720b
Combustible Gas Leak Detector
The Value Leader
TM
www.tpi-thevalueleader.com
Contents
• Specifications
• Product Features
• Standard Accessories
• Optional Accessories
• General Description
• Operating Instructions
• Battery Replacement
• Operation Check
• Sensor Replacement
• Warranty
Specifications
Power Supply: 2 "C" Alkaline Batteries
Sensor: Solid State
Sensitivity: 10 ppm Methane
Warm up: Approx 1 minute
Response time: Instantaneous
Duty Cycle: Continuous
Battery Life: Approx. 30 hrs.
Size: 3.0" x 9.5" x 1.75"
(77 x 240 x 47) mm
Weight: 1.1 lbs (500g)
Probe Length: 16" (406mm)
Standard Accessories
Sensor: A739
Instruction Manual: 720b Instruction Manual
Soft Pouch A700
Optional Accessories
Hard Case A714
Earphone A710
Gooseneck
Speaker
Battery
Compartment
Standard Accessories
Sensor: A739
Instruction Manual: 720b Instruction Manual
Soft Pouch A700
Optional Accessories
Hard Case A714
Earphone A710
Sensor
Earphone
jack
Gooseneck
Speaker
Visual leak
indicator
On/Off
switch
Battery
Compartment
General Description
The 720b is an advanced state-of-the-art leak
detector capable of detecting many combustible,
noncombustible and toxic gases.
The following is a partial list of gases that the
720b is sensitive to:
Acetone, Alcohol, Ammonia, Steam, Carbon
Monoxide*, Butane, Gasoline, Jet Fuel, Hydrogen
Sulfide, Smoke, Industrial Solvents, Methane,
Lacquer Thinner, Naphtha, Propane, Natural Gas.
*Not to be used to quantify the amount of CO
present.
Operating Instructions:
1. Turn the unit on in an uncontaminated
environment (clean air away from the system in
question) by moving the switch from the
OFF position to the ON position.
2. The GREEN ready light will illuminate if there is
ample battery power. The RED LED may
flicker and the tick may sound during the
warm-up. To silence the tick, rotate the thumb
wheel fully counterclockwise.
3. Adjust the TICK ADJUST by rotating the thumb
4. Approach suspected leak areas with the sensor
5. If the GREEN LED changes to orange color,
6. An earphone can be plugged into the earphone
9. If the instrument does not perform or it has been
Battery Replacement
1. Remove the battery compartment cover from the
2. Remove the batteries and replace by sliding the
wheel in a clockwise direction until a uniform
ticking sound is heard. The RED light will flash
at the same time the tick sounds.
4. Approach suspected leak areas with the sensor
until the tick begins to increase. When the tick
increases, do not move the sensor from the area,
rotate the TICK ADJUST slightly counterclockwise to slow the ticking and continue to
approach the suspected leak area with the sensor. Continue to slow the tick until the location
of the leak is found. If the tick stops, the concentration level has decreased. Move back in the
opposite direction to find the leak again.
5. If the GREEN LED changes to orange color,
change the batteries.
6. An earphone can be plugged into the earphone
jack when using the instrument in noisy environments.
9. If the instrument does not perform or it has been
damaged, follow the Operation Check section of
this manual.
Battery Replacement
1. Remove the battery compartment cover from the
bottom of the handle by sliding the door away
from the front side of the instrument.
2. Remove the batteries and replace by sliding the
negative (-) end of the batteries in first.
3. Replace the battery cover by sliding the door
into the slots provided in the handle and allow it
to snap into place.
4. For best performance use quality alkaline
batteries.
Operation Check
To verify the operation of the 720b simply turn
the unit on and allow it to warm up for approximately 1 minute. Expose the sensor to a known
gas source such as an unlit butane lighter. The
tick should increase when the gas in applied.
The tick will decrease when the gas is removed.
If the unit fails to respond, the sensor may need
replacing or the unit may need to be sent in for
repair:
CAUTION: This unit must be sent to a factory
authorized repair center for all repairs.
Sensor Replacement
1. Turn the 720b off.
2. Pull off the sensor cap.
3. Unplug the old sensor and discard.
4. Replace sensor and sensor cap.
5. Turn on unit and perform “Operation Check”
Warranty and repair/exchange policy
Your TPI 720b is warranted to be free from
defects in materials and workmanship for a period of one year after purchase (excluding sensor,
calibration and batteries). If within the warranty
period your instrument should become inoperative from such defects, the unit will be repaired
or replaced at our option. This warranty covers
normal use and does not cover damage which
results from alteration, tampering, accident,
misuse, abuse, neglect or improper
maintenance. A purchase receipt or other proof
of original date of purchase will be required
before warranty performance will be rendered.
Instruments out of warranty will be repaired for a
service charge. Return the unit postpaid and
insured to:
Test Products International, Inc.
9615 SW Allen Blvd.
Beaverton OR 97005
(503) 520 9197
This warranty gives you specific legal rights and
you may also have other right which vary from
state to state.
Copyright © 2001, Test Products International, Inc
The Value Leader
TM
www.tpi-thevalueleader.com
Test Products International, Inc.
9615 SW Allen Blvd
Beaverton, OR 97005-4814 USA
750a Instruction Manual
Loading...