TP Link C20I Users Manual

Archer

C20i

AC750

Wireless

Dual

Band

Router

REV1.0.0

1910011018

Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1） This device may not cause harmful interference.

2） This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

The frequency band of 5150MHz-5250MHz is required indoor users only.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National Restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country Restriction Reason/remark

Bulgaria None

Outdoor use limited to

10 mW e.i.r.p. within

France

the band 2454-2483.5

MHz

Italy None

Luxembourg None

Norway Implemented

Russian Federation None Only for indoor applications

General authorization required for outdoor use and

public service

Military Radiolocation use. Refarming of the 2.4 GHz

band has been ongoing in recent years to allow current

relaxed regulation. Full implementation planned 2012

If used outside of own premises, general authorization is

required

General authorization required for network and service

supply(not for spectrum)

This subsection does not apply for the geographical area

within a radius of 20 km from the centre of Ny-Ålesund

Note: Please don’t use the product outdoors in France.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1)cet appareil ne doit pas provoquer d’interférences et

(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.

Industry Canada Statement

Complies with the Canadian ICES-003 Class B specifications.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice

注意！

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、

加大功率或變更原設計之特性或功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即

停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射

頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響，請妥適使用。

安全諮詢及注意事項

●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

●注意防潮，請勿將水或其他液體潑灑到本產品上。　

●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

z When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

z Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and

voiding the limited warranty. If you need service, please contact us.

z Avoid water and wet locations.

This product can be used in the following countries:

AT BG BY CA CZ DE DK EE

ES FI FR GB GR HU IE IT

LT LV MT NL NO PL PT RO

RU SE SK TR UA

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: AC750 Wireless Dual Band Router

Model No.: Archer C20i

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents

EN 300 328 V1.8.1: 2012

EN 301 489-1 V1.9.2:2011& EN301 489-17 V2.2.1:2012

EN 55022:2010

EN 55024:2010

EN 61000-3-2:2006+A1:2009+A2:2009

EN 61000-3-3:2008

EN 60950-1:2006+A11：2009+A1:2010+A12:2011

EN 50385:2002

EN 301 893 V1.7.1:2012

The product carries the CE Mark:

Person is responsible for making this declaration:

Yang Hongliang Product Manager of International Business

Date of Issue: 2014

TP-LINK TECHNOLOGIES CO., LTD.

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd,

Nanshan, Shenzhen, China

CONTENTS

Package Contents.....................................................................................................1

Chapter 1. Introduction......................................................................................... 2

1.1 Overview of the Router............................................................................................... 2

1.2 Conventions ...............................................................................................................3

1.3 Main Features ............................................................................................................3

1.4 Panel Layout ..............................................................................................................4

1.4.1 The Front Panel.............................................................................................. 4

1.4.2 The Rear Panel ..............................................................................................5

Chapter 2. Connecting the router ........................................................................7

2.1 System Requirements................................................................................................7

2.2 Installation Environment Requirements...................................................................... 7

2.3 Connecting the Router ...............................................................................................7

Chapter 3. Quick Installation Guide.....................................................................9

3.1 TCP/IP Configuration .................................................................................................9

3.2 Quick Installation Guide ........................................................................................... 11

Chapter 4. Configuring the router......................................................................21

4.1 Login ........................................................................................................................21

4.2 Status ....................................................................................................................... 21

4.3 Quick Setup.............................................................................................................. 22

4.4 Network .................................................................................................................... 23

4.4.1 WAN ............................................................................................................. 23

4.4.2 LAN .............................................................................................................. 33

4.4.3 MAC Clone ...................................................................................................34

4.5 Dual Band Selection................................................................................................. 34

4.6 Wireless 2.4GHz ......................................................................................................35

4.6.1 Basic Settings............................................................................................... 35

4.6.2 WPS .............................................................................................................38

4.6.3 Wireless Security.......................................................................................... 40

4.6.4 Wireless MAC Filtering ................................................................................. 44

4.6.5 Wireless Advanced ....................................................................................... 46

4.6.6 Wireless Statistics......................................................................................... 47

4.7 Wireless 5GHz .........................................................................................................48

- I -

4.7.1 Basic Settings............................................................................................... 48

4.7.2 WPS .............................................................................................................50

4.7.3 Wireless Security.......................................................................................... 53

4.7.4 Wireless MAC Filtering ................................................................................. 57

4.7.5 Wireless Advanced ....................................................................................... 59

4.7.6 Wireless Statistics......................................................................................... 60

4.8 Guest Network .........................................................................................................61

4.9 DHCP .......................................................................................................................62

4.9.1 DHCP Settings ............................................................................................. 62

4.9.2 DHCP Clients List.........................................................................................64

4.9.3 Address Reservation ....................................................................................64

4.10 USB Settings............................................................................................................ 66

4.10.1 USB Mass Storage .......................................................................................66

4.10.2 User Accounts ..............................................................................................66

4.10.3 Storage Sharing............................................................................................ 68

4.10.4 FTP Server ................................................................................................... 69

4.10.5 Media Server ................................................................................................ 71

4.10.6 Print Server................................................................................................... 73

4.11 NAT ..........................................................................................................................73

4.12 Forwarding ............................................................................................................... 74

4.12.1 Virtual Servers.............................................................................................. 74

4.12.2 Port Triggering.............................................................................................. 76

4.12.3 DMZ.............................................................................................................. 78

4.12.4 UPnP ............................................................................................................ 78

4.13 Security .................................................................................................................... 79

4.13.1 Basic Security............................................................................................... 79

4.13.2 Advanced Security........................................................................................ 81

4.13.3 Local Management ....................................................................................... 82

4.13.4 Remote Management ................................................................................... 83

4.14 Parent Control.......................................................................................................... 84

4.15 Access Control......................................................................................................... 87

4.15.1 Rule .............................................................................................................. 88

4.15.2 Host .............................................................................................................. 90

4.15.3 Target............................................................................................................ 92

4.15.4 Schedule....................................................................................................... 94

4.16 Advanced Routing.................................................................................................... 95

- II -

4.16.1 Static Route List............................................................................................ 96

4.16.2 System Routing Table................................................................................... 97

4.17 Bandwidth Control.................................................................................................... 98

4.18 IP & MAC Binding..................................................................................................... 99

4.18.1 Binding Settings............................................................................................ 99

4.18.2 ARP List...................................................................................................... 100

4.19 Dynamic DNS.........................................................................................................101

4.19.1 No-ip.com DDNS ........................................................................................ 101

4.19.2 Comexe.cn DDNS ...................................................................................... 102

4.19.3 Dyndns.org DDNS ...................................................................................... 103

4.20 IPv6........................................................................................................................ 104

4.20.1 IPv6 Status .................................................................................................105

4.20.2 IPv6 WAN................................................................................................... 106

4.20.3 IPv6 LAN .................................................................................................... 110

4.21 System Tools...........................................................................................................111

4.21.1 Time Settings...............................................................................................111

4.21.2 Diagnostic................................................................................................... 113

4.21.3 Firmware Upgrade...................................................................................... 114

4.21.4 Factory Defaults ......................................................................................... 115

4.21.5 Backup & Restore....................................................................................... 116

4.21.6 Reboot........................................................................................................ 117

4.21.7 Password.................................................................................................... 117

4.21.8 System Log................................................................................................. 118

4.21.9 Statistics ..................................................................................................... 118

4.22 Logout .................................................................................................................... 121

Appendix A: FAQ ..................................................................................................122

Appendix B: Configuring the PC.........................................................................127

Appendix C: Specifications .................................................................................129

Appendix D: Glossary .......................................................................................... 130

- III -

Archer C20i AC750 Wireless Dual Band Router

Package Contents

The following items should be found in your package:

¾ Archer C20i AC750 Wireless Dual Band Router

¾ DC Power Adapter for Archer C20i AC750 Wireless Dual Band Router

¾ Quick Installation Guide

¾ Resource CD for Archer C20i AC750 Wireless Dual Band Router, including:

• This Guide

• Other Helpful Information

Note:

)

Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor.

- 1 -

Archer C20i AC750 Wireless Dual Band Router

Chapter 1. Introduction

1.1 Overview of the Router

The Archer C20i AC750 Wireless Dual Band Router integrates 4-port Switch, Firewall, NAT-router and Wireless AP. The AC750 Wireless Dual Band Router delivers exceptional range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks and the users demanding higher networking performance. Your wireless connections are radio band selectable to avoid interference in your area, and the four built-in Gigabit ports supply high-speed connection to your wired devices.

The Archer C20i AC750 Wireless Dual Band Router provides up to 750Mbps wireless connection with other wireless clients. The incredible speed makes it ideal for handling multiple data streams at the same time, which ensures your network stable and smooth. The performance of this 802.11ac wireless router will give you the unexpected networking experience at speed much faster than

802.11n. It is also compatible with all IEEE 802.11n, IEEE 802.11a, IEEE 802.11b and IEEE 802.11g products.

Multiple Security Protections

With multiple protection measures, including SSID broadcast control and wireless LAN 64/128-bit WEP encryption, Wi-Fi Protected Access (WPA2- PSK, WPA- PSK), as well as advanced Firewall protections, the Archer C20i AC750 Wireless Dual Band Router provides complete data privacy.

The Archer C20i AC750 Wireless Dual Band Router provides flexible access control, so that parents or network administrators can establish restricted access policies for children or staff. It also supports Virtual Server and DMZ host for Port Triggering, and then the network administrators can manage and monitor the network in real time with the remote management function.

Incredible Speed

Flexible Access Control

Simple Installation

Since the router is compatible with virtually all the major operating systems, it is very easy to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in this user guide. Before installing the router, please look through this guide to know all the router’s functions.

- 2 -

Archer C20i AC750 Wireless Dual Band Router

1.2 Conventions

The router or Archer C20i mentioned in this guide stands for Archer C20i AC750 Wireless Dual Band Router without any explanation.

1.3 Main Features

¾ Complies with IEEE 802.11ac.

¾ One 10/100M Auto-Negotiation RJ45 Internet port, four 10/100M Auto-Negotiation RJ45

Ethernet ports, supporting Auto MDI/MDIX.

¾ Provides one USB port supporting storage/FTP/Media/Print Server.

¾ Provides WPA/WPA2, WPA-PSK/WPA2-PSK authentication, TKIP/AES encryption security.

¾ Shares data and Internet access for users, supporting Dynamic IP/ Static IP/ PPPoE/ PPTP/

L2TP/ BigPond Internet access.

¾ Supports simultaneous 2.4GHz and 5GHz connections for 750Mbps of total available

bandwidth.

¾ Supports Virtual Server, Special Application and DMZ host.

¾ Supports UPnP, Dynamic DNS, Static Routing.

¾ Provides Automatic-connection and Scheduled Connection on certain time to the Internet.

¾ Built-in NAT and DHCP server supporting static IP address distributing.

¾ Supports Parent Control and Access Control.

¾ Connects Internet on demand and disconnects from the Internet when idle for PPPoE.

¾ Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).

¾ Supports Flow Statistics.

¾ Supports IPv6.

¾ Supports firmware upgrade and Web management.

- 3 -

Archer

C20i

AC7

50Wireless

Dual

Band

Router

1.4

Panel

Lay

out

1.4.1

The

Front

Panel

Figure

1-1

LEDs

thefr

ontpanel

The

router’s

LEDs

are

located

the

front

anel(V

iew

from

lefttoright).

Name

Status

Indication

(Power)

(Wireless)

Power

on.

2.4GHz

5GHz

both

radio

bands.

The

storage

device

hasbeen

successfully

recogni

ed.

-4-

(Ethernet)

(Internet)

Off Power is off.

Off The wireless function is disabled.

The wireless function is enabled. The router is working on

Off No device is connected to the Ethernet ports.

On At least one device has connected to the Ethernet ports.

Off The Internet connection is not available.

Off No storage device or printer is plugged into the USB port.

The network is available with a successful Internet connection.

(USB)

Flashing A plugged-in storage device or printer is being recognized.

Archer

C20i

AC7

50Wireless

Dual

Band

Router

1.4

Panel

Lay

out

1.4.1

The

Front

Panel

Figure

1-1

LEDs

thefr

ontpanel

The

router’s

LEDs

are

located

the

front

anel(V

iew

from

lefttoright).

Name

Status

Indication

(Power)

(Wireless)

Power

on.

2.4GHz

5GHz

both

radio

bands.

The

storage

device

hasbeen

successfully

recogni

ed.

-4-

(Ethernet)

(Internet)

Off Power is off.

Off The wireless function is disabled.

The wireless function is enabled. The router is working on

Off No device is connected to the Ethernet ports.

On At least one device has connected to the Ethernet ports.

Off The Internet connection is not available.

Off No storage device or printer is plugged into the USB port.

The network is available with a successful Internet connection.

(USB)

Flashing A plugged-in storage device or printer is being recognized.

Archer C20i AC750 Wireless Dual Band Router

¾ USB: The USB port connects to a USB storage device or a USB printer.

¾ WPS/Reset:

Pressing this button for less than 5 seconds enables the WPS function. If your client devices, such as wireless adapters, support Wi-Fi Protected Setup, press this button to quickly establish a WPA secure connection between the client devices and the router.

Pressing this button for more than 5 seconds enables the Reset function. With the router powered on, press and hold the WPS/Reset button (approximately 8 seconds) until all LEDs are lit. And then release the button and wait for the router to reboot to its factory default settings.

¾ Wireless On/Off: The button for the wireless function.

¾ On/Off: The switch for the power.

- 6 -

Archer C20i AC750 Wireless Dual Band Router

Chapter 2. Connecting the router

2.1 System Requirements

¾ Broadband Internet Access Service (DSL/Cable/Ethernet)

¾ One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the router is

connected directly to the Ethernet)

¾ PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors

¾ TCP/IP protocol on each PC

¾ Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari

2.2 Installation Environment Requirements

¾ Place the router in a well-ventilated place far from any heater or heating vent

¾ Avoid direct irradiation of any strong light (such as sunlight)

¾ Keep at least 2 inches (5 cm) of clear space around the router

¾ Operating Temperature: 0℃~40℃ (32℉~104℉)

¾ Operating Humidity: 10%~90%RH, Non-condensing

2.3 Connecting the Router

Before installing the router, make sure your PC is connected to the Internet through the broadband service successfully. If there is any problem, please contact your ISP. After that, please install the router according to the following steps. Don't forget to pull out the power plug and keep your hands dry.

1. Power off your modem (if the modem has a backup battery, please remove it too.), and disconnect your existing router if you have one.

2. Connect the Internet port on your router to the modem’s LAN port with an Ethernet cable.

3. Connect your computer to one of the Ethernet ports labeled 1~4 on the router with an Ethernet cable.

4. Power on the modem and wait for 2 minutes.

5. Then plug the provided power adapter into the Power jack and the other end to a standard electrical wall socket. Press the Power On/Off button to power on the router. (Before you

- 7 -

Archer C20i AC750 Wireless Dual Band Router

power on the router, please make sure your computer is NOT connected to any other wireless network.)

Figure 2-1 Hardware Installation

Figure 2-2 USB Installation

Note:

)

If you want to use the router to share files or printer, plug the USB storage device to the USB port or connect the printer to the router with a matching cable.

- 8 -

Archer C20i AC750 Wireless Dual Band Router

Chapter 3. Quick Installation Guide

This chapter will show you how to configure the basic functions of your Archer C20i AC750 Wireless Dual Band Router using Quick Setup Wizard within minutes.

3.1 TCP/IP Configuration

The default IP address of the router is 192.168.0.1 and the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description.

Connect the local PC to the Ethernet ports of the router and then you can configure the IP address for your PC by the following method: Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to

Appendix B: Configuring the PC

Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the router. The following example is in Windows XP OS.

Open a command prompt, and type ping 192.168.0.1, and then press Enter.

¾ If the result displayed is similar to the Figure 3-1, it means the connection between your PC

and the router has been established well.

. Then the built-in DHCP server will assign IP address for the PC.

Figure 3-1 Success result of Ping command

- 9 -

Archer C20i AC750 Wireless Dual Band Router

¾ If the result displayed is similar to Figure 3-2, it means the connection between your PC and

the router failed.

Figure 3-2 Failure result of Ping command

Please check the connection following these steps:

1. Is the connection between your PC and the router correct?

Note:

)

The Ethernet LED on the router and LEDs on your PC's adapter should be lit.

2. Is the TCP/IP configuration for your PC correct?

)

If the router's IP address is 192.168.0.1, your PC's IP address must be within the range of

192.168.0.2 ~ 192.168.0.254.

3. Is the default LAN IP of the router correct?

Note:

) Note:

If the LAN IP of the modem connected with your router is 192.168.0.x, the default LAN IP of the router will automatically switch from 192.168.0.1 to 192.168.1.1 to avoid IP conflict. Therefore, in order to verify the network connection between your PC and the router, you can open a command prompt, and type ping 192.168.1.1, and then press Enter.

- 10 -

Archer C20i AC750 Wireless Dual Band Router

3.2 Quick Installation Guide

With a Web-based utility, it is easy to configure and manage the Archer C20i AC750 Wireless Dual Band Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.

1. To access the configuration utility, open a web-browser and type in the default IP address

http://tplinklogin.net

in the address field.

Figure 3-3 Log in the router

After a moment, a login window will appear, similar to Figure 3-4. Enter admin for the User Name and Password, both in lower case letters. Then click the Login button or press the Enter key.

Figure 3-4 Login Windows

Note:

)

If the above screen does not pop up, it means that your Web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.

2. After successful login, the Quick Setup page will appear for you to quickly configure your router.

- 11 -

Archer C20i AC750 Wireless Dual Band Router

Figure 3-5 Quick Setup

3. Click Next, and then WAN Connection Type page will appear, shown in Figure 3-6.

Figure 3-6 WAN Connection Type

The router provides Auto-Detect function and supports five types of WAN connection: Dynamic IP,

Static IP, PPPoE/Russian PPPoE, L2TP/Russian L2TP, and PPTP/Russian PPTP. It’s

recommended that you make use of the Auto-Detect function. If you are sure of what kind of

connection type your ISP provides, you can select the very type and click Next to go on configuring.

4. If you select Auto-Detect, the router will automatically detect the connection type your ISP provides. Make sure the cable is securely plugged into the Internet port before detection. The appropriate configuration page will be displayed when an active Internet service is successfully detected by the router.

Note:

)

If Auto-Detect fails, you can select the connection type your ISP provides in Figure 3-6, and follow the configuring procedures below to continue.

1) If the connection type detected is Dynamic IP, there will appear the MAC Clone page (as

shown in Figure 3-7). In most cases, there is no need to clone the MAC address. You can

- 12 -

Archer C20i AC750 Wireless Dual Band Router

select “No, I do NOT need to clone MAC address” and then click Next. If it is necessary in your case, please select “Yes, I need to clone MAC address” and then click Next.

Figure 3-7 Quick Setup – MAC Clone

2) If the connection type detected is Static IP, the next screen will appear as shown in

Figure 3-8. Configure the following parameters and then click Next to continue.

Figure 3-8 Quick Setup - Static IP

¾ IP Address - This is the WAN IP address as seen by external users on the Internet

(including your ISP). Your ISP will provide you with the IP address you need to enter here. Enter the IP address into the field.

¾ Subnet Mask - The Subnet Mask is used for the WAN IP address. Your IPS will provide

you with the subnet mask which is usually 255.255.255.0.

¾ Gateway - Your ISP will provide you with the Gateway address which is the ISP server’s

address. Enter the gateway IP address into the box if required.

¾ DNS Server - （Optional）Enter the DNS Server IP address into the box if required.

¾ Secondary DNS Server-（Optional） If your ISP provides another DNS server, enter it

into this field.

- 13 -

Archer C20i AC750 Wireless Dual Band Router

3) If the connection type detected is PPPoE/Russia PPPoE, the next screen will appear as

shown in Figure 3-9. Configure the following parameters and then click Next to continue.

Figure 3-9 Quick Setup – PPPoE/Russia PPPoE

¾ Username/Password - Enter the Username and Password provided by your ISP.

These fields are case-sensitive. If you have difficulty with this process, please contact your ISP.

¾ Confirm password - Enter the password again to make sure that the password is

correct.

4) If your connection type is L2TP/ Russia L2TP, select L2TP/Russia L2TP in Figure 3-6

and the next screen will appear as shown in Figure 3-10.Configure the following parameters and then click Next to continue.

Figure 3-10 Quick Setup – L2TP/Russia L2TP

¾ Username/Password - Enter the Username and Password provided by your ISP.

These fields are case-sensitive. If you have difficulty with this process, please contact your ISP.

Select Static IP if the IP Address/ Subnet Mask/ Gateway and DNS server address have been provided by your ISP. Then please enter server IP address or domain name provided by your ISP, and also enter the corresponding parameters.

- 14 -

Archer C20i AC750 Wireless Dual Band Router

Select Dynamic IP if none of the above parameters are provided. Then you just need to enter server IP address or domain name provided by your ISP.

5) If your connection type is PPTP/Russia PPTP, select PPTP/Russia PPTP in Figure 3-6

and the next screen will appear as shown in Figure 3-11. Configure the following parameters and then click Next to continue.

Figure 3-11 Quick Setup – PPTP/Russia PPTP

¾ Username/Password - Enter the Username and Password provided by your ISP.

These fields are case-sensitive. If you have difficulty with this process, please contact your ISP.

- 15 -

Archer C20i AC750 Wireless Dual Band Router

Select Dynamic IP if none of the above parameters are provided. Then you just need to enter server IP address or domain name provided by your ISP.

5. After finishing the WAN Connection Type selection, the Wireless Dual Band Selection page will appear as shown in Figure 3-12. Choose the frequency you want for your wireless network and then click Next.

Figure 3-12 Quick Setup – Dual Band Selection

¾ 2.4GHz - You can use the 2.4GHz band to connect to many classic wireless devices like

gaming consoles, laptops, DVRs, etc.

¾ 5GHz - This band is less crowded and is used for time-sensitive music, video streaming

or gaming. Using this band can avoid interference with 2.4GHz networks or noisy devices like cordless phones and microwave ovens.

6. Configure the basic parameters for 2.4GHz wireless network in the following screen as shown in Figure 3-13, and then click Next.

- 16 -

Archer C20i AC750 Wireless Dual Band Router

Figure 3-13 Quick Setup – Wireless 2.4GHz

¾ Wireless Network Name - Also called the SSID (Service Set Identification). Enter a

value of up to 32 characters. The same name must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_2.4GHz_XXXXXX. This value is case-sensitive. For example, TEST is NOT the same as test.

¾ Region - Select your region from the drop-down list. This field specifies the region

where the wireless function of the router can be used. It may be illegal to use the wireless function of the router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.

Note:

)

Limited by local law regulations, version for North America does not have region selection option.

¾ Security

z Enable Security (WPA-PSK/WPA2-PSK) – It’s selected by default, with the

default PSK password the same as the default PIN code.

z Disable Wireless Security - The wireless security function can be enabled or

disabled. If disabled, the wireless stations will be able to connect the router without encryption.

The above settings are only for basic wireless parameters. For advanced settings, please check “More Advanced Wireless Settings”, and then you can set the following parameters.

- 17 -

Archer C20i AC750 Wireless Dual Band Router

¾ Band - This field displayed the operating frequency being configured.

¾ Mode - This field determines the wireless mode which the router works on.

z 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.

z 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless

clients.

¾ Channel Width - Select any channel width from the drop-down list. The default setting

is “Auto”, which can adjust the channel width for your clients automatically.

¾ Channel - This field determines which operating frequency will be used. It is not

necessary to change the wireless channel unless you notice interference problems with another nearby access point. If you select “Auto”, then the AP will select the best channel automatically.

7. Configure the basic parameters for 5GHz wireless network in the following screen as shown in Figure 3-14, and then click Next.

Figure 3-14 Quick Setup – Wireless 5GHz

¾ Wireless Network Name - Also called the SSID (Service Set Identification). Enter a

value of up to 32 characters. The same name must be assigned to all wireless devices

- 18 -

Archer C20i AC750 Wireless Dual Band Router

in your network. The default SSID is set to be TP-LINK_5GHz_XXXXXX. This value is case-sensitive. For example, TEST is NOT the same as test.

¾ Region - Select your region from the drop-down list. This field specifies the region

Note:

)

Limited by local law regulations, version for North America does not have region selection option.

¾ Security

z Enable Security (WPA-PSK/WPA2-PSK) – It’s selected by default, with the

z Disable Security - The wireless security function can be enabled or disabled. If

default PSK password the same as the default PIN code.

disabled, the wireless stations will be able to connect the router without encryption.

The above settings are only for basic wireless parameters. For advanced settings, please check “More Advanced Wireless Settings”, and then you can set the following parameters.

¾ Band - This field displayed the operating frequency being configured.

¾ Mode - This field determines the wireless mode which the router works on.

z 11an mixed - Select if you are using both 802.11a and 802.11n wireless clients.

z 11a/n/ac mixed – Select if you are using 802.11a, 802.11n and 802.11ac wireless

clients.

¾ Channel Width - Select any channel width from the drop-down list. The default setting

is “Auto”, which can adjust the channel width for your clients automatically.

¾ Channel - This field determines which operating frequency will be used. It is not

necessary to change the wireless channel unless you notice interference problems with another nearby access point. If you select “Auto”, then the AP will select the best channel automatically.

8. Confirm the parameters and click the Save button to make the settings take effect.

- 19 -

Archer C20i AC750 Wireless Dual Band Router

Figure 3-15 Quick Setup - Confirm

9. Click the Finish button to complete the Quick Setup.

Figure 3-16 Quick Setup - Finish

- 20 -

+ 111 hidden pages