1200 North Main St.
Fostoria, OH 44830
Phone: 800-495-4525
Fax: 419-435-0842
www.tpicorp.com
SELF-CONTAINED POWER MISTER
MODELS: PM-18FO, PM-18S, PM-18C
PM-18FO
IMPORTANT SAFETY
INFORMATION INSIDE
• Serious injury or death possible.
• Read, understand, and follow all
safety information and
instructions in this manual before
using or servicing this product.
• Retain these instructions for
future reference.
PM-18S
Specifications Pages 2,3
PM-18C Assembly Pages 3,4
Set-up / Operation Pages 5,6
Replacement parts
Maintenance
Warranty Page 8
If y ou h av e qu estions a bout the
pro duct you have purchased o r wo uld
like to lea ve us fee dback please
contact us v ia our we bsite
ww w.fo storiaindustries.co m
or by calling 1-800 -495-4525.
PM-18C
CONTENTS
Page 7
Page 8
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 1 of 8
SPECIFICATIONS
PM-18FO
coated
guard mounted on a yoke attached to the pump
An integral ground fault circuit interrupter (GFCI)
Shipped in a single carton and ready to assemble to
THANK YOU!!
contained power misting equipment for your comfort
e components and materials available
The cool air you will now enjoy when using this misting equipment is created through the process of evaporation.
contained power
misting equipment creates a “fog” by pumping water at a very low flow rate through small nozzles. When
evaporated. The heat required to evaporate the fog is
extracted from the air causing a reduced air temperature. This cooler air is then distributed to people or animals
ected by local conditions. For best results, it may be
necessary to experiment with the number of nozzles operating to achieve the cooling performance you desire.
Water supply
POR
TABLE ONLY
Thank you very much for selecting TPI Corporation’s selfconditioning needs. These products were engineered with the most reliabl
and are equipped with features to assure ease of mobility, use, and maintenance.
Heat is required to change water from a liquid to a gas or “water vapor”. TPI Corporation’s self-
combined with the air added by a fan, this fog is rapidly
creating a direct cooling effect.
The performance of your misting system can be aff
Thank you again and stay cool!
TPI Corporation’s self-contained power misting equipment is configured into three separate models:
An 18-inch fan head and pump enclosure. Model no. PM-18FO
An 18 inch fan head, pump enclosure, and 10 gallon cooler. Model no. PM-18S
An 18-inch fan head, pump enclosure, 10 gallon cooler and cart. Model no. PM-18C
All Models
Voltage (VAC) 120
Frequency (Hz) 60
Total Amps 2.2
Pump output 2 gph @ 130psi
Misting hub 4 nozzles installed
Filter 50 mesh stainless steel
Voltage (VAC) 120
Frequency (Hz) 60
Amps 1.5
HP 1/8
CFM 5750
Speeds 1
Fan Specifications
MODEL:
• One 18-inch fan head with white powder-
enclosure.
•
is attached to the power cord.
• Equipped with a power cutoff tip switch.
• One extra nozzle and two plugs included.
•
your existing 10-gallon Igloo cooler.
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 2 of 8
SPECIFICATIONS (continued)
PM
-
18C CART ASSEMBLY & PARTS LIST
PM-18S
coated
nted on a yoke attached to the pump
An integral ground fault circuit interrupter (GFCI) is
as water
PM-18C
coated guard
inch wheels and
a tray. (Customer assembly of these components is
An integral ground fault circuit interrupter (GFCI) is
gallon Igloo cooler is included for use as water
ITEM
NO.
10
11
12
13
14
15
16
17
1
2
3
4
5
6
7
8
9
DESCRIPTION
Mast
Washer Flat 1/4
Hex Nut 1/4-20
Bolt Carriage 1/4-20 x 1-3/4”
Base
Base Tray
Push Nut
Washer Curved
Wheel 10”
Handle Grip
Screw Hex Head 1/2-13 x 1
Washer Lock 1/2”
Screw HWH 8-32 x 3/8
Yoke
Retaining strap
Nozzle (Brass)
Plug
MODEL:
• One 18-inch fan head with white powderguard mou
enclosure.
•
attached to the power cord.
• Equipped with a power cutoff tip switch.
• One extra nozzle and two plugs included.
• A 10-gallon Igloo cooler is included for use
reservoir.
• Shipped in two cartons and ready to assemble.
MODEL:
• One 18-inch fan head with white powdermounted on a yoke that attaches to the cart mast.
• The cart base is supplied with two 10-
required. See assembly instructions on page 4.)
•
attached to the power cord.
• Equipped with a power cutoff tip switch.
• One extra nozzle and two plugs included.
• A 10-
reservoir.
• Shipped in a single carton and ready to assemble.
PART NO.
8045700
35042001
3442532
3440132
3409456
8499700
3504121
3448056
8483100
3409100
2474400
3419500
2326500
3314721
44134001
44108001
44108002
QTY.
1
8
8
8
1
1
2
2
2
1
1
1
1
1
1
5
2
11
12
14
16
17
13
1
Fan yoke / Mast assembly
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 3 of 8
TOOLS REQUIRED: Screwdriver, adjustable wrench,
surface with legs
downward as shown above. Install wheels onto axle;
making sure the hub extension is facing inward
nut (item 7)
on axle and using a hammer, seat in place with a
tall tray (item 6) on base using four carriage bolts
(item 4), and four each of washers and nuts (items 2
tighten only.
Adjustment may be necessary when securing mast to
se
Place Igloo cooler inside retaining ring on tray with
Place pump enclosure on cooler. Make sure intake
Attach fan yoke (item 14) to top of mast (item 1)
13 x 1” screw (item 11) and 1/2” lock
32 x 3/8”
mast.
yoke
PM
-
18C CART ASSEMBLY
(continued)
4
6
5
hammer, and pliers.
1. Place base (item 5) on flat work
toward the base. Next place one push-
sharp blow. Repeat for other wheel.
2. Ins
& 3) as shown. NOTE: Finger-
tray.
3. Install mast (item 1) by bolting mast to tray and ba
assembly as shown above. Now tighten all bolts.
4.
spout toward front.
5. Secure cooler to mast with retaining strap (item 15).
6.
line and filter are in bottom of cooler.
7.
using 1/2washer (item 12). (See illustration on page 3.)
8. Position fan yoke as shown and install 8screw (item 13) through yoke and into hole in
Tighten securely. (See illustration on page 3.)
3
7
4
1
10
2
2
9
4
3
Hub
extension
2
3
Pump
enclosure
Intake line
Filter
Retaining
strap
Cooler
Spout
Retaining ring
Fan
Attach retaining strap s-hooks
to bracket on mast.
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 4 of 8
•
will form on those surfaces. Redirect the fan to prevent this circumstance.
SET
-
UP / OPERATION
Always operate the Power Mister on a level
it is tipped over or tilted
over switch
will shut off power to the pump and fan. Power
will be restored when unit is placed in the upright
Fill cooler with clean fresh water (ice may be
is used. Drain unused
Aim mister downwind for best results. If more than
one mister is used, arrange them in an arc around
To energize, plug the GFCI safety plug into any
Test GFCI per
position
switch located on the top of the pump case. Turn to
either “Fan” (for air movement only) or “Fan /
The misting hub located in the center of the fan is
nozzles. The output volume of
water vapor can be reduced by replacing one or
The unit will mist for approximately 5 hours on 10
GFCI SAFETY PLUG TEST
The GFCI plug mentioned above provides protection
from electric shock by examining the product’s electrical
circuit for current leakage. It must be tested before each
the indicator will show if power is
Do not carry unit by the motor,
1.
surface. In the event the un
more than 35 degrees, a built-in tip-
position.
2.
added) each time mister
water at the end of use period.
3.
the area to be misted.
4.
120 VAC 60 Hz grounded outlet.
instructions below. Turn on the two-
Pump” (for air and mist).
5.
equipped with four
two of the nozzles with the plugs provided.
6.
gallons of water.
use to assure safe operation. Test as described below:
1. Plug into outlet –
available.
2. Press the test button – indicator will turn off.
3. Press reset button. Use product only if GFCI resets.
Do not use if above test fails.
ELECTRICAL SHOCK
HAZARD
PINCH HAZARD
TRIP HAZARD
• Serious injury or death may
occur.
• Only plug these models into
properly grounded receptacles.
• Disconnect from electric
supply before filling, servicing,
or moving this equipment.
• Test GFCI before using. See
instructions at left.
•
electric cords, hose line, fan
guard or support bars.
• Do not touch fan motor during
use or directly after, it may be
hot.
• Do not operate fans without
guards in place.
• Do not insert anything into fan
guard while operating.
• Unplug unit and dry wet areas
before resetting unit that has
been tipped over.
• Position all electric cords to lie
flat on ground or floor.
• Never use during rain, sleet,
hail, snow or any other
inclement weather conditions.
Never operate pump without water supply.
• Check for leaks. If there are any, turn pump off and hand tighten leaky fittings.
• Excessively hard (hi-solids) water can plug nozzles.
• A plugged filter caused by poor quality water can restrict flow to pump causing permanent damage.
•
Never allow the “fog” from the nozzles to come in contact with surfaces. This will cause condensation and water
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 5 of 8
SET
-
UP / OPERATION
(continued)
Take empty cooler to the approximate location to be
misted. Carrying a full cooler will be difficult to do
Place the fan / pump enclosure on the Igloo cooler
ne and filter are in bottom of
18FO comes without a cooler. Since the
gallon
Igloo cooler, it must be used only with a similar Igloo
DO NOT USE THE
ER WATER
EFORE MOVING
Water in cooler will add extra
prox. 80 lbs.) and is likely to spill out when
cart is tilted back and will make the cart unstable and
NOTE
Hanging Slot
Hanging Tab
Fan / pump
enclosure
Intake line
Filter
10-gallon
Igloo cooler
To prepare models PM-18S and PM-18FO for operation:
1.
since it will weigh approximately 80-pounds.
2. Fill cooler.
3.
as shown at left. *
4. Make sure intake li
cooler.
5. Follow Set-up / Operation instructions on page 5.
* Model PMpump enclosure is specifically made to fit a 10-
cooler, supplied by the user.
PM-18FO WITH ANY OTH
RESERVOIR!
TIP HAZARD
•
Serious injury may occur.
•
Support weight of fan with
free hand when moving cart.
•
Do not fill cooler before
moving cart.
To prepare model PM-18C for operation:
1. Assemble as described on pages 3 and 4.
2. DO NOT FILL COOLER B
MISTER CART.
weight (ap
hazardous to move.
3. Carefully move mister cart to desired location
4. Remove pump enclosure and hang it on the slot
located on the fan yoke (see detail views at left)
5. Fill cooler
6. Replace pump enclosure on cooler
7. Follow Set-up / Operation instructions on page 5
– Pump enclosure should not be hung from yoke for
extended periods of time.
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 6 of 8
7
6
11
10, 12
ASSEMBLED VIEW AND REPLACEMENT PARTS LIST
FOR PM-18FO & PM-18S
8
1
2
4
3
16
14
8
13
5
ITEM # QTY. P/N DESCRIPTION
1 1 6399099 FRONT GUARD (PAINTED)
2 1 63991002 REAR GUARD (PAINTED)
3 1 58381001 SUPPORT TUBE ASSEMBLY
4 1 58364003 MOTOR TOTALLY ENCLOSED
5 1 44115001 CORDSET
6 1 58299008 FAN BLADE ASSEMBLY
7 1 44114001 SWITCH (TOGGLE-WATER PROOF)
8 5 44108001 NOZZLE (BRASS)
9 1 44105001 TUBING (1/4" NYLON) 80" LENGTH
10 2 3443032 BOLT 1/4" - 20 X 1.500" CARRIAGE
11 2 2480700 RUBBER BUSHING
12 2 0004901 NUT 1/4" - 20 HI-CROWN NYLON
13 1 63924001 COOLER (10 GAL.)
14 2 44108002 PLUG
15 1 44104001 FILTER
16 1 58467001 MISTING HUB
17 1 2489800 BARB FITTING – NOT SHOWN
(Connects intake line hose to filter)
18 1 2490000 TUBING 14-1/2” – NOT SHOWN
(Intake line hose)
19 1 2419200 Half Coupling – NOT SHOWN
(Connects to intake side of filter)
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 7 of 8
MAINTENANCE
ge with
changing water conditions. The filter should be
inspected frequently and changed as needed. A
dirty filter will restrict water flow to the pump and
The fog or spray pattern exiting from the nozzles
. If this is not the
case, the nozzle should be cleaned or replaced.
Nozzle function should be checked regularly to
Clogged nozzles can be cleaned by removing them
ing them in a scale or
lime removing solution. If nozzles fail to work after
When it is time to store the Power Mister or take it
e for more than a few days, it is strongly
recommended that the water be drained from the
system to prevent calcification problems and the
formation of algae. Also be sure to empty the Igloo
Regularly clean the mister and Igloo cooler with an
workmanship or in the design or
function of our equipment, you may return it to us for repair, replacement, or credit at our
discretion. A returned goods number will be issued at the time you contact us. This
oper credit for your return. Shipping costs
amage, cost of repair, incidental or consequential
damages of any kind, whether based on warranty, contract or negligence, and arising in
connection with the sale, use or repair of the Products. Seller's maximum liability shall
ontract price for the Products claimed to be defective or
Equipment may be accepted for return with in 90 days of shipment, when authorized by
us with our return labels. Request necessary permission and special Return
Authoriza
tion Tags. Currently listed equipment in new and unused condition, and in
factory sealed cartons, may normally be returned for full credit less 25% (minimum
charge $20.00) charge for handling, repacking and restocking, and less transportation
ways, at net prices prevailing at time of purchase or time of return,
whichever is lower. TPI Corporation, however, reserves the right to refuse any return, at
our discretion, if TPI Corporation is not responsible for error. All special, custom made or
uipment with special finishes, and modified versions of cataloged numbers are not
returnable. All returned merchandise is subject to inspection. Unsalvageable and
Minimum charge on replacement will be waived if order is accompanied by copy of proof
of claim submitted to carrier. No repair, replacement, or other adjustment by the
customer is authorized by us, unless so stated in writing by our Sales Service
WARRANTY
ELECTRICAL SHOCK
HAZARD
• Serious injury or death may
occur.
• Disconnect from electrical
supply before performing
any maintenance operations.
FILTER
Filter maintenance requirements will chan
can cause permanent damage.
NOZZLES
should have an even cone shape
assure best misting and evaporation performance.
from the misting hub and soak
cleaning, replace them with spare nozzles provided.
Tighten nozzles by hand only.
Before reinstalling nozzles, flush water line to
misting hub.
SYSTEM DRAIN / STORAGE
out of us
cooler.
anti-bacterial solution.
TPI CORPORATION - P.O. Box 4973
Johnson City, TN 37602-4973
(800) 251-0382
TPI Corporation’s Guaranteed Customer Satisfaction Warranty States:
If you are ever dissatisfied with the quality of our
number is necessary to assure that you get pr
for returns are at the expense of the customer unless otherwise negotiated.
We want satisfied Customers and will make every effort to satisfy our customers.
IN CASE OF PRODUCT FAILURE:
It shall be the obligation of the owner to furnish to the company the following information:
1. Model Number and date of manufacture of product involved.
2. Complete description of the problem encountered with product.
SELLER'S LIABILITY
Seller will not be liable for any loss, d
not in any case exceed the c
unsuitable.
RETURNED GOODS
charges both
eq
damaged merchandise will be credited at salvage value or less costs of repairs.
DAMAGED GOODS
department.
Issue Date: 3-11-05 Rev. Date: 9-12-07 Rev. Level: 13 ECN: n/a OIPM P/N: 3420433
Page 8 of 8
Loading...