TP Link WDR3600 User Manual
TL-WDR3600
N600 Wireless Dual Band Gigabit Router
Rev: 1.0.0
1910010674
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reason/remark
Bulgaria None
Italy None
Luxembourg None
Norway Implemented
General authorization required for outdoor use and
public service
If used outside of own premises, general authorization is
required
General authorization required for network and service
supply(not for spectrum)
This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
For operation within 5.15-5.25GHz frequency range, it is restricted to indoor environment.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 3dBi. Antennas not included in this list or having a gain greater than 3dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
Industry Canada Statement:
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potentialradio interference to other users, the antenna type and its gain should be so
chosen that theequivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:
(1) Le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) Ce dispositif doit accepter tout brouillage reçu,y compris un brouillage susceptible de
provoquer un fonctionnement indésirable.
NOTE IMPORTANTE:
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
Korea Warning Statements:
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice:
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功
率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並
改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電
機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: N600 Wireless Dual Band Gigabit Router
Model No.: TL-WDR3600
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
ETSI EN 300 328 V1.7.1: 2006
ETSI EN 301 489-1 V1.8.1:2008& ETSI EN 301 489-17 V2.1.1:2009
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN60950-1:2006+A11:2009+A1:2010+A12:2011
EN62311:2008
EN 301 893
EN 302 502
The product carries the CE Mark:
Person is responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2012
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
CONTENTS
Package Contents.....................................................................................................1
Chapter 1. Introduction......................................................................................... 2
1.1 Overview of the Router............................................................................................... 2
1.2 Conventions ...............................................................................................................3
1.3 Main Features ............................................................................................................3
1.4 Panel Layout .............................................................................................................. 4
1.4.1 The Front Panel.............................................................................................. 4
1.4.2 The Rear Panel .............................................................................................. 5
Chapter 2. Connecting the Router .......................................................................7
2.1 System Requirements ................................................................................................7
2.2 Installation Environment Requirements...................................................................... 7
2.3 Connecting the Router ...............................................................................................7
Chapter 3. Quick Installation Guide..................................................................... 9
3.1 TCP/IP Configuration .................................................................................................9
3.2 Quick Installation Guide ...........................................................................................10
Chapter 4. Configuring the Router ....................................................................19
4.1 Login ........................................................................................................................19
4.2 Status .......................................................................................................................19
4.3 Quick Setup.............................................................................................................. 21
4.4 Network .................................................................................................................... 21
4.4.1 WAN .............................................................................................................21
4.4.2 LAN .............................................................................................................. 30
4.4.3 MAC Clone ...................................................................................................31
4.5 Dual Band Selection................................................................................................. 32
4.6 Wireless 2.4GHz ......................................................................................................33
4.6.1 Wireless Settings.......................................................................................... 33
4.6.2 WPS .............................................................................................................35
4.6.3 Wireless Security.......................................................................................... 38
4.6.4 Wireless MAC Filtering ................................................................................. 41
4.6.5 Wireless Advanced .......................................................................................43
4.6.6 Wireless Statistics.........................................................................................45
4.7 Wireless 5GHz ......................................................................................................... 45
- I -
4.7.1 Wireless Settings.......................................................................................... 46
4.7.2 WPS .............................................................................................................48
4.7.3 Wireless Security.......................................................................................... 50
4.7.4 Wireless MAC Filtering ................................................................................. 53
4.7.5 Wireless Advanced .......................................................................................55
4.7.6 Wireless Statistics.........................................................................................57
4.8 DHCP ....................................................................................................................... 57
4.8.1 DHCP Settings ............................................................................................. 58
4.8.2 DHCP Clients List ......................................................................................... 59
4.8.3 Address Reservation ....................................................................................59
4.9 USB Settings............................................................................................................ 60
4.9.1 Storage Sharing............................................................................................ 61
4.9.2 FTP Server ................................................................................................... 62
4.9.3 Media Server ................................................................................................64
4.9.4 Print Server................................................................................................... 66
4.9.5 User Accounts .............................................................................................. 67
4.10 NAT ..........................................................................................................................69
4.11 Forwarding ............................................................................................................... 69
4.11.1 Virtual Servers ..............................................................................................69
4.11.2 Port Triggering .............................................................................................. 71
4.11.3 DMZ.............................................................................................................. 73
4.11.4 UPnP ............................................................................................................74
4.12 Security .................................................................................................................... 75
4.12.1 Basic Security............................................................................................... 75
4.12.2 Advanced Security........................................................................................ 77
4.12.3 Local Management ....................................................................................... 78
4.12.4 Remote Management ................................................................................... 79
4.13 Parental Control ....................................................................................................... 80
4.14 Access Control......................................................................................................... 83
4.14.1 Rule .............................................................................................................. 83
4.14.2 Host .............................................................................................................. 89
4.14.3 Target............................................................................................................ 90
4.14.4 Schedule....................................................................................................... 92
4.15 Advanced Routing.................................................................................................... 94
4.15.1 Static Routing List......................................................................................... 95
4.15.2 System Routing Table................................................................................... 96
- II -
4.16 Bandwidth Control.................................................................................................... 96
4.16.1 Control Settings ............................................................................................ 97
4.16.2 Rules List...................................................................................................... 97
4.17 IP & MAC Binding Setting ........................................................................................98
4.17.1 Binding Settings............................................................................................ 98
4.17.2 ARP List......................................................................................................100
4.18 Dynamic DNS......................................................................................................... 101
4.18.1 Comexe.cn DDNS ...................................................................................... 101
4.18.2 Dyndns.org DDNS ...................................................................................... 102
4.18.3 No-ip.com DDNS ........................................................................................ 103
4.19 System Tools.......................................................................................................... 104
4.19.1 Time Setting................................................................................................ 104
4.19.2 Diagnostic................................................................................................... 106
4.19.3 Firmware Upgrade...................................................................................... 107
4.19.4 Factory Defaults .........................................................................................108
4.19.5 Backup & Restore....................................................................................... 109
4.19.6 Reboot........................................................................................................ 110
4.19.7 Password.................................................................................................... 110
4.19.8 System Log..................................................................................................111
4.19.9 Statistics ..................................................................................................... 113
Appendix A: FAQ .................................................................................................. 115
Appendix B: Configuring the PCs....................................................................... 120
Appendix C: Specifications .................................................................................123
Appendix D: Glossary .......................................................................................... 124
- III -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Package Contents
The following items should be found in your package:
¾ TL-WDR3600 N600 Wireless Dual Band Gigabit Router
¾ DC Power Adapter for TL-WDR3600 N600 Wireless Dual Band Gigabit Router
¾ Quick Installation Guide
¾ Resource CD for TL-WDR3600 N600 Wireless Dual Band Gigabit Router, including:
• This Guide
• Other Helpful Information
Note:
)
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.
- 1 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Chapter 1. Introduction
Thank you for choosing the TL-WDR3600 N600 Wireless Dual Band Gigabit Router.
1.1 Overview of the Router
The TL-WDR3600 N600 Wireless Dual Band Gigabit Router integrates 4-port Switch, Firewall,
NAT-Router and Wireless AP. Powered by 3x3 MIMO technology, the N600 Wireless Dual Band
Gigabit Router delivers exceptional range and speed, which can fully meet the need of Small
Office/Home Office (SOHO) networks and the users demanding higher networking performance.
Your wireless connections are radio band selectable to avoid interference in your area, and the four
built-in Gigabit ports supply high-speed connection to your wired devices.
The TL-WDR3600 N600 Wireless Dual Band Gigabit Router provides up to 300Mbps (2.4GHz) +
300Mbps (5GHz) wireless connection with other 802.11n wireless clients. The incredible speed makes
it ideal for handling multiple data streams at the same time, which ensures your network stable and
smooth. The performance of this 802.11n wireless Router will give you the unexpected networking
experience at speed much faster than 802.11g. It is also compatible with all IEEE 802.11g and IEEE
802.11b products.
Multiple Security Protections
With multiple protection measures, including SSID broadcast control and wireless LAN
64/128/152-bit WEP encryption, Wi-Fi Protected Access (WPA2- PSK, WPA- PSK), as well as
advanced Firewall protections, the TL-WDR3600 N600 Wireless Dual Band Gigabit Router
provides complete data privacy.
The TL-WDR3600 N600 Wireless Dual Band Gigabit Router provides flexible access control, so
that parents or network administrators can establish restricted access policies for children or staff. It
also supports Virtual Server and DMZ host for Port Triggering, and then the network administrators
can manage and monitor the network in real time with the remote management function.
Incredible Speed
Flexible Access Control
Simple Installation
Since the Router is compatible with virtually all the major operating systems, it is very easy to
manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in
this user guide. Before installing the Router, please look through this guide to know all the
Router’s functions.
- 2 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
1.2 Conventions
The Router or TL-WDR3600 mentioned in this guide stands for TL-WDR3600 N600 Wireless Dual
Band Gigabit Router without any explanation.
1.3 Main Features
¾ Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps (2.4GHz) +
300Mbps (5GHz).
¾ One 10/100/1000M Auto-Negotiation RJ45 Internet port, four 10/100/1000M Auto-Negotiation
RJ45 Ethernet ports, supporting Auto MDI/MDIX.
¾ Provides USB ports supporting storage/FTP/Media/Print Server.
¾ Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.
¾ Shares data and Internet access for users, supporting Dynamic IP/Static IP/PPPoE Internet
access.
¾ Works in 2.4GHz or 5GHz radio bands, doubling your network capability.
¾ Supports Virtual Server, Special Application and DMZ host.
¾ Supports UPnP, Dynamic DNS, Static Routing.
¾ Provides Automatic-connection and Scheduled Connection on certain time to the Internet.
¾ Built-in NAT and DHCP server supporting static IP address distributing.
¾ Supports Parental Control and Access Control.
¾ Connects Internet on demand and disconnects from the Internet when idle for PPPoE.
¾ Provides 64/128/152-bit WEP encryption security and wireless LAN ACL (Access Control
List).
¾ Supports Flow Statistics.
¾ Supports firmware upgrade and Web management.
- 3 -
1.4 Panel Layout
1.4.1 The Front Panel
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Figure 1-1 LEDs on the front panel
The Router’s LEDs are located on the front panel (View from left to right).
Name Status Indication
Off Power is off.
(Power)
On Power is on.
On The Router is initializing or maybe has a system error.
(System)
(Wireless
2.4GHz)
(Wireless
5GHz)
Flashing The Router is working properly.
Off The Router has a system error.
Off The wireless function is disabled.
Flashing
Off The wireless function is disabled.
Flashing
Off There is no device linked to the corresponding port.
The wireless function is enabled. The Router is working on
2.4GHz radio band.
The wireless function is enabled. The Router is working on
5GHz radio band.
(Ethernet)
(Internet)
On
Flashing There is an active device linked to the corresponding port.
There is a device linked to the corresponding port but there
is no activity.
- 4 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Slow
Flash
(WPS)
(USB on the
rear panel)
Note:
)
1) After a device is successfully added to the network by WPS function, the WPS LED will keep
on for about 5 minutes and then turn off.
2) The Router is set to working concurrently in 2.4GHz and 5GHz by default. If you desire to
choose the working frequency, please go to 4.5 Dual Band Selection
On
Quick
Flash
Off No storage device or printer is plugged into the USB port.
On A storage device or printer has connected to the USB port.
A wireless device is connecting to the network by WPS
function. This process will last in the first 2 minutes.
A wireless device has been successfully added to the
network by WPS function.
A wireless device failed to be added to the network by WPS
function.
Table 1-1 The LEDs Description
.
1.4.2 The Rear Panel
Figure 1-2 Rear Panel sketch
The following parts are located on the rear panel (View from left to right).
¾ Power: The Power socket is where you will connect the power adapter. Please use the
power adapter provided with this TL-WDR3600 N600 Wireless Dual Band Gigabit Router.
¾ On/Off: The switch for the power.
¾ Wireless On/Off: The switch for the wireless function.
¾ USB: The USB port connects to a USB storage device or a USB printer.
¾ Internet: This port is where you will connect the DSL/cable Modem, or Ethernet.
¾ Ethernet (1, 2, 3, 4): These ports (1, 2, 3, 4) connect the Router to the local PC(s).
- 5 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
¾ WPS/Reset:
Pressing this button for less than 5 seconds enables the WPS function. If your client devices,
such as wireless adapters, that support Wi-Fi Protected Setup, then you can press this
button to quickly establish a connection between the Router and client devices and
automatically configure wireless security for your wireless network.
Pressing this button for more than 5 seconds enables the Reset function. With the Router
powered on, press and hold the WPS/Reset button (approximately 8 seconds) until the SYS
LED becomes quick-flash from slow-flash. And then release the button and wait the Router
to reboot to its factory default settings.
¾ Wireless antenna: To receive and transmit the wireless data.
- 6 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Chapter 2. Connecting the Router
2.1 System Requirements
¾ Broadband Internet Access Service (DSL/Cable/Ethernet)
¾ One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is
connected directly to the Ethernet)
¾ PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors
¾ TCP/IP protocol on each PC
¾ Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari
2.2 Installation Environment Requirements
¾ Place the Router in a well ventilated place far from any heater or heating vent
¾ Avoid direct irradiation of any strong light (such as sunlight)
¾ Keep at least 2 inches (5 cm) of clear space around the Router
¾ Operating Temperature: 0℃~40℃ (32℉~104℉)
¾ Operating Humidity: 10%~90%RH, Non-condensing
2.3 Connecting the Router
Before installing the Router, make sure your PC is connected to the Internet through the
broadband service successfully. If there is any problem, please contact your ISP. After that, please
install the Router according to the following steps. Don't forget to pull out the power plug and keep
your hands dry.
1. Power off your Cable/DSL Modem, and the Router.
2. Locate an optimum location for the Router. The best place is usually at the center of your
wireless network.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
4. Connect the DSL/Cable Modem to the Internet port of the Router, shown in Figure 2-1.
5. Connect the PC(s) and each Switch/Hub in your LAN to the Ethernet ports on the Router,
shown in Figure 2-1. If you have the wireless NIC and want to use the wireless function, you
can skip this step.
- 7 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
6. Connect the power adapter to the power socket on the Router, and the other end into an
electrical outlet, shown in Figure 2-1. The Router will start to work automatically.
7. Power on your Cable/DSL Modem.
Figure 2-1 Hardware Installation
Figure 2-2 USB Installation
Note:
)
If you want to use the Router to share files or printer, plug the USB storage device to the USB port
or connect the printer to the Router with a matching cable.
- 8 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Chapter 3. Quick Installation Guide
This chapter will show you how to configure the basic functions of your N600 Wireless Dual
Band Gigabit Router using Quick Setup Wizard within minutes.
3.1 TCP/IP Configuration
The default IP address of the Router is 192.168.0.1 and the default Subnet Mask is 255.255.255.0.
These values can be changed as you desire. In this guide, we use all the default values for
description.
Connect the local PC to the Ethernet ports of the Router and then you can configure the IP
address for your PC by the following method: Set up the TCP/IP Protocol in "Obtain an IP
address automatically" mode on your PC. If you need instructions as to how to do this, please
refer to Appendix B: Configuring the PC
the PC.
Now, you can run the Ping command in the command prompt to verify the network connection
between your PC and the Router. The following example is in Windows 2000 OS.
Open a command prompt, and type ping 192.168.0.1, and then press Enter.
¾ If the result displayed is similar to the Figure 3-1, it means the connection between your PC
and the Router has been established well.
. Then the built-in DHCP server will assign IP address for
Figure 3-1 Success result of Ping command
¾ If the result displayed is similar to Figure 3-2, it means the connection between your PC and
the Router failed.
- 9 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Figure 3-2 Failure result of Ping command
Please check the connection following these steps:
1. Is the connection between your PC and the Router correct?
Note:
)
The 1/2/3/4 LEDs of Ethernet ports which you link to on the Router and LEDs on your PC's
adapter should be lit.
2. Is the TCP/IP configuration for your PC correct?
)
If the Router's IP address is 192.168.0.1, your PC's IP address must be within the range of
192.168.0.2 ~ 192.168.0.254.
3. Is the default LAN IP of the Router correct?
Note:
) Note:
If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the
Router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in
order to verify the network connection between your PC and the Router, you can open a
command prompt, and type ping 192.168.1.1, and then press Enter.
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage the N600 Wireless Dual Band Gigabit
Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web
browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type in the default IP address
http://tplinklogin.net
in the address field.
- 10 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Figure 3-3 Log in the Router
After a moment, a login window will appear, similar to Figure 3-4. Enter admin for the User
Name and Password, both in lower case letters. Then click the OK button or press the Enter
key.
Figure 3-4 Login Windows
Note:
)
If the above screen does not pop up, it means that your Web-browser has been set to a proxy.
Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears,
cancel the Using Proxy checkbox, and click OK to finish it.
2. After successfully log in, you can click the Quick Setup menu to quickly configure your
Router.
Figure 3-5 Quick Setup
3. Click Next, and then WAN Connection Type page will appear, shown in Figure 3-6. The
Router provides Auto-Detect function and supports three popular ways Dynamic IP, Static
- 11 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
IP and PPPoE to connect to the Internet. It’s recommended that you make use of the
Auto-Detect function. If you are sure of what kind of connection type your ISP provides, you
can select the very type and click Next to go on configuring.
Figure 3-6 WAN Connection Type
4. If you select Auto-Detect, the Router will automatically detect the connection type your ISP
provides. Make sure the cable is securely plugged into the Internet port before detection. The
appropriate configuration page will be displayed when an active Internet service is
successfully detected by the Router.
1) If the connection type detected is PPPoE, the next screen will appear as shown in Figure
3-7.
Figure 3-7 Quick Setup - PPPoE
¾ User Name/Password - Enter the User Name and Password provided by your ISP.
These fields are case-sensitive. If you have difficulty with this process, please contact
your ISP.
¾ Confirm Password - Enter the password again to make sure that the password is
correct.
2) If the connection type detected is Dynamic IP, the next screen will appear as shown in
Figure 3-8. A MAC address is a 12-digit code assigned to a unique piece of hardware for
identification. Some ISPs will register the MAC address of your computer when you
access the Internet for the first time via the cable/ADSL modem they offered. If you add a
router into your network to share the Internet, the ISP may not recognize the new MAC
- 12 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
address of the router and will not offer the Internet connection any more. Therefore, it is
necessary to clone the MAC address of the computer to the router.
Figure 3-8 Quick Setup – MAC Clone
¾ If you are visiting the Router from the main computer, please select Yes, and then click
Next.
¾ If you are visiting the Router from another computer rather than the main computer,
please select No, and then click Next.
Note:
)
1) It’s strongly recommended that you visit and configure the Router from the main
computer.
2) To find the main computer’s MAC, please go to Start > Run on your main computer, type
in cmd and press Enter. At the command prompt, enter ipconfig/all and press Enter.
The MAC will be displayed as Physical Address, shown in Figure 3-9.
Figure 3-9 Find MAC Address
- 13 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
3) If the connection type detected is Static IP, the next screen will appear as shown in Figure
3-10. Configure the following parameters and then click Next to continue.
Figure 3-10 Quick Setup - Static IP
¾ IP Address - This is the WAN IP address as seen by external users on the Internet
(including your ISP). Your ISP will provide you with the IP address you need to enter
here. Enter the IP address into the field.
¾ Subnet Mask - The Subnet Mask is used for the WAN IP address. Your IPS will provide
you with the subnet mask which is usually 255.255.255.0.
¾ Default Gateway - Your ISP will provide you with the Gateway address which is the ISP
server’s address. Enter the gateway IP address into the box if required.
¾ Primary DNS - Enter the DNS Server IP address into the box if required.
¾ Secondary DNS - If your ISP provides another DNS server, enter it into this field.
5. After finishing WAN Connection Type selection, the Dual Band Selection page will appear as
shown in Figure 3-11. Here we choose “Concurrently with 2.4GHz and 5GHz (802.11a/b/g/n)”
for introduction. Click Next to continue.
Figure 3-11 Quick Setup – Dual Band Selection
¾ 2.4GHz - You can use the 2.4GHz band to connect to many classic wireless devices like
gaming consoles, laptops, DVRs, ect.
- 14 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
¾ 5GHz - This band is less crowded and is used for time-sensitive music, video streaming
or gaming. Using this band can avoid interference with 2.4GHz networks or noisy
devices like cordless phones and microwave ovens.
6. Configure the basic parameters for 2.4GHz wireless network in the following screen as
shown in Figure 3-12, and then click Next.
Figure 3-12 Quick Setup – Wireless
¾ Wireless Radio - Displays whether the wireless function is enabled or not.
¾ Wireless Network Name - Also called the SSID (Service Set Identification). Enter a
value of up to 32 characters. The same name must be assigned to all wireless devices
in your network. The default SSID is set to be TP-LINK_2.4GHz_XXXXXX. This value is
case-sensitive. For example, TEST is NOT the same as test.
¾ Region - Select your region from the drop-down list. This field specifies the region
where the wireless function of the Router can be used. It may be illegal to use the
wireless function of the Router in a region other than one of those specified in this field.
If your country or region is not listed, please contact your local government agency for
assistance.
Note:
)
Limited by local law regulations, version for North America does not have region
selection option.
¾ Band - This field displayed the operating frequency being configured.
¾ Mode - This field determines the wireless mode which the Router works on.
- 15 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
z 11b only - Select if all of your wireless clients are 802.11b.
z 11g only - Select if all of your wireless clients are 802.11g.
z 11n only- Select only if all of your wireless clients are 802.11n.
z 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.
z 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless
clients.
¾ Channel Width - Select any channel width from the drop-down list. The default setting
is “Auto”, which can adjust the channel width for your clients automatically.
¾ Channel - This field determines which operating frequency will be used. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point. If you select “Auto”, then the AP will select the best
channel automatically.
¾ Wireless Security
z Disable Security - The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the Router without
encryption.
z Enable Security (WPA-PSK/WPA2-PSK) – It’s selected by default, with the
default PSK password the same as the default PIN code.
z No Change - If you chose this option, wireless security configuration will not
change!
These settings are only for basic wireless parameters. For advanced settings, please refer to
4.6 Wireless 2.4GHz
.
7. Configure the basic parameters for 5GHz wireless network in the following screen as shown
in Figure 3-13, and then click Next.
- 16 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Figure 3-13 Quick Setup – Wireless
¾ Wireless Radio - Choose from the drop-down list to enable or disable the wireless
radio.
¾ Wireless Network Name - Also called the SSID (Service Set Identification). Enter a
value of up to 32 characters. The same name must be assigned to all wireless devices
in your network. The default SSID is set to be TP-LINK_5GHz_XXXXXX. This value is
case-sensitive. For example, TEST is NOT the same as test.
¾ Region - Select your region from the drop-down list. This field specifies the region
where the wireless function of the Router can be used. It may be illegal to use the
wireless function of the Router in a region other than one of those specified in this field.
If your country or region is not listed, please contact your local government agency for
assistance.
Note:
)
Limited by local law regulations, version for North America does not have region
selection option.
¾ Band - This field displayed the operating frequency being configured.
¾ Mode - This field determines the wireless mode which the Router works on.
z 11a only - Select if all of your wireless clients are 802.11a.
z 11n only- Select only if all of your wireless clients are 802.11n.
z 11an mixed - Select if you are using both 802.11a and 802.11n wireless clients.
¾ Channel Width - Select any channel width from the drop-down list. The default setting
is “Auto”, which can adjust the channel width for your clients automatically.
- 17 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
¾ Channel - This field determines which operating frequency will be used. It is not
necessary to change the wireless channel unless you notice interference problems with
another nearby access point. If you select “Auto”, then the AP will select the best
channel automatically.
¾ Wireless Security
z Disable Security - The wireless security function can be enabled or disabled. If
disabled, the wireless stations will be able to connect the Router without
encryption.
z Enable Security (WPA-PSK/WPA2-PSK) – It’s selected by default, with the
default PSK password the same as the default PIN code.
z No Change - If you chose this option, wireless security configuration will not
change!
These settings are only for basic wireless parameters. For advanced settings, please refer to
4.7 Wireless 5GHz
.
8. Then you will see the Finish page.
¾ If you don’t make any change on the Wireless page, you will see the Finish page as
shown in Figure 3-14. Click the Finish button to finish the Quick Setup.
Figure 3-14 Quick Setup - Finish
¾ If there is anything changed on the Wireless page, you will see the Finish page as
shown in Figure 3-15. Click the Reboot button to make your wireless configuration take
effect and finish the Quick Setup.
Figure 3-15 Quick Setup – Finish
- 18 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Chapter 4. Configuring the Router
This chapter will show each Web page's key functions and the configuration way.
4.1 Login
After your successful login, you will see the sixteen main menus on the left of the Web-based utility.
On the right, there are the corresponding explanations and instructions.
The detailed explanations for each Web page’s key function are listed below.
4.2 Status
The Status page provides the current status information about the Router. All information is
read-only.
- 19 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
Figure 4-1 Router Status
- 20 -
TL-WDR3600 N600 Wireless Dual Band Gigabit Router
4.3 Quick Setup
Please refer to 3.2 Quick Installation Guide.
4.4 Network
Figure 4-2 the Network menu
There are three submenus under the Network menu (shown in Figure 4-2): WAN, LAN and MAC
Clone. Click any of them, and you will be able to configure the corresponding function.
4.4.1 WAN
Choose menu “Network → WAN”, you can configure the IP parameters of the WAN on the
screen below.
1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will
automatically get IP parameters from your ISP. You can see the page as follows (Figure
4-3):
Figure 4-3 WAN – Dynamic IP
- 21 -
Loading...