6537 only)
7. Alarm Enable/Disable: Enabled
8. Data Logging Interval: 5 minutes
9. Date/Time is also set to current
to central time (Automatically updates when connected to mobile device).
3
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
CONFIGURE DEVICE (continued)
Tap Congure to change factory settings
1. START Mode
Immediate Start: Once device is congured it will begin
Datalogging. Push Button: Press START/STOP Button to begin Datalogging. Delayed: Select number of Hours, Minutes and Seconds when device is to begin Datalogging.
2. STOP Mode
Never: Device will never stop Datalogging.
Push Button: Press START/STOP Button to Stop Datalogging.
3. Memory Mode
Wrap When Full: Once memory is full, oldest data points will be overwritten with new data points. Stop When Full: Device will stop recording when Memory is Full 64K (65,536) data points, 7.5 months on 5-minute logging interval.
4. Unit Preferences
°F: Select Fahrenheit °C: Select Celsius
5. Alarm Setting Alarm Low: TAP ON VALUE TO CHANGE
▪ Temperature: Set LOWEST Temperature before an
alarm is triggered.
▪ Humidity (6537 only): Set LOWEST Relative Humidity
before an alarm is triggered.
6. Alarm Setting High Alarm: TAP ON VALUE TO CHANGE
▪ Temperature: Set HIGHEST Temperature before an
alarm is triggered.
▪ Humidity (6537 only): Set HIGHEST Relative Humidity
value before an alarm is triggered.
7. Alarm Enable/Disable
Enabled: Alarm is on. Disabled: Alarm is off.
8. Data Logging Interval
Slide to desired Logging Interval.
9. Save Congurations: Saves the current settings.
NOTE: Saving a Conguration will delete all data on
device.
Once device has been congured, device enters
STANDBY Mode.
Date/Time is also set to current to central time
(Automatically updates when connected to mobile device).
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
4
HOW TO DOWNLOAD DATA TO MOBILE DEVICE
NOTE: To download data either TraceableGO™ or TraceableLIVE
Apps must be downloaded to a mobile device.
ENABLE BLUETOOTH
1. Quick press twice START/STOP to enable Bluetooth, and Bluetooth LCD symbol appears.
2. Device starts to advertise to be found, and to be connected. Device Name shown on TraceableGO™ App discovered list looks like CC653X-xxxx, where “CC653X” indicates model number and “-xxxx” is last 4 digits of device serial number.
3. If no connection has been made for ONE MINUTE, Bluetooth will be disabled to save battery life, and Bluetooth LCD symbol disappears, or quick press twice again to disable Bluetooth.
TO DOWNLOAD RECORDED DATA
1. Device must be stopped. Enable Bluetooth on device (see above).
Note: TraceableGO™ Bluetooth Dataloggers are serialized and each logger name will match the sticker located on the side of the unit.
4. Once device is selected select Download Data.
5. App will begin extracting the data from TraceableGO™ Device.
2. Open TraceableGO™ or TraceableLIVE® App on any bluetooth enabled mobile device. Note: Mobile device must have Bluetooth enabled to receive signal. To enable Bluetooth on a mobile device see mobile device settings.
3. Use TraceableGO™ or TraceableLIVE® App to connect to device. Once the app is open it will begin searching for devices to connect to.
Scan for Nearby Devices
A list of available Dataloggers will appear.
6. Once data download is complete, mobile device
will display options how to send PDF le, or CSV le
(TraceableLIVE only). Tap Done and download is complete.
5
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
SPECIFICATIONS
Cat. No. 6535 Cat. No. 6538 Cat. No. 6537
TEMPERATURE
6535: Ambient Range: –20.0 to 70.0°C (–4.0 to 158.0°F) 6536/6538 Probe Range: –50.0 to 70.0°C (–58.0 to 158.0°F) 6539 Probe Range: –90.00 to 100.00°C (–130.00 to 212.00°F)
Resolution: 0.1°C Accuracy:
6535: ±0.4°C between −10 and 70°C, otherwise ±0.5°C 6536/6538: ±0.3°C 6539: ±0.2°C
RELATIVE HUMIDITY & TEMPERATURE Temperature— Ambient Range: –20.0 to 70.0°C (–4.0 to 158.0°F) Resolution: 0.1°C Accuracy: ±0.4°C between –10 and 70°C, otherwise ±0.5°C
Relative Humidity— Ambient Range: 0% to 95%RH, non-condensing Resolution: 0.1% RH Accuracy: ±3% RH between 5 to 75%, otherwise ±5% RH
EXTERNAL PROBE
6536 Bullet Probe: Standard plastic probe sensor with cable. Designed for use in air and
liquids, the sensor and cable may be completely immersed. Probe size: 3/16” diameter, 4/5” length; 10 foot cable
6538 Bottle Probe: Designed to simulate the temperature of stored liquids, use
in transportation coolers, refrigerators and freezers. Bottle probes are lled with a
patented nontoxic glycol solution that is GRAS (Generally Recognized As Safe) by the FDA (Food and Drug Administration) eliminating concerns about incidental contact with food or drinking water. The included micro-thin probe cable permits refrigerator/freezer
doors to close on it. (Do not immerse bottle probes in liquid). Probe size: 1 x 2-1/2 inches; 10 foot cable.
6539 Stainless-Steel/Platinum Probe: Detachable stainless steel 316 Probe with Platinum Sensor and 9 feet of cable are supplied with the unit. Probe has a diameter of
1/8-inch, stem length of 6-1/4 inches, overall length of 9 inches.
Battery: 2 AAA Alkaline batteries (3.0V)
Dimension: L x H x D: 3.5 x 2 x 0.79” (89 x 51 x 20 mm)
Battery Level Indication:
Battery level LCD symbol
≥ 80% (2.78V)
≥ 60% (2.56V), < 80%
Note: Battery level is updated every 5 minutes.
Note: Once battery level drops to below 10%, device may not work properly. Replace
batteries immediately.
Note: When replacing batteries, after removing the old batteries, wait 10 seconds before
inserting new batteries. Otherwise, Bluetooth may not work properly.
MEASUREMENT READING UPDATE FREQUENCY
Temperature and Humidity: 5 seconds;
Note: If a reading is out of operating range, corresponding location on LCD will display ‘--.-‘, and such out of range reading will not trigger alarm.
DATA LOGGING FREQUENCY:
5 min by default, user-adjustable between 1 minute and 12 hours with 1 minute step.
DATA STORAGE CAPACITY Alarm: Most recent 90 Alarm events
Data: 64K (65536) data points, 7.5 months on 5-minute logging interval
DEVICE OPERATING MODES
IDLE Mode: First time battery inserted, and device has not been congured
STANDBY Mode: Device has been congured, but not started;
RUN Mode: Device starts to measure and log data.
STOP Mode: Device stops from RUN Mode. In STOP Mode, device does not update measurements or log data, and the last measurements are displayed.
VIEW CURRENT READING
1. Temperature ONLY unit: Current reading, minimum/maximum reading, run time/alarm time toggling, Memory mode are shown on LCD.
2. Humidity and Temperature unit: Current temperature/humidity reading toggling every 5 seconds, minimum/maximum reading since last clearing, run time/alarm time, Memory mode are shown on LCD.
VIEW CURRENT MIN/MAX
Temperature ONLY unit: Current temperature Min/Max values are displayed on LCD. Humidity and Temperature unit: Current temperature/humidity Min/Max values are toggled
display.
Note: Every time device is congured, or resumes to run from STOP Mode, Min/Max
values are reset.
VIEWING RUN TIME/ALARM TIME
Run Time/Alarm Time is toggled to display on LCD. If Run Time is displayed, LCD symbol
RUN TIME appears; if Alarm Time is displayed, LCD symbol ALARM TIME appears.
Note: Alarm Time is accumulated for both Low Alarm and Hi Alarm for each channel
(temperature, humidity).
≥ 40% (2.34V), < 60%
≥ 20% (2.12V), < 40%
≥ 10% (2.01V), < 20%
< 10% Flashing
6
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Figure 3
Figure 3
Figure 4
SPECIFICATIONS (continued)
MEMORY
If Memory Mode is set to WRAP WHEN FULL, is set to STOP WHEN FULL, MEM appears on LCD.
ALARM
1. Once an alarm is triggered by any of temperature, humidity out of set alarm range, LCD symbol LOW ALM and/or HI ALM starts to ash. An Alarm Event will be logged.
2. Pressing START/STOP once will clear alarm, LCD symbol stops ashing. An Alarm Acknowledge Event will be logged.
3. If temperature, or humidity falls back to normal range, an Alarm Event will be logged. If any of temperature, humidity measurement goes back to out of alarm range, alarm will be triggered again.
4. If device’s START Mode is congured as PUSH BUTTON TO START (default), device LCD displays ‘push to start’. Press and hold START/STOP until LCD symbol appears.
Device enters RUN Mode. If device’s START Mode is congured as IMMEDIATE START, device enters RUN Mode immediately. If device’s START Mode is congured
as DELAYED TIME START, delayed start time set by user is counting down on device
LCD. Once the counting time reaches 0, device enters RUN Mode.
5. If in RUN Mode, LCD symbol RUN appears, and logs data at user-dened interval. If STOP Mode is congured as PUSH BUTTON TO STOP, press and hold START/
STOP until LCD symbol STOP appears. Device enters STOP Mode. If STOP Mode
is congured as NEVER STOP, device will ignore button press, and will stop when memory is full if Memory Mode is set to STOP WHEN FULL, or will stop when
TraceableGO™ App is connected to device and downloads the data.
6. If in STOP Mode, press and hold START/STOP until LCD symbol RUN appears. Device enters RUN Mode and resumes to log data at current setting. Anytime device resumes to log data from STOP Mode, Min/Max values are reset.
Note: If device in STOP Mode, START Mode will be set to PUSH BUTTON TO START regardless of previous Start Mode Setting. If Delayed Start Mode is needed while device in
STOP Mode, device must be re-congured.
Note: While device is connected to TraceableGO™ App, once Device has received
command from App to upload data to App, device will stop logging data and enter STOP Mode if it is still in RUN mode.
VIEW MEMORY USAGE, CURRENT DATE/TIME, DEVICE’S SERIAL NUMBER
1. Press and release START/STOP button
2. Memory usage in percentage is shown on LCD. The percentage indicates how much internal data memory storage has been used;
3. Number of days, hours, minutes left till memory is full are also displayed on the second line;
appears on LCD; If Memory Mode
Note: If Memory Mode is set to WRAP WHEN FULL: LCD symbol
on the display when the memory is full. Once memory is full, the oldest data points will be overwritten with new data points.
If Memory Mode is set to STOP WHEN FULL: LCD symbol MEM starts to ash on the display when the memory is 95% full. Once memory is full, the device will stop logging new
data points.
CLEAR DATA MEMORY STORAGE
1. Data points stored in device internal storage can only be cleared through App or battery removal.
2. Each time device is congured, all stored data points will be cleared.
3. Run Time/Alarm Time are also reset.
REGULATORY INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Hereby, Traceable Products, declares that this digital thermometer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes
: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
starts to ash
NOTE:
THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICA-
4. Within 10 seconds, press START/STOP again, current date/time is displayed on device
LCD. The following gure shows 9/14/2017, 17:30
TIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLI­ANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
W
5. Within 10 seconds, press START/STOP again, device S/N will be displayed on LCD.
6. To return to normal working status, press START/STOP again, or wait for 10 seconds and device will automatically go back to normal working status.
7
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
Loading...