TOYO ELECTRIC MFG TY S 2400 Users manual

User Instructions for Model TY-R-2400, TY-T4 and TY-S-2400

Battery Installation

1. Remove the remote control and battery from the poly bag.

2. Open the battery cover on the back of the remo te by sliding the cover towards the bottom of the
remote

3. Clean the battery contacts and also those of the d evice prior to battery installation.

4. Use only 12V Alkaline battery type 23A for replacement, use of other batteries may damage remote.

5. Insert negative (-) end of the battery (see marking on battery) into the spring side of the batte ry
holder and insert positive (+) end of the battery into other side.

6. Close battery cover by sliding back into place.

+

-

Remote Control Operation:

The remote has three buttons on the front side to operate the controller with 2422MHz receiver and
conneced light set:

a. ON/OFF – this is the upper button. Press to turn th e set OFF. Press again to turn the set ON.

Note: even when the lights are off, the set still has power to all lamps, to disconnect power,
you must unplug the set.

b. FUNCTION – this is the second button. Press to change the light pattern to the next function

mode. After reaching last function, the s et can be returned to Function 1 by pressing the
function button again. For best results, pause for a few seconds before pushing the

“FUNCTION” button again for the next function.
c. DIMMER – this is the third button. Press to change the brighteness of a certain lighting pattern.
d. SENSOR – this is a lowest button. Press to change the controller working under “ Sensor

“ Mode.

Controller Installation:

FOR WALL MOUNTING
Fasten the screws(pre-attached in the upper section of enclosure) and hook the unit to a wall ; Make
sure the unit fits securely against the wall.
FOR GROUND STAKIING

Slide the ground stake into the slot on the ba se of the unit.Carefully press the stake into the ground.

Plug your Christmas light strings or decorative lighting outfits into the outlets of main controllers TY-T4 and

satellite

controller TY-S-2400 (MAX 420 Wa tts total).
Plug the main power cord into a power outlet (recommended to plug into a receptacle or extended
receptacle protected by GFCI).

Features:

Remote Control Functions

a) Regular mode

16 Pre-programmed Settings ( Note: The sequence of Settings may be veried) , the default setting when

powered is steady on;

1. Combination Light Show (Cycles through functions)

2. Fast Chasin g r i g h t to le ft from one lig ht set to the oth e r

3. Fast Chasing left to right from one light set to another

4. Slow to fast chasing right to left from one light set to another.

5. Slow to fast chasing left to right from one light set to another.

6. Flashing/Chasing combination

7. Alternating flashing

8. Bi-Directional Pulsing

9. Bi-directional Chasing

10. Strobing

11. Random Flashing

12. Bi-directional chasing with flashing

13. Pulsing to Strobing feature.

14. Bi-Directional Strobing

15. Fade in / Fade out

16. Steady on

(b) Sensor mode
As music plays through the speaker with blue tooth feather or memory card, the lights will dance and

flash to the rhythm of the music.
Press the button “ Sensor “ on the panel of remote controller.
Insert the Memory card to the slot, Power on the speaker and the light indicator on the panel is red, the
controller can work under SD card Mode;
pressing the button “ Mode” and the light indicator is blue, the controller cand work under “ blue tooth”
Mode, the speaker can play music sent from your mobile phone or ipod.
Press the “volume” control bar to adjust the volume level as you desire.
Change the songs just press the backward or forward button.

NOTES:

1. Light set must be plugged into working outlet for remote control to function.

2. The remote control unit is the only way to change the function setting of this product.

3. When using the remote to turn your set ON, there may be a slight delay before the light pattern starts
working.

4. To change the light pattern, it is recommended to wait a few seconds after each time you press the
“FUNCTION” button until you reach the desired pattern/function.

5. If the lights do not change function or the set does not turn on or off with the remote, see the trouble
shooting section.

6. If there is a power interruption, including if used on a switched outlet, on a timer, or power failure, the
system’s memory will retain the last light pattern d isplayed.

7. The operating distance of the remote is up to 100 feet ( 30meters). Distance may vary due to other
radio transmitters in the area (cell p hones, Wi-Fi signals, wireless phones, intercoms, baby monitor,
etc.), microwave ovens, computers, materials used in the construction of your home, trees, hills,
bushes and other items that may attenuate the radio signal.

8. The battery in the remote will drain and become depleted very quic kly if the remote is place where
one (or both) of the buttons on the remote are continually pushed (such as placing an item on top
of them, or storing the remote upside down).

NOTES:

A. When multiple light sets are lighted, pressing the FUNCTION button will change all sets to the next

pattern. If the set are preprogrammed, then they should all change to the sam e next pattern.

B. These are Radio Frequency controlled devices. All sets within the effective range will be af fected

and controlled using any one remote.

C. If used with a mechanical / digita l timer, only one timer must control all sets. In this case, do not turn

sets off using the remote or the sets will not turn on with the timer.