TP Link WA830RE User Manual

TL-WA830RE

300Mbps Wireless N Range Extender

Rev: 1.0.0 1910010538

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2011 TP-LINK TECHNOLOGIES CO., LTD.

All rights reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

	Country	Restriction	Reason/remark
	Bulgaria	None	General authorization required for outdoor use and
			public service

Outdoor use limited to 10 France mW e.i.r.p. within the band

2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

	Italy	None	If used outside of own premises, general authorization is
			required
	Luxembourg	None	General authorization required for network and service
			supply(not for spectrum)
	Norway	Implemented	This subsection does not apply for the geographical area
			within a radius of 20 km from the centre of Ny-Ålesund
	Russian Federation	None	Only for indoor applications

Note: Please don’t use the product outdoors in France.

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 300Mbps Wireless N Range Extender

Model No.: TL-WA830RE

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC

The above product is in conformity with the following standards or other normative documents

ETSI EN 300 328 V1.7.1: 2006

ETSI EN 301 489-1 V1.8.1:2008& ETSI EN 301 489-17 V2.1.1:2009 EN60950-1:2006

Recommendation 1999/519/EC

EN62311:2008

Directives 2004/108/EC

The above product is in conformity with the following standards or other normative documents

EN 55022:2006 +A1:2007

EN 55024:1998+A1:2001+A2:2003 EN 61000-3-2:2006

EN 61000-3-3:1995+A1:2001+A2:2005

Directives 2006/95/EC

The above product is in conformity with the following standards or other normative documents

EN60950-1:2006

Directive ErP 2009/125/EC

Audio/Video, information and communication technology equipmentEnvironmentally conscious design

EN62075:2008

Person is responsible for marking this declaration:

Yang Hongliang

Product Manager of International Business

TP-LINK TECHNOLOGIES CO., LTD.

South Building, No.5 Keyuan Road, Central Zone, Science & Technology Park, Nanshan,

Shenzhen, P. R. China

Industry Canada Statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes:

(1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

NOTE IMPORTANTE:

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

NCC Notice:

機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Korea Warning Statements

		CONTENTS
Package Contents .....................................................................................................			I
Chapter 1	Introduction...........................................................................................		1
1.1	Product Overview..............................................................................................		1
1.2	Main Features ...................................................................................................		2
1.3	Appearance.......................................................................................................		2
	1.3.1	The Front Panel .................................................................................................	2
	1.3.2	The Rear Panel ..................................................................................................	3
Chapter 2	Hardware Installation ...........................................................................		4
2.1	Before You Begin..............................................................................................		4
2.2	Basic Requirements..........................................................................................		4
2.3	Connecting the Device......................................................................................		4
Chapter 3 Quick Installation Guide.......................................................................			6
3.1	Configure the PC ..............................................................................................		6
3.2	Quick Setup ......................................................................................................		9
Chapter 4 Configure the Device..........................................................................			17
4.1	Status	..............................................................................................................	17
4.2	Quick ....................................................................................................Setup		18
4.3	Range ..............................................................................................Extender		18
4.4	Network...........................................................................................................		23
4.5	Wireless ..........................................................................................................		23
	4.5.1 .............................................................................................	Wireless Settings	24
	4.5.2 .............................................................................................	Wireless Security	27
	4.5.3 ....................................................................................	Wireless MAC Filtering	32
	4.5.4 ..........................................................................................	Wireless Advanced	34
	4.5.5 .........................................................................................	Throughput Monitor	35
	4.5.6 ............................................................................................	Wireless Statistics	36
4.6	DHCP..............................................................................................................		36
	4.6.1 .................................................................................................	DHCP Settings	37
	4.6.2 ............................................................................................	DHCP Clients List	38
	4.6.3 .......................................................................................	Address Reservation	38
4.7	System ..................................................................................................Tools		39
	4.7.1 ..............................................................................................................	SNMP	40
	4.7.2 ........................................................................................................	Diagnostic	41
	4.7.3 ...............................................................................................	Ping Watch Dog	43
	4.7.4 ...........................................................................................	Firmware Upgrade	44

4.7.5	Factory Defaults...............................................................................................	45
4.7.6	Backup & Restore............................................................................................	45
4.7.7	Reboot .............................................................................................................	46
4.7.8	Password .........................................................................................................	47
4.7.9	System Log......................................................................................................	47
Appendix A: Application Example........................................................................		49
Appendix B: Factory Defaults ...............................................................................		52
Appendix C: Troubleshooting...............................................................................		53
Appendix D: Specifications...................................................................................		54
Appendix E: Glossary............................................................................................		55

Package Contents

The following items should be found in your package:

¾One TL-WA830RE 300Mbps Wireless N Range Extender

¾Ethernet Cable

¾One Power Adapter for TL-WA830RE 300Mbps Wireless N Range Extender

¾Quick Installation Guide

¾One Resource CD for TL-WA830RE 300Mbps Wireless N Range Extender, including: z This User Guide

z Other helpful information

) Note:

Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact with your distributor.

Conventions

The AP or TL-WA830RE,or Device mentioned in this User guide stands for TL-WA830RE 300Mbps Wireless N Range Extender without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand.

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

Chapter 1 Introduction

Thank you for choosing the TL-WA830RE 300Mbps Wireless N Range Extender.

1.1Product Overview

The TL-WA830RE 300Mbps Wireless N Range Extender is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It allows for greater range and mobility within your wireless network while also allowing you to connect the wireless devices to a wired environment. Increased mobility and the absence of cabling will be beneficial for your network.

With using IEEE 802.11n wireless technology, your device can transmit wireless data at the rate of up to 300Mbps. With multiple protection measures, including SSID broadcast control and wireless LAN 64/128/152-bit WEP encryption, WiFi protected Access (WPA2-PSK, WPA-PSK), the TL-WA830RE 300Mbps Wireless N Range Extender delivers complete data privacy.

It supports an easy, web-based setup for installation and management. Even though you may not be familiar with the Access Point, you can easily configure it with the help of this Guide. Before installing the AP, please look through this Guide to get the full information of the TL-WA830RE 300Mbps Wireless N Range Extender.

1

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

1.2Main Features

¾Make use of IEEE 802.11n wireless technology

¾Provides multiple encryption security Types including: 64/128/152-bit WEP WPA/WPA2 WPA-PSK/WPA2-PSK

¾Supports Built-in DHCP server

¾Supports MAC address filtering

¾Supports multiple operating modes including: Range Extender, Access Point

¾Supports Firmware Upgrade

¾Supports Remote and Web management

1.3Appearance

1.3.1 The Front Panel

Figure 1-1

The front panel of the TL-WA830RE consists of several LED indicators, which is designed to indicate connections. View from left to right, Table 1-1 describes the LEDs on the front panel of the device.

LED Explanation

	Name		Status		Indication
	Power		Off	No Power
			On		Power on
			Off	The device has a system error
	System		On		The device is initialising
			Flashing	The device is working properly
			Off		There is no device linked to the corresponding port
	LAN		On		There is a device linked to the corresponding port but no activity
			Flashing	There is an active device linked to the corresponding port
	WLAN		Off		The Wireless function is disabled
			Flashing		The Wireless function is enabled
			On		The Range Extender has connected the Router successfully
	Range Extender		Flashing		The Range Extender is connecting the Router
			Off		The Range Extender has not connected any Router yet
					Table 1-1

2

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

1.3.2 The Rear Panel

Figure 1-2

Viewed from left to right, the following parts are located on the rear panel of TL-WA830RE.

Wireless antenna The external antenna is used to transmit and receive wireless data.

POWER: The power port connects to the power adapter provided with the TL-WA830RE 300Mbps Wireless N Range Extender.

LAN: One LAN 10/100Mbps RJ45 port connects to a network device, such as a switch or a router.

RESET: The Reset button is used to restore the AP’s factory default settings. There are two ways to reset the Access Point’s factory defaults:

zMethod one: With the AP powered on, use a pin to press and hold the Reset button (about 5 seconds) until the System LED becomes quick-flash from slow-flash. And then release the button and wait the AP to reboot to its factory default settings.

zMethod two: Restore the default settings from “System Tools > Factory Defaults” of the AP's Web-based management page.

) Note:

Ensure the AP is powered on before it restarts completely.

3

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

Chapter 2 Hardware Installation

2.1Before You Begin

Please read this User Guide carefully before installing and using the equipment. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary base on the types of materials and background RF (radio frequency) noise in your home or office.

For best performance of your wireless network, you are suggested to:

1). Avoid redundant obstacles and interference between the wireless devices.

2). Keep your AP away from appliances with a strong electric field or magnetic field, such as a microwave oven or refrigerator.

Place the AP near the center of the area in which your computers operates.

2.2Basic Requirements

zUse only the power adapter provided with your AP

zThe electrical outlet shall be installed near the device and shall be easily accessible

zPlace your AP in a well ventilated place far from direct sunlight, any heater or heating vent

zLeave at least 2 inches (5cm) space around the device for heat dissipation

zTurn off your AP and unplug the power adapter in a lighting storm to avoid damage

zWeb browser, such as Microsoft Internet Explorer 5.0 or above, Netscape Navigator 6.0 or above

zOperating temperature: 0 ~40 (32 ~104 )

zOperating Humidity: 10%~90%RH, Non-condensing

2.3Connecting the Device

Figure 2-1 is an example of the typical application of TL-WA830RE in the infrastructure network. An Infrastructure network contains an access point or a wireless router.

4

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

Figure 2-1 The Example of Infrastructure Network Incorporating the TL-WA830RE

To establish a typical connection of the AP, please take the following steps:

1.Connect the Cable or DSL modem to a Router.

2.Locate an optimum location for the AP. The best place is usually near the center of the area in which your PC(s) will wirelessly connect.

3.Adjust the direction of the antenna. Normally, upright is a good direction.

4.Connect the Ethernet Broadband Router to the TL-WA830RE Access Point. Power on the AP.

5.Then you can connect a desktop PC or laptop to your network. (Make sure your computer or laptop is equipped with a Wireless Adapter.)

) Note:

If you are not so clear about how to connect your devices to the network, please refer to Appendix A Application Example.

5

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

Chapter 3 Quick Installation Guide

This chapter will guide you to configure your PC to communicate with the AP and to configure and manage the TL-WA830RE 300Mbps Wireless N Range Extender easily with a Web-based utility.

3.1Configure the PC

The wireless adapter-equipped computers in your network must be in the same IP Address range without overlap with each other. Manually configure the IP address as 192.168.0.* (* is any integer between 1 to 253), and the Subnet mask as 255.255.255.0 for your PC by following the instructions below.

Connect the local PCs to the LAN ports on the AP and configure the IP address manually for your PCs.

1.Click Start (in the lower left corner of the screen), right-click My Network Connections and choose Properties.

Figure 3-1

2.On the My Network Connections window shown as Figure 3-2 below, right-click LAN (Local Area Connection) and choose Properties.

6

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

Figure 3-2

3.In the General tab of Internet Protocol (TCP/IP) Properties window, highlight Internet Protocol (TCP/IP) and click Properties.

Figure 3-3

7

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

4.Configure the IP address manually.

1)Select Use the following IP address.

2)Enter 192.168.0.* (* is any integer between 1 to 253) into the IP address filed, 255.255.255.0 into the Subnet mask filed and 192.168.0.254 into the Default gateway filed.

3)Click OK to keep your settings.

Figure 3-4

5.Verify the network connection between your PC and the AP via the Ping command. The following example is in Windows XP Operating System.

1)Click Start > Run tab. Enter cmd in the filed and click OK.

2)Type ping 192.168.0.254 on the screen that displays and then press Enter.

If the result displayed is similar to that shown as Figure 3-5 below, the connection between your PC and the AP has been successfully established.

Figure 3-5

8

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

If the result displayed is similar to that shown as Figure 3-6 below, it means that your PC has not connected to the AP.

Figure 3-6

Please check following these steps:

a)Check to see if your PC and the AP are right connected. The LED of LAN port which you link to on the device and the LED on your PC’s adapter should be lit up.

b)Make sure the TCP/IP for your PC is right configured. If the AP’s IP address is 192.168.0.254, your PC’s IP address must be within the range of 192.168.0.1 ~ 192.168.0.253.

3.2Quick Setup

With a Web-based utility, it is easy to configure and manage the TL-WA830RE 300Mbps Wireless N Range Extender. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.

1.To access the configuration utility, open a web-browser and type in the default address http://192.168.0.254 in the address field of the browser.

Figure 3-7 Login to the AP

After a moment, a login window will appear, similar to the Figure 3-8. Enter admin for the User Name and Password (both in lower case letters). Then click OK or press Enter.

Figure 3-8 Login Windows

9

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

) Note:

If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.

2.After successfully logging in, click the Quick Setup menu to quickly configure your AP and the following figure will display. Click Next to continue.

Figure 3-9 Quick Setup

3.And then Wireless page will appear shown in Figure 3-10. There are two Operation Modes, including Range Extender and Access Point. The available setting options are different in different operation modes, and they are explained below.

Figure 3-10 Quick Setup - Wireless

A.When you choose Range Extender, take the following steps:

1)Click Survey on the Wireless page shown as Figure 3-10 , and then AP List page will appear, shown in Figure 3-11.

10

TL-WA830RE 300Mbps Wireless N Range Extender User Guide

Figure 3-11 AP List

2)Find the SSID of the Access Point / Router you want to access, and click Connect in the corresponding row. For example, the first item is selected. The MAC address will be automatically filled into the corresponding box which is shown as the Figure 3-12 .

11