TP Link WR54XG Users Manual

Specifications are subject to change without notice. trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are

trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to

make any derivative such as translation, transformation, or adaptation without

is a registered

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

¾ Reorient or relocate the receiving antenna.

¾ Increase the separation between the equipment and receiver.

¾ Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

¾ Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may

cause undesired operation

Changes or modifications to this unit not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This device and its antenna must not be co-located or

operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, the antenna used for this

transmitter must be installed to provide a separation distance of at least 20 cm from all

persons and must not be co-located or operating in conjunction with any other antenna

or transmitter”.

CE Declaration of Conformity

For the following equipment: TL-WR541G

Is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

(89/336/EEC), Low-voltage Directive (73/23/EEC) and the Amendment Directive (93/68/EEC),

the procedures given in European Council Directive 99/5/EC and 89/3360EEC.

The equipment was passed. The test was performed according to the following

European standards:

¾ EN 300 328 V.1.4.1 (2003)

¾ EN 301 489-1 V.1.4.1 (2002) / EN 301 489-17 V.1.2.1 (2002) ¾ EN 60950-1: 2001 ¾ EN 55022: 1998 + A1: 2000 + A2: 2003 ¾ EN61000-3-2:2001 ¾ EN61000-3-3:2001

¾ EN 55024: 1998 +A1: 2001 + A2: 2003

European standards dictate maximum radiated transmit power of 100mW EIRP and

frequency range 2.400-2.4835GHz; In France, the equipment must be restricted to the

2.4465-2.4835GHz frequency range and must be restricted to indoor use.

Package contents.............................................................................................................. 1

Chapter 1: About this Guide.............................................................................................. 2

1.1 Purposes.............................................................................................................. 2

1.2 Conventions ......................................................................................................... 2

1.3 Overview of this User Guide ................................................................................ 2

Chapter 2: Introduction...................................................................................................... 3

2.1 Overview of the Router ........................................................................................ 3

2.2 Features............................................................................................................... 3

2.3 Panel Layout ........................................................................................................ 4

2.3.1 The Front Panel ......................................................................................... 4

2.3.2 The Rear Panel.......................................................................................... 4

Chapter 3: Connecting the Router..................................................................................... 6

3.1 System Requirements.......................................................................................... 6

3.2 Installation Environment Requirements................................................................ 6

3.3 Connecting the Router ......................................................................................... 6

Chapter 4: Quick Installation Guide................................................................................... 8

4.1 TCP/IP configuration ............................................................................................ 8

4.2 Quick Installation Guide ....................................................................................... 9

Chapter 5: Configuring the Router .................................................................................. 13

5.1 login ................................................................................................................... 13

5.2 Status................................................................................................................. 13

5.3 Quick Setup ....................................................................................................... 14

5.4 Network.............................................................................................................. 14

5.4.1 LAN.......................................................................................................... 15

5.4.2 WAN......................................................................................................... 15

5.4.3 MAC Clone .............................................................................................. 19

5.5 Wireless ............................................................................................................. 20

5.5.1 Wireless Settings ..................................................................................... 20

5.5.2 MAC Filtering ........................................................................................... 23

5.5.3 Wireless Statistics.................................................................................... 25

5.6 DHCP................................................................................................................. 26

5.6.1 DHCP Settings......................................................................................... 26

5.6.2 DHCP Clients List .................................................................................... 27

5.6.3 Address Reservation................................................................................ 28

5.7 Forwarding ......................................................................................................... 29

5.7.1 Virtual Servers ......................................................................................... 29

5.7.2 Port Triggering ......................................................................................... 31

5.7.3 DMZ ......................................................................................................... 33

5.7.4 UPnP ....................................................................................................... 33

5.8 Security .............................................................................................................. 34

5.8.1 Firewall .................................................................................................... 34

5.8.2 IP Address Filtering.................................................................................. 35

5.8.3 Domain Filtering....................................................................................... 37

5.8.4 MAC Filtering ........................................................................................... 38

5.8.5 Remote Management .............................................................................. 40

5.8.6 Advanced Security ................................................................................... 41

5.9 Static Routing..................................................................................................... 42

5.10 DDNS............................................................................................................... 43

5.10.1 Oray.net DDNS ...................................................................................... 44

5.10.2 Comexe.cn DDNS.................................................................................. 44

5.11 System Tools .................................................................................................... 45

5.11.1 Firmware ................................................................................................ 46

5.11.2 Factory Defaults ..................................................................................... 46

5.11.3 Reboot ................................................................................................... 47

5.11.4 Password ............................................................................................... 47

5.11.5 Log ......................................................................................................... 48

5.11.6 Statistics................................................................................................. 48

Appendix A: FAQ............................................................................................................. 50

Appendix B: Configuring the PCs.................................................................................... 54

Appendix C: Specifications.............................................................................................. 59

Appendix D: Glossary ..................................................................................................... 60

Appendix E: Contact Information..................................................................................... 62

TL-WR541G 54M Wireless Router User Guide

Package contents

The following contents should be found in your box:

¾ One TL-WR541G 54Mbps Wireless Router

¾ One AC power Adapter for TL-WR541G 54Mbps Wireless Router

¾ Quick Installation Guide

¾ One Resource CD for TL-WR541G 54Mbps Wireless Router, including:

• This Guide

• Other Helpful Information

¾ Wall-mounting screws

Note: If any of the listed contents are damaged or missing, please contact the retailer

from whom you purchased the TL-WR541G 54Mbps Wireless Router for assistance.

格式化: 項目符號及編號

- 1 -

TL-WR541G 54M Wireless Router User Guide

Chapter 1: About this Guide

Thank you for choosing the TL-WR541G 54Mbps Wireless Router. This router provides

dedicated solution for Small Office/Home Office (SOHO) networks. With your network all

connected, your local wired or wireless network can share Internet access, files and fun

for multiple PCs through one ISP account.

It adopts 2x to 3x eXtended Range

transmission distance is 2-3 times of traditional IEEE 802.11g/b solutions, up to 855.36m

tested in China. Transmission range is extended to 4-9 times.

It is an easy, web-based setup for installation and management. Even though you may

not be familiar with the router, this guide will make configuring the router easy. Before

installing the router, please look through this guide to get to know all the router’s

functions.

1.1 Purposes

This Guide tells you how to use the TL-WR541G 54Mbps Wireless Router.

1.2 Conventions

WLAN transmission technology so that

The router mentioned in this guide stands for TL-WR541G 54Mbps Wireless Router.

1.3 Overview of this User Guide

Chapter 1: About this Guide

Chapter 2: Introduction

Chapter 3: Connecting the Router

Chapter 4: Quick Installation Guide

Chapter 5: Configuring the Router

Appendix A: FAQ

Appendix B: Configuring the PCs

Appendix C: Specifications

Appendix D: Glossary

Appendix E: Contact Information

- 2 -

TL-WR541G 54M Wireless Router User Guide

Chapter 2: Introduction

2.1 Overview of the Router

The TL-WR541G 54Mbps Wireless Router integrates 4-port Switch, firewall, NAT-router

and Wireless AP. Its design is dedicated to Small Office/Home Office (SOHO) wireless

network solutions. The TL-WR541G 54Mbps Wireless Router will allow you to connect

your network wirelessly better than ever, sharing Internet Access, files and fun, easily

and securely.

In the most attentive wireless security, the TL-WR541G 54Mbps Wireless Router

provides multiple protection measures. It can be set to turn off wireless network name

(SSID) broadcast so that only stations that have the SSID can be connected. The router

provides wireless LAN 64/128/152-bit WEP encryption security, and WPA and WPA-PSK

authentication, as well as TKIP/AES encryption security. It also supports VPN

pass-through for sensitive data secure transmission.

The TL-WR541G 54Mbps Wireless Router complies with the IEEE 802.11g/b standards

so that the data transmission rate is up to 54Mbps. It adopts 2x to 3x eXtended

Range

traditional IEEE 802.11g/b solutions, up to a distance of 855.36m tested in China.

Transmission range is extended to 4-9 times. It is compatible with all IEEE 802.11b

products.

WLAN transmission technology so that transmission distance is 2-3 times of

The TL-WR541G 54Mbps Wireless Router has built-in NAT and DHCP server supporting

static IP address distributing. It also supports Virtual Server and DMZ host for Port

Triggering needs, and remote management and log so that network administrators can

manage and monitor the network on real time.

The TL-WR541G 54Mbps Wireless Router is easy-to-manage. Quick Setup is supported

and friendly help messages are provided for every step. So you can configure it quickly

and share Internet access, files and fun.

2.2 Features

¾ Complies with IEEE802.11g, IEEE802.11b, IEEE802.3, IEEE802.3u standards

¾ Built in 4-port 10/100Mbps Switch

¾ Ethernet connection to a WAN device, such as a cable modem or DSL modem

¾ Adopts 2x to 3x eXtended Range

¾ Shares data and Internet access for the network, connecting Internet through

PPPoE on demand and disconnecting when idle

¾ Supports 54/48/36/24/18/12/9/6/11/5.5/3/2/1Mbps wireless LAN data transfer rates

¾ Provides 64/128/152-bit WEP encryption security

¾ Provides WPA and WPA-PSK authentication and TKIP/AES encryption security

¾ Provides wireless LAN ACL (Access Control List)

¾ Built-in NAT and DHCP server supporting static IP address distributing

¾ Supports Virtual Server, Port Triggering, and DMZ host

WLAN transmission technology

- 3 -

TL-WR541G 54M Wireless Router User Guide

¾ Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC

address filtering

¾ Supports TCP/IP, PPPoE, DHCP, ICMP, NAT

¾ Supports UPnP, Dynamic DNS, Static Routing, VPN pass-through

¾ Supports Traffic Stat.

¾ Supports ICMP-FLOOD, UDP-FLOOD, TCP-SYN-FLOOD filter

¾ Ignores Ping packets from WAN or LAN ports

¾ Supports firmware upgrade

¾ Supports Remote and Web management

2.3 Panel Layout

2.3.1 The Front Panel

The front panel of the TL-WR541G consists of several LED indicators, which is designed

to indicate connections. Viewed from left to right. Table 2-1 describes the LEDs on the

front panel of the router.

刪除:

Figure 2-1: Front Panel sketch

Name Action Description

Power

System

Not lit No Power

Lit up Power on

Lit up

The router is initialising

Flashing The router is working properly

Not lit The router has a hardware error

There is no device linked to the corresponding port

There is a device linked to the corresponding port but

no activity

There is an active device linked to the corresponding

port

Link/Act

WLAN

Not lit

Lit up

Flashing

Not lit The Wireless Radio function is disabled

Flashing The Wireless Radio function is enabled

The LEDs description

2.3.2 The Rear Panel

The rear panel contains the following features. (Viewed from left to right:)

¾ Wireless antenna

¾ Factory Default Reset button

There are two ways to reset the router's factory defaults:

1) Use the Factory Defa ults function on System Tools -> Factory Defaults page in the

- 4 -

TL-WR541G 54M Wireless Router User Guide

router's Web-based Utility.

2) Use the Factory Default Reset button: First, turn off the router's power. Second, press and

hold the default reset button then turn on the router's power, until the system LED lights up

(about 3 seconds). Last, release the reset button and wait for the router to reboot.

Note: Ensure the router is powered on before it restarts completely.

¾ WAN RJ45 port for connecting the router to a cable, DSL modem or Ethernet

¾ Four LAN 10/100Mbps RJ45 ports for connecting the router to the local PCs

¾ AC power socket: only use the power adapter supplied with the TL-WR541G

54Mbps Wireless Router, use of a different adapter may result in product damage.

RESET

1WAN 2 3 4

Figure 2-2 Rear Panel sketch

- 5 -

TL-WR541G 54M Wireless Router User Guide

Chapter 3: Connecting the Router

3.1 System Requirements

¾ Broadband Internet Access Service (DSL/Cable/Ethernet)

¾ One DSL/Cable modem that has an RJ45 connector (you do not need it if you

connect the router to Ethernet)

¾ Each PC on the LAN needs a working Ethernet Adapter and an Ethernet cable with

RJ45 connectors

¾ TCP/IP protocol must be installed on each PC

¾ Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator

6.0 or later

3.2 Installation Environment Requirements

¾ Not in direct sunlight or near a heater or heating vent

¾ Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on

all sides of the router

¾ Well ventilated (especially if it is in a closet) ¾ Operating temperature: 0℃~40℃ (32℉~104℉)

¾ Operating Humidity: 10%~90%RH, Non-condensing

3.3 Connecting the Router

Before you install the router, you should connect your PC to the Internet through your

broadband service successfully. If there is any problem, please contact your ISP. After

that, please install the router according to the following steps. Don't forget to pull out the

power plug and keep your hands dry.

1. Power off your PC(s), Cable/DSL modem, and the router.

2. Locate an optimum location for the router. The best place is usually near the center

of the area in which your PC(s) will wirelessly connect. The place must accord with

the Installation Environment Requirements

3. Adjust the direction of the antenna. Normally, upright is a good direction.

4. Connect the PC(s) and each Switch/Hub on your LAN to the LAN Ports on the router,

shown in figure 3-1.

5. Connect the DSL/Cable Modem to the WAN port on the router, shown in figure 3-1.

6. Connect the AC power adapter to the AC power socket on the router, and the other

end into an electrical outlet. The router will start to work automatically.

7. Power on your PC(s) and Cable/DSL modem.

- 6 -

TL-WR541G 54M Wireless Router User Guide

RESET

To WAN

（）

XDSL Cable Et hernet

、、

4321WAN

To LAN

Switch/Hub

Figure 3-1 Hardware Installation of the TL-WR541G 54Mbps Wireless Router

- 7 -

TL-WR541G 54M Wireless Router User Guide

Chapter 4: Quick Installation Guide

After connecting the TL-WR541G Router into your network, you should configure it. This

chapter describes how to configure the basic functions of your TL-WR541G Wireless

Router. These procedures only take you a few minutes. You can access the Internet via

the router immediately after successfully configured.

4.1 TCP/IP configuration

The default IP address of the TL-WR541G 54Mbps Wireless Router is 192.168.1.1, and

the default Subnet Mask is 255.255.255.0. These values can be seen from the LAN.

They can be changed as you desire, as an example we use the default values for

description in this guide.

Connect the local PCs to the LAN ports on the router. There are then two means to

configure the IP address for your PCs.

¾ Configure the IP address manually

1) Set up the TCP/IP Protocol for your PC(s). If you need instructions as to how to

do this, please refer to Appendix B: "Configuring the PCs."

2) Configure the network parameters. The IP address is 192.168.1.xxx ("xxx" is

from 2 to 254), Subnet Mask is 255.255.255.0, and Gateway is 192.168.1.1

(The router's default IP address)

¾ Obtain an IP address automatically

1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on

your PC(s). If you need instructions as to how to do this, please refer to

Appendix B: "Configuring the PCs."

2) Power off the router and PC(s). Then turn on the router, and restart the PC(s).

The built-in DHCP server will assign IP addresses for the PC(s).

Now, you can run the Ping command in the command prompt to verify the network

connection between your PC(s) and the router. The following example is in Windows

2000 OS.

Open a command prompt, and type ping 192.168.1.1, then press Enter.

Figure 4-1 Successful result of Ping command

If the result displayed is similar to that shown in figure 4-1, the connection between your

- 8 -

TL-WR541G 54M Wireless Router User Guide

PC and the router has been established.

Figure 4-2 Failed result of Ping command

If the result displayed is similar to that shown in figure 4-2, it means that your PC has not

connected to the router. Please check it following these steps:

1. Is the connection between your PC and the router correct?

Note: The Link/Act LEDs of LAN port on the router and LEDs on your PC's adapter

should be lit.

2. Is the TCP/IP configuration for your PC correct?

Note: If the router's IP address is 192.168.1.1, your PC's IP address must be within

the range of 192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1

4.2 Quick Installation Guide

With a Web-based (Internet Explorer or Netscape® Navigator) utility, the TL-WR541G

54Mbps Wireless Router is easy to configure and manage. The Web-based utility can be

used on any Windows, Macintosh or UNIX OS with a web browser.

Connect to the router by typing http://192.168.1.1 in the address field of web browser.

Figure 4-3 Login to the router

After a moment, a login window will appear similar to that shown in Figure 4-4. Enter

admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.

Figure 4-4 Login Windows

- 9 -

TL-WR541G 54M Wireless Router User Guide

Note: If the above screen does not prompt, it means that your web-browser has been set

to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen

that appears, cancel the Using Proxy checkbox, and click OK to finish it.

If the User Name and Password are correct, you can configure the router using the web

browser. Please click the Quick Setup link on the left of the main menu and the Quick

Setup screen will appear.

Figure 4-5 Quick Setup

Click Next, the Choose WAN Connection Type page will appear, shown in figure 4-6.

Figure 4-6 Choose WAN Connection Type

The router supports three popular ways to connect to Internet. Please select one

compatible with your ISP. Click Next to enter the necessary network parameters. If you choose "PPPoE", you will see this page shown in figure 4-7:

Figure 4-7 Quick Setup - PPPoE

¾ User Name and Password - Enter the User Name and Password provided by your

ISP. These fields are case sensitive. If you have difficulty with this process, please

- 10 -

TL-WR541G 54M Wireless Router User Guide

contact your ISP.

If you choose "Dynamic IP", the router will automatically receive the IP parameters from

your ISP without needing to enter any parameters.

If you Choose "Static IP", the Static IP settings page will appear, shown in figure 4-8:

Figure 4-8 Quick Setup - Static IP

Note: The IP parameters should have been provided by your ISP.

¾ IP Address - This is the WAN IP address as seen by external users on the Internet

(including your ISP). Enter the IP address into the field.

¾ Subnet Mask - The Subnet Mask is used for the WAN IP address, it is usually

255.255.255.0

¾ Default Gateway - Enter the gateway into the box if required. ¾ Primary DNS - Enter the DNS Server IP address into the boxes if required. ¾ Secondary DNS - If your ISP provides another DNS server, enter it into this field.

After you complete the above, click Next, the Wireless settings page will appear, shown

in figure 4-9.

Figure 4-9 Quick Setup - Wireless settings

In this page, you can configure the following wireless parameters:

¾ Wireless Radio - indicates whether the Access Point feature of the router is

enabled or disabled. If disabled, the WLAN LED on the front panel will not be lit and

the wireless stations will not be able to access the router. If enabled, the WLAN

LED will be lit up and wireless stations will be able to access the router.

¾ SSID - Enter a value of up to 32 characters. The same SSID must be assigned to

- 11 -

TL-WR541G 54M Wireless Router User Guide

all wireless devices on your network. The default SSID is TP-LINK. This value is

case-sensitive. For example, TP-LINK is NOT the same as TP-Link.

¾ Channel - the current channel in use. This field determines which operating

frequency will be used.

¾ Mode - Indicates the current mode (54Mbps (802.11g), 11Mbps (802.11b)). If you

select 54Mbps (802.11g), it is compatible with 11Mbps (802.11b).

These settings are only for basic wireless parameters, for advanced settings, please

refer to Section 5.5: "Wireless."

Note: The change of wireless settings won't take effect until the router reboots! You can

reboot it manually. If you need instructions as to how to do this, please refer to Section

5.11.3: "Rebooting the Router"

Click the Next button, you will then see the Finish page:

Figure 4-10 Quick Setup - Finish

After finishing all configurations of basic network parameters, please click Finish button to exit this Quick Setup.

- 12 -

TL-WR541G 54M Wireless Router User Guide

Chapter 5: Configuring the Router

This chapter describes each web page's key functions.

5.1 login

After your successful login, you can configure and manage the router. There are ten main

menus on the left of the web-based utility. Submenus will be available after you click one

of the main menus. The ten main menus are: Status, Quick Setup, Network, Wireless, DHCP, Forwarding, Security, Static Routing, DDNS and System Tools. On the right of

the web-based utility, there are the detailed explanations and instructions for the

corresponding page. To apply any settings you have altered on the page, please click the

Save button.

There are the detailed explanations for each web page's key functions below.

5.2 Status

The Status page displays the router's current status and configuration. All information is

read-only.

1. LAN

This field displays the current settings or information for the LAN, including the MAC address, IP address and Subnet Mask.

2. Wireless

This field displays basic information or status for wireless function, including Wireless Radio, SSID, Channel, Mode, Wireless MAC address and IP address.

3. WAN

These parameters apply to the WAN port of the router, including MAC address, IP address, Subnet Mask, Default Gateway, DNS server and WAN connection type.

If PPPoE is chosen as the WAN connection type, the Disconnect button will be

shown here while you are accessing the Internet. You can also cut the connection by

clicking the button. If you have not connected to the Internet, a Connect button will be

shown, you can then establish the connection by clicking the button.

4. Traffic Statistics

This field displays the router's traffic statistics.

5. System Up Time

The time of the router running from it's powered on or reset.

- 13 -

TL-WR541G 54M Wireless Router User Guide

Figure 5-1 Router Status

5.3 Quick Setup

Please refer to Section 4.2: "Quick Installation Guide."

5.4 Network

Figure 5-2 the Network menu

There are three submenus under the Network menu (shown in figure 5-2): LAN, WAN and MAC Clone. Click any of them, and you will be able to configure the corresponding

function. The detailed explanations for each submenu are provided below.

- 14 -

TL-WR541G 54M Wireless Router User Guide

5.4.1 LAN

You can configure the IP parameters of LAN on this page.

Figure 5-3 LAN

¾ MAC Address - the physical address of the router, as seen from the LAN. The

value can't be changed.

¾ IP Address - Enter the IP address of your router in dotted-decimal notation (factory

default: 192.168.1.1).

¾ Subnet Mask - An address code that determines the size of the network. Normally

use 255.255.255.0 as the subnet mask.

Note:

a. If you change the IP Address of LAN, you must use the new IP Address to login the

router.

b. If the new LAN IP Address you set is not in the same subnet, the IP Address pool in

the DHCP sever will not take effect, until they are re-configured.

c. If the new LAN IP Address you set is not in the same subnet, the Virtual Server and

DMZ Host will change accordingly at the same time.

5.4.2 WAN

You can configure the WAN port parameters on this page.

First, please choose the WAN Connection Type (Dynamic/Static IP/PPPoE) to the

Internet. The default type is PPPoE. If you aren’t given any login parameters (fixed IP Address, logging ID, etc), please select Dynamic IP. If you are given a fixed IP (static IP), please select Static IP. If you are given a user name and a password, please select

. If you are not sure which connection type you use currently, please contact

PPPoE

your ISP to obtain the correct information.

1. If you choose Dynamic IP, the router will automatically get IP parameters from

your ISP. You can see the page as follows (figure 5-4):

- 15 -

+ 47 hidden pages