TPI 708 User Manual

708
Rev. 2.x Analyzers
Combustion Efficiency Analyzer
The Value Leader
TM
www.tpi-thevalueleader.com
Contents
1. Introduction
2. General Overview
3. Instrument Overview
3.1 Front View
3.2 Back View
3.3 Side Views
3.4 Top View
4. Turning On & Off
4.1 Turning On
4.2 Turning Off
4.4 Activating The Backlight
5. Combustion Analysis
5.1 Overview
5.2 Procedure
5.3 Combustion Displays
5.4 Typical Test Locations
5.5 Typical Test Results
6. Function Selection
6.1 Function 1 - Thermometer
6.4 Function 2 - Date / Time
6.5 Function 3 - Combustion Analysis
7. Saving Data
8. Recalling Data
9. Printing Data
Appendix A Specifications Appendix B Calibration & Service Appendix C Guarantee Appendix D Installing the Optional A773 Filter Appendix E Error Codes and Trouble Shooting Appendix F CO Alarm & Auto Power Off Appendix G Manually Initializing Sensors
1. Introduction
2. General Overview
The TPI 708 combustion analyzer uses state of the art electrochemical sensors. This sensor technology provides the longest lasting, most accurate and reliable means for performing combustion tests. The sen­sors in your analyzer will need to be replaced periodically and calibra­tion is recommended once every year.
Electrochemical sensors by nature are always active. Therefore the time the analyzer is off and not being used must be taken into account when determining sensor life. The sensors in your analyzer are war­ranted for two years. This warranty does not cover sensors damaged through misuse of the analyzer.
You should keep the battery of your 708 charged so power is constant­ly being supplied to your sensors.
The following guidelines will help prevent damage to your sensors:
Always use the mini pump filter when testing flue gases. Always periodically check and replace the mini pump filter as needed. Always make sure the in-line filter / water trap is installed properly. Always periodically check and replace the in-line filter as needed. Always remove water or condensation from the inside of the in-line fil­ter / water trap assembly prior to performing tests. Always use the optional oil filter (p/n A773) when performing tests on oil burning equipment.
General Overview (Continued)
Never over saturate your sensors by performing tests on equipment with gas levels beyond the capability of you analyzer.
Always keep the A762 water trap / filter assembly clean and replace the fil­ter as necessary. Replacement filter part number is A762F.
This manual will guide you through the functions of the TPI 708 which will give you many years of reliable service.
Your TPI 708 Flue Gas Analyzer comes complete with the following stan­dard accessories:
TPI 708 Instrument
Rubber Boot (A765)
Soft Carrying Case (A768)
Flue Sampling Probe (A770)
In-Line Filter assembly installed on Flue probe (A762)
Temperature Probe (GK11M)
Mini Pump Protection Filter Assembly and spare filters (A763)
Exhaust Spigot (removable) (A764)
Instruction Manual
( ) Denotes part number
Your TPI 708 Flue Gas Analyzer has the following options available:
Infrared printer (A740)
Spare In-Line Filter (A762F is a package of 5 filters)
3. Instrument Overview
3.1 Front View
Rubber Boot Protects the instrument from accidental damage
Display Large 3 Parameter Backlit LCD Display
Battery Condition Icon Shows condition of batteries.
Keypad Selects all available functions
Selected Fuel Type N GAS, LPG, LIGHT OIL, HEAVY OIL, OPT 1
(Bituminous Coal), OPT 2 (Anthracite Coal), OPT 3 (Coke), OPT 4 (Butane), OPT 5 (Wood), OPT 6 (Bagasse)
Rubber Boot
LCD Display
Keypad
Battery Condition Icon
Selected Fuel Type
Scrolls through selectable fuels (see 3.1 ) Switches between Gross and Newt Efficiency (see 4.1.2) Switches between ºC and ºF (see 4.2.1) Moves up through the Stored Data Addresses (see 5, 6 & 7)
Moves down through the Stored Data Addresses (see 5, 6 & 7)
Scrolls through Combustion Analysis Displays Scrolls through Function Screens (see 4.1)
Turns temperature differential calculation ON/OFF (see 4.2.1) Turns ch2 temperature ON/OFF (see 4.3.1) Allows you to change the Date and Time (see 4.5) Allows you to choose a Stored Data Address (see 5, 6, 7, & 8)
Sends stored data to a separate infrared printer (see 7)
Allows you to view stored data on the display (see 6)
Stores readings to memory (see 8)
Scrolls through and selects analyzer functions (see 4) Turns Backlight ON and OFF (see 4)
Turns the instrument ON and OFF (see 3.1 & 3.2)
Print
Recall
Store
Func
Scroll
Enter
3.2 Back View
Sample Inlet Port: Connection for Gas Sampling Probe (see
3.4 & 5.2)
Connection for Mini Pump Protection Filter (see 3.4 & 6.2)
Calibration and Information Label: Displays calibration information and
Displays serial number
Battery Compartment: Holds “AA” batteries
Calibration and Information Label
Battery Compartment
Connection for Mini Pump Protection Filter
Sample Inlet Port
3.3 Side Views
Exhaust Port Port for connection of Exhaust Adapter
Infrared Window Window for sending stored data to IR Printer
(see 9)
Rubber Boot Protects the instrument from accidental damage
Exhaust
Port
Infrared Window
Rubber Boot
T1 Socket Connection for thermocouple plug on flue
probe (see 5.2) Connection for any 'K' type thermocouple probe (see 6.1)
T2 Socket Connection for any 'K' type thermocouple
probe (see 5.2 & 6.1)
Gas Sampling Port Connection for Gas Sampling Probe (see 5.2)
3.4 Top View
T1
T2
Gas Sampling Port
4. Turning On & Off
4.1 Turning On
Always: - Before turning on please ensure that the Mini Pump Protection Filter
assembly and the Temperature Sampling Probe complete with In-Line Filter or the Tubing & In-Line Filter for Leak Detection are not connected to the Gas Sample Port (see 2.2 or 2.4)
Press and hold down the Power Key and the TPI 708 will start its 30 second countdown 'PURGE' will be displayed: - The instrument MUST be turned on in a clean air environment as the 30 second purge will set the Carbon Monoxide level to Zero and the Oxygen to 20.9%. Ensure that the filters are clean and dry as dirty or wet filters will result in a loss of flow rate and 'Lo Flo' will be displayed to inform you that filters should be changed
During the last 20 seconds of the 30 second purge time the user can scroll through the following Fuels: - Natural Gas, LPG, Light Oil, Heavy Oil, OPT1 : Bituminous Coal, OPT 2 : Anthracite Coal, OPT 3: Coke, OPT 4: Butane, OPT 5: Wood (Dry), OPT 6: Bagasse by pressing the Up Arrow Key to select the Fuel they are working with. When desired fuel is displayed release the key, displayed fuel is now selected.
After the 30 second countdown the instrument is ready to take Flue, Temperature, Pressure or Leak Detection readings and Combustion Display 1 will be the first display.
The 708 will auto power off if no keys have been pressed for 10 minutes and the CO level is below 15ppm. This feature can be disabled see Appendix F.
The Scroll/Enter Key allows you to scroll through the combustion displays as out­lined in section 5.3. The Func Key is used to select the 708 function mode and allows you to set it to be a combustion analyzer, manometer, thermometer, or combustible leak detector. In addition, the Func Key is used to access the date and time display. See section 6 for more information on the Func Key.
NOTE: When selecting oil as fuel be sure to use the optional
oil filter (A773) or readings could become erratic. See Appendix E for installation instructions.
4.2 Turning Off
Always: - Before turning off return the instrument to a clean air environment and allow the Carbon Monoxide level to return to below 15ppm and the Oxygen level to return to 20.9% (± 0.3%) Press the Power Key to turn the instrument off:­NOTE Should you attempt to turn the instrument Off and the CO reading is above 15ppm then the instrument will remain On and a short Beep will be heard. The Instrument can only be switched off if the CO is below 15ppm
The instrument has an auto shut off after 10 minutes should no keys have been pressed for this period and as mentioned above that the CO is below 15ppm. Should the CO be above 15ppm then the 10 minute auto shut off countdown will not begin till the CO has gone below 15ppm
4.3 Activating the Backlight
The display backlight can be activated at any time by pressing and holding down the Func Key for approximately 2 seconds. The backlight will automatically shut off after approximately 20 seconds to preserve battery life.
5. COMBUSTION ANALYSIS
5.1 Overview
Testing for carbon monoxide, oxygen, and stack temperature is very important to the overall safety and efficiency of heating equipment. The following guidelines and descriptions are generic and meant to provide you with a basic understand­ing of combustion testing. TPI always recommends you contact the manufacturer of the device under test, obtain information specific to the device, and follow the procedures and safety guidelines for performing tests and affecting repairs.
In general, for most applications flue gas samples should be taken prior to the draft diverter or any other opening that allows room air to enter the system. This prevents room air from mixing with gases in the flue and diluting the test sample. To ensure accurate and consistent combustion tests, it is important gas and tem­perature samples be taken at the same location. This is easy with the TPI flue probe because the temperature sensor is an integral part of the probe.
Prior to taking a sample, the device under test should be on and operating. Putting the flue probe in the sample area prior to starting the device may cause saturation of the sensors due to the higher initial concentration of carbon monox­ide that may be encountered upon start up. If this happens, allow your analyzer to purge in fresh air until the carbon monoxide level returns to 0 ppm and the oxy­gen level returns to 20.9%. This may take more than an hour depending on how saturated the sensors are.
The included figures show locations for performing tests on commonly encoun­tered equipment. Remember to consult with the manufacturer of the device under test for specific test information.
NOTE: When selecting oil as fuel be sure to use the optional
oil filter (A773) or readings could become erratic. See Appendix E for installation instructions.
COMBUSTION ANALYSIS (Continued)
5.2 Procedure
1. Turn the 708 on as outlined in section 4.1. At any time you can activate the Backlight by holding down the Func/Backlight Key for 2 seconds. The back­light will automatically shut off after 20 seconds to preserve battery life.
2. Ensure you have connected the Mini Pump Protection Filter assembly and Temperature Sampling Probe complete with In-Line Filter to the Gas Sample Port (see 3.2 or 3.4) and the 'K' Type Thermocouple Plug into Thermocouple (T1) Socket (see 3.4). The GK11M ambient air temperature probe must be connected to the (T2) socket. (refer to figure below for correct hookup)
WARNING: - Ensure that the In-Line Filter hangs in a vertical position when readings are being taken, particularly if water is visible. Failure to comply may result in damage to the instrument.
WARNING: - There is ONLY one correct way to connect the 'K' type thermo­couple plug into the socket (see 2.4). Forcing the plug into the socket the wrong way round may result in damage to the instrument.
3. Insert the flue probe into the test location of the device under test. The probe tip should be in the middle of the flue pipe or exhaust stream. Refer to figures 1 through 3 for typical test locations.
Mini Pump Protection Filter Assembly
Ambient Air Connection (T2)
GK11M Probe
Flue Probe Connection (T1)
In-line Filter Assembly
Flue Probe Tubing
COMBUSTION ANALYSIS (Continued)
4. As seen below, use the Scroll/Enter Key to move through the various com­bustion displays.
5.3 Combustion Displays
You can move through the following Combustion Analysis Screens by repeat­edly pressing Scroll/Enter:
Combustion Display 1 (Default Start Up Display)
• Displays Carbon Monoxide (CO) reading in parts per million (ppm)
• Displays calculated Carbon Dioxide (CO2) figure in percentage (%)
• Displays calculated CO/CO2 (Ratio) figure
WARNING: - Should the CO reading rise above 2,000ppm a continuous series of Alarm Beeps will be heard. The Probe should immediately be disconnected from the instrument and the instrument returned to a clean air environment. This Alarm alerts the user that there is a high concentration of CO, and this procedure will protect the sensors within the instrument.
Combustion Display 2
• Displays Oxygen (O2) reading in percentage (%)
• Displays calculated Excess Air (X Air) figure in percentage
• Displays calculated Efficiency (Eff.) figure in percentage
• Pressing the Up Arrow Key will toggle between Gross &
Net Efficiency (Note: Gross Efficiency is used in the USA)
Combustion Display 3
• Displays Carbon Monoxide (CO) reading in parts per million (ppm)
• Displays Oxygen (O2) reading in percentage (%)
COMBUSTION ANALYSIS (Continued)
5.3 Combustion Displays (continued)
Combustion Display 4
• Displays CO air free (-CF-)
Combustion Display 5
• Displays Temperature reading of Channel 1 (T1) in degrees Centigrade (ºC)
• Displays Temperature reading of Channel 2 (T2) in degrees Centigrade (ºC)
• Displays the Differential Temperature (Diff.) between ch1 and ch2 in ºC
• 'oPEn' will be displayed if no 'K' type probe is connected to the thermocouple socket
5.. During a combustion test you can save, print, and send data to a computer. See section 7 through 11. Allow readings to stabilize before saving or printing the data.
6. After the test is complete, remove the flue probe from the test location and allow the analyzer to purge in a fresh air environment. Turn the analyzer off as outlined in section 4.2.
NOTE: When selecting oil as fuel be sure to use the optional
oil filter (A773) or readings could become erratic.
5.4 TYPICAL TEST LOCATIONS
Atmospheric Gas Fired Fan Assist Boiler / Furnace
Typical Test Locations
COMBUSTION ANALYSIS (Continued)
Figure 1
COMBUSTION ANALYSIS (Continued)
Condensing Boiler / Furnace
Typical Test Locations
Figure 2
COMBUSTION ANALYSIS (Continued)
Test all exhaust ports at the top of the heat exchanger.
Atmospheric Forced Air Furnace
Typical Test Locations
Figure 3
COMBUSTION ANALYSIS (Continued)
5.5 TYPICAL TEST RESULTS
Actual test results vary depending on the equip­ment under test. TPI recommends you check with the manufacturer of the equipment being tested to determine specific acceptable results.
Oxygen 3% to 6%
Carbon Monoxide Less than 100ppm (air free)
Stack Temperature 300°F to 500°F
Draft -0.15 inH2O
Oxygen 4% to 7%
Carbon Monoxide Less than 100ppm (air free)
Stack Temperature 325°F to 625°F
Draft -0.15 inH2O
Power Burners (Gas Fired)
Power Burners (Oil Fired)
Oxygen 7% to 9%
Carbon Monoxide Less than 100ppm (air free)
Stack Temperature 325°F to 500°F
Draft -0.15 inH2O to -0.4 inH2O
Gas Fired Burners (Atmospheric / Fan Assist)
6. FUNCTION SELECTION
Pressing the Func Key enables access to the different functions available on the 708. Available functions are: Combustion Analyzer, Thermometer,
Manometer, and Date / Time display.
6.1 Function 1: - Thermometer
Press the Func Key repeatedly to access the thermometer function. In this mode the 708 functions like a K-Type thermocouple thermometer. The pump will stop running when in this function.
1. Ensure you have a 'K' type probe connected to one or both of the thermo­couple sockets T1 or T2 (refer to figure below) WARNING: - There is ONLY one correct way to connect the 'K' type thermo­couple plug into the socket (see 4.2). Forcing the plug into the socket the wrong way may result in damage to the instrument.
2. Touch the temperature probe to the item under test and read the displayed
temperature.
Other Features:
• Pressing the Up Arrow Key will toggle between ºC and ºF
• Pressing the Scroll/Enter Key will toggle the Differential Temperature ON and OFF
• 'oPEn' will be displayed if no 'K' type probe is connected to the thermocou­ple socket
The thermometer func­tion allows you to per­form temperature tests.
Function Display 1 (Temperature)
T1 Temperature T2 Temperature Differential Temperature
6.4 Function 2: - Date/Time
Press the Func Key repeatedly to access the date/time screen. From this func­tion Time, Date and Year can be changed.
1. Once the Time, Date, and Year screen is displayed, press the Scroll/Enter Key once to allow you to change the data.
2. Press the Up Arrow Key to Increase the Minutes
3. Press the Down Arrow Key to Decrease the Minutes
4. Press the Scroll/Enter Key to confirm the desired Minute and move onto the Hours
5. Repeat steps 2 to 4 to change the Hour, the Day, the Month and the Year
6. The unit will return to normal after the desired Year has been confirmed
6.5 Function 3: - Combustion Analysis
Press the Func Key repeatedly to return to Combustion Analysis mode and the default display (Combustion display 1)
Combustion Display 1 (Default Start Up Display)
• Displays Carbon Monoxide (CO) reading in parts per mil­lion (ppm)
• Displays calculated Carbon Dioxide (CO2) figure in per­centage (%)
• Displays calculated CO/CO2 (Ratio) figure
Function Display 2 (Date / Time)
Time Date / Month Year
7. SAVING DATA
During testing, data can be stored for later retrieval by following these steps:
1. Press the Store Key once 'Addr' will be displayed on the top line along with a location number from 0 to 49 flashing on the screen. Select the required address location that you wish to save the data to by pressing the Up and Down Arrow Keys
2. Press the Scroll/Enter Key once The location number which you have chosen will stop flashing and after about 3 seconds the instrument will return to the screen/function you were previous­ly on.
You have just successfully stored a set of readings which can be either reviewed on screen (see 8) or sent to the IR printer (see 9)
When data is saved, all data previously in the address will be overwritten.When saving pressure/draft readings, select an address different from the one used to save combustion readings.
8. RECALLING DATA
1. Press the Recall Key once 'Addr' will be displayed on the top line along with a location number from 0 to 49 flashing on the screen. Select the required address location that you wish to save the data to by pressing the Up and Down Arrow Keys
2. Press the Scroll/Enter Key once The Time & Date of the Saved Data from the selected address location will be displayed flashing on the screen. The rest of the Saved Data at this address location can be reviewed by pressing the Up and Down Arrow Keys
4. Press the Scroll/Enter Key once when you are finished reviewing the data. 'End' will be displayed with 'YES' flashing
5. Press the Scroll/Enter Key once to EXIT or
6. Press the Up or Down Arrow Keys 'End' will be displayed with 'no' flashing
7. Press the Scroll/Enter Key once to CHOOSE another address location to review and repeat steps 2 to 5
9. PRINTING DATA
WARNING: - To operate correctly there must be a clear line of sight between
the Infrared Window on the instrument (see 3.3) and the Infrared Window on the IR Printer (see Printer instructions). Place the printer so it is no closer than approximately 6 inches from the analyzer.
1. Press the Print Key once 'rEAL' and “Stor’ will be displayed and ‘rEAL’ will be flashing. Selecting ‘rEAL’ will cause the 708 to print the test data currently on the display (real time data). Selecting ‘Stor’ will cause the 708 to print data stored in memory. Use the Up and Down Arrow Keys to select the desired print mode and press the Scroll/Enter Key.
REAL Print Mode - If rEAL print mode is selected, the analyzer will dis­play ‘Wait’ ‘out’ and bars will change position on the LCD until printing is complete.
After printing is complete, ‘End’ will be displayed and ‘YES’ (or ‘no’) will blink. Selecting ‘YES’ will return the 708 to normal operation, selecting ‘no’ will return the 708 to the print selection screen so you can print again. Use the Up and Down Arrow Keys to make the selection and press the Scroll/Enter Key.
STOR Print Mode - If Stor mode is selected, 'Addr' will be displayed on the top line along with 'SA ' and a location number from 0 to 9 will be flashing on the screen. Select the required address location that you wish to print data from by pressing the Up and Down Arrow Keys and press the ‘Scroll/Enter’ Key. The analyzer will display ‘Wait’, ‘out’ and bars will change position on the LCD until printing is complete.
After printing is complete, ‘End’ will be displayed and ‘YES’ (or ‘no’) will blink. Selecting ‘YES’ will return the 708 to normal operation, selecting ‘no’ will return the 708 to the print selection screen so you can print again. Use the Up and Down Arrow Keys to make the selection and press the Scroll/Enter Key.
Combustion and pressure/draft printouts must be performed separately. Perform a combustion test and save the data. Perform a pressure/draft test and save the data in a different address. Print each address sepa­rately.
Appendix A : SPECIFICATIONS
Instrument
Operating Temperature Range 14°F to +122°F (-10°C to +50°C) Battery 1.5V AA size (3) Battery Life > 6 Hours Fuels Natural Gas, LPG, Light Oil, Heavy Oil
OPT 1 (Bituminous Coal), OPT 2 (Anthracite Coal), OPT 3 (Coke), OPT 4 (Butane), OPT 5 (Wood), OPT 6
(Bagasse) Display Backlit LCD Data Storage 50 sets of readings Time & Date 24 Hour Real Time Clock Dimensions 200mm x 90mm x 60mm Weight 500g Casing Rubber Boot as Standard Switch Off Failsafe Exhaust Safety Spigot Conforms to BS7927 (and the draft BS7967)
Flue Temperature Probe
Construction Pistol Grip with Stainless Steel Shaft Hose Length 2500mm Insertion Length 200mm 'K' Type Thermocouple Accuracy +/- 0.3%, +/- 1°C Maximum Temperature 800°C
Gases
Range Resolution Accuracy Oxygen 0-25% 0.1% +/- 0.3% Carbon Monoxide 0-10,000 ppm 1 ppm +/- 5 ppm or 5%
Whichever is greater Carbon Dioxide 0-25% 0.1% Calculated CO/CO2 Ratio 0-0.999 0.001 Calculated Combustion Efficiency 0-100% 0.1% Calculated
Appendix B: CALIBRATION & SERVICE
It is recommended that the instrument be calibrated every 12 months. Please
consult Test Products International for further details.
The following are consumable parts for the instrument:
In-Line Filter Element (pkg of 5) User Replaceable A762F Mini Pump Protection Filter Assem. User Replaceable A763 **Oxygen Sensor User / Factory Replaceable A761 **Carbon Monoxide Sensor User / Factory Replaceable A760
**Sensor replacement requires calibration gas.
The following are accessories for the instrument:
Flue Temperature Probe w/k-type Standard A770 'K' Type Temperature Probe Standard GK11M In-Line Filter Complete Standard A762 Mini Pump Protection Filter Assem. Standard A763 Rubber Boot Standard A765 Infrared Printer Optional A740 Soft Carrying Case Standard A768 Exhaust Spigot Standard A764
Appendix C: GUARANTEE
Your TPI 708 Flue Gas Analyzer is guaranteed free from defects in materials and workmanship for 3 Years from the date of purchase. This guarantee does not affect your statuary rights. For additional information please refer to the included warranty card or contact TPI at 800-368-5719.
To obtain warranty performance or maintenance on your analyzer: - Include with the product your name, address, phone number, written description of the problem and proof of purchase date. Carefully package and return to:
TPI / Attn. Repair 9615 SW Allen Blvd. Suite 104 Beaverton, OR 97005
Appendix D: INSTALLING THE OPTIONAL A773 OIL FILTER
When performing combustion tests on oil fired equipment it is important to use the optional A773 oil filter to ensure stable readings. The A773 does not have to be removed when working with other types of fuels.
PROCEDURE
1. Pull the yellow thermocouple out of the cord channel in the tubing up to the cord stop.
2. Cut the tubing approximately 1 1/2 inches from the end of the A762 water trap / fil­ter assembly.
3. Insert the A773 oil filter into the tube below the A762.
4. Cut the remaining piece of tube into a 1 1/2 inch piece and connect it onto the end of the A773 oil filter.
5.. Press the thermocouple cord into the cord channel.
The A773 should be replaced when most of the pellets become discolored.
Appendix E: ERROR CODES & TROUBLESHOOTING
The 708 analyzer will display certain codes to let you know of a malfunction.
Code
Displayed
Code Definition Possible Causes Corrective Action
Flo Err
Pump not drawing sample at correct flow rate.
Blockage / kink in flue probe hose.
Dirty or blocked filter(s). Worn pump.
Check and rectify.
Replace filter(s). Return to TPI for service.
InIt
O2
Err
Oxygen sensor failed to ini­tialize
Flue probe connected to 708 prior to power up.
708 did not purge completely from last sample.
Worn or defective oxygen sensor.
Disconnect probe and restart.
Purge for 20 minutes and restart.
Return to TPI for sensor replacement or install new sensor.*
Try manually initializing the sensor. See Appendix G.
InIt CO Err
Carbon monoxide sensor failed to initialize.
Flue probe connected to 708 prior to power up.
708 did not purge completely from last sample.
Worn or defective carbon monoxide sensor.
Disconnect probe and restart.
Purge for 20 minutes and restart.
Return to TPI for sensor replacement or install new sensor.*
Try manually initializing the sensor. See Appendix G.
Lo
bat
Low battery.
Battery needs to be charged.
Charge battery. If the battery won’t hold a charge, replace the battery.
oFL
Overflow indication. The car­bon monoxide being mesured is above the instru­ments capability.
CO being measured is too high or low.
Remove the CO source and allow the 708 to purge.
oFL
Overflow indication. The tem­perature being measured is outside the maximum mea­surement capability.
Temperature being measured is too high or low.
Remove pressure source.
oPEn
Unable to read thermocouple (temperature).
Temperature probe not con­nected to input. Worn temperature sensor.
Connect temperature probe to analyzer. Replace temperature probe or flue probe.
*Sensor replacement requires calibration gas.
Appendix E: ERROR CODES & TROUBLESHOOTING (Continued)
Problem Possible Cause Corrective Action
Efficiency reading incorrect NET efficiency selected.
Ambient temperature probe not plugged in to T2.
Incorrect fuel selected.
Select GROSS efficiency. See section 5.3.
Plug ambient probe into T2. See section 5.2.
Select the proper fuel for the equipment being tested. See section 4.1.
Readings are erratic when working on oil fired equip­ment.
Oil filter not installed or installed incorrectly.
Make sure the optional oil fil­ter (A773) is installed. See Appendix D.
One or all of the following parameters; Ratio, CO air free, excess air, and efficien­cy read and print dashes.
Measured values are such that the calculated values of these parameters are out of range.
Redo combustion test. Since these are calculated values, the measure values must be within certain levels for these to display. If the measured oxygen level is above 19.9% these parameters won’t read.
These parameters might not display or be applicable in some tests.
Analyzer won’t turn off
Oxygen and/or carbon monoxide levels outside lim­its.
Allow the analyzer to purge longer.
Appendix F: CO ALARM & AUTO OFF SETTINGS
Setting the Carbon Monoxide Alarm Point and/or Auto Power Off Mode
The CO alarm and auto power off settings can be changed as necessary by per­forming the following procedure.
WARNING : Changing parameters in field calibration mode can adversely affect the operation of your analyzer. Follow the instructions carefully.
1. Press and hold the Scroll/Enter Key down until ‘FILD CAL’ is displayed. The 708 will cycle through a 30 second countdown then display ‘CAL’, Air’, gAS’.
2. Use the Up Arrow Key to select ‘Air’ by making it blink. Press the Scroll/Enter Key to accept the selection.
3. 708 Display: ‘CAL’, ‘FLo’, ‘oPEn’. Action : Press the Func Key to bypass.
4. 708 Display: ‘CAL’, ‘FLo’, ‘CLos’. Action : Press the Func Key to bypass.
5. 708 Display: ‘0ppm’, ‘Co’, ‘rEF’. Action : Press the Func Key to bypass.
6. 708 Display: ‘20.9%’, ‘o2’, ‘rEF’. Action : Press the Func Key to bypass.
7. 708 Display: ‘2000’, ‘A-r’, ‘SEt’. Action : If you are not changing the CO alarm point press the Func Key. Otherwise press the Up and Down Keys to set the ppm level the alarm will sound at. Factory default is 2000ppm. Press the Scroll/Enter Key to accept the selection.
8. 708 Display: ‘Auto’, ‘oFF’, ‘En’. Action : If you are not changing the auto power off mode press the Func Key. Otherwise press the Up and Down Arrow Keys to enable (En) or disable (dis) the auto off function. Factory default is enabled (En). Press the Scroll/Enter Key to accept the selection.
9. 708 Display: ‘CAL’, ‘StoP’, ‘go’. Action : Press the Up Arrow Key to select ‘StoP’ by making it blink and press the Scroll/Enter Key to accept the selection. The 708 will return to normal operation
Appendix G: MANUALLY INITIALIZING SENSORS
Manually Initializing the Carbon Monoxide and Oxygen Sensors
If the CO or O2 sensor fails to initialize, this procedure can be performed to try and manually initialize the sensor(s).
WARNING : Changing parameters in field calibration mode can adversely affect the operation of your analyzer. Follow the instructions carefully.
1. Press and hold the Scroll/Enter Key down until ‘FILD CAL’ is displayed. The 708 will cycle through a 30 second countdown then display ‘CAL’, Air’, gAS’.
2. Use the Up Arrow Key to select ‘Air’ by making it blink. Press the Scroll/Enter Key to accept the selection.
3. 708 Display: ‘CAL’, ‘FLo’, ‘oPEn’. Action : Press the Func Key to bypass.
4. 708 Display: ‘CAL’, ‘FLo’, ‘CLos’. Action : Press the Func Key to bypass.
5. 708 Display: ‘0ppm’, ‘Co’, ‘rEF’. Action : Press the Scroll/Enter Key. After the 10 second countdown is complete press the Scroll/Enter Key twice.
6. 708 Display: ‘20.9%’, ‘o2’, ‘rEF’. Action : Press the Scroll/Enter Key. After the 10 second countdown is complete press the Scroll/Enter Key twice.
7. 708 Display: ‘2000’, ‘A-r’, ‘SEt’. Action : Press the Func Key to bypass.
8. 708 Display: ‘Auto’, ‘oFF’, ‘En’. Action : Press the Func Key to bypass.
9. 708 Display: ‘CAL’, ‘StoP’, ‘go’. Action : Press the Up Arrow Key to select ‘StoP’ by making it blink and press the Scroll/Enter Key to accept the selec­tion. The 708 will return to normal operation
If the 708 continues to fail to automatically initialize or this procedure fails to initialize the sensors, return your analyzer to Test Products International.
Notes: Notes:
Notes:Notes:
Test Products International, Inc.
9615 SW Allen Blvd., Ste. 104
Beaverton, OR 97005
Tel: 503-520-9197 Fax: 503-520-1225
www.tpi-thevalueleader.com
Test Products International, Ltd.
342 Bronte Road South, Unit #9
Milton Ontario Canada L9T5B7
Tel: 905-693-8558 Fax: 905-693-0888
Loading...