Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective hol ders.
This equipment has been tested and found to comply with the limits for a Class B digit al device,
pursuant to part 15 of the FCC Rules. These l imi ts are des ign ed to pr ovid e reas onabl e prot ect io n
against harmful interference in a residential installation. This equipment generat es, uses and can
radiate radio frequency energy and, if not ins talled and used in accordance wi th the instructions,
may cause harmful interference to radio com munications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to c orrect the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equi pment.
Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized
modifications to this equipment. Such modifications could void t he user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-locat ed or operating in conjunc tion with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and m ust not be co-located or operating in
conjunction with any other antenna or transm i tter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
cho
sen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fon
ctionnement est soumis aux deux conditions suivantes:
(1)cet appareil ne doit pas provoquer d’interférences et
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-cau
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
sing equipment regulations.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux
rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Where the MAINS plug is used as the disconnect device, the disconnect device shall remain
readily operable
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 150Mbps Universal WiFi Range Extender
Model No.: TL-WA750RE
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product wit hin the scope of Council Directives:
Directives 1999/5/EC, Directives 200 4/108/EC, Directives 2006/95/EC, Di rectives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
ETSI EN 300 328 V1.7.1: 2006
ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.1.1:2009
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN60950-1:2006+A11:2009+A1:2010+A12:2011
EN62311:2008
The product carries the CE Mark:
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of Issue: 2013
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
The following items should be found in your package:
TL-WA750RE 150Mbps Universal WiFi Range Extender
Ethernet Cable
Quick Installation Guide
Resource CD for TL-WA750RE 150Mbps Universal WiFi Range Ext ender, including only this
User Guide.
Note:
Make sure that the package contains the above items. If any of the lis ted items is damaged or
missing, please contact your distributor.
Conventions
The Range Extender, the Device or TL-WA750RE mentioned in this User guide stands for
TL-WA750RE 150Mbps Universal WiFi Range Extender without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may differ
from the actual situation. You can set the parameters according to your demand.
The power plug may differ f rom the picture illustrated in this UG due to different regional power
specifications. Here we just take that of EU version for example.
1
TL-WA750RE
150Mbps Universal WiFi Range Extender User Guide
Chapter 1 Introduction
1.1 Product Overview
The TL-WA750RE 150Mbps Universal WiFi Range Extender is dedicated to Small Office/Home
Office (SOHO) wireless network solutions. It will enlarge your existing wireless network and
mobility within your wireless network while also allowing you to connect a wired device to a
wireless environment. Increased mobility and the absence of cabling will be beneficial for your
network.
With using IEEE 802.11n wireless technology, t his devic e can transmi t wireles s data at the rate of
up to 150Mbps. With multiple protect ion measures, including wireless LAN 64/128/152-bit WEP
encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), the TL-WA750RE 150Mbps
Universal WiFi Range Extender delivers complete data privacy.
It supports an easy wireless connection to the root AP (equipped with WPS/QSS button) by
pressing the RE button on the front panel. It also supports an easy, web-based setup for
installation and management. Even though you may not be familiar with the Range Extender, you
can easily configure it with the help of this Guide. Before installing the Range Extende r, please
look through this Guide to get the full information of the TL-WA750RE 150Mbps Universal WiFi
Range Extender.
Supports built-in DHCP server
Supports two operating modes: Range E xt ender Mode 1 and Range Extender Mode 2
Supports firmware upgrade
Supports web management
1.3 Appearance
Figure 1-1
2
TL-WA750RE
150Mbps Universal WiFi Range Extender User Guide
The Range Extender is connected the router successfully.
The Range Extender is not connected any router yet.
Power on.
No signal at present.
Signal is transferring. And it also shows the current si gnal strength
connection.
LED Explanation:
Name Status Indication
On
RE
Flashing
The Range Extender is connecting the router.
Off
Off
Wireless
Flashing
The Wireless function is disabled.
The Wireless function is enabled.
Off No Power.
Power
On
Ethernet
Signal
Strength
Off
On
Flashing
Off
Solid
(1~5)
There is no device linked to the corresponding port.
There is a device linked to the corresponding port bu t no activity.
There is an active device linked to the correspondin g port.
the range extender received from the root AP after successful
Table 1-1
(RANGE EXTENDER/WPS): If your Wireless router or AP supports WPS or QSS
function, you can press the WPS or QSS button and then press the RANGE EXTENDER
button to establish a secure connecti on between the Wireless router (or AP ) and the Range
Extender TL-WA750RE.
RESET: This button is used to restore the Range Extender’s fact ory def ault settings.
There are two ways to reset the Range Extender’s factory defaults:
Method One: With the Range Extender powered on, use a pin t o press and hold the RESET
button (about 8 seconds) until the System LED becomes quick-flash from slow-flash. And
then release the button and wait the Range Extende r to reboot to its factory default settings.
Method Two: Restore the default settings from “System Tools > Factor y Defaults” of the
Range Extender's Web-based management page.
ETHERNET: One 10/100Mbps RJ45 Ethernet port used t o add wireless connectivity to an
Ethernet-enabled device such as Internet TV , DVR, Gaming console and so on. Please note
that this port is not allowed to be connected with rout er or AP.
3
TL-WA750RE
150Mbps Universal WiFi Range Extender User Guide
Chapter 2 Hardware Installation
2.1 Before You Begin
Please read this User Guide carefully before ins talling and using the equipment. The operating
distance range of your wireless connection can vary significantly depending on the physical
position of the wireless devices. Factors that can weaken signals by getting in the way of your
network’s radio waves are metal appliances or obst ruct ions , and walls . Typical ranges vary based
on the types of materials and background RF (radio frequency) noise in your home or office.
In order to optimize the performance of TL-WA750RE, please follow the instructions below to
achieve an ideal location (please make sure it is always within the wireless coverage of the
wireless router).
1) Half-way Between - Ge nerally, the ideal locat ion for TL-WA750RE is half-way between the
Wireless router and Wireless Client. If the wireless signal i s not satisfactory, you may place
TL-WA750RE somewhat nearer to the Wireless router.
2) No Obstacles and Spacious - Clear obstacles in the way between TL-WA750RE and
Wireless router. It’s better to locate it in a spac i ous place, such as near the corridors.
3) No Interf erenc e - Keep TL-WA750RE far away from wireless interferenc e, whi ch may come
from electrical appliances that works in the same frequenc y band as TL-WA750RE, such as
Blue tooth devices, cordless phones, mic rowave ovens, etc.
4) 3 Signal Lights - You can also find an ideal location via the signal lights on the front panel of
TL-WA750RE. These lights show the strength of signal your r ange extender receives from
the root AP. It's recommended that you choose a location where at least 3 signal lights light
up, in order to guarantee a good performance.
Note:
TP-LINK recommends that you connect to the Range Extender when your home network
connection is poor, or when you want a larger wireless c overage to eliminate “dead zones ”. As in
compliance with the wireless transmission protocol, all the Range Extender devices are set to
work in half-duplex instead of full-duplex mode. In other words, the Range Extender has to
process one-way communication between your root Wireless router (or AP) and the terminal
clients; so the transmission time will be double -increased, while the speed will be decreased.
4
TL-WA750RE
150Mbps Universal WiFi Range Extender User Guide
2.2 Basic Requirements
Place your Range Extender in a well-ventilated place far from direc t sunlight, any heater or
heating vent.
Leave at least 2 inches (5cm) space around the device for heat dissipation.
Turn off your Range Extender and unplug the power adapter in a lighting storm to avoid
damage.
Use Web browser, such as Microsoft Internet Expl orer 5.0 or above, Net scape Navigator 6. 0
or above.
Operating temperature of the Range Extende r should be 0℃~40℃ (32℉~104℉).
Operating humidity of the Range Extender should be 10%~90% RH (Non-condensing).
2.3 Connecting the Device
Figure 2-1 Typical connection of TL-WA750RE
To establish a typical connection of the Range Extender, please take the following steps:
1. Connect the Cable/DSL modem to a Wireless router with an Ethernet cable.
2. Plug your TL-WA750RE directly to a standard electrical wall socket, which is next to the
Wireless router.
3. Connect your Wireless Clients (such as not ebook, pad, smart phone, etc.) to TL-WA750RE
wirelessly. Or you can connect your PC to the sole LAN port of Range Extender via an
Ethernet cable.
4. Log in the web-based management page of TL-WA750RE and complete the configurations.
(Please refer to Chapter 3 Quick Installation Gui de or Chapter 4 Configure the Device
for the
configurations, as you need.) Through the web page configuration you can successfully
connect TL-WA750RE to the wireless router.
5. Adjust an ideal location for TL-WA750RE. (Please refer to Section 2.1 Before You Beg in for
detailed information about ideal locati on.)
5
TL-WA750RE
150Mbps Universal WiFi Range Extender User Guide
Chapter 3 Quick Installation Guide
This chapter will guide you to configur e your PC to communi cate with the Range E xtender and to
configure and manage the TL-WA750RE 150Mbps Universal WiFi Range Extender easily wi th a
Web-based utility.
With a Web-based utility, it is easy to configure and manage the TL-WA750RE 150Mbps Universal
WiFi Range Extender. The Web-based utili ty can be used on any Windows, Macintosh or UNIX
OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type in the domain name
http://tplinkextender.net in the address field of the browser.
Figure 3-1 Login to the Range Extender
After a moment, a login window will appear as shown i n Figure 3-2. Enter admin for the User
Name and Password (both in lower case letters ). Then cl ick OK or press Enter.
Figure 3-2 Login Windows
Note:
If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go
to Tools menu > In ternet Options > Connections > L AN Settings, in the screen that appears ,
cancel the Using Proxy checkbox, and click OK to finish it.
6
TL-WA750RE
150Mbps Universal WiFi Range Extender User Guide
2. A fter successful login, there will pop up the Quick Setup Start page. Click Next to get the
quick setup started.
Figure 3-3 Quick Setup Start
3. Figure 3-4 will appear for you to choose the region. Then click Next to continue.
Figure 3-4 Quick Setup – Choose Region
4. The devi ce will detect the existing wireless networks. Please wait for a while.
Figure 3-5 Quick Setup – Detect Existing Networks
7
TL-WA750RE
150Mbps Universal WiFi Range Extender User Guide
5. A list of available wireless networks will appear. Check the box before the SSID of your
desired network, and then click Next.
Figure 3-6 Quick Setup – Available Wireless Networks
Note:
If you could not find your wireless network name (SSID) in the list, you can click
redetect it or tick the checkbox before "Set S SID and MAC Manually" to manually configure the
wireless settings.
6. Wireless Settings page will appear as shown in Figure 3-7. Please enter the Wireless
Password of your selected target network and then click Next to continue.
Figure 3-7 Quick Setup – Wireless Settings
Rescan
to
8
Loading...
+ 32 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.