Toyota FJ 2007 User Manual
TOYOTA FJ CRUISER 2007 - REAR SPEAKER UPGRADE
A
Preparation
Part Number: TMS-SA-FJ
Code:
Kit Contents
Item # Quantity Reqd. Description
1 2 Rear Speaker Assembly
2 2 Replacement Grilles
Hardware Bag Contents
Item # Quantity Reqd. Description
1 8 Push nuts for Grilles
Additional Items Required For Installation
Item # Quantity Reqd. Description
Conflicts
Conflicts with factory installed rear speakers
Recommended Tools
Personal & Vehicle
Notes
Protection
Vehicle Protection Seat/Floor Covers Part Protection Blankets
Special Tools Notes
Dremel Tool
Dremel Cable Tool
FJ Cable Tool Guide
Installation Tools Notes
Panel Removal Tool Nylon Removal Tool (NRT)
Pliers 1. Diagonal Cutters
2. Long Nose (optional)
Screwdriver Magnetized Philips # 2
Screwdriver Magnetized Philips # 1
Panel Cutout Template Spiral Bit
Torque Wrench 36”lbs 3/32” Drill Bit
Special Chemicals Notes
Cleaner
General Applicability
Conflicts with factory installed rear speakers
Recommended Sequence of Application
Item # Accessory
1 Install Security/Audio
2 Install Bazooka Tube
3 Install Door Sills
4 Install Molded Dash
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item # Quantity Reqd. Description
1
Legend
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY:
injury.
CAUTION:
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT:
specific tools and equipment recommended for this
process.
REVISION MARK:
installation with respect to previous issue.
A process that must be carefully observed
Use caution to avoid risk of
Used in Figures calls out the
This mark highlights a change in
Speaker Specifications / Replacement Parts
Size
Frequency Response
Magnet Size
Efficiency
Power Handling
Weight
Impedance
3.5 inch (nominal) 125 Hz – 20kHz 8 oz. 90 dB 45 watts each 2 lbs. 4 ohms
SPECIAL NOTE: Installation Sequences
fter TMS and Safety mandated preparatory steps have been
taken, the installation sequence is the suggested method for
completing the accessory installation. In some instances the
suggested sequence is written for one associate to install and in
others the sequence is given as part of a team accessory
installation. Unless otherwise stated in the document, the
associates may perform the installation steps in any order to
make the installation as efficient as possible while maintaining
consistent quality.
Southeast Toyota Distributors LLC
Page 1 of 5 pages
TOYOTA FJ CRUISER 2007 - REAR SPEAKER UPGRADE
Procedure
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:-
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
.
1. Install Speaker.
(a) Using NRT, remove blank panel. Fig 1A.
(b) Plug wiring harness into plug behind panel.
Fig 1B.
(c) Hold speaker in place, and hand tighten
silver screws as indicated to swing locks
out behind speaker assembly until tight
against sheet metal. Over tightening could
break assembly. Fig 1C.
2. Cut Speaker Cover
(a) Using supplied template and Dremel tool,
cut the panel as shown in figure 2A.
(b) Using supplied template drill (4) 3/32 holes
in panel as shown in figure 2B.
3. Install Grille into Speaker Cover
NOTE: Use side cutters to trim ribs on back of
cover. Fig 3A
(a) Using supplied push nuts, carefully secure
four mounting posts on Grille as shown in
figure 3A
(b) Reinstall Speaker Cover / Grille Assembly.
Southeast Toyota Distributors LLC
Page 2 of 5 pages
.
Fig. 1A Fig. 1B
Fig. 1C
Fig. 2A
Fig. 2B Fig. 3A
Loading...