TP Link WA901NDV4 User Manual

TL-WA901ND

450Mbps Wireless N Access Point

REV2.0.0 1910010841

Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1） This device may not cause harmful interference.

2） This device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 24 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1) cet appareil ne doit pas provoquer d’interférences et

(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.

This device has been designed to operate with the antennas listed below, and having a maximum gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

Industry Canada Statement

Complies with the Canadian ICES-003 Class B specifications.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice

注意！

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響，請妥適使用。

安全諮詢及注意事項

●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

●注意防潮，請勿將水或其他液體潑灑到本產品上。

●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock

and voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

This product can be used in the following countries:

AT BG BY CA CZ DE DK EE

ES FI FR GB GR HU IE IT

LT LV MT NL NO PL PT RO

RU SE SK TR UA US

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 450Mbps Wireless N Access Point

Model No.: TL-WA901ND

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents

EN 300 328 V1.8.1

EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1

EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011

EN 50385: 2002

The product carries the CE Mark:

Person responsible for marking this declaration:

Yang Hongliang

Product Manager of International Business

Date of issue:2015

TP-LINK TECHNOLOGIES CO., LTD.

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan

Rd, Nanshan, Shenzhen, China

CONTENTS

Package Contents .................................................................................................... 1

Chapter 1 Introduction ........................................................................................... 2

1.1 Product Overview ............................................................................................ 2

1.2 Conventions .................................................................................................... 2

1.3 Main Features ................................................................................................. 3

1.4 Appearance ..................................................................................................... 3

1.4.1 The Front Panel ................................................................................................. 3

1.4.2 The Rear Panel.................................................................................................. 4

Chapter 2 Hardware Installation ........................................................................... 6

2.1 Before You Begin ............................................................................................ 6

2.2 Basic Requirements ........................................................................................ 6

2.3 Connecting the Device .................................................................................... 6

Chapter 3 Quick Installation Guide ....................................................................... 9

3.1 Quick Setup ..................................................................................................... 9

Chapter 4 Configure the Device .......................................................................... 17

4.1 Login ............................................................................................................. 17

4.2 Status ............................................................................................................ 18

4.3 Quick Setup ................................................................................................... 19

4.4 WPS .............................................................................................................. 19

4.5 Network ......................................................................................................... 25

4.5.1 LAN .................................................................................................................. 26

4.5.2 DHCP Settings ................................................................................................. 26

4.5.3 DHCP Client List .............................................................................................. 28

4.6 Wireless ........................................................................................................ 28

4.6.1 Wireless Settings ............................................................................................. 29

4.6.2 Wireless Security ............................................................................................. 40

4.6.3 Wireless MAC Filtering .................................................................................... 52

4.6.4 Wireless Advanced .......................................................................................... 54

4.6.5 Wireless Statistics............................................................................................ 55

4.6.6 Throughput Monitor ......................................................................................... 55

4.7 System Tools ................................................................................................. 56

4.7.1 SNMP .............................................................................................................. 57

4.7.2 Diagnostic ........................................................................................................ 58

4.7.3 Ping Watch Dog ............................................................................................... 60

4.7.4 Firmware Upgrade ........................................................................................... 61

4.7.5 Factory Defaults............................................................................................... 62

4.7.6 Backup & Restore ............................................................................................ 62

4.7.7 Reboot ............................................................................................................. 63

4.7.8 Password ......................................................................................................... 63

4.7.9 System Log ...................................................................................................... 64

Appendix A: Application Example ........................................................................ 65

Appendix B: Factory Defaults ............................................................................... 68

Appendix C: Troubleshooting ............................................................................... 69

Appendix D: Specifications ................................................................................... 70

Appendix E: Glossary ............................................................................................ 71

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Package Contents

 The following items should be found in your package:

 One TL-WA901ND 450Mbps Wireless N Access Point

 One Power Injector

 Ethernet Cable

 One Power Adapter for TL-WA901ND 450Mbps Wireless N Access Point

 Quick Installation Guide

 One Resource CD for TL-WA901ND 450Mbps Wireless N Access Point, including:

 This User Guide

 Other helpful information

Note:



Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your distributor.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Chapter 1 Introduction

1.1 Product Overview

The TL-WA901ND 450Mbps Wireless N Access Point is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It allows for greater range and mobility within your wireless network while also allowing you to connect the wireless devices to a wired environment. Increased mobility and the absence of cabling will be beneficial for your network.

With using IEEE 802.11n wireless technology, your device can transmit wireless data at the rate of up to 450Mbps. With multiple protection measures, including SSID broadcast control and wireless LAN 64/128/152-bit WEP encryption, WiFi protected Access (WPA2- PSK, WPA- PSK), the TL-WA901ND 450Mbps Wireless N Access Point delivers complete data privacy. This device leverages some 802.11n features to provide improved performance and coverage compared to

802.11a/g devices, and fully interoperates with 802.11n products if they are Wi-Fi CERTIFIED.

It supports an easy, web-based setup for installation and management. Even though you may not be familiar with the Access Point, you can easily configure it with the help of this Guide. Before installing the AP, please look through this Guide to get the full information of the TL-WA901ND 450Mbps Wireless N Access Point.

1.2 Conventions

The AP or TL-WA901ND, or device mentioned in this user guide stands for TL-WA901ND 450Mbps Wireless N Access Point without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

1.3 Main Features

 Wireless speed up to 450Mbps

 Supports Access Point, Multi-SSID, Client, Repeater（Universal Repeater）and Bridge with AP

modes

 Up to 4 SSIDs and VLAN support

 Up to 30 meters (100 feet) of flexible deployment with included Power over Ethernet Injector

 Easily setup a WPA encrypted secure connection at a push of the WPS button

 Supports Remote and Web management

 Backward compatible with 802.11b/g products

1.4 Appearance

1.4.1 The Front Panel

Figure 1-1

The front panel of the TL-WA901ND consists of several LED indicators, which is designed to indicate connections. View from left to right, Table 1-1 describes the LEDs on the front panel of the device.

LED Explanation

Name Status Indication

Off No Power.

On Power on.

Off

Flashing

Off

Flashing

Slow Flash

Quick Flash

There is no device linked to the corresponding port.

There is a device linked to the corresponding port but no activity.

There is an active device linked to the corresponding port.

The Wireless function is disabled.

The Wireless function is enabled.

A wireless device is connecting to the network by WPS function. This process will last in the first 2 minutes.

A wireless device has been successfully added to the network by WPS function.

A wireless device failed to be added to the network by WPS function.

Table 1-1

1.4.2 The Rear Panel

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Figure 1-2

Viewed from left to right, the following parts are located on the rear panel of TL-WA901ND.

ON/OFF: The switch for the power.

POWER: The power port connects to the power adapter provided with the TL-WA901ND

450Mbps Wireless N Access Point.

Ethernet: One LAN 10/100Mbps RJ45 port connects to a network device, such as a switch or a

router.

WPS/RESET: This button is used for both WPS and Reset function. To use the WPS function, press it for less than five seconds; to use the RESET function, press it for more than five seconds.

 Used as RESET button:

There are two ways to reset to the Router's factory defaults:

1) Use the Factory Defaults function on System Tools -> Factory Defaults page in the Router's Web-based Utility.

2) Use the WPS/RESET button: With the Router powered on, press and hold the WPS/RESET button (more than 5 seconds) until the SYS LED becomes quick-flash from slow-flash. Then release the button and wait the Access Point to reboot to its factory default settings.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

 Used as WPS button:

If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can press this button to quickly establish a connection between the Access Point and client devices and automatically configure wireless security for your wireless network.

Wireless antenna: The external antenna is used to transmit and receive wireless data.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Chapter 2 Hardware Installation

2.1 Before You Begin

Please read this User Guide carefully before installing and using the equipment. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary base on the types of materials and background RF (radio frequency) noise in your home or office.

For best performance of your wireless network, you are suggested to:

1). Avoid redundant obstacles and interference between the wireless devices.

2). Keep your AP away from appliances with a strong electric field or magnetic field, such as a microwave oven or refrigerator.

3). Place the AP near the center of the area in which your computers operates.

2.2 Basic Requirements

 Use only the power adapter provided with your AP

 Place your AP in a well ventilated place far from direct sunlight, any heater or heating vent

 Leave at least 2 inches (5cm) space around the device for heat dissipation

 Turn off your AP and unplug the power adapter in a lighting storm to avoid damage

 Web browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or

above

 Operating temperature: 0℃~40℃ (32℉~104℉)

 Operating Humidity: 10%~90%RH, Non-condensing

2.3 Connecting the Device

Figure 2-1 is an example of the typical application of TL-WA901ND in the infrastructure network. An Infrastructure network contains an access point or a wireless router.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Figure 2-1 The Example of Infrastructure Network Incorporating the TL-WA901ND

To establish a typical connection of the AP, please take the following steps:

1. Connect the Cable or DSL modem to a Router.

2. Locate an optimum location for the AP. The best place is usually near the center of the area in which your wireless devices like PCs, smart phones will wirelessly connect.

3. Adjust the direction of the antenna. Normally, upright is a good direction.

4. Connect the Ethernet Broadband Router to the TL-WA901ND Access Point. Power on the AP.

5. Then you can connect a desktop PC or laptop to your network. (Make sure your computer or laptop is equipped with a Wireless Adapter and the IP address is configured as obtain an IP address automatically.)

Note:



If you are not so clear about how to connect your devices to the network, please refer to Appendix

A Application Example.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Note:



The diameter of the screw, 3.5mm<D<7.8mm, and the distance of two screws is 107.5mm. The screw that project from the wall need around 4mm based, and the length of the screw need to be at least 20mm to withstand the weight of the product.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Chapter 3 Quick Installation Guide

This chapter will guide you to configure your PC to communicate with the AP and to configure and manage the TL-WA901ND 450Mbps Wireless N Access Point easily with a Web-based utility.

3.1 Quick Setup

With a Web-based utility, it is easy to configure and manage the TL-WA901ND 450Mbps Wireless N Access Point. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.

Note:



If you cannot access the web-based configuration page, please refer to T3 in Appendix C:

Troubleshooting for help.

1. To access the configuration utility, open a web-browser and type in the default address

http://tplinkap.net

in the address field of the browser and press Enter.

Figure 3-1 Login to the AP

After a moment, a login window will appear, similar to the Figure 3-2. Enter the default values for the User Name and Password (both are admin in lower case letters). Then click OK or press Enter.

Enter the default values for the User Name and Password (both are admin in lower case letters) in Figure 4-2 below. Then click Login or press Enter.

Figure 3-2 Login Windows

Note:



If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.

2. After successfully logging in, the Quick Setup page will display. Click Next to continue.

3. The Quick Setup Start page will display. Click Next to continue.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Figure 3-3 Quick Setup

Figure 3-4 Quick Setup

Note:



By selecting YES for Change the login account, you can modify your login user name and password. In this case, it is suggested that you record them in some place easy to find.

4. The Operation Mode page will appear then, shown in Figure 3-5. The TL-WA901ND

supports up to five operation modes.

Figure 3-5 Operation Mode

TL-WA901ND 450Mbps Wireless N Access Point User Guide

 In Access Point mode, the product will act as a wireless central hub for your wireless

LAN clients, giving a wireless extension for your current wired network.

 In Repeater(Range Extender) mode, the product can extend the coverage of your main

Router/AP.

 In Bridge with AP mode, the product can wirelessly connect two or more remote LANs

together.

 In Client mode, the product will act as a wireless adapter to connect your wired devices

(e.g. IPTV Set-top-box, Smart TVs, Game Consoles, DVD and Blu-ray Players, etc.) to a wireless network.

 In Multi-SSID mode, the product can be assigned up to four SSIDs to work with your

VLAN.

5. Select the operation mode based on your need.

A. When you choose Access Point mode, the Wireless Settings page will be shown in Figure

3-6.

Figure 3-6 Wireless Setting - Access Point mode

1) Create an easy-to-remember and distinguish name for your wireless network, write it into Wireless Network Name(SSID).

2) Select Channel for your device.

3) It's recommended select Most Secure (WPA/WPA2-PSK) encryption mode and enter a password below to prevent unauthorized access to your AP.

4) Click Next, you will then come to Network Setting page for furthers configuration.

B. When you choose Repeater (Range Extender) mode, the AP will detect the wireless

networks in your neighborhood, and then the window displaying a list of available SSIDs will appear in Figure 3-7.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Figure 3-7 AP List

1) Find the SSID of the Access Point / Router or WISP which you want you to connect to, and click Connect in the corresponding row. You will then see the page shown in Figure 3-8.

2) Select the security mode and enter the password that is the same as on your router or access point in Figure 3-8.

3) Click Next, you will then come to Network Settings page for furthers configuration.

Figure 3-8 Wireless Setting – Repeater (Range Extender) mode

C. When you choose Bridge with AP mode, the AP will detect the wireless networks in your

neighborhood, and then the window displaying a list of available SSIDs will appear in Figure 3-9.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Figure 3-9 AP List

1) Find the SSID of the Access Point / Router or WISP which you want you to connect to, and click Connect in the corresponding row. You will then see the page shown in Figure 3-10.

2) Select the security mode and enter the password that is the same as on your router or access point in Wireless Bridge Setting.

3) You can name the bridge AP in Local Wireless Name, and configure the Local Wireless Setting for the bridge AP.

4) Click Next in Figure 3-10, and you will come to Network Settings page for furthers configuration.

Figure 3-10 Wireless Setting – Bridge with AP mode

TL-WA901ND 450Mbps Wireless N Access Point User Guide

D. When you choose Client mode, the AP will detect the wireless networks in your

neighborhood, and then the window displaying a list of available SSIDs will appear in Figure 3-11.

Figure 3-11 AP List

1) Find the SSID of the Access Point / Router or WISP which you want you to connect to, and click Connect in the corresponding row. You will then see the page shown in Figure 3-12.

2) Select the security mode and enter the password that is the same as on the main Router/AP.

3) Click Next, you will then come to Network Settings page for furthers configuration.

Figure 3-12 Wireless Setting – Client mode

E. When you choose Multi-SSID mode, the Wireless Settings page will be shown in Figure

3-13.

TL-WA901ND 450Mbps Wireless N Access Point User Guide

Figure 3-13 Wireless Setting – Multi-SSID mode

You are suggested to implement Multi-SSID function with a switch that supports Tag VLAN feature. For advanced configuration of this step, please refer to explanations of this mode in

Wireless Settings.

6. When you have configured Wireless Settings in step 4, The Network Settings page will appear then, shown in Figure 3-14. It is recommended that you keep the default settings on this page.

4.6.1

Figure 3-14 Network Setting

Note:



These settings are only for basic wireless parameters, for advanced settings, please refer to

4.5 Network

TL-WA901ND 450Mbps Wireless N Access Point User Guide

7. Click the Next button. You will then see the Finish page. Here takes the settings for Access Point mode for example.

Check your settings and click Save to save your settings for future reference.

Click the Finish button to finish the configuration of the Access Point.

Figure 3-15 Quick Setup – Finish

+ 56 hidden pages