TOYOTA Tacoma 2012 User Manual

Abbreviation list

Abbreviation/Acronym list

ABBREVIATIONS MEANING

2WD Two Wheel Drive
4WD Four Wheel Drive

ABS Anti-Lock Brake System

ACC Accessory

ALR Automatic Locking Retractor

A-TRAC Active Traction Control

AUTO LSD Automatic Limited Slip Differential

CRS Child Restraint System
DAC Downhill assist control
ECU Electronic Control Unit
EDR Event Data Recorder

ELR Emergency Locking Retractor
GAWR Gross Axle Weight Rating
GCWR Gross Combination Weight Rating
GVWR Gross Vehicle Weight Rating

I/M Emission inspection and maintenance

LATCH Lower Anchors and Tethers for Children

LED Light Emitting Diode

LT Light truck

M + S Mud + Snow

MMT Methylcy clopentadienyl Manganese Tricarbonyl

MTBE Methyl Tertiary Butyl Ether

OBD On Board Diagnostics

RES Resume

RR DIFF LOCK Rear differential lock

RSCA Roll sensing of curtain shield airbag

SRS Supplemental Restraint System

612

ABBREVIATIONS MEANING

TIN Tire Identification Number
TPMS Tire Pressure Warning System
TRAC Traction Control

TWI Treadwear indicators

TWR Trailer Weight Rating

VIN Vehicle Identification Number

VSC Vehicle Stability Control

Abbreviation list

613

For your information

Main Owners Manual

Please note that this manual applies to all models explains and all equip­ment, including options. Therefore, you may find some explanations for
equipment not installed on your vehicle.

All specifications provided in this manual are current at the time of printing.
However, because of the Toyota policy of continual product improvement, we
reserve the right to make changes at any time without notice.

Depending on specifications, the vehicle shown in the illustrations may differ
from your vehicle in terms of equipment.

Noise from under vehicle after turning off the engine

Approximately five hours after the engine is turned off, you may hear sound
coming from under the vehicle for several minutes. This is the sound of a fuel
evaporation leakage check and, it does not indicate a malfunction.

Accessories, spare parts and modification of your Toyota

A wide variety of non-genuine spare parts and accessories for Toyota
vehicles are currently available in the market. You should know that Toyota
does not warrant these products and is not responsible for their
performance, repair, or replacement, or for any damage they may cause to,
or adverse effect they may have on, your Toyota vehicle.

This vehicle should not be modified with non-genuine Toyota products.
Modification with non-genuine Toyota products could affect its performance,
safety or durability, and may even violate governmental regulations. In
addition, damage or performance problems resulting from the modification
may not be covered under warranty.

27

Installation of a mobile two-way radio system

The installation of a mobile two-way radio system in your vehicle could affect
electronic systems such as:

● Multiport fuel injection system/sequential multiport fuel injection system

● Cruise control system

● Anti-lock brake system

● SRS airbag system

● Seat belt pretensioner system

Be sure to check with your Toyota dealer for precautionary measures or spe­cial instructions regarding installation of a mobile two-way radio system.

Scrapping your Toyota

The SRS airbag and seat belt pretensioner devices in your Toyota contain
explosive chemicals. If the vehicle is scrapped with the airbags and seat belt
pretensioners left as they are, this may cause an accident such as fire. Be
sure to have the systems of the SRS airbag and seat belt pretensioner
removed and disposed of by a qualified service shop or by your Toyota
dealer before you scrap your vehicle.

Perchlorate Material

Special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.

Your vehicle has components that may contain perchlorate. These compo­nents may include airbag, seat belt pretensioners, and wireless remote con­trol batteries.

28

Vehicle control and operation data recording

Your Toyota is equipped with sophisticated computers that record certain
information about your vehicle’s operation, such as:

• Engine speed

• Accelerator status

• Brake status

• Vehicle speed

• Shift position (except manual transmission)
The data recorded varies according to the grade level and options the vehi-

cle is equipped with. The computers do not record conversations, sound or
pictures.

● Data usage
Toyota may use the data recorded in these computers to diagnose malfunc-

tions, conduct research and development, and improve quality.
Toyota will not disclose the recorded data to a third party except:

• With the consent of the vehicle owner or with the consent of the lessee if
the vehicle is leased

• In response to an official request by the police, a court of law or a govern­ment agency

• For research purposes where the data is not tied to a specific vehicle or
vehicle owner

● Event data recorder

This vehicle is equipped with an event data recorder (EDR). The main pur­pose of an EDR is to record, in certain crash or near crash-like situations,
such as an air bag deployment or hitting a road obstacle, data that will assist
in understanding how a vehicle’s systems performed. The EDR is designed
to record data related to vehicle dynamics and safety systems for a short
period of time, typically 30 seconds or less.

The EDR in this vehicle is designed to record such data as:

• How various systems in your vehicle were operating;

• Whether or not the driver and passenger safety belts were buckled/fas­tened;

• How far (if at all) the driver was depressing the accelerator and/or brake
pedal; and,

• How fast the vehicle was traveling.

29

These data can help provide a better understanding of the circumstances in
which crashes and injuries occur.

NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situ­ation occurs; no data are recorded by the EDR under normal driving condi­tions and no personal data (e.g., name, gender, age, and crash location) are
recorded. However, other parties, such as law enforcement, could combine
the EDR data with the type of personally identifying data routinely acquired
during a crash investigation.
To read data recorded by an EDR, special equipment is required, and access
to the vehicle or the EDR is needed. In addition to the vehicle manufacturer,
other parties, such as law enforcement, that have the special equipment, can
read the information if they have access to the vehicle or the EDR.

● Disclosure of the EDR data
Toyota will not disclose the data recorded in an EDR to a third party except

when:

• An agreement from the vehicle’s owner (or the lessee for a leased vehicle)
is obtained

• Officially requested by the police or other authorities

• For use by Toyota in a lawsuit

• Ordered by a court of law

However, if necessary, Toyota will:

• Use the data for research on vehicle safety performance

• Disclose the data to a third party for research purposes without disclosing
information about the specific vehicle or vehicle owner

30

CAUTION

■ General precautions while driving

Driving under the influence: Never drive your vehicle when under the influ­ence of alcohol or drugs that have impaired your ability to operate your vehi­cle. Alcohol and certain drugs delay reaction time, impair judgment and
reduce coordination, which could lead to an accident that could result in
death or serious injury.

Defensive driving: Always drive defensively. Anticipate mistakes that other
drivers or pedestrians might make and be ready to avoid accidents.

Driver distraction: Always give your full attention to driving. Anything that dis­tracts the driver, such as adjusting controls, talking on a cellular phone or
reading can result in a collision with resulting death or serious injury to you,
your occupants or others.

■ General precaution regarding children’s safety

Never leave children unattended in the vehicle, and never allow children to
have or use the key.

Children may be able to start the vehicle or shift the vehicle into neutral.
There is also a danger that children may injure themselves by playing with
the windows, or other features of the vehicle. In addition, heat build-up or
extremely cold temperatures inside the vehicle can be fatal to children.

31

Symbols used throughout this manual

Cautions & Notices

CAUTION

This is a warning against anything which may cause injury to people if the
warning is ignored. You are informed about what you must or must not do in
order to reduce the risk of injury to yourself and others.

NOTICE

This is a warning against anything which may cause damage to the vehicle or
its equipment if the warning is ignored. You are informed about what you must
or must not do in order to avoid or reduce the risk of damage to your Toyota
and its equipment.

Symbols used in illustrations

The symbol of a circle with a slash through it means “Do not”, “Do
not do this”, or “Do not let this happen”.

32

Arrows indicating operations

Indicates the action (pushing, turning,
etc.) used to operate switches and
other devices.

Indicates the outcome of an operation
(e.g. a lid opens).

TABLE OF CONTENTS

1

Before driving

2

When driving

Interior and

3

exterior features

Maintenance

4

and care

When trouble

5

arises

Vehicle

6

specifications

Adjusting and operating features such as door locks,
mirrors, and steering column.

Driving, stopping and safe-driving information.

Air conditioning and audio systems, as well as other in­terior features for a comfortable driving experience.

Cleaning and protecting your vehicle, performing do-it­yourself maintenance, and maintenance information.

What to do if the vehicle needs to be towed, gets a flat
tire, or is involved in an accident.

Detailed vehicle information.

7

For owners

Index

Reporting safety defects for U.S. owners, seat belt and
SRS airbag instructions for Canadian owners and
camper information.

Alphabetical listing of information contained in this
manual.

1

1-1. Key information

Keys

The following keys are provided with the vehicle.

Vehicles without engine immobilizer system

Master keys
Key number plate

Vehicles with engine immobilizer system

Master keys
Key number plate

■ Key number plate

Keep the plate in a safe place such as your wallet, not in the vehicle. In the
event that a key is lost, a new key can be made by your Toyota dealer using
the key number plate. (→P. 534)

34

1-1. Key information

NOTICE

■ To prevent key damage (vehicles with engine immobilizer system)

● Do not subject the keys to strong shocks, expose them to high tempera-

tures by placing them in direct sunlight, or get them wet.

● Do not expose the keys to electromagnetic materials or attach any mate-

rial that blocks electromagnetic waves to the key surface.

1

Before driving

35

1-2. Opening, closing and locking the doors

Wireless remote control

The wireless remote control can be used to lock and unlock the vehi­cle from outside the vehicle.

∗

Locks all doors
Unlocks all doors
Pressing the button unlocks

the driver’s door. Pressing
the button again within 3
seconds unlocks the other
doors.

Sounds alarm
(push and hold)

■ Operation signals

A buzzer sounds and the emergency flashers flash to indicate that the doors
have been locked/unlocked. (Locked: Once; Unlocked: Twice)

■

Panic mode

When is pushed for longer than about
1 second, an alarm will sound for about
60 seconds and the vehicle lights will
flash to deter any person from trying to
break into or damage your vehicle.

To stop the alarm, push any button on the
wireless remote control.

■ Door lock buzzer

If a door is not fully closed, a buzzer sounds for 10 seconds if an attempt to
lock the door is made. Fully close the door to stop the buzzer, and lock the
vehicle once more.

∗: If equipped

36

1-2. Opening, closing and locking th e do o rs

■ Wireless remote control depletion

The standard battery life is 1 to 2 years. (The battery becomes depleted
even if the key is not used.) If the wireless remote control function does not
operate, the battery may be depleted. Replace the battery when necessary.
(→P. 472)

■ If the wireless remote control does not operate

Locking and unlocking the doors: Use the key. (→P. 39)

■ Security feature

If a door is not opened within approximately 30 seconds after the vehicle is
unlocked, the security feature automatically locks the vehicle again.

■ Conditions affecting operation

The wireless remote control function may not operate normally in the follow­ing situations.

● Near a TV tower, radio station, electric power plant, airport or other facil-

ity that generates strong radio waves

● When carrying a portable radio, cellular phone or other wireless commu-

nication device

● When multiple wireless keys are in the vicinity

● When the wireless key has come into contact with, or is covered by a

metallic object

● When a wireless key (that emits radio waves) is being used nearby

● When the wireless key has been left near an electrical appliance such as

a personal computer

■ When riding in an aircraft

When bringing a wireless remote control onto an aircraft, make sure you do
not press any buttons on the wireless remote control while inside the aircraft
cabin. If you are carrying a wireless remote control in your bag etc, ensure
that the buttons are not likely to be pressed accidentally. Pressing a button
may cause the wireless remote control to emit radio waves that could inter­fere with the operation of the aircraft.

■ Customization that can be configured at Toyota dealer

Settings (e.g. wireless remote control system) can be changed.
(Customizable features →P. 583)

1

Before driving

37

1-2. Opening, closing and locking the doors

■

Certification for wireless remote control
MODEL/FCC IDs:
Transmitter: GQ43VT20T
Receiver: GQ4-34R
IC (Canada) IDs:
Transmitter: 1470A-1T
Receiver: 1470A-6R
MADE IN U.S.A.

This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may
cause undesired operation.

WARNING:
Changes or modifications not expressively approved by the party responsi­ble for compliance could void the user’s authority to operate the equipment.

38

1-2. Opening, closing and locking the doors

Side doors

The vehicle can be locked/unlocked using the wireless remote con­trol, key or door lock switch.

■ Wireless remote control (if equipped)

→P. 36

1

■ Key

Regular Cab models

Access Cab and Double Cab models

Before driving

Locks the door
Unlocks the door

Locks all doors
Unlocks all doors

Turning the key a single time in
the driver’s door unlocks the
driver’s door, and turning the
key again unlocks the other
doors.

39

1-2. Opening, closing and locking the doors

■ Door lock switch (if equipped)

Driver’s door lock switch

Passenger’s door lock switch

Locks all doors
Unlocks all doors

Locks all doors
Unlocks all doors

■ Inside door lock button

40

Locks the door
Unlocks the door

Pulling the inside handle can
open the front door even if the
inside door lock button is in the
lock position.

1-2. Opening, closing and locking th e do o rs

Locking the front doors from the outside without a key

Move the inside door lock button to the lock position.

Close the door.
Vehicles with power door lock system
The door cannot be locked if a front door is o pen and the key is in

the engine switch.

Rear door child-protector lock (Double Cab models only)

The door cannot be opened from
inside the vehicle when the locks
are set.

These locks can be set to prevent
children from opening the rear
doors. Push down on each rear
door switch to lock both rear
doors.

1

Before driving

■ Key reminder buzzer

A buzzer sounds if the driver’s door is opened, while the engine switch is in
the ACC or LOCK position to remind you to remove the key.

41

1-2. Opening, closing and locking the doors

CAUTION

■ To prevent an accident

Observe the following precautions while driving the vehicle.
Failing to do so may result in a door opening and an occupant falling out,
resulting in death or serious injury.

● Always use a seat belt.

● Always lock all doors.

● Ensure that all doors are properly closed.

● Do not pull the inside handle of the doors while driving.

The doors may be opened and the passengers are thrown out of the vehi­cle and it may result in serious injury or death.
Be especially careful for the front doors, as the doors may be opened even
if the inside lock buttons are in locked position.

● Set the rear door child protector locks when children are seated in the rear

seat.

42

1-2. Opening, closing and locking the doors

Access doors (Access Cab models only)

The access door (rear door) can be opened using the inside handle.

Open the front door widely
Pull (from the outside) or

push (from the inside) the
inside handle of the access
door.

Open the access door

You can open and close the
access door only when the
front door is widely opened.

1

Before driving

NOTICE

■ When opening or closing the front door and access door

The front door and access door could be damaged if they hit each other
when being opened or closed.

43

1-2. Opening, closing and locking the doors

Tailgate

The tailgate can be opened.

Pull the handle
Open the tailgate slowly

The support cables will hold
the tailgate horizontal.

After closing the tailgate, try
pulling it toward you to make
sure it is securely locked.

Removing the tailgate

■ Before removing the tailgate (vehicles with rear view monitor

system)

These connector covers are used when removing the tailgate, to
prevent the back-up camera wire harness connectors from being
contaminated.

Connector cover (Gray)
Connector cover (White)

Store the connector covers in the
glove box in a plastic bag when
not using.

44

1-2. Opening, closing and locking th e do o rs

To disconnect the wire harness
connectors ( and ), press
and hold the lock of the tailgate
wire harness connector (White)
and pull apart.

1

Tailgate wire harness connec­tor (White)

Frame wire harness connector
(Gray)

Attach the connector cover
(white) to the frame wire harness
connector (Gray).

Connector cover (White)
Frame wire harness connector

(Gray)

Pull out the plastic wire protector
located in the vehicle bed by
pressing the tabs and pulling the
protector.

Be careful not to pull out all of the
tailgate wire harness. Failure to
do so may result in damage to
vehicle components.

Before driving

Plastic wire protector

Open the tailgate.

45

1-2. Opening, closing and locking the doors

■ Removing the tailgate

Pull out the wire harness from
the vehicle bed.

Attach the connector cover
(Gray) to the tailgate wire har­ness connector (White).

Tailgate wire harness connec­tor (White)

Connector cover (Gray)

46

Open the tailgate to the angle
where you can release the
brackets on the support cables
from the lugs on both sides.
Lift the support cable bracket up
and slide it off.

Support cable bracket

Tilt the tailgate to about 30° from
vertical and pull up the right side
of the tailgate to unhook the right
side.

Rear step bumper

1-2. Opening, closing and locking th e do o rs

Slide the tailgate a little to the
right to unhook the left side.

To attach the tailgate, follow the
removal procedure in reverse
order.

For rear end protection and eas­ier step-up loading.

To get on the rear step bumper,
use the shaded area in the illus­tration.

1

Before driving

CAUTION

■ Before removing the tailgate (vehicles with rear view monitor system)

Disconnect the wire harness between the back-up camera and the vehicle.
Failure to do so may result in serious injury or damage to the vehicle compo­nents.

■ Caution while driving

Observe the following precautions.
Failure to do so may result in death or serious injury.

● Do not drive with the tailgate open.

● Do not get on the rear step bumper.

47

1-2. Opening, closing and locking the doors

NOTICE

■ To prevent damage to the tailgate wire harness (vehicles with rear view

monitor system)

Do not pull out all of the tailgate wire harness before open the tailgate.

■ To prevent damage to the camera lens (vehicles with rear view monitor

system)

Store the removed tailgate with the back-up camera lens facing upward.

■ After closing the tailgate

Try pulling it toward you to make sure it is securely locked.

■ To prevent damage to the rear step bumper

Do not allow more than one person to get on the rear step bumper at a time.

48

1-3. Adjustable components (seats, mirrors, steering wheel)

Front seats

Bench type seat

Seat position adjustment
lever

1

Before driving

Separated type seats

Seat position adjustment
lever

Driver’s seat lumbar sup­port adjustment knob
(if equipped)

Seatback angle adjustment
lever

49

1-3. Adjustable components (seats, mirrors, steering wheel)

Moving passenger’s seat for rear seat entry (if equipped)

Lift the seatback angle adjusting
lever or press the pedal behind
the seatback. The seat will slide
forward.

Move the seat to the front-most
position.

■ After passengers are in the vehicle

Lift the seatback and return the seat until it locks.

Folding seatback (Bench type seat)

Pull the seatback lock release
lever and fold down the seat­back.
Hold the lever until you have
swung the seatback forward
slightly.

50

1-3. Adjustable components (seats, mirrors, steering wheel)

Folding passenger’s seat (vehicles with seatback table)

Pull the seatback angle adjusting
lever and raise the seatback to
its upright position.

Pull the seatback folding lever
and fold the seatback down.

1

Before driving

51

1-3. Adjustable components (seats, mirrors, steering wheel)

Active head restraints (Access Cab and Double Cab models only)

When the occupant’s back
presses against the seatback
during a rear-end collision, the
head restraint moves slightly for­ward to help reduce the risk of
whiplash on the seat occupant.

■ Active head restraints

Even small forces applied to the seatback may cause the head restraint to
move. Pushing up a locked head restraint forcibly may show the head
restraint inner structure. These do not indicate problems.

During
rear-end
collision

Inner
structure

■ Waterproof and water-repellent seats (if equipped)

Waterproof and water-repellent seats are installed in your vehicle; however,
the water-repellent effect does not last forever.

52

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■ Seat adjustment

● Be careful that the seat does not hit passengers or luggage.

● Do not recline the seat more than necessary when the vehicle is in motion

to reduce the risk of sliding under the lap belt.
If the seat is too reclined, the lap belt may slide past the hips and apply
restraint forces directly to the abdomen or your neck may contact the
shoulder belt, increasing the risk of death or serious injury in the event of
an accident.

● After adjusting the seat, make sure that the seat is locked in position.

■ After returning the seatback to the upright position

Observe the following precautions. Failure to do so may result in death or
serious injury.

● Make sure the seatback is securely locked.

● Check that the seat belts are not twisted or caught in the seatback.

● Arrange the seat belts in the proper positions for ready use.

■ Caution while driving

● Vehicles with seatback table: Do not sit on or place anything on the folded

seatback.

● Access Cab models only: Do not rest your foot on the press pedal behind

the passenger seat.

1

Before driving

53

1-3. Adjustable components (seats, mirrors, steering wheel)

Rear seats (Access Cab and Double Cab models)

Access Cab models

The bottom cushion of the rear seats can be raised and lowered.

■ Before raising the bottom cushion

Stow the seat belt buckles.

This prevents the seat belt
buckles from falling out when
you fold the seatback.

■ Raising the bottom cushion

Raise the bottom cushion up
while pulling the lever until it
locks.

■ Lowering the bottom cushion

54

Push the bottom cushion
down while pulling the lever
until the bottom cushion locks
into the seat position.

1-3. Adjustable components (seats, mirrors, steering wheel)

Double Cab models

The seatback of the rear seat can be folded.

■ Before folding rear seats

■ Folding rear seats

Stow the rear seat belt buck­les.

This prevents the seat belt
buckles from falling out when
you fold the seatback.

Pass the seat belts through
the seat belt hangers.

This prevents the shoulder belt
from being damaged.

Make sure that the seat belts
are removed from the hangers
before using them.

Remove the head restraint
Swing the bottom cushion

up by pulling the lock
release strap

1

Before driving

55

1-3. Adjustable components (seats, mirrors, steering wheel)

Attach the head restraints to
the holders located on the
back sides of the bottom cush­ions.

Fold down the seatback by
pulling the lock release strap.

■ Waterproof and water-repellent seats (if equipped)

Waterproof and water-repellent seats are installed in your vehicle; however,
the water-repellent effect does not last forever.

56

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■ When the seatback is folded/the bottom cushion is raised

Do not sit on or place anything on the seatback or auxiliary box while driving.

■ When returning the seats to their original position

Observe the following precautions. Failure to do so may result in death or
serious injury.

● Be careful not to get your hands or feet pinched in the seat.

● Make sure the seatbacks and bottom cushions are securely locked. Fail-

ure to do so will prevent the seat belt from operating properly.

● Check that the seat belts are not twisted or caught under the seat.

● Arrange the seat belts in the proper positions for ready use.

NOTICE

■ Before folding the seats

The seat belts buckles must be stowed.

1

Before driving

57

1-3. Adjustable components (seats, mirrors, steering wheel)

Head restraints

Head restraints are provided for all seats.

■ Adjusting the head restraints

Bench type front seat

Up

Pull the head restraints up.

Down

Push the head restraint down
while pushing the lock release
button.

Lock release button

Separated type front seat

Up

Pull the head restraints up.

Down

Lock release button

Rear seat (Double Cab models only)

Lock release button

58

Push the head restraint down
while pushing the lock release
button.

Up

Pull the head restraints up.

Down

Push the head restraint down
while pushing the lock release
button.

1-3. Adjustable components (seats, mirrors, steering wheel)

■ When using the rear head restraints

Access Cab models

Double Cab models

■ Removing the front head restraints

Bench type seat

To use

Lift up the head restraint until it
locks.

To fold

Pull the head restraint lock
release lever to fold the head
restraint.

To use

Lift up the head restraint until it
locks.

To fold

Pull the head restraint lock
release lever to fold the head
restraint.

1

Before driving

Pull the head restraint up while pushing
the lock release button.

59

1-3. Adjustable components (seats, mirrors, steering wheel)

Separated type seat

Pull the head restraint up while pushing
the lock release button.

■ Removing the rear head restraints (Double Cab models only)

Pull the head restraint up while pushing
the lock release button.

■ Installing the front head restraints

Bench type seat

Separated type seat

60

Align the head restraint with the installa­tion holes and push it down to the lock
position.

Press and hold the lock release button
when lowering the head restraint.

Align the head restraint with the installa­tion holes and push it down to the lock
position.

Press and hold the lock release button
when lowering the head restraint.

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Installing the rear head restraints (Double Cab models only)

Align the head restraint with the installa­tion holes and push it down to the lock
position.

Press and hold the lock release button
when lowering the head restraint.

■ When installed the rear outboard head restraints to opposite direction

(Double Cab models only)

Push a flathead screwdriver into the slot.
The slot is located on the left side of the
right head restraint anchor.

1

Before driving

While pressing in the screwdriver, pull up the head restraint.

■ Adjusting the height of the head restraints

Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.

■ Adjusting the front center seat (Bench type seat) and rear center seat

head restraints (Double Cab models)

Always raise the head restraint one level from the stowed position when
using.

61

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■ Head restraint precautions

Observe the following precautions regarding the head restraints. Failure to
do so may result in death or serious injury.

● Use the head restraints designed for each respective seat.

● Adjust the head restraints to the correct position at all times.

● After adjusting the head restraints, push down on them and make sure

they are locked in position.

● Do not drive with the head restraints removed.

62

1-3. Adjustable components (seats, mirrors, steering wheel)

Seat belts

Make sure that all occupants are wearing their seat belts before driv­ing the vehicle.

■ Correct use of the seat belts

● Extend the shoulder belt so

that it comes fully over the
shoulder, but does not
come into contact with the
neck or slide off the shoul­der.

● Position the lap belt as low
as possible over the hips.

● Adjust the position of the
seatback. Sit up straight
and well back in the seat.

● Do not twist the seat belt.

1

Before driving

■ Fastening and releasing the seat belt

Fastening the belt

Push the tab into the buckle
until a clicking sound is heard.

Releasing the belt

Press the release button.

Release
button

63

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Adjusting the height of the belt (front seats)

Up

Move the height adjuster up as
needed until you hear a click.

Down

Push the lock release button
and slide the height adjuster
down.

■ Center seat belt of the bench seat

Make sure the shoulder belt
pass through the guide when
using the center seat belt.

Seat belt pretensioners (front seats)

64

The pretensioner helps the seat
belt to quickly restrain the occu­pant by retracting the seat belt
when the vehicle is subjected to
certain types of severe frontal
collision or a vehicle rollover.

The pretensioner may not acti­vate in the event of a minor frontal
impact, a side impact or a rear
impact.

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Emergency locking retractor (ELR)

The retractor will lock the belt during a sudden stop or on impact. It may also
lock if you lean forward too quickly. A sl ow, easy motion will allow the belt to
extend so that you can move around fully.

■ Automatic locking retractor (ALR)

When a passenger’s shoulder belt is completely extended and then
retracted even slightly, the belt is locked in that position and cannot be
extended. This feature is used to hold the child restraint system (CRS) firmly .
To free the belt again, fully retract the belt and then pull the belt out once
more. (→P. 112)

■ Pregnant women

Obtain medical advice and wear the seat
belt in the proper way. (→P. 63)

Women who are pregnant should position
the lap belt as low as possible over the
hips in the same manner as other occu­pants. Extend the shoulder belt com­pletely over the shoulder and position the
belt across the chest. Avoid belt contact
over the rounding of the abdominal area.

If the seat belt is not worn properly, not
only a pregnant woman, but also the fetus
could suffer death or serious injury as a
result of sudden braking or a collision.

1

Before driving

■ People suffering illness

Obtain medical advice and wear the seat belt in the proper way.

■ Child seat belt usage

The seat belts of your vehicle were principally designed for persons of adult
size.

● Use a child restraint system appropriate for the child, until the child

become large enough to properly wear the vehicle’s seat belt. (→P. 108)

● When the child becomes large enough to properly wear the vehicle’s

seat belt, follow the instructions on P. 63 regarding seat belt usage.

65

1-3. Adjustable components (seats, mirrors, steering wheel)

■ Replacing the belt after the pretensioner has been activated

If the vehicle is involved in multiple collisions, the pretensioner will activate
for the first collision, but will not activate for the second or subsequent colli­sions.

■ Seat belt extender

If your seat belts cannot be fastened
securely because they are not long
enough, a personalized seat belt
extender is available from your Toyota
dealer free of charge.

CAUTION

Observe the following precautions to reduce the risk of injury in the event of
sudden braking, sudden swerving or an accident.
Failing to do so may cause death or severe injury.

■ Wearing a seat belt

● Ensure that all passengers wear a seat belt.

● Always wear a seat belt properly.

● Each seat belt should be used by one person only. Do not use a seat belt

for more than one person at once, including children.

● Toyota recommends that children be seated in the rear seat and always

use a seat belt and/or an appropriate child restraint system.

● Do not recline the seat any more than necessary to achieve a proper seat-

ing position. The seat belt is most effective when the occupants are sitting
up straight and well back in the seats.

● Do not wear the shoulder belt under your arm.

● Always wear your seat belt low and snug across your hips.

66

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■ When children are in the vehicle

Do not allow children to play with the seat belt. If the seat belt becomes
twisted around a child’s neck, it may lead to chocking or other serious inju­ries that could result in death. If this occurs and the buckle cannot be unfas­tened, scissors should be used to cut the belt.

■ Adjustable shoulder anchor

Always make sure the shoulder belt is positioned across the center of your
shoulder. The belt should be kept away from your neck, but not falling off
your shoulder. Failure to do so could reduce the amount of protection in an
accident and cause death or serious injuries in the event of a sudden stop,
sudden swerve or accident. (→P. 64)

■ Seat belt pretensioners

● Do not place anything, such as a cushion, on the front passenger’s seat.

Doing so will disperse the passenger’s weight, which prevents the sensor
from detecting the passenger’s weight properly. As a result, the seat belt
pretensioner for the front passenger’s seat may not activate in the event of
a collision.

● If the pretensioner has activated, the SRS warning light will come on. In

that case, the seat belt cannot be used again and must be replaced at
your Toyota dealer.

■ Seat belt damage and wear

● Do not damage the seat belts by allowing the belt, plate, or buckle to be

jammed in the door.

● Inspect the seat belt system periodically. Check for cuts, fraying, and loose

parts. Do not use a damaged seat belt until it is replaced. Damaged seat
belts cannot protect an occupant from death or serious injury.

● Ensure that the belt and tab are locked and the belt is not twisted.

If the seat belt does not function correctly, immediately contact your Toyota
dealer.

● Replace the seat assembly, including the belts, if your vehicle has been

involved in a serious accident, even if there is no obvious damage.

1

Before driving

67

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■ Seat belt damage and wear

● Do not attempt to install, remove, modify, disassemble or dispose of the

seat belts. Have any necessary repairs carried out by your Toyota dealer.
Inappropriate handling of the pretensioner may prevent it from operating
properly resulting in death or serious injury.

■ Using a seat belt extender

● Do not wear the seat belt extender, if you can fasten the seat belt without

the extender.

● Do not use the seat belt extender when installing a child restraint system,

because the belt will not securely hold the child restraint system, increas­ing the risk of death or serious injury in the event of an accident.

● The personalized extender may not be safe on another vehicle, when

used by another person, or at a different seating position other than the
one originally intended.

NOTICE

■ When using a seat belt extender

When releasing the seat belt, press on the buckle release button on the
extender, not on the seat belt.
This helps prevent damage to the vehicle interior and the extender itself.

68

1-3. Adjustable components (seats, mirrors, steering wheel)

Steering wheel

The steering wheel can be adjusted to a comfortable position.

Hold the steering wheel and
press the lever down.

Adjust to the ideal position by
moving the steering wheel
horizontally and vertically.

After adjustment, pull the lever
up to secure the steering
wheel.

1

Before driving

CAUTION

■ Caution while driving

Do not adjust the steering wheel while driving.
Doing so may cause the driver to mishandle the vehicle and an accident
may occur resulting in death or serious injury.

■ After adjusting the steering wheel

Make sure that the steering wheel is securely locked.
Otherwise, the steering wheel may move suddenly, possibly causing an
accident and resulting in death or serious injury.

69

1-3. Adjustable components (seats, mirrors, steering wheel)

Anti-glare inside rear view mirror

Glare from the headlights of vehicles behind can be reduced by
using the following functions.

Manual anti-glare inside rear view mirror

Normal position
Anti-glare position

70

1-3. Adjustable components (seats, mirrors, steering wheel)

Auto anti-glare inside rear view mirror (type A)
In automatic mode, sensors are used to detect the headlights of

vehicles behind and automatically reduces the reflected light.

Turns automatic mode on/off

The indicator comes on when
automatic mode is turned on.

The mirror will revert to the
automatic mode each time the
engine switch is turned on.

1

Before driving

71

1-3. Adjustable components (seats, mirrors, steering wheel)

Auto anti-glare inside rear view mirror (type B)
In automatic mode, sensors are used to detect the headlights of

vehicles behind and automatically reduces the reflected light.

Turns automatic mode on/off

The indicator comes on when
automatic mode is turned on.

The mirror will revert to the
automatic mode each time the
engine switch is turned on.

Adjusting the height of rear view mirror

Adjust the height of the rear view
mirror by moving it up and down.

72

1-3. Adjustable components (seats, mirrors, steering wheel)

Inside rear view mirror display (vehicles with auto anti-glare
inside rear view mirror)

The inside rear view mirror displays the following information.
Also, the display and display settings can be changed.

1

■ Compass

→P. 409

■ Outside temperature display

→P. 376

■ Rear view monitor system

→P. 178

■ Garage door opener

→P. 400

■ To prevent sensor error (vehicles with auto anti-glare inside rear view

mirror)

To ensure that the sensors operate prop­erly, do not touch or cover them.

■ Customization that can be configured for the inside rear view mirror

display (vehicles with auto anti-glare inside rear view mirror)

Settings (e.g. language) can be changed.
(Customizable features →P. 583)

Before driving

73

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■ Caution while driving

Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and an accident, resulting in
death or serious injury.

74

1-3. Adjustable components (seats, mirrors, steering wheel)

Outside rear view mirrors

Mirror angle can be adjusted.

Power-adjustable type

Select a mirror to adjust.
(L: left or R: right)

1

Adjust the mirror up, down,
in or out using the switch.

Before driving

75

1-3. Adjustable components (seats, mirrors, steering wheel)

Manually adjustable type

Adjust the mirror up, down, in
or out by pushing the mirror
surface.

Folding back the mirrors

Push backward to fold the mir­rors.

■ Mirror operating conditions (vehicles with power-adjustable type only)

The engine switch is in the ACC or ON position.

76

1-3. Adjustable components (seats, mirrors, steering wheel)

CAUTION

■ When driving the vehicle

Observe the following precautions while driving.
Failing to do so may result in loss of control of the vehicle and cause an acci­dent, resulting in death or serious injury.

● Do not adjust the mirrors while driving.

● Do not drive with the mirrors folded back.

● Both the driver and passenger side mirrors must be extended and properly

adjusted before driving.

NOTICE

■ If ice should jam the mirror

Do not operate the control or scrape the mirror face. Use a spray de-icer to
free the mirror.

1

Before driving

77

1-4. Opening and closing the windows

Power windows

The power windows can be opened/closed using the following
switches.

Driver’s power window switches

Front and rear passenger’s power window switch

∗

Closing
Opening
One-touch opening (driver ’s

window only)

*: Pressing the switch in the

opposite direction will stop win­dow travel partway.

Closing
Opening

*

Lock switch

78

Press the switch down to lock
passenger window switches.

Use this switch to prevent chil­dren from accidentally opening or
closing a passenger window.

∗: If equipped

1-4. Opening and closing the windows

■ The power windows can be operated when

The engine switch is in the ON position.

■ Operating the power windows after turning the engine off

The power windows can be operated for approximately 43 seconds even
after the engine switch is turned to the ACC or LOCK position. They cannot,
however, be operated once either front door is opened.

CAUTION

■ Closing the windows

Observe the following precautions.
Failing to do so may result in death or serious injury.

● Check to make sure that all passengers do not have any part of their body

in a position where it could be caught when a window is being operated.

● Do not allow children to operate the power windows.

Closing a power window on someone can cause serious injury, and in
some instances, even death.

1

Before driving

79

1-4. Opening and closing the windows

Back window (vehicles with sliding type)

The back window can be opened and closed using the lock release
lever.

Open/close

Push the lock release lever
and slide the back window.

■ Closing the back window

Make sure that the back window is securely closed after closing it.

CAUTION

■ While driving

Keep the back window closed.
This not only keeps personal belongings from being thrown out, but also pre­vents exhaust gases from entering the vehicle.

80

1-5. Refueling

Opening the fuel tank cap

Perform the following steps to open the fuel tank cap.

■ Before refueling the vehicle

Turn the engine switch off and ensure that all the doors and win­dows are closed.

1

■ Opening the fuel tank cap

Before driving

Open the fuel filler door.

Turn the fuel tank cap slowly
to open.

81

1-5. Refueling

Closing the fuel tank cap

When replacing the fuel tank
cap, turn it until a clicking sound
is heard.

After releasing your hand, the cap
will turn slightly to the opposite
direction.

■ Fuel types

Use unleaded gasoline. (Octane Rating 87 [Research Octane Number 91] or
higher)

■ Fuel tank capacity

Approximately 21.1 gal. (80.0 L, 17.6 Imp.gal.)

CAUTION

■ Refueling the vehicle

Observe the following precautions while refueling the vehicle.
Failure to do so, may result in death or serious injury.

● Touch the vehicle or some other metal surface to discharge any static

electricity.
Sparks resulting from discharging static electricity may cause the fuel
vapors to ignite.

● Always hold the grips on the fuel tank cap and turn it slowly to remove it.

A whooshing sound may be heard when the fuel tank cap is loosened.
Wait until the sound cannot be heard before fully removing the cap.
In hot weather, pressurized fuel may spray out of the filler neck and cause
injury.

● Do not allow anyone that has not discharged static electricity from their

bodies to come close to an open fuel tank.

82

1-5. Refueling

CAUTION

■ Refueling the vehicle

● Do not inhale vaporized fuel.

Fuel contains substances that are harmful if inhaled.

● Do not smoke while refueling the vehicle.

Doing so may cause the fuel to ignite and cause a fire.

● Do not return to the vehicle or touch any person or object that is statically

charged.
This may cause static electricity to build up, resulting in a possible engine
hazard.

■ When replacing the fuel tank cap

Do not use anything but a genuine Toyota fuel tank cap designed for your
vehicle. Doing so may cause a fire or other incident which may result in
death or serious injury.

NOTICE

1

Before driving

■ Refueling

Do not spill fuel during refueling.
Doing so may damage the vehicle, such as causing the exhaust systems to
operate abnormally or damaging fuel system components or the vehicle’s
painted surface.

■ To prevent damage to the fuel filler door

Do not apply excessive force.

83

1-6. Theft deterrent system

Engine immobilizer system

The vehicle’s keys have built-in transponder chips that prevent the
engine from starting if the key has not been previously registered in
the vehicle’s on-board computer.

Never leave the keys inside the vehicle when you leave the vehicle.

∗

The indicator light flashes after
the key has been removed
from the engine switch to indi­cate that the system is operat­ing.

The indicator light stops flash­ing after the registered key
has been inserted into the
engine switch to indicate that
the system has been can­celed.

■ System maintenance

The vehicle has a maintenance-free type engine immobilizer system.

■ Conditions that may cause the system to malfunction

● If the key is in contact with a metallic object

● If the key is in close proximity to or touching a key to the security system

(key with a built-in transponder chip) of another vehicle

∗: If equipped

84

1-6. Theft deterrent system

■ Certifications for the engine immobilizer system

For vehicles sold in U.S.A.
FCC ID: MOZRI-21BTY
This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

FCC WARNING:
Changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

For vehicles sold in Canada
This device complies with RSS-210 of Industry Canada. Operation is subject

to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.

1

Before driving

85

1-6. Theft deterrent system

For vehicles sold in New Caledonia

“Hereby, Tokai Rika Co., Ltd., declares that this Immobilizer,
model RI-21BTY, is in compliance with the essential require­ments and other relevant provisions of Directive 1999/5/EC.”

NOTICE

■ To ensure the system operates correctly

Do not modify or remove the system. If modified or removed, the proper
operation of the system cannot be guaranteed.

86

1-7. Safety information

Correct driving posture

Drive in a good posture as follows:

Sit upright and well back in
the seat. (→P. 49)

Adjust the position of the
seat forward or backward to
ensure the pedals can be
reached and easily
depressed to the extent
required. (→P. 49)

Adjust the seatback so that
the controls are easily oper­able.

Adjust the tilt and telescopic
positions of the steering
wheel downward so the air­bag is facing your chest.
(→P. 69)

Lock the head restraint in
place with the center of the
head restraint closest to the
top of your ears. (→P. 58)

Wear the seat belt correctly.
(→P. 63)

1

Before driving

87

1-7. Safety information

CAUTION

■ While driving

● Do not adjust the position of the driver’s seat while driving.

Doing so could cause the driver to lose control of the vehicle.

● Do not place a cushion between the driver or passenger and the seatback.

A cushion may prevent correct posture from being achieved, and reduce
the effectiveness of the seat belt and head restraint, increasing the risk of
death or serious injury to the driver or passenger.

● Do not place anything under the front seats.

Objects placed under the front seats may become jammed in the seat
tracks and stop the seat from locking in place. This may lead to an acci­dent. The adjustment mechanism may also be damaged.

■ Adjusting the seat position

● Take care when adjusting the seat position to ensure that other passen-

gers are not injured by the moving seat.

● Do not put your hands under the seat or near the moving parts to avoid

injury.
Fingers or hands may become jammed in the seat mechanism.

88

1-7. Safety information

SRS airbags

The SRS airbags inflate when the vehicle is subjected to certain
types of severe impacts that may cause significant injury to the
occupants. They work together with the seat belts to help reduce the
risk of death or serious injury.

1

Before driving

Front airbags

Driver airbag/front passenger airbag

Can help protect the head and chest of the driver and right front

passenger from impact with interior components.

Side and curtain shield airbags

Side airbags

Can help protect the torso of the front seat occupants.

Curtain shield airbags

Can help protect primarily the head of outside occupants.

89

1-7. Safety information

Airbag system components

Vehi cles with bench type front seat

Vehi cles with separated type front seat

90

1-7. Safety information

Front passenger airbag
Curtain shield airbags
Side airbags
AIR BAG ON and AIR BAG

OFF indicator lights
SRS warning light and

RSCA OFF indicator light
Driver airbag
RSCA OFF switch

(4WD models only)
Curtain shield airbag sen-

sors (Access Cab and Dou­ble Cab models)

Driver’s seat position sen­sor

Driver’s seat belt buckle
switch

Front passenger’s seat belt
buckle switch

Occupant detection system
(ECU and sensors)

Airbag sensor assembly
Front airbag sensors
Front passenger’s seat

position sensor
Belt tension sensor

Side and curtain shield air­bag sensors

Your vehicle is equipped with ADVANCED AIRBAGS designed based
on US motor vehicle safety standards (FMVSS208). The airbag sys­tem controls airbag deployment power for the driver and right front
passenger. The driver airbag system consists of the driver seat’s
position sensor etc. The front passenger ’s airbag system consists of
the front passenger occupant classification sensor etc.

1

Before driving

The main SRS airbag system components are shown above. The
SRS airbag system is controlled by the airbag sensor assembly. The
airbag sensor assembly consists of a safing sensor and an airbag
sensor.

Bench type front seat: The SRS airbags are designed to protect the
driver and right front passenger, and they are not designed to protect
an occupant in the front center seating position.

91

1-7. Safety information

In certain types of severe frontal or side impacts, the SRS airbag sys­tem triggers the airbag inflators. A chemical reaction in the inflators
quickly fills the airbags with non-toxic gas to help restrain the motion
of the occupants.

■ SRS warning light

This warning light system monitors the airbag sensor assembly, front airbag
sensors, side and curtain shield airbag sensor assemblies, curtain shield air­bag sensor assemblies (Access Cab and Double cab models), driver’s seat
position sensor, driver’s seat belt buckle switch, front passenger occupant
classification system, AIR BAG ON and AIR BAG OFF indicator lights, front
passenger’s seat position sensor (Bench type seat), front passenger’s seat
belt buckle switch, front seat belt pretensioner assemblies, belt tension sen­sor (Bench type seat), RSCA OFF indicator light, inflators, interconnecting
wiring and power sources. (→P. 506)

■ If the SRS airbags deploy (inflate)

● Bruising and slight abrasions may result from contact with a deploying

(inflating) SRS airbag.

● A loud noise and white powder will be emitted.

● Parts of the airbag module (steering wheel hub, airbag cover and inflator)

as well as the front seats, and parts of the front and rear pillars and roof
side rail, may be hot for several minutes. The airbag itself may also be
hot.

● The front windshield may crack.

■ Operating conditions (front airbags)

● The SRS front airbag will deploy in the event of an impact that exceeds

the set threshold level (the level of force corresponding to an approxi­mately 12-18 mph [20-30 km/h] frontal collision with a fixed wall that does
not move or deform).

However, this threshold velocity will be considerably higher if the vehicle
strikes an object, such as a parked vehicle or sign pole, which can move or
deform on impact, or if the vehicle is involved in an underride collision (e.g.
a collision in which the front of the vehicle “underrides”, or goes under, the
bed of a truck, etc.).

92

1-7. Safety information

● It is possible that in some collisions where the forward deceleration of the

vehicle is very close to the designed threshold level, the SRS front air­bags and the seat belt pretensioners may not activate together.

● The SRS front passenger airbag will not activate if there is no passenger

sitting in the front passenger seat. However, the front passenger airbag
may deploy if luggage is put in the seat, or the seat belt is fastened, even
if the seat is unoccupied. (→P. 103)

■ Operating conditions (side airbags and curtain shield airbags)

The SRS side airbags and SRS curtain shield airbags will deploy in the
event of an impact that exceeds the set threshold level (the level of force
corresponding to the impact force produced by an approximately 3307 lb.
[1500 kg] vehicle colliding with the vehicle cabin from a direction perpendicu­lar to the vehicle orientation at an approximate speed of 12-18 mph [20-30
km/h]).

■ Operating conditions (side airbags)

The SRS side airbag on the passenger seat will activate even if there is no
passenger sitting in the right front passenger seat. (→P. 103)

■ Operating conditions (curtain shield airbags)

The SRS curtain shield airbags are designed to inflate when the passenger
compartment is subjected to a severe impact from the side or vehicle roll­over.

■ Conditions under which the SRS airbags may deploy (inflate), other

than a collision

The SRS front airbags may also deploy if a serious impact occurs to the
underside of your vehicle. Some examples are shown in the illustration.

1

Before driving

● Hitting a curb, edge of pavement or

hard surface

● Falling into or jumping over a deep hole

● Landing hard or vehicle falling

93

1-7. Safety information

The SRS curtain shield airbags may also deploy under the situation shown
in the illustration.

● The angle of vehicle tip-up is marginal.

● The vehicle skids and hits a curb stone.

■ Types of collisions that may not deploy the SRS airbag (front airbags)

The SRS front airbags are generally not designed to inflate if the vehicle is
involved in a side or rear collision, if it rolls over, or if it is involved in a low­speed frontal collision. But, whenever a collision of any type causes suffi­cient forward deceleration of the vehicle, deployment of the SRS front air­bags may occur.

● Collision from the side

● Collision from the rear

● Vehicle rollover

94

1-7. Safety information

■ Types of collisions that may not deploy the SRS airbag

(side airbags and curtain shield airbags)

The SRS side airbag and curtain shield airbag system may not activate if the
vehicle is subjected to a collision from the side at certain angles, or a colli­sion to the side of the vehicle body other than the passenger compartment.

1

● Collision from the side to the vehicle

body other than the passenger com­partment

● Collision from the side at an angle

The SRS side airbags are not generally designed to inflate if the vehicle is
involved in a frontal or rear collision, if it rolls over, or if it is involved in a low­speed side collision.

● Collision from the front

● Collision from the rear

● Vehicle rollover

The SRS curtain shield airbags are not generally designed to inflate if the
vehicle is involved in a frontal or rear collision, if it pitches end over end, or if
it is involved in a low-speed side collision.

● Collision from the front

● Collision from the rear

● Pitching end over end

Before driving

95

1-7. Safety information

■ When to contact your Toyota dealer

In the following cases, contact your Toyota dealer as soon as possible.

● Any of the SRS airbags have been inflated.

● The front of the vehicle is damaged or

deformed, or was involved in an acci­dent that was not severe enough to
cause the SRS airbags to inflate.

● A portion of a door is damaged or

deformed, or the vehicle was involved
in an accident that was not severe
enough to cause the SRS side airbags
and curtain shield airbags to inflate.

● The pad section of the steering wheel

or dashboard near the front passenger
airbag is scratched, cracked, or other­wise damaged.

96

● The surface of the seats with the side

airbag is scratched, cracked or other­wise damaged.

● The portion of the front pillars, rear pil-

lars or roof side rail garnishes (padding)
containing the curtain shield airbags
inside is scratched, cracked or other­wise damaged.

1-7. Safety information

CAUTION

■ SRS airbag precautions

Observe the following precautions regarding the airbags.
Failure to do so may cause death or serious injury.

● The driver and all passengers in the vehicle must wear their seat belts

properly.
The SRS airbags are supplemental devices to be used with the seat belts.

● The SRS driver airbag deploys with considerable force, and can cause

death or serious injury especially if the driver is very close to the airbag.
The National Highway Traffic Safety Administration (“NHTSA”) advises:

Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm)
of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro­vides you with a clear margin of safety . This distance is measured from the
center of the steering wheel to your breastbone. If you now sit less than 10
in. (250 mm) away, you can change your driving position in several ways:

• Move your seat to the rear as far as you can while still reaching the
pedals comfortably.

• Slightly recline the back of the seat.
Although vehicle designs vary, many drivers can achieve the 10 in.
(250 mm) distance, even with the driver seat all the way forward, sim­ply by reclining the back of the seat somewhat. If reclining the back of
your seat makes it hard to see the road, raise yourself by using a firm,
non-slippery cushion, or raise the seat if your vehicle has that feature.

• If your steering wheel is adjustable, tilt it downward. This points the air­bag toward your chest instead of your head and neck.

1

Before driving

97

1-7. Safety information

CAUTION

■ SRS airbag precautions

The seat should be adjusted as recommended by NHTSA above, while still
maintaining control of the foot pedals and steering wheel, and your view of
the instrument panel controls.

● If the seat belt extender has been con-

nected to the driver’s seat belt buckle
but the seat belt extender has not also
been fastened to the latch plate of the
driver’s seat belt, the SRS driver’s air­bag system will judge that the driver is
wearing the seat belt even though the
seat belt has not been connected. In
this case, the driver’s airbag may not
activate correctly in a collision, resulting
in death or serious injury in the event of
collision. Be sure to wear the seat belt
with the seat belt extender.

● The SRS front passenger airbag also deploys with considerable force, and

can cause death or serious injury especially if the front passenger is very
close to the airbag. The front passenger seat should be as far from the air­bag as possible with the seatback adjusted, so the front passenger sits
upright.

● Improperly seated and/or restrained infants and children can be killed or

seriously injured by a deploying airbag. An infant or child who is too small
to use a seat belt should be properly secured using a child restraint sys­tem. Toyota strongly recommends that all infants and children be placed in
the rear seats of the vehicle and properly restrained. The rear seats are
the safest for infants and children. (→P. 108)

98

CAUTION

■ SRS airbag precautions

1-7. Safety information

● Do not sit on the edge of the seat or

lean against the dashboard.

● Do not allow a child to stand in front of

the SRS front passenger airbag unit or
sit on the knees of a front passenger.

● Do not drive the vehicle while the driver

or passenger has items resting on their
knees.

● Do not lean against the door, the roof

side rail or the front, side and rear pil­lars.

● Do not allow anyone to kneel on the

passenger seat toward the door or put
their head or hands outside the vehicle.

1

Before driving

99

1-7. Safety information

CAUTION

■ SRS airbag precautions

● Do not attach anything to or lean any-

thing against areas such as the dash­board or steering wheel pad.
These items can become projectiles
when SRS driver and front passenger
airbags deploy.

● Do not attach anything to areas such as

the door, windshield glass, side door
glass, front and rear pillars, roof side
rail or assist grip.

● Do not hang coat hangers or other hard

objects on the coat hooks. All of these
items could become projectiles and
seriously injure or kill you, should the
SRS curtain shield airbag deploy.

● Bench type front seat: Do not use a seat accessory, such as a cushion or

seat cover, that covers the seat cushion surface.

● Do not use seat accessories which cover the parts where the SRS side

airbags inflate as they may interfere with inflation of the airbags.

● Do not strike or apply significant levels of force to the area of the SRS air-

bag components (→P. 90).
Doing so can cause the SRS airbags to malfunction.

● Do not touch any of the component parts immediately after the SRS air-

bags have deployed (inflated) as they may be hot.

● If breathing becomes difficult after the SRS airbag has deployed, open a

door or window to allow fresh air in, or leave the vehicle if it is safe to do
so. Wash off any residue as soon as possible to prevent skin irritation.

● If the areas where the SRS airbags are stored, such as the steering wheel

pad and front and rear pillar garnishes, are damaged or cracked, have
them replaced by your Toyota dealer.

100

1-7. Safety information

CAUTION

■ Modification and disposal of SRS airbag system components

Do not dispose of your vehicle or perform any of the following modifications
without consulting your Toyota dealer.
The SRS airbags may malfunction or deploy (inflate) accidentally, causing
death or serious injury.

● Installation, removal, disassembly and repair of the SRS airbags.

● Repairs, modifications, removal or replacement of the steering wheel,

instrument panel, dashboard, seats or seat upholstery, front, side and rear
pillars or roof side rails.

● Repairs or modifications of the front fender, front bumper, or side of the

occupant compartment.

● Installation of snow plows, winches, etc. to the front grille (bull bars, kan-

garoo bar etc.).

● Modifications to the vehicle’s suspension system.

● Do not use tires or wheels other than the manufacturer ’s recommended

size. (→P. 564)

● Installation of electronic devices such as mobile two-way radios or CD

players.

● Modifications to your vehicle for a person with a physical disability.

1

Before driving

101

1-7. Safety information

Deactivating the curt ain shield airb ags in a vehicle rollover (4WD models only)

On/off (hold for a few seconds)

The RSCA OFF indicator turns on
(only when the engine switch is in
the ON position.)

The roll sensing function for the
curtain shield airbags and seat
belt pretensioners will turn back
on automatically each time the
engine switch is turned on.

■ The switch only should be used

In a situation where inflation is not desired (such as during extreme off-road
driving).

■ Operating conditions when the RSCA OFF indicator is on

● The curtain shield airbag and seat belt pretensioner will not activate in a

vehicle rollover.

● The curtain shield airbag will activate in a severe side impact.

CAUTION

■ For normal driving

Make sure the RSCA OFF indicator is not turned on. If it is left on, the curtain
shield airbag will not activate in the event of an accident, which may result in
death or serious injury.

102

1-7. Safety information

Front passenger occupant classification system

Your vehicle is equipped with a front passenger occupant classifica­tion system. This system detects the conditions of the right front
passenger seat and activates or deactivates the devices for the front
passenger.

1

Before driving

SRS warning light
Front passenger’s seat belt reminder light
AIR BAG OFF indicator light
AIR BAG ON indicator light

103

1-7. Safety information

Conditions and operation of the front passenger occupant
classification system

■ Adult*

1

AIR BAG ON and AIR BAG OFF indica-

tor lights

Indicator/

warning light

SRS warning light Off

Front passenger’s seat belt reminder

light

Front passenger airbag

Side airbag on the front passenger seat

Devices

Curtain shield airbag in the front passen-

ger side

Front passenger’s seat belt pretensioner

■ Child*3 or child restraint system*

AIR BAG ON and AIR BAG OFF indica-

tor lights

Indicator/

warning light

Front passenger’s seat belt reminder

SRS warning light Off

light

Front passenger airbag Deactivated

AIR BAG ON

Flashing*

2

Activated

4

AIR BAG

5

OFF*

Flashing*

2

104

Devices

Side airbag on the front passenger seat

Curtain shield airbag in the front passen-

ger side

Front passenger’s seat belt pretensioner

Activated

■ Unoccupied

1-7. Safety information

AIR BAG ON and AIR BAG OFF indica-

tor lights

Indicator/

warning light

Devices

Front passenger’s seat belt reminder

Side airbag on the front passenger seat

Curtain shield airbag in the front passen-

Front passenger’s seat belt pretensioner Deactivated

SRS warning light

light

Front passenger airbag Deactivated

ger side

■ There is a malfunction in the system

AIR BAG ON and AIR BAG OFF indica-

tor lights

Indicator/

warning light

Devices

Front passenger’s seat belt reminder

Side airbag on the front passenger seat

Curtain shield airbag in the front passen-

SRS warning light On

light

Front passenger airbag Deactivated

ger side

Not illumi-

nated

1

Off

Before driving

Activated

AIR BAG

OFF

Off

Activated

Front passenger’s seat belt pretensioner

1

*

: The system judges a person of adult size as a n adult. When a

smaller adult sits in the front passenger seat, the system may rec­ognize him/her as a child depending on his/her physique and pos­ture.

2

*

: In the event the front passenger does not wear a seat belt.

3

: When a larger child who has outgrown a child restraint system

*

sits in the front passenger seat, the system may recognize him/
her as an adult depending on his/her physique or posture.

105

1-7. Safety information

*4: Never install a rear-facing child restraint system on the front pas-

senger seat. A forward-facing child restraint system should only
be installed on the front passenger seat when it is unavoidable.
(→P. 108)

5

*

: In case the indicator is not illuminated, consult this manual for

installing the child restraint system properly. (→P. 112)

*

CAUTION

■ Front passenger occupant classification system precautions

Observe the following precautions regarding front passenger occupant clas­sification system.
Failure to do so may cause death or serious injury.

● Wear the seat belt properly.

● Make sure the front passenger’s seat belt tab has not been left inserted

into the buckle before someone sits in the front passenger seat.

● Make sure the AIR BAG OFF indicator light is not illuminated when using

the seat belt extender for the front passenger seat. If the AIR BAG OFF
indicator light is illuminated, disconnect the extender tongue from the seat
belt buckle, then reconnect the seat belt. Reconnect the seat belt extender
after making sure the AIR BAG ON indicator light is illuminated. If you use
the seat belt extender while the AIR BAG OFF indicator light is illuminated,
the front passenger airbag may not activate correctly, which could cause
death or serious injury in the event of collision.

● Do not place a heavy load on the front passenger seat or equipment (e.g.

seatback table).

● Do not apply pressure to the front passenger seat by resting hands or legs

on the seatback.

● Do not let a rear passenger lift the front passenger seat with their feet or

press on the seatback with their legs.

● Do not put objects under the front passenger seat.

106

1-7. Safety information

CAUTION

■ Front passenger occupant classification system precautions

● Do not recline the front passenger seatback so far that it touches a rear

seat or a back wall. This may cause the AIR BAG OFF indicator light to be
illuminated, which indicates that the passenger’s airbags will not deploy in
the event of a severe accident. If the seatback touches the rear seat or
back wall, return the seatback to a position where it does not touch the
rear seat or back wall. Keep the front passenger seatback as upright as
possible when the vehicle is moving. Reclining the seatback excessively
may lessen the effectiveness of the seat belt system.

● If an adult sits in the front passenger seat, the AIR BAG ON indicator light

is illuminated. If the AIR BAG OFF indicator is illuminated, ask the passen­ger to sit up straight, well back in the seat, feet on the floor, and with the
seat belt worn correctly. If the AIR BAG OFF indicator still remains illumi­nated, either ask the passenger to move to the rear seat, or if that is not
possible, move the front passenger seat fully rearward.

● When it is unavoidable to install the forward-facing child restraint system

on the front passenger seat, install the child restraint system on the front
passenger seat in the proper order. (→P. 112)

● Do not modify or remove the front seats.

● Do not kick the front passenger seat or subject it to severe impact. Other-

wise, the SRS warning light may come on to indicate a malfunction of the
detection system. In this case, contact your Toyota dealer immediately.

● Child restraint systems installed on the rear seat should not contact the

front seatbacks.

● Do not use a seat accessory, such as a cushion or seat cover, that covers

the seat cushion surface.

● Access Cab and Double Cab models: Do not attach a commercial seat-

back table or other heavy item to the back of the front passenger seat.

● Do not modify or replace the upholstery of the front seat.

1

Before driving

107

1-7. Safety information

Child restraint systems

A child restraint system for a small child or baby must itself be pro p­erly restrained on the seat with the lap portion of the lap/shoulder
belt.

The laws of all 50 states of the U.S.A. and Canada now require the
use of child restraint systems.

Points to remember

Studies have shown that installing a child restraint on a rear seat is
much safer than installing one to the front passenger seat.

● Choose a child restraint system that suits your vehicle and is
appropriate to the age and size of the child.

● For installation details, follow the instructions provided with the
child restraint system.
General installation instructions are provided in this manual.
(→P. 112)

Types of child restraints

Child restraint systems are classified into the following 3 types
according to the age and size of the child.

Rear facing — Infant seat/convertible seat (Access Cab and Dou­ble Cab models only)

108

Forward facing — Convertible seat

Booster seat

1-7. Safety information

1

Before driving

■ Selecting an appropriate child restraint system

● Use a child restraint system appropriate for the child until the child

becomes large enough to properly wear the vehicle’s seat belt.

● If a child is too large for a child restraint system, sit the child on a rear

seat and use the vehicle’s seat belt. (→P. 63)

109

1-7. Safety information

CAUTION

■ Child restraint precautions

● For effective protection in automobile accidents and sudden stops, a child

must be properly restrained, using a seat belt or child restraint system
depending on the age and size of the child. Holding a child in your arms is
not a substitute for a child restraint system. In an accident, the child can be
crushed against the windshield, or between you and the vehicle’s interior.

● Regular Cab models: Toyota strongly urges use of a proper child restraint

system which conforms to the size of the child.

● Access Cab and Double Cab models: Toyota strongly urges the use of a

proper child restraint system that conforms to the size of the child, installed
on the rear seat. According to accident statistics, the child is safer when
properly restrained in the rear seat than in the front seat.

● Never install a rear-facing child restraint system on the front passenger

seat even if the AIR BAG OFF indicator light is illuminated. In the event of
an accident, the force of the rapid inflation of the front passenger airbag
can cause death or serious injury to the child if the rear-facing child
restraint system is installed on the front passenger seat.

● Access Cab and Double Cab models: A forward-facing child restraint sys-

tem may be installed on the front passenger seat only when it is unavoid­able. A child restraint system that requires a top tether strap should not be
used in the front passenger seat since there is no top tether strap anchor
for the front passenger seat. Adjust the seatback as upright as possible
and always move the seat as far back as possible even if AIR BAG OFF
indicator light is illuminated, because the front passenger airbag could
inflate with considerable speed and force. Otherwise, the child may be
killed or seriously injured.

● Bench type front seat: Do not install a child restraint system on the center

seat if it interferes with driving operations such as gear shifting. In this
case, install the child restraint system on the right passenger seat.

● Bench type front seat: The driver and passengers sit on a bench seat in

this vehicle. Therefore, when installing a child restraint system, the seat
must be moved back from the SRS airbag as far as possible while also
maintaining the driver’s seating position. Otherwise, the force of the rapid
inflation of the airbag could cause death or serious injury to the child.

110

1-7. Safety information

CAUTION

■ Child restraint precautions

● Do not use the seat belt extender when installing a child restraint system

on the front or rear passenger seat. If installing a child restraint system
with the seat belt extender connected to the seat belt, the seat belt will not
securely hold the child restraint system, which could cause death or seri­ous injury to the child or other passengers in the event of a sudden stop,
sudden swerve or an accident.

● Do not allow the child to lean his/her head or any part of his/her body

against the door or the area of the seat, front and rear pillars or roof side
rail from which the side airbags or curtain shield airbags deploy even if the
child is seated in the child restraint system. It is dangerous if the side air­bags and curtain shield airbags inflate, and the force of the rapid inflation
could cause death or serious injury to the child.

● Make sure you have complied with all installation instructions provided by

the child restraint manufacturer and that the system is properly secured. If
it is not secured properly, it may cause death or serious injury to the child
in the event of a sudden stop, sudden swerve or an accident.

■ When children are in the vehicle

Do not allow children to play with the seat belt. If the seat belt becomes
twisted around a child’s neck, it may lead to choking or other serious injuries
that could result in death. If this occurs and the buckle cannot be unfas­tened, scissors should be used to cut the belt.

■ When the child restraint system is not in use

● Keep the child restraint system properly secured on the seat even if it is

not in use. Do not store the restraint unsecured in the passenger compart­ment.

● If it is necessary to detach the child restraint system, remove it from the

vehicle. This will prevent it from injuring passengers in the event of a sud­den stop, sudden swerve or an accident.

1

Before driving

111

1-7. Safety information

Installing child restraints

Follow the child restraint system manufacturer’s instructions. Firmly
secure child restraints to the seats using the LATCH anchors or a
seat belt. Attach the top tether strap when installing a child restraint.

The lap/shoulder belt can be used if your child restraint system is
not compatible with the LATCH (Lower Anchors and Tethers for Chil­dren) system.

■ Using the LATCH anchors

Access Cab models

Child restraint LATCH anchors

LATCH anchors are pro­vided for the each rear seat.

Double Cab models

112

Child restraint LATCH anchors

LATCH anchors are pro­vided for the outside rear
seats.

Buttons displaying the loca­tion of the anchors are
attached to the seats.

■ Using the seat belts

Seat belts equipped with a
child restraint locking mecha­nism (ALR/ELR belts except
driver’s seat belt) (→P. 63)

■ Using the top tether strap

Regular Cab models with bench type seat

Anchor bracket (for top tether
strap)

1-7. Safety information

1

Before driving

Anchor bracket is provided
for each passenger seat.

113

1-7. Safety information

Regular Cab models with separated type seat

Anchor bracket (for top tether
strap)

Anchor bracket is provided
for passenger seat.

Access Cab models

114

Anchor bracket (for top tether
strap)

Anchor bracket is provided
for each rear seat.

Double Cab models

1-7. Safety information

Anchor bracket (for top tether
strap)

Anchor bracket is provided
for each rear seat.

1

Before driving

115

1-7. Safety information

Installation with LATCH system (Access Cab models)

Type A

Latch the hooks of the
lower straps onto the
LATCH anchors and
tighten the lower straps.

If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top
tether strap anchor.

For owners in Canada:
A symbol on a child restraint sys­tem indicates the presence of a

Canada
only

lower connector system.

116

Type B

Canada
only

1-7. Safety information

Latch the buckles onto
the LATCH anchors.

If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top
tether strap anchor.

For owners in Canada:
A symbol on a child restraint sys­tem indicates the presence of a
lower connector system.

1

Before driving

117

1-7. Safety information

Installation with LATCH system (Double Cab models)

Type A

Widen the gap between
the seat cushion and
seatback slightly.

Latch the hooks of the
lower straps onto the
LATCH anchors and
tighten the lower straps.

If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top
tether strap anchor.

For owners in Canada:

Canada
only

A symbol on a child restraint sys­tem indicates the presence of a
lower connector system.

118

Type B

Canada
only

1-7. Safety information

Widen the gap between
the seat cushion and
seatback slightly.

Latch the buckles onto
the LATCH anchors.

If the child restraint has a
top tether strap, the top
tether strap should be
latched onto the top
tether strap anchor.

For owners in Canada:
A symbol on a child restraint sys­tem indicates the presence of a
lower connector system.

1

Before driving

Installing child restrain t s usin g a seat belt (chi ld restra int lock fun ction be lt)

■ Rear-facing (Regular Cab models) — Infant seat/convertible

seat

Never install a rear-facing child restraint. Your vehicle is not
designed to carry an infant.

■ Rear-facing (Access Cab and Double Cab models) ⎯ Infant

seat/convertible seat

Place the child seat on the rear
seat facing the rear of the vehi­cle.

119

1-7. Safety information

Run the seat belt through the
child seat and insert the plate
into the buckle. Make sure that
the belt is not twisted.

Fully extend the shoulder belt
and then allow it to retract
slightly in order to activate the
ALR lock mode.

Lock mode allows the seat belt to
retract only.

■ Forward-facing ⎯ Convertible seat

120

While pushing the child seat
down into the rear seat, a llow th e
shoulder belt to retract until the
child seat is securely in place.

After the shoulder belt has
retracted to a point where there is
no slack in the belt, pull the belt to
check that it cannot be extended.

Place the child seat on the seat
facing the front of the vehicle.

1-7. Safety information

Run the seat belt through the
child seat and insert the plate
into the buckle. Make sure that
the belt is not twisted.

Fully extend the shoulder belt
and then allow it to retract
slightly in order to activate the
ALR lock mode.

Lock mode allows the seat belt to
retract only.

1

Before driving

While pushing the child seat into
the seat, allow the shoulder belt
to retract until the child seat is
securely in place.

After the shoulder belt has
retracted to a point where there is
no slack in the belt, pull the belt to
check that it cannot be extended.

If the child restraint has a top tether strap, the top tether strap
should be latched onto the top tether strap anchor.
(→P. 123, 126, 127)

121

1-7. Safety information

■ Booster seat

Place the booster seat on the
seat facing the front of the vehi­cle.

Sit the child in the booster seat.
Fit the seat belt to the booster
seat according to the manufac­turer’s instructions and insert the
plate into the buckle. Make sure
that the belt is not twisted.

Check that the shoulder belt is
correctly positioned over the
child’s shoulder, and that the lap
belt is as low as possible.
(→P. 63)

Removing a child restraint installed with a seat belt

Push the buckle release button
and fully retract the seat belt.

122

1-7. Safety information

Child restraint systems with a top tether strap (Regular Cab models)

■ Bench type seat

Right side passenger seat

Remove the head restraint.
Installing position:

Right side passenger seat
Center passenger seat

Swing the seatback forward
slightly (→P. 50) and remove the
anchor bracket covers.

Installing position:

Right side passenger seat
Center passenger seat

Store the removed cover in a safe
place such as the glove box.

Route the top tether strap
through the routing device as
shown in the illustration.

1

Before driving

Make sure the top tether strap is
not twisted.

Latch the hook onto the
anchor bracket.

Return the seatback to its orig­inal position.

Make sure the seatback is
securely locked by pushing for­ward and rearward on the top of
the seatback.

123

1-7. Safety information

Center passenger seat

Secure the child restraint using a seat belt or lower anchors,
and tighten the top tether strap.

Make sure the top tether strap is securely latched.

Route the top tether strap
through the routing device as
shown in the illustration.

Make sure the top tether strap is
not twisted.

Latch the hook onto the
anchor bracket.

Return the seatback to its orig­inal position.

Make sure the seatback is
securely locked by pushing for­ward and rearward on the top of
the seatback.

124

Replace the head restraint.
Installing position:

Right side passenger seat
Center passenger seat