Toy State CAT Radio Control Truck Owner's Manual
CAUTION-ELECTRICALLY
OPERATED PRODUCT:
NOT RECOMMENDED FOR CHILDREN UNDER 5 YEARS
OF AGE. AS WITH ALL ELECTRIC PRODUCTS,
PRECAUTIONS SHOULD BE OBSERVED DURING
HANDLING AND USE TO PREVENT ELECTRIC SHOCK.
INPUT: 120V AC 60Hz 3.8W. OUTPUT: 12V DC 200mA.
RADIO CONTROL
DUMP TRUCK
OWNER’S MANUAL
BATTERY REQUIREMENTS:
4 “AA” Batteries (for Controller)
One 9.6V Rechargeable Power
Pack/Charger
(for Truck).
MADE IN CHINA
TOY STATE INDUSTRIAL LTD.
14 Science Museum Road, Kowloon, Hong Kong
Call for Help!
If you have questions about this toy
Call Toll-Free: 1-877-473-8015
Between 9:00 a.m. – 5:00 p.m. E.S.T. Monday thru Friday
Contact via e-mail: consumerservice@toystate.com
© 2004 Caterpillar
CAT, CATERPILLAR, and their design marks
are registered trademarks of Caterpillar Inc.
8
MANUFACTURERS NOTE
1
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE
“Modifications not authorized by the manufacturer may void users authority to operate the device.”
CAUTION
Important Battery Information
RECHARGEABLE BATTERY PACK IS NICKEL CADMIUM, BATTERY MUST BE RECYCLED OR DISPOSED
OF PROPERLY.
NOTE: 10 hour charging is recommended. The minimal time for charging is no less than 5 to 6 hours
to assure proper performance of the dump truck.
• Allow the battery pack to cool before recharging.
• Do not recharge batteries that are leaking or broken.
• Always disconnect battery pack from truck when not in use.
• Do not dispose of battery pack in fire.
• Dispose of NiCd battery packs properly.
• Always remove battery pack from vehicle before charging.
• Do not use charger for any other use other than instructed in directions.
• Use only batteries of the type recommended.
• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
• Do not mix old and new batteries.
• Remove batteries from truck if vehicle will not be used for a long period.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
PROBLEM! TRUCK DOES NOT MOVE
PROBLEM! TRUCK MOVES BY ITSELF
PROBLEM! TRUCK RUNS SLOWLY
TROUBLESHOOTING AND CARE FOR R/C TRUCKS
• Are the + and –‘s contacts correctly matched in the controller?
• Are the metal contact tabs touching, rusty or dirty in controller?
• Are there batteries in the vehicle and controller?
• Is the power switch turned on?
• Is the battery/power pack weak or out of power?
• Is the Lock button on the controller activated? Press again to start the engine.
• Are there batteries in controller?
• There is radio interference in the area.
• Another R/C vehicle with the same frequency is close by.
• The antenna of controller is not screwed in tight.
• The antenna is not fully extended.
• A supernatural phenomenon.
• There is radio interference in the area.
• Another R/C vehicle with the same frequency is close by.
• The antenna of controller is not screwed in tight.
• The antenna is not fully extended.
PROBLEM?PERFORMANCE DROP, INCONSISTENT MOVEMENT OR FAILS TO RUN
Recharge battery power pack for 5 to 6 hours minimum and replace batteries in controller with
new alkaline batteries.
Call 1-877-473-8015 for help!
FRONT END ALIGNMENT
Trim adjustment is located under vehicle between front
wheels. Adjust trim to align wheels for straight line driving.
Loading...