Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering and
quality construction of each vehicle we build.
This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupants
follow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. For
important information about this manual and your Toyota, read the foll owing pages carefully.
When it comes to service, remember that your Toyota dealer knows your vehicle very well and is interested in your complete
satisfaction. Your Toyota dealer will provide quality maintenance and any other assistance you may require.
If there is not a Toyota dealer near you, please call the following number:
U.S. OWNERS:
CANADIAN OWNERS:
Please leave this Owner ’s Manual in this vehicle at the time of resale. The next owner will need this information also.
All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy of
continual product improvement, we reserve the right to make changes at any time without notice.
Please note that this manual applies to all models and explains all equipment, including options. Therefore, you may
find some explanations for equipment not installed on your vehicle.
Please access our websites for further information.
D The U.S. mainlandwww.toyota.com
D Hawaiiwww.toyotahawaii.com
D Canadawww.toyota.ca
D When traveling in the U.S. mainland or Canada:
Toyota Customer Experience CenterToll−fr ee:1−800−331−4331
All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of Toyota
Motor Corporation.
i
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
Important information about this manual
Safety and vehicle damage warnings
Throughout this manual, you will see safety and vehicle damage warnings. You must follow these warnings carefully to
avoid possible injury or damage.
The types of warnings, what they look like, and how they are
used in this manual are explained as follows:
CAUTION
This is a warning against anything which may cause
injury to people if the warning is ignored. You are
informed about what you must or must not do in
order to reduce the risk of injury to yourself and
others.
NOTICE
This is a warning against anything which may cause
damage to the vehicle or its equipment if the warning
is ignored. You are informed about what you must or
must not do in order to avoid or reduce the risk of
damage to your vehicle and its equipment.
Safety symbol
When you see the safety symbol
shown above, it means: “Do not...”;
“Do not do this”; or “Do not let this
happen”.
ii
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
Important information about your Toyota
Occupant restraint systems
Toyota encourages you and your family to take the time to
read Section 1−3 of this Owner’s Manual carefully. In
terms of helping you understand how you can receive the
maximum benefit of the occupant restraint systems this
vehicle provides, Section 1−3 of this Owner’s Manual is
the most important section for you and your family to read.
Section 1−3 describes the function and operation concerning seats, seat belts, SRS airbags and child restraint systems of this vehicle and some potential hazards you
should be aware of. These systems work together along
with the overall structure of this vehicle in order to provide
occupant restraint in the event of a crash. The effect of
each system is enhanced when it is used properly and
together with other systems. No single occupant restraint
system can, by itself, provide you or your family with the
equal level of restraint which these systems can provide
when used together. That is why it is important for you and
your family to understand the purpose and proper use of
each of these systems and how they relate to each other.
The purpose of all occupant restraint systems is to help
reduce the possibility of death or serious injury in the
event of a collision. None of these systems, either individually or together, can ensure that there is no injury in the
event of collision. However, the more you know about
these systems and how to use them properly, the greater
your chances become of surviving an accident without
death or serious injury.
Seat belts provide the primary restraint to all occupants of
the vehicle, and every occupant of the vehicle should wear
seat belts properly at all times. Children should always be
secured in child restraint systems that are appropriate for
their age and size. SRS (Supplemental Restraint System)
airbags are, as their names imply, designed to work with,
and be supplemental to, seat belts and are not substitutes
for them. SRS airbags can be very effective in reducing
the risk of head and chest injuries by preventing contact of
the head and chest with interior portions of the vehicle.
iii
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
In order to be effective, the SRS airbags must deploy with
tremendous speed. The rapid deployment of the SRS airbags makes the SRS airbags themselves potential sources
of death or serious injury if an occupant is too close to an
airbag, or if an object or some part of his or her body has
been placed between the occupant and the airbag at the
time of deployment. This is just one example of how the
instructions in Section 1−3 of this Owner ’s Manual will help
ensure proper use of the occupant restraint systems, and
increase the safety they can provide to you and your family in the event of an accident.
Toyota recommends you to read the provisions in Section
1−3 carefully and refer to them as needed during your time
of ownership of this vehicle.
Event data recorder
Your vehicle has computers that monitor and control certain aspects of your vehicle. These computers assist in
driving and maintaining optimal vehicle performance. Besides storing data useful for troubleshooting, there is a
system to record data in a crash or a near car crash
event. This is called an Event Data Recorder (EDR).
The SRS airbag sensor assembly contains the EDR. In a
crash or a near car crash event, this device may record
some or all of the following information:
D Engine speed
D Whether the brake pedal was applied or not
D Vehicle speed
D To what extent the accelerator pedal was depressed
D Position of the transmission selector lever
D Whether the driver and front passenger wore the seat
belts or not
D Driver’s seat position
D Front passenger’s occupant classification
iv
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
D SRS airbag deployment data
D SRS airbag system diagnostic data
If your vehicle is equipped with a vehicle stability control
(VSC) system, its Electronic Control Unit (ECU) may contain another EDR. There are a variety of driving situations
which include activating the VSC under which the VSC
EDR will record certain information. The VSC EDR may
record some or all of the following information:
D Behavior of the vehicle
D Steering wheel angle
D Vehicle speed
D To what extent the accelerator pedal was depressed
D To what extent the brake pedal was applied
D To what extent the ECU controlled the condition of
the 4 wheels
D Vehicle stability control system diagnostic data
The information above is intended to be used for the
purpose of improving vehicle safety performance. Unlike
general data recorders, the EDR does not record sound
data such as conversation between passengers.
Toyota will not disclose the data recorded in an EDR to a
third party except when:
D An agreement from the vehicle’s owner (or the leas-
ing company for a leased vehicle) is obtained
D Officially requested by the police or other authorities
D Used as a defense for Toyota in a law suit
D Ordered by the court
However, if necessary Toyota will:
D Use the data for research on Toyota vehicle safety
performance
D Disclose the data to a third party for research pur-
poses without disclosing details of the vehicle owner,
and only when it is deemed necessary
D Disclose summarized data cleared of vehicle identifi-
cation information to a non−Toyota organization for
research purposes
v
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
New vehicle warranty
Your new vehicle is covered by the following Toyota limited
warranties:
D New vehicle warranty
D Emission control systems warranty
D Others
For further information, please refer to the “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement”.
Your responsibility for
maintenance
It is the owner’s responsibility to make sure that the specified maintenance is performed. Section 6 gives details of
these maintenance requirements. Also included in Section
6 is general maintenance. For scheduled maintenance information, please refer to the “Scheduled Maintenance
Guide” or “Owner’s Manual Supplement”.
Important health and safety
information about your Toyota
CAUTION
D WARNING: Engine exhaust, some of its constitu-
ents, and a wide variety of automobile components contain or emit chemicals known to the
State of California to cause cancer and birth defects and other reproductive harm. In addition,
oils, fuels and fluids contained in vehicles as
well as waste produced by component wear contain or emit chemicals known to the State of
California to cause cancer and birth defects or
other reproductive harm.
D Battery posts, terminals and related accessories
contain lead and lead compounds. Wash your
hands after handling. Used engine oil contains
chemicals that have caused cancer in laboratory
animals. Always protect your skin by washing
thoroughly with soap and water.
vi
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
Accessories, spare parts and
modification of your Toyota
A wide variety of non−genuine spare parts and accessories
for Toyota vehicles are currently available in the market.
You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or
replacement, or for any damage they may cause to, or
adverse effect they may have on, your Toyota vehicle.
This vehicle should not be modified with non−genuine
Toyota products. Modification with non−genuine Toyota
products could affect its performance, safety or durability,
and may even violate governmental regulations. In addition, damage or performance problems resulting from the
modification may not be covered under warranty.
Spark ignition system of your
Toyota
The spark ignition system in your Toyota meets all requirements of the Canadian Interference−Causing Equipment
Standard.
Installation of a mobile
two−way radio system
As the installation of a mobile two−way radio system in
your vehicle could affect electronic systems such as
multiport fuel injection system/sequential multiport fuel
injection system, electronic throttle control system, cruise
control system, anti−lock brake system, traction control
system, vehicle stability control system, SRS airbag system and seat belt pretensioner system, be sure to check
with your Toyota dealer for precautionary measures or
special instructions regarding installation.
vii
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
Tires and loading on your
Toyota
Underinflated or overinflated tire pressure and the
excess load may result in the deterioration of
steering ability and braking ability, leading to an
accident. Check the tire inflation pressure periodically and be sure to keep the load limits given in
this Owner’s Manual. For details about tire inflation
pressure and load limits, see pages 201 and 267.
’08 Corolla_U (L/O 0706)
Scrapping of your Toyota
The SRS airbag and seat belt pretensioner devices in your
Toyota contain explosive chemicals. If the vehicle is
scrapped with the airbags and pretensioners left as they
are, this may cause an accident such as fire. Be sure to
have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by the qualified service
shop or by your Toyota dealer before you dispose of your
vehicle.
viii
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
Leak detection pump
This pump performs fuel evaporation leakage check. This
check is done approximately five hours after the engine is
turned off. So you may hear sound coming from underneath the trunk for several minutes. It does not indicate a
malfunction.
Perchlorate Material
Special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
Your vehicle has components that may contain perchlorate.
These components may include airbag, seat belt pretensioners, and wireless remote control batteries.
These keys work in every lock. Your
Toyota dealer will need one of them to
make a new key with a built−in transponder chip.
Since the doors and trunk lid can be
locked without a key, you should always carry a spare master key in case
you accidentally lock your keys inside
the vehicle.
’08 Corolla_U (L/O 0706)
2. Sub key (gray)—
This key will not work in the trunk.
To protect items locked in the trunk
when using valet parking, leave the
sub key with the attendant.
A transponder chip for engine immobilizer
system has been placed in the head of
the master and sub keys. These chips are
needed to enable the system to function
correctly, so be careful not to lose these
keys. If you make your own duplicate key,
you will not be able to cancel the system
or start the engine.
NOTICE
When using a key containing a transponder chip, observe the following
precautions:
z When starting the engine, do not
use the key with a key ring resting
on the key grip and do not press
the key ring against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts.
10
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
z When starting the engine, do not
use the key with other transponder
keys around (including keys of other vehicles) and do not press other
key plates against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts. If
this happens, remove the key once
and then insert it again after removing other transponder keys (including keys of other vehicles) from the
ring or while gripping or covering
them with your hand to start the
engine.
’08 Corolla_U (L/O 0706)
z Do not bend the key grip.
z Do not cover the key grip with any
material that cuts off electromagnetic waves.
z Do not knock the key hard against
other objects.
z Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard and hood
under direct sunlight.
z Do not put the key in water or
wash it in an ultrasonic washer.
z Do not use the key with electromag-
netic materials.
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
11
’08 Corolla_U (L/O 0706)
Engine immobilizer system
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
12
The engine immobilizer system is a
theft prevention system. When you insert the key in the ignition switch, the
transponder chip in the key’s head
transmits an electronic code to the vehicle. The engine will start only when
the electronic code in the chip corresponds to the registered ID code for
the vehicle.
Never leave the keys inside the vehicle
when you leave the vehicle.
Without Toyota vehicle intrusion protection system
With Toyota vehicle intrusion protection
system
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
The system is automatically set when the
key is removed from the ignition switch.
The indicator light will start flashing to
show the system is set.
If any of the following indicator conditions
occurs, contact your Toyota dealer.
D The indicator light stays on except
when the Toyota vehicle intrusion
protection system is setting or activating. (See “Toyota vehicle intrusion
protection system (TVIP)” on page 25
in this Section.)
D The indicator light does not start flash-
ing when the key is removed from the
ignition switch.
D The indicator light flashes inconsistent-
ly.
Inserting the registered key in the ignition
switch automatically cancels the system,
which enables the engine to start. The
indicator light will go off.
The system is maintenance−free.
For your Toyota dealer to make you a
new key with built−in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
If you make your own duplicate key,
you will not be able to cancel the system or start the engine.
NOTICE
Do not modify, remove or disassemble the engine immobilizer system. If any unauthorized changes or
modifications are made, proper operation of the system cannot be guaranteed.
For vehicles sold in U.S.A.
FCC ID: MOZRI−21BTY
FCC ID: MOZRI−20BTY
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
13
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
For vehicles sold in Canada
This device complies with RSS−210 of
Industry Canada. Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
’08 Corolla_U (L/O 0706)
Wireless remote control—
1. “LOCK” switch
2. “UNLOCK” switch
3. “PANIC” switch
The wireless remote control system is
designed to lock or unlock all the
doors or activate the “PANIC” mode
from a distance within approximately 1
m (3 ft.) of the vehicle.
When you operate any switch, push it
slowly and securely.
The wireless remote control transmitter is
an electronic component. Observe the following instructions in order not to cause
damage to the transmitter.
D Do not leave the transmitter in places
where the temperature becomes high
such as on the dashboard.
D Do not disassemble it.
D Avoid knocking it hard against other
objects or dropping it.
D Avoid putting it in water.
You can use up to 4 wireless remote control transmitters for the same vehicle.
Contact your Toyota dealer for detailed
information.
14
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
If the wireless remote control transmitter
does not actuate the doors or alarm, or
operate from a normal distance:
D Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the transmitter.
D The battery may have been consumed.
Check the battery in the transmitter. To
replace the battery, see “—Replacing
transmitter battery” on page 16.
If you lose your transmitter, contact your
Toyota dealer as soon as possible to
avoid the possibility of theft, or an accident. (See “If you lose your wireless remote control transmitter” on page 238 in
Section 4.)
This complies with Part 15 of the FCC
rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
’08 Corolla_U (L/O 0706)
—Locking and unlocking
doors
Locking operation
To lock and unlock all the doors, push
the switches of the transmitter slowly
and securely.
To lock: Push the “LOCK” switch. All the
doors are locked simultaneously. At this
time the turn signal lights will flash once.
Check to see that the doors are securely
locked.
If any door is not securely closed, locking
cannot be performed by the “LOCK”
switch.
To unlock: Push the “UNLOCK” switch
once to unlock the driver’s door alone.
Pushing the switch twice within 3 seconds
unlocks all the doors simultaneously. Each
time the “UNLOCK” switch is pushed, the
turn signal lights will flash twice.
When the doors are unlocked, the interior
light comes on and remains on for about
15 seconds before fading out. (For further
information, see “Interior light” on page 93
in Section 1−5.)
You have 30 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
doors will be automatically locked again.
Unlocking operation
15
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
If the “LOCK” or “UNLOCK” switch is kept
pressed in, the locking or unlocking operation is not repeated. Release the switch
and then push again.
’08 Corolla_U (L/O 0706)
—Activating panic mode
Pushing the “PANIC” switch blows the
horn intermittently and flashes the
headlights, tail lights, turn signal lights
and interior light.
The “PANIC” mode is used to deter vehicle theft when you witness anyone attempting to break into or damage your
vehicle.
The alarm will last for one minute. To stop
the alarm midway, push any switch on the
transmitter or turn the ignition key from
the “LOCK” to “ON” position.
The “PANIC” mode does not work when
the ignition key is in the “ON” position.
—Replacing transmitter
battery
For replacement, use a CR2032 lithium
battery or equivalent.
CAUTION
Special care should be taken to prevent small children from swallowing
the removed transmitter battery or
components.
NOTICE
z When replacing the transmitter bat-
tery, be careful not to lose the components.
z Replace only with the same or
equivalent type recommended by a
Toyota dealer.
z Dispose of used batteries according
to the local laws.
Replace the transmitter battery by following these procedures:
16
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
1. Using a coin or equivalent, open the
transmitter case.
2. Remove the discharged transmitter battery.
3. Put in a new transmitter battery with
positive (+) side up.
Close the transmitter case securely.
After replacing the battery, check that the
transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.
17
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
NOTICE
z Do not bend the terminals.
z Make sure the positive side and
negative side of the transmitter battery are faced correctly.
z Do not replace the battery with wet
hands. Water may cause unexpected
rust.
z Do not touch or move any compo-
nents inside the transmitter, or it
may interfere with proper operation.
z Be careful not to bend the electrode
when inserting the transmitter battery and that dust or oils do not
adhere to the transmitter case.
z Close the transmitter case securely.
’08 Corolla_U (L/O 0706)
Side doors—
When the doors are unlocked, the interior
light comes on and remains on for about
15 seconds before fading out. (For further
information, see “Interior light” on page 93
in Section 1−5.)
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
Vehicles with power door lock system—
All the doors lock and unlock simultaneously with either front door. In the driver’s door lock, turning the key once will
unlock the driver’s door and twice in succession will unlock all the doors simultaneously.
18
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward.
To unlock: Pull the knob backward.
The front doors can be opened by pulling
the inside handle even if the lock knobs
are in the locked position.
’08 Corolla_U (L/O 0706)
CAUTION
Do not pull the inside handle of the
front doors while driving. The doors
will open and an accident may occur.
Toyota strongly recommends that all
children be placed in the rear seat of
the vehicle.
Closing the door with the lock knob in the
lock position will also lock the door. Be
careful not to lock your keys in the vehicle.
Vehicles with power door lock system—
Doors cannot be locked when either front
door is open and the key is in the ignition.
Driver’s side
Passenger’s side
19
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
’08 Corolla_U (L/O 0706)
LOCKING AND UNLOCKING WITH
POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch down on the
front side.
To unlock: Push the switch down on the
rear side.
Operating the switch simultaneously locks
or unlocks all the doors.
If you do either of the following, no door
can be unlocked with the power door lock
switch.
D Lock all the doors with the key or wire-
less remote control transmitter when all
the doors are closed.
D Open the driver’s door or front passen-
ger’s door and move the inside lock
knobs of both front doors to the lock
position, then close the front doors.
The power door lock switch can be reset
in the following ways.
D Turn the ignition key to “ON”.
D Unlock all the doors with the key or
wireless remote control transmitter.
D Unlock the driver’s door or front pas-
senger’s door with the inside lock
knob, and then unlock all the doors
with the power door lock switch.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the vehicle in an accident. It also helps prevent the doors from being opened
unintentionally.
REAR DOOR CHILD−PROTECTORS
Move the lock lever to the “LOCK”
position as shown on the label.
When the child−protector is locked, you
cannot open the rear door by the inside
door handle. We recommend using this
feature whenever small children are in the
vehicle.
20
2008 COROLLA from Aug. ’07 Prod. (OM12B28U)
Loading...
+ 280 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.