Toyota Corolla 2004 Repair Manual - FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1 LH
–FRONT SUSPENSION FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1
LH
FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1 LH
REPLACEMENT
HINT:
COMPONENTS: See page 26–3
1. REMOVE FRONT WHEEL
2. DISCONNECT FRONT STABILIZER LINK ASSY LH (LH (A/T) POSITION)(See page 26–8)
3. DISCONNECT FRONT STABILIZER LINK ASSY RH (LH (A/T) POSITION)
HINT:
Remove the RH side by the same procedures as the LH side.
4. SEPARATE FRONT SUSPENSION ARM SUB–ASSY
LOWER NO.1 LH
(a) Remove the bolt and 2 nuts, and separate the front sus-
pension arm sub–assy lower No.1 LH from the lower ball
joint assy front LH.
26–13
2607X–01
C80293
5. SEPARATE FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1 RH (LH (A/T) POSITION)
HINT:
Remove the RH side by the same procedures as the LH side.
6. SEPARATE RACK & PINION POWER STEERING GEAR ASSY (LH (A/T) POSITION)
(a) Remove the 4 bolts, separate the rack & pinion power steering gear assy.
NOTICE:
Loosen the bolt since the nut cannot be rotated.
(b) Suspend the rack & pinion power steering gear assy.
7. SUSPEND ENGINE ASSY (LH (A/T) POSITION)(See page 40–9)
8. SEPARATE FRONT SUSPENSION CROSSMEMBER
SUB–ASSY (LH (A/T) POSITION)
(a) Remove the 3 bolts and 3 nuts, disconnect the transverse
engine engine mounting insulator and engine mounting
member sub–assy center from the front suspension
crossmember sub–assy.
C86742
2004 COROLLA (RM1037U)
1244Author: Date:
26–14
C87404
–FRONT SUSPENSION FRONT SUSPENSION ARM SUB–ASSY LOWER NO.1
LH
(b) Remove the 4 bolts.
(c) Lower the transmission jack, remove the front suspension
crossmember sub–assy.
9. REMOVE FRONT SUSPENSION ARM SUB–ASSY
LOWER NO.1 LH
(a) Remove the 2 bolts, nut and front suspension arm sub–
assy lower No.1 LH from the front suspension crossmember sub–assy.
C64941
C87403
10. TEMPORARY TIGHTEN FRONT SUSPENSION ARM
SUB–ASSY LOWER NO.1 LH
(a) Install the front suspension arm sub–assy lower No. 1 LH,
temporarily tighten the 2 bolts and nut.
11. INSTALL FRONT SUSPENSION CROSSMEMBER
SUB–ASSY (LH (A/T) POSITION)
(a) Lift the front suspension crossmember sub–assy up with
a transmission jack.
C87403
(b) Insert SST to the base hole of the RH side crossmember
and RH side of the vehicle.
SST 09670–00010
(c) Tighten the bolt temporarily in the order A and B.
B
SST
A
C65019
B
C64940
2004 COROLLA (RM1037U)
A
SST
(d) Insert SST to the base hole of the LH side of crossmem-
ber and LH side of the vehicle.
SST 09670–00010
(e) Tighten the bolt temporarily in the order A and B.
(f) Insert SST to the base hole of the RH side of crossmem-
ber and RH side of the vehicle.
SST 09670–00010
C65020
1245Author: Date:
Loading...