Page 1
Please refer to the following sourc es for additiona l information:
• Your vehicle’s Owner’s Manua l
• Your vehicle’s Repair M anual
M oving parts like the fa n blade a nd drive belts, as w ell as extreme
heat in the engine compartment or from the exhaust system can
result in serious injury.
• Approach with caution and ca re.
• Never take shortcuts whe n replac ing parts.
• Improper servicing may dama ge your Toyota and lead to
personal injury.
• Unless you have prope r knowle dge, equipment a nd tools, you
should have your Toyota Dealer Se rvice Departme nt perform
the repairs and mainte nance .
Proper installa tion of Genuine Toyota replac ement pa rts is essential
for the safe and relia ble opera tion of your vehicle.
Following these instructions will:
• Help to assure your personal safe ty
• Assist you in the proper repla cement of specific parts
There a re many variations in the step- by-step proc edures used in
installing various parts, and va rying skill levels of individuals doing
the parts re place ment. These instructions cannot anticipate all
circumsta nces or provide advice a nd caution on each. I f you are
in doubt concerning your ability to replac e the pa rt or have a ny
questions, consult your local Toyota Dea ler Service De partment
and have the work performed by an experienc ed technician.
For further assistance, contact your Toyota dealer.
REFERENCES
CAUTION
IMPORTANT SAFETY NOTICE
Visit our W eb site at w ww.toyota.com
M /N 00405-HOW TO-DM LMP
CONDITI ON ACTION
Bulb does not work, flickers or
is dim:
Check that the bulb is correctly
seate d in the socket.
Check that the socket is cle an.
Check that the wire s have not
come loose.
Check that the bulb is intact
(no damage, no loose bulb
ends, no broken filame nt).
If problems persist, there could
be a fa ult with the vehicle’s
wiring or e lectrical system.
Contact your Toyota Deale r
Service Department for
diagnosis and repa ir.
TROUBLESHOOTING
DomeLampHowToBroch(New).qxd 7/21/04 7:01 PM Page 1
Page 2
REMOVE THE BULB LENS COVER – Using the screw driver,
care fully relea se the lens cover from its housing.
ALWAYS REMOVE THE KEYS FROM THE IGNITION W HEN
WORKING ON THE VEHICLE. SEE
CAUTION ON BACK PANEL.
DOUBLE-ENDED BULBS – These are prima rily used for interior
dome lights.
DIFFICULTY LEVEL
• Genuine Toyota Replace ment Bul b
• Flat-tip (– shaped) scre w driver (small #1)
• Rag or paper tow el s
IN SPECT THE LENS COVER – Check for cra cks, damage and
deterioration. Replace as required.
IN STALL A NEW B ULB – Carefully pull back one of the spring
clips to seat the bulb betw een the clips, then rele ase tension
on the clip and ma ke sure the bulb is properly seate d.
REMOVE THE BURNED-OUT BULB – Care fully pull back one of
the spring clips to rele ase tension on the bulb. If the bulb is stuck,
use the screwdriver to rele ase the bulb from the spring clips.
5-10
M INU TES
CAUTION: M ake sure the drive r’s and passenger’s doors are closed
and that the dome lamp sw itch is in the “off” position before
changing the bulb.
FROM ONE TO FOUR–FOUR BEING THE MOST DIFFICULT
INSTRUCTIONS
TOOLS AND SUPPLIES
1
2
INSTRUCTIONS
(continued)
INSTRUCTIONS
(continued)
3
5
CHECK FOR LOOSE WIRES OR CONN ECTORS – Repair or
replac e as re quired.
6
IN SPECT THE SOCKET FOR DIRT AND CORROSION – Clea n off
any dirt with a rag or paper tow el. If corroded, the light socket(s),
wire connec tor, and/or light assembly may re quire re place ment.
Consult your Toyota Deale r Service and/ or Parts De partments
for details and parts.
4
7
IN STALL THE BULB COVER.
8
CHECK THAT THE LIGHT WORKS.
9
ESTIM ATED TIM E INV OLVED
DomeLampHowToBroch(New).qxd 7/21/04 7:01 PM Page 2
Loading...