TP-Link AC750 User Manual

RE200

AC750 WiFi Range Extender

REV1.0.0

1910011070

Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National Restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country Restriction Reason/remark

Bulgaria None

Outdoor use limited to

France

Italy None

Luxembourg None

Norway Implemented

Russian Federation None Only for indoor applications

Note: Please don’t use the product outdoors in France.

10 mW e.i.r.p. within the band 2454-2483.5 MHz

General authorization required for outdoor use and

public service

Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

If used outside of own premises, general authorization is required

General authorization required for network and service supply(not for spectrum)

This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired

operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le

fonctionnement est soumis aux deux conditions suivantes: (1)cet appareil ne doit pas provoquer d’interférences et (2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un

fonctionnement non souhaité de l’appareil.

Industry Canada Statement

Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice

注意！

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響，請妥適使用。

於 5.25GHz 至 5.35GHz 區域內操作之無線設備的警告聲明

工作頻率 5.250~5.350GHz 該頻段限於室內使用。

安全諮詢及注意事項

●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

●注意防潮，請勿將水或其他液體潑灑到本產品上。 

●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

z When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

z Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock

and voiding the limited warranty. If you need service, please contact us.

z Avoid water and wet locations.

This product can be used in the following countries:

AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SK TR UA US

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: AC750 WiFi Range Extender

Model No.: RE200

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents

ETSI EN 300 328 V1.7.1: 2006

ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.2.1:2012

EN 55022:2010

EN 55024:2010

EN 61000-3-2:2006+A1:2009+A2:2009

EN 61000-3-3:2008

EN 60950-1:2006+A11：2009+A1:2010+A12:2011

EN 62311:2008

The product carries the CE Mark:

Person responsible for making this declaration:

Yang Hongliang

Product Manager of International Business

Date of issue: 2014

TP-LINK TECHNOLOGIES CO., LTD.

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,

Shennan Rd, Nanshan, Shenzhen, China

CONTENTS

Package Contents .................................................................................................... 1

Chapter 1 Introduction........................................................................................... 2

1.1 Product Overview.............................................................................................. 2

1.2 Main Features ................................................................................................... 2

1.3 Appearance....................................................................................................... 2

Chapter 2 Hardware Installation ........................................................................... 4

2.1 Before You Begin.............................................................................................. 4

2.2 Basic Requirements.......................................................................................... 4

2.3 Connecting the Device...................................................................................... 5

Chapter 3 Quick Installation Guide....................................................................... 6

Chapter 4 Configure the Device.......................................................................... 12

4.1 Status.............................................................................................................. 12

4.2 Quick Setup .................................................................................................... 14

4.3 Network........................................................................................................... 14

4.3.1 LAN..................................................................................................................15

4.3.2 DHCP Settings.................................................................................................16

4.3.3 DHCP Client List.............................................................................................. 18

4.4 Wireless .......................................................................................................... 18

4.4.1 Connect To Existing Network ..........................................................................19

4.4.2 Extender Settings ............................................................................................19

4.4.3 Advanced Settings........................................................................................... 20

4.4.4 High Speed...................................................................................................... 21

4.4.5 Wireless Statistics............................................................................................21

4.5 LED On/Off ..................................................................................................... 22

4.6 System Tools .................................................................................................. 22

4.6.1 Firmware Upgrade...........................................................................................23

4.6.2 Factory Defaults...............................................................................................24

4.6.3 Backup & Restore............................................................................................24

4.6.4 Reboot .............................................................................................................25

4.6.5 Password......................................................................................................... 25

4.6.6 System Log...................................................................................................... 26

Appendix A: Factory Defaults ............................................................................... 27

Appendix B: Troubleshooting............................................................................... 28

Appendix C: Specifications................................................................................... 30

Appendix D: Glossary............................................................................................ 31

RE200 AC750 WiFi Range Extender User Guide

Package Contents

The following items should be found in your package:

¾ RE200 AC750 WiFi Range Extender

¾ Ethernet Cable

¾ Quick Installation Guide

¾ Resource CD for RE200 AC750 WiFi Range Extender, including:

z This User Guide

Note:

)

Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact your distributor.

Conventions

The Range Extender, the Device or RE200 mentioned in this User guide stands for RE200 AC750 WiFi Range Extender without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand.

The power plug may differ from the picture illustrated in this UG due to different regional power specifications. As follows we just take that of EU version for example.

RE200 AC750 WiFi Range Extender User Guide

Chapter 1 Introduction

1.1 Product Overview

The RE200 AC750 WiFi Range Extender is dedicated to Small Office/Home Office (SOHO) wireless network solutions. It will enlarge your existing wireless network and mobility within your wireless network while also allowing you to connect a wired device to a wireless environment. Increased mobility and the absence of cabling will be beneficial for your network.

With using IEEE 802.11ac wireless technology, this device can transmit wireless data at the rate of up to 300Mbps (2.4GHz) + 433Mbps (5GHz). With multiple protection measures, including wireless LAN 64/128/152-bit WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), the RE200 AC750 WiFi Range Extender delivers complete data privacy. It is also compatible with all IEEE 802.11n, IEEE 802.11a, IEEE 802.11b and IEEE 802.11g products.

It supports an easy wireless connection to the root Router/AP (equipped with WPS/QSS button) by pressing the WPS button on the front panel. It also supports an easy, web-based setup for installation and management. Even though you may not be familiar with the Range Extender, you can easily configure it with the help of this Guide. Before installing the Range Extender, please look through this Guide to get the full information of the RE200 AC750 WiFi Range Extender.

1.2 Main Features

¾ Complies with IEEE 802.11ac ¾ Provides multiple encryption security Types including: 64/128/152-bit WEP and

WPA-PSK/WPA2-PSK

¾ Supports Built-in DHCP server ¾ Supports Firmware Upgrade ¾ Supports Web-based Management

1.3 Appearance

Figure 1-1

RE200 AC750 WiFi Range Extender User Guide

z LED Explanation:

Name Status Indication

5G/2.4G

Wireless Signal

ETHERNET

Power

Solid Green

The Range Extender is connected to the 5G/2.4G wireless network of your main Router/AP, and the signal strength is strong.

Solid Red

The Range Extender is connected to the 5G/2.4G wireless network of your main Router/AP, but the signal strength is weak.

Off

Flashing

Off

The Range Extender isn’t connected to your main Router/AP.

The Range Extender’s wireless function is enabled.

The Range Extender’s wireless function is disabled. A device is connected to the ETHERNET port, but there is no

activity.

A device is connected to the ETHERNET port, and is active.

No device is connected to the ETHERNET port.

The Range Extender is on.

The Range Extender is off.

The Range Extender has established a secure connection.

Flashing The Range Extender is establishing a secure connection.

Off No active connection.

Table 1-1

(RANGE EXTENDER/WPS): If your Wireless router or AP supports WPS or QSS function, you can press the WPS or QSS button and then press the RANGE EXTENDER button to establish a secure connection between the Wireless router or AP and the Range Extender RE200.

z RESET: This button is used to restore the Range Extender’s factory default settings.

There are two ways to reset the Range Extender’s factory defaults:

Method One: With the Range Extender powered on, use a pin to press RESET button (about 1 seconds) until all the LEDs flash once. And then release the button and wait the Range Extender to reboot to its factory default settings.

Method Two: Restore the default settings from “System Tools > Factory Defaults” of the Range Extender's Web-based Management page.

z ETHERNET: One 10/100Mbps RJ45 Ethernet port used to add wireless connectivity to an

Ethernet-enabled device such as Internet TV, DVR, Gaming console and so on. Please note that this port is not allowed to be connected with router or AP.

RE200 AC750 WiFi Range Extender User Guide

Chapter 2 Hardware Installation

2.1 Before You Begin

Please read this User Guide carefully before installing and using the equipment. The operating distance range of your wireless connection can vary significantly depending on the physical position of the wireless devices. Factors that can weaken signals by getting in the way of your network’s radio waves are metal appliances or obstructions, and walls. Typical ranges vary based on the types of materials and background RF (radio frequency) noise in your home or office.

In order to optimize the performance of RE200, please follow the instructions below to achieve an ideal location (please make sure it is always within the wireless coverage of the wireless router).

1) Half-way Between - Generally, the ideal location for RE200 is half-way between the Wireless router and Wireless Client. If the wireless signal is not satisfactory, you may place RE200 somewhat nearer to the Wireless router.

2) No Obstacles and Spacious - Clear obstacles in the way between RE200 and Wireless router. It’s better to locate it in a spacious place, such as near the corridors.

3) No Interference - Keep RE200 far away from wireless interference, which may come from electrical appliances that works in the same frequency band as RE200, such as Blue tooth devices, cordless phones, microwave ovens, etc.

Note:

)

TP-LINK recommends that you connect to the Range Extender when your home network connection is poor, or when you want a larger wireless coverage to eliminate “dead zones”. As in compliance with the wireless transmission protocol, all the Range Extender devices are set to work in half-duplex instead of full-duplex mode. In other words, the Range Extender has to process one-way communication between your root Wireless Router or AP and the terminal clients; so the transmission time will be double-increased, while the speed will be decreased.

2.2 Basic Requirements

z Place your Range Extender in a well-ventilated place far from direct sunlight, any heater or

heating vent.

z Leave at least 2 inches (5cm) space around the device for heat dissipation. z Turn off your Range Extender and unplug the power adapter in a lighting storm to avoid

damage.

+ 28 hidden pages