TP Link WR720NV2 User Manual
TL-WR720N
150Mbps Wireless N Router
REV2.0.0
1910011176
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.
I
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
National restrictions
This device is intended for home and office use in all EU countries (and other countries following
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark
Bulgaria None
Outdoor use limited to 10
France
Italy None
Luxembourg None
mW e.i.r.p. within the band
2454-2483.5 MHz
General authorization required for outdoor use and
public service
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
If used outside of own premises, general authorization is
required
General authorization required for network and service
supply(not for spectrum)
Norway Implemented
Russian Federation None Only for indoor applications
Note: Please don’t use the product outdoors in France.
This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
II
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne doit pas provoquer d’interférences et
(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements:
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率
射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
III
安全諮詢及注意事項
● 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
● 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
● 注意防潮，請勿將水或其他液體潑灑到本產品上。
● 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
● 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
● 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA US
IV
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 150Mbps Wireless N Router
Model No.: TL-WR720N
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.8.1
EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 61000-3-2: 2014
EN 61000-3-3: 2013
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011
EN 50385: 2002
The product carries the CE Mark:
Person is responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2014
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
TL-WR720N 150Mbps Wireless N Router
CONTENTS
Package Contents .......................................................................................................................... 1
Chapter 1. Introduction................................................................................................................. 2
1.1 Overview of the Router................................................................................................. 2
1.2 Conventions ................................................................................................................. 2
1.3 Main Features .............................................................................................................. 3
1.4 Panel Layout ................................................................................................................ 4
1.4.1 The Front Panel................................................................................................ 4
1.4.2 The Rear Panel ................................................................................................ 5
Chapter 2. Connecting the Router ............................................................................................... 6
2.1 System Requirements.................................................................................................. 6
2.2 Installation Environment Requirements........................................................................ 6
2.3 Connecting the Router ................................................................................................. 6
Chapter 3. Quick Installation Guide............................................................................................. 8
3.1 TCP/IP Configuration ................................................................................................... 8
3.2 Quick Installation Guide ............................................................................................... 9
Chapter 4. Configuring the Router ............................................................................................ 15
4.1 Login .......................................................................................................................... 15
4.2 Status ......................................................................................................................... 16
4.3 Quick Setup................................................................................................................ 16
4.4 WPS........................................................................................................................... 16
4.5 Network
......................................................................................................................
19
4.5.1 LAN................................................................................................................. 29
4.5.2 WAN ............................................................................................................... 20
4.5.3 MAC Clone ..................................................................................................... 29
4.6 Wireless ..................................................................................................................... 30
4.6.1 Wireless Settings............................................................................................ 31
4.6.2 Wireless Security............................................................................................ 33
4.6.3 Wireless MAC Filtering ................................................................................... 37
4.6.4 Wireless Advanced......................................................................................... 39
4.6.5 Wireless Statistics........................................................................................... 40
4.7 DHCP ......................................................................................................................... 41
4.7.1 DHCP Settings ............................................................................................... 41
4.7.2 DHCP Clients List........................................................................................... 42
I
TL-WR720N 150Mbps Wireless N Router
4.7.3 Address Reservation ...................................................................................... 43
4.8 Forwarding ................................................................................................................. 44
4.8.1 Virtual Servers................................................................................................ 44
4.8.2 Port Triggering ................................................................................................ 46
4.8.3 DMZ................................................................................................................ 48
4.8.4 UPnP .............................................................................................................. 49
4.9 Security ...................................................................................................................... 50
4.9.1 Firewall ........................................................................................................... 50
4.9.2 IP Address Filtering......................................................................................... 51
4.9.3 Domain Filtering ............................................................................................. 53
4.9.4 MAC Address Filtering .................................................................................... 54
4.9.5 Local Management ......................................................................................... 56
4.9.6 Remote Management ..................................................................................... 57
4.9.7 Advanced Security.......................................................................................... 58
4.10 Parental Control ......................................................................................................... 59
4.11 Access Control ........................................................................................................... 62
4.11.1 Rule ................................................................................................................ 62
4.11.2 Host ................................................................................................................ 69
4.11.3 Target.............................................................................................................. 71
4.11.4 Schedule......................................................................................................... 73
4.12 S
t
atic Routing ............................................................................................................. 75
4.13 IP QoS........................................................................................................................ 76
4.14 IP & MAC Binding....................................................................................................... 77
4.14.1 Binding Settings.............................................................................................. 77
4.14.2 ARP List.......................................................................................................... 79
4.15 Dynamic DNS............................................................................................................. 80
4.15.1 Comexe.cn DDNS .......................................................................................... 80
4.15.2 Dyndns.org DDNS .......................................................................................... 81
4.15.3 No-ip.com DDNS ............................................................................................ 82
4.16 System Tools .............................................................................................................. 82
4.16.1 Time Settings.................................................................................................. 83
4.16.2 Diagnostic....................................................................................................... 85
4.16.3 Firmware Upgrade.......................................................................................... 86
4.16.4 Factory Defaults ............................................................................................. 87
4.16.5 Backup & Restore........................................................................................... 88
4.16.6 Reboot............................................................................................................ 88
II
TL-WR720N 150Mbps Wireless N Router
4.16.7 Password........................................................................................................ 89
4.16.8 System Log..................................................................................................... 90
4.16.9 Statistics ......................................................................................................... 92
Appendix A: FAQ.......................................................................................................................... 94
Appendix B: Configuring the PCs............................................................................................... 99
Appendix C: Specifications....................................................................................................... 102
Appendix D: Glossary................................................................................................................ 103
III
TL-WR720N 150Mbps Wireless N Router
Package Contents
The following items should be found in your package:
TL-WR720N 150Mbps Wireless N Router
Power Adapter for TL-WR720N 150Mbps Wireless N Router
Quick Installation Guide
Resource CD for TL-WR720N 150Mbps Wireless N Router, including:
This Guide
Other Helpful Information
Note:
Make sure that the package contains the above items. If any of the listed items is damaged or
missing, please contact with your distributor.
-1-
TL-WR720N 150Mbps Wireless N Router
Chapter 1. Introduction
1.1 Overview of the Router
The 150Mbps Wireless N Router delivers exceptional range and speed, which can fully meet the
need of Small Office/Home Office (SOHO) networks and the users demanding higher networking
performance.
The TL-WR720N 150Mbp
other 802.11n wireless clients. The incredible speed makes it ideal for handling multiple data
streams at the same time, which ensures your network stable and smooth. The performance of
this 802.11n wireless Router will give you the unexpected networking experience at speed 650%
faster than 802.11g. It is also compatible with all IEEE 802.11g and IEEE 802.11b products.
Multiple Security Protections
With multiple protection measures, including SSID broadcast control and wirele
64/128/152-bit WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), as well as
advanced Firewall protections, the TL-WR720N 150Mbps Wireless N Router provides complete
data privacy.
The TL-WR7
network administrators can establish restricted access policies for children or staff. It also
Incredible Speed
s Wireless N Router provides up to 150Mbps wireless connection with
ss LAN
Flexible Access Control
20N 150Mbps Wireless N Router provides flexible access control, so that parents or
supports Virtual Server and DMZ host for Port Triggering, and then the network administrators can
manage and monitor the network in real time with the remote management function.
Simple Installation
Since the Router is comp
manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in
this user guide. Before installing the Router, please look through this guide to know all the
Router’s functions.
atible with virtually
all the major operating systems, it is very easy to
1.2 Conventions
The Router or TL-WR720N mentioned in this guide stands for TL-WR720N 150Mbps Wireless N
Router without any explanation.
-2-
TL-WR720N 150Mbps Wireless N Router
1.3 Main Features
Make use of IEEE 802.11n wireless technology to provide a wireless data rate of up to
150Mbps
One 10/100M Auto-Negotiation RJ45 WAN port, two 10/100M Auto-Negotiation RJ45 LAN
ports supporting Auto MDI/MDIX
Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security
Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet
access
Up to 4 SSIDs supporting multiple wireless networks with different SSIDs and passwords
Supports Virtual Server, Special Application and DMZ host
Supports UPnP, Dynamic DNS
Provides Automatic-connection and Scheduled Connection on certain time to the Internet
Connects Internet on demand and disconnects from the Internet when idle for PPPoE
Built-in NAT and DHCP server supporting static IP address distributing
Supports Stateful Packet Inspection
Supports Parental Control and Access Control
Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List)
Supports Flow Statistics
Supports firmware upgrade and Web management
-3-
TL-WR720N 150Mbps Wireless N Router
1.4 Panel Layout
1.4.1 The Front Panel
Figure 1-1 Front Panel sketch
The Router’s LEDs and the WPS button are located on the front panel (View from left to right).
Name Status Indication
Off Power is off.
（Power）
(System)
(WLAN)
(LAN1,2)
(WAN),
(WPS)
On Power is on.
Flashing The Router is working properly.
On /Off The Router has a system error.
Off The Wireless function is disabled.
Flashing The Wireless function is enabled.
Off There is no device linked to the corresponding port.
On
Flashing There is an active device linked to the corresponding port.
Slow Flash
On
Quick Flash
There is a device linked to the corresponding port but
there is no activity.
A wireless device is connecting to the network by WPS
function. This process will last in the first 2 minutes.
A wireless device has been successfully added to the
network by WPS function.
A wireless device failed to be added to the network by
WPS function.
Table 1-1 The LEDs description
Note:
After a device is successfully added to the network by WPS function, the WPS LED will keep on
for about 5 minutes and then turn off.
-4-
TL-WR720N 150Mbps Wireless N Router
1.4.2 The Rear Panel
Figure 1-2 Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
WPS/RESET: This button is used for both WPS and Reset function. To use the WPS function,
press it for less than five seconds; to use the RESET function, press it for more than five
seconds.
Used as RESET button:
There are two ways to reset to the Router's factory defaults:
1) Use the Factory Defaults function on System Tools -> Factory Defaults page in the
Router's Web-based Utility.
2) Use the Factory Default Reset button: With the Router powered on, press and hold the
RESET button (at least 5 seconds) until the SYS LED becomes quick-flash from
slow-flash. Then release the button and wait the Router to reboot to its factory default
settings.
Used as WPS button:
WPS: If you have client devices, such as wireless adapters, that support Wi-Fi Protected
Setup, then you can press this button to quickly establish a connection between the Router
and client devices and automatically configure wireless security for your wireless network.
POWER: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this TL-WR720N 150Mbps Wireless N Router.
WAN : The WAN port is where you will connect the DSL/cable Modem, or Ethernet.
LAN (1-2): These ports connect the Router to the local PC(s).
Wireless antenna: To receive and transmit the wireless data.
-5-
TL-WR720N 150Mbps Wireless N Router
Chapter 2. Connecting the Router
2.1 System Requirements
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet.)
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
TCP/IP protocol on each PC
Web browser, such as Microsoft Internet Explorer 5.0 , Netscape Navigator 6.0 or above
2.2 Installation Environment Requirements
Place the Router in a well ventilated place far from any heater or heating vent
Avoid direct irradiation of any strong light (such as sunlight)
Keep at least 2 inches (5 cm) of clear space around the Router
Operating Temperature: 0~40 (32 ~104 )
Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1. Power off your PC, Cable/DSL Modem, and the Router.
2. Locate an optimum location for the Router. The best place is usually at the center of your
wireless network. The place must accord with the Installation Environment Requirements
.
3. Connect the PC(s) and each Switch/Hub in your LAN to the LAN Ports on the Router, shown
Figure 2-1
in
. (If you have the wireless NIC and want to use the wireless function, you can
skip this step.)
4. Connect the DSL/Cable Modem to the WAN port on the Router, shown in
Figure 2-1.
5. Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet. The Router will start to work automatically.
-6-
6. Power on your PC and Cable/DSL Modem.
TL-WR720N 150Mbps Wireless N Router
Figure 2-1 Hardware Installation of the 150Mbps Wireless N Router
-7-
TL-WR720N 150Mbps Wireless N Router
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your 150Mbps Wireless N
Router using Quick Setup Wizard within minutes.
3.1 TCP/IP Configuration
The default domain name of the 150Mbps Wireless N Router is http://tplinkwifi.net, the default IP
address is 192.168.0.1, and the default Subnet Mask is 255.255.255.0. These values can be
changed as you desire. In this guide, we all use the default values for description.
Connect the local PC to the LAN ports of the Router, and then you can configure the IP address
for your PC by following the steps below:
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: Configuring the
PC.
2) Then the built-in DHCP server will assign IP address for the PC.
Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and the Router. The following example is in Windows XP OS.
Open a command prompt, and type ping 192.168.0.1, and then press Enter.
If the result displayed is similar to the
and the Router has been established well.
Figure 3-1
, it means the connection between your PC
Figure 3-1 Success result of Ping command
-8-
TL-WR720N 150Mbps Wireless N Router
If the result displayed is similar to the
and the Router failed.
Figure 3-2,
it means the connection between your PC
Figure 3-2 Failure result of Ping command
Please check the connection following these steps:
1. Is the connection between your PC and the Router correct?
Note:
The 1/2 LEDs of LAN ports which you link to on the Router and LEDs on your PC's adapter should
be lit.
2. Is the TCP/IP configuration for your PC correct?
Note:
If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of
192.168.0.2 ~ 192.168.0.254.
3. Try the IP address 192.168.1.1.
Note:
If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the
Router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in
order to verify the network connection between your PC and the Router, you can open a
command prompt, and type ping 192.168.1.1, and then press Enter.
3.2 Quick Installation Guide
With a Web-based (Internet Explorer or Netscape® Navigator) utility, it is easy to configure and
manage the 150Mbps Wireless N Router. The Web-based utility can be used on any Windows,
Macintosh or UNIX OS with a Web browser.
-9-
TL-WR720N 150Mbps Wireless N Router
1. To access the configuration utility, open a web-browser and type the default address
http://tplinkwifi.net
in the address field of the browser.
Figure 3-3
After a moment, a login window will appear, similar to the Figure 3-4. Enter admin for the User
Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
Login the Router
Figure 3-4 Login Windows
Note:
If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go
to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel
the Using Proxy checkbox, and click OK to finish it.
2. After successfully log in, you can click the Quick Setup to quickly configure your Router.
Figure 3-5 Quick Setup
-10-
TL-WR720N 150Mbps Wireless N Router
3. Click Next, and then WAN Connection Type page will appear as shown in Figure 3-6.
Figure 3-6 Choose WAN Connection Type
The Router provides Auto-Detect function and supports three popular ways PPPoE,
Dynamic IP and Static IP to connect to the Internet. It’s recommended that you make use of
the Auto-Detect function. If you are sure of what kind of connection type your ISP provides,
you can select the very type and click Next to go on configuring.
4. If you select Auto-Detect, the Router will automatically detect the connection type your ISP
provides. Make sure the cable is securely plugged into the WAN port before detection. The
appropriate configuration page will be displayed when an active Internet service is
successfully detected by the Router.
If the connection type detected is PPPoE, the next screen will appear as shown in
Figure 3-7.
Figure 3-7 Quick Setup – PPPoE
User Name and Password - Enter the User Name and Password provided by your ISP.
These fields are case sensitive. If you have difficulty with this process, please contact
your ISP.
-11-
TL-WR720N 150Mbps Wireless N Router
Confirm Password - Re-enter the password provided by your ISP to ensure the
Password you entered is correct. If the Password is different from the Confirm Password,
the screen will appear as shown below. Click OK, and re-enter the Password and
Confirm Password.
If the connection type detected is Dynamic IP, the next screen will appear as shown in
Figure 3-9.
If the connection type detected is Static IP, the next screen will appear as shown in
Figure 3-8.
Figure 3-8 Quick Setup - Static IP
IP Address - This is the WAN IP address as seen by external users on the Internet
(including your ISP). Your ISP will provide you with the IP address you need to enter here.
Enter the IP address into the field.
Subnet Mask - The Subnet Mask is used for the WAN IP address. Your IPS will provide
you with the subnet mask which is usually 255.255.255.0.
Default Gateway - Your ISP will provide you with the Gateway address which is the ISP
server’s address. Enter the gateway IP address into the box if required.
Primary DNS - Enter the DNS Server IP address into the box if required.
Secondary DNS - (Optional) If your ISP provides another DNS server, enter it into this
field.
-12-
TL-WR720N 150Mbps Wireless N Router
5. Click Next to continue, the Wireless settings page will appear as shown in Figure 3-9.
Figure 3-9 Quick Setup – Wireless
Wireless Radio - Enable or disable the wireless radio by choosing from the drop-down
list.
SSID - Enter a value of up to 32 characters. The same name of SSID (Service Set
Identification) must be assigned to all wireless devices in your network. Considering
your wireless network security, the default SSID is set to be TP-LINK_XXXXXX
(XXXXXX indicates the last unique six numbers of each Router’s MAC address). This
value is case-sensitive. For example, TEST is NOT the same as test.
Channel - This field determines which operating frequency will be used. The default
channel is set to Auto, so the AP will choose the best channel automatically. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point.
Mode - This field determines the wireless mode which the Router works on.
Channel Width - Select any channel width from the drop-down list. The default setting
is automatic, which can automatically adjust the channel width for your clients.
-13-
TL-WR720N 150Mbps Wireless N Router
Disable Security - The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the Router without encryption. It is
strongly recommended that you choose one of following options to enable security.
WPA-PSK/WPA2-PSK - Select WPA based on pre-shared passphrase.
PSK Password - You can enter ASCII or Hexadecimal characters.
For ASCII, the key can be made up of any numbers from 0 to 9 and any letters from
A to Z, and the length should be between 8 and 63 characters.
For Hexadecimal, the key can be made up of any numbers from 0 to 9 and letters
from A to F, and the length should be between 8 and 64 characters.
Please also note the key is case sensitive, which means that upper and lower case
keys will affect the outcome. It would also be a good idea to write down the key and
all related wireless security settings.
No Change - If you choose this option, wireless security configuration will not change!
These settings are only for basic wireless parameters. For advanced settings, please refer to
Section 4.6: Wireless
.
6. Click the Next button. You will then see the Finish page.
If you don’t make any changes on the Wireless page, you will see the Finish page as shown
in Figure 3-10. Click the Fi
nish button to finish the Quick Setup.
Figure 3-10 Quick Setup – Finish
If there is something changed on the Wireless page, you will see the Finish page as shown
in Figure 3-11. Click the Reboot button to make your wi
reless configuration take effect and
finish the Quick Setup.
Figure 3-11 Quick Setup - Finish
-14-
TL-WR720N 150Mbps Wireless N Router
Chapter 4. Configuring the Router
This chapter will show each Web page's key functions and the configuration way.
4.1 Login
After your successful login, you will see the main menu on the left of the Web-based utility. On the
right, there are the corresponding explanations and instructions.
The detailed explanations for each Web page’s key function are listed below.
-15-
TL-WR720N 150Mbps Wireless N Router
4.2 Status
The Status page provides the current status information about the Router. All information is
read-only.
Figure 4-1 Router Status
4.3 Quick Setup
Please refer to Section 3.2: Quick Installation Guide.
4.4 WPS
This section will guide you to add a new wireless device to an existing network quickly by WPS
(Wi-Fi Protected Setup) function.
-16-
TL-WR720N 150Mbps Wireless N Router
a). Choose menu “WPS”, and you will see the next screen (shown in Figure 4-2 ).
Figure 4-2 WPS
Current SSID – The router supports multi-SSID and you can choose one SSID which you
want to configure its WPS function from the drop-down list. For example, if your wireless
client wants to connect to one of the router’s SSID “TP-LINK_E3C860” by WPS，you should
select TP-LINK_E3C860 as Current SSID.
WPS Status - Enable or disable the WPS function here.
Current PIN - The current value of the Router's PIN is displayed here. The default PIN of the
Router can be found in the label or User Guide.
Restore PIN - Restore the PIN of the Router to its default.
Gen New PIN - Click this button, and then you can get a new random value for the Router's
PIN. You can ensure the network security by generating a new PIN.
Add device - You can add a new device to the existing network manually by clicking this
button.
b). To add a new device:
If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless
connection between wireless adapter and Router using either Push Button Configuration (PBC)
method or PIN method.
Note:
To build a successful connection by WPS, you should also do the corresponding configuration of
the new device for WPS function meanwhile.
I. Use the Wi-Fi Protected Setup Button
Use this method if your client device has a Wi-Fi Protected Setup button.
Step 1: Press the WPS button on the back panel of the Router.
-17-
TL-WR720N 150Mbps Wireless N Router
You can also keep the default WPS Status as Enabled and click the Add device button
in Figure 4-2, then Choose “Press the button of t
he new device in two minutes” and
click Connect. (Shown in the following figure)
Figure 4-3 Add A New Device
Step 2: Press and hold the WPS button of the client device directly.
Step 3: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected
Setup process.
Step 4: When the WPS LED is on, the client device has successfully connected to the Router.
Step 5: Refer back to your client device or its documentation for further instructions.
II. Enter the client device’s PIN on the Router
Use this method if your client device has a Wi-Fi Protected Setup PIN number.
Step 1: Keep the default WPS Status as Enabled and click the Add device button in Figure 4-2,
then the following screen will appear.
Figure 4-4 Add A New Device
Step 2: Enter the PIN number from the client device in the field on the above WPS screen. Then
click Connect button.
Step 3: “Connect successfully” will appear on the screen of Figure 4-4, which means the client
r
device has successfully connected to the Route
.
III. Enter the Router’s PIN on your client device
Use this method if your client device asks for the Router’s PIN number.
Step 1: On the client device, enter the PIN number listed on the Router’s Wi-Fi Protected Setup
screen. (It is also labeled on the bottom of the Router.)
Step 2: The Wi-Fi Protected Setup LED flashes for two minutes during the Wi-Fi Protected
Setup process.
-18-
TL-WR720N 150Mbps Wireless N Router
Step 3: When the WPS LED is on, the client device has successfully connected to the Router.
Step 4: Refer back to your client device or its documentation for further instructions.
Note:
1) The WPS LED on the Router will light green for five minutes if the device has been
2) The WPS function cannot be configured if the Wireless Function of the Router is disabled.
successfully added to the network.
Please make sure the Wireless Function is enabled before configuring the WPS.
4.5 Network
Figure 4-5 the Network menu
There are three submenus under the Network menu (shown in Figure 4-5): LAN, WAN and MAC
Clone. Click any of them, and you will be able to configure the corresponding function.
-19-
TL-WR720N 150Mbps Wireless N Router
4.5.1 WAN
Choose menu “Network→WAN”, and then you can configure the IP parameters of the WAN on
the screen below.
1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will
automatically get IP parameters from your ISP. You can see the page as follows (Figure
4-6):
Figure 4-6 WAN - Dynamic IP
This page displays the WAN IP parameters assigned dynamically by your ISP, including IP
address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP
parameters from your ISP. Click the Release button to release the IP parameters.
MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks
is 1500 Bytes. It is not recommended that you change the default MTU Size unless required
by your ISP.
Use These DNS Servers - If your ISP gives you one or two DNS addresses, select Use
These DNS Servers and enter the primary and secondary addresses into the correct fields.
Otherwise, the DNS servers will be assigned dynamically from your ISP.
Note:
If you find error when you go to a Web site after entering the DNS addresses, it is likely that your
DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.
-20-
TL-WR720N 150Mbps Wireless N Router
Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast
applications. If you cannot get the IP Address normally, you can choose this option. (It is
rarely required.)
2. If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway and DNS setting,
select Static IP. The Static IP settings page will appear as shown in Figure 4-7.
Figure 4-7 WAN - Static IP
IP Address - Enter the IP address in dotted-decimal notation provided by your ISP.
Subnet Mask - Enter the subnet Mask provided by your ISP in dotted-decimal notation.
Usually, the Sub Mask is 255.255.255.0.
Default Gateway - Enter the gateway IP address provided by your ISP in dotted-decimal
notation.
MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks
is 1500 Bytes. It is not recommended that you change the default MTU Size unless required
by your ISP.
Primary/Secondary DNS - Enter one or two DNS addresses in dotted-decimal notation
provided by your ISP.
-21-
Loading...