TownSteel TSF-300A, TSF-300, TSF-120 Installation Instructions Manual

B A

TSF-300A/300/120
CENTER HUNG PACKAGES

INSTALLATION INSTRUCTIONS

INSERT THE SPINDLE INTO
THE FLOOR HINGE.

1

4

5

2

3

PUT THE WASHER FIRST AND FIT END
SQUARED & ANGLED PART OF SPINDLE INTO
HOLLOW AREA AND TIGHTEN IT BY USE OF
SPINDLE SCREW READY ALREADY.

TURN THE ADJUSTMENT SCREW IN A
ANTICLOCKWISE AND RELEASE PIVOT PIN .
INSTALL THE PIVOT INTO UPPER PART OF DOOR
FRAME. AND COVER IT.

INSERT PIVOT CHANNEL INTO TOP OF DOOR,
INSTALL BEARING INSERT INTO PIVOT CHANNEL.
TIGHTEN UP THE ADJUSTMENT SCREW ALMOST
AND CONTROL THE CENTER POINT OF PIVOT.
FIX THE BEARING TO THE VERY PROPER
LOCATION.

INSTALL IN THE CENTER OF THE FLOOR HINGE
CEMENT BOX AND TIGHTEN THE FASTENING
SCREWS.

MAKE CEMENT BOX AND PUT THE FLOOR HINGE
IN THE CEMENT BOX.

THE UPPER PART OF THE CEMENT BOX SHOULD
BE ON THE LEVEL WITH THE FLOOR SURFACE.
THE CEMENT BOX SHOULD BE A LEVEL SURFACE.
ADDITIONALLY THE CENTER OF SPINDLE HAS TO BE
POSITED CORRECTLY.
FULFILL GROUT AROUND CEMENT BOX.

(LH Door) (RH Door)

CAUTION

-

PUT THE WASHER FIRST.

SPINDLE
SCREW

SPINDLE

WASHER

ADJUSTMENT SCREW

PIVOT

COVER PLATE

FOR SINGLE ACTION
OFFSET 3 °.

FOR DOUBLE ACTION

STANDARD TYPE SPINDLE

FLOOR FINISHED

BEARING INSERT

ADJUSTMENT
SCREW

POIVOT CHANNEL

TOP PIVOT

CAUTION:

1.Dimension indicated is not a real size.

2.Dimensions are in mm.

3.All reinforcement accessories for bottom arm should be prepared by user.

34

25

18

32

Min 34

7

5

25

5

100

169

126

13

70

1479

70

45 25

DOOR GAP 3

12.5

12.5

135

25

90

12

12

Holes for pivot insert x 4 ea

Use

Ø

5.1 drill for M6 X 1.0 mech. Screw.

Holes x 5 ea

Use Ø 4.3 drill for M5 x 0.8 mech. Screw.

REAR view

Door frame position

Front view

SIDE view

PLANE VIEW

R65

DOOR area.

COVER PLATE

C/L

BOTTOM ARM

CAUTION:

1,Dimension indicated is not a real size.

2,Dimensions are in mm.

3,All reinforcement accessories for bottom arm should be prepared by user.

Holes x 5 ea

Use Ø4.3 drill for M5 x 0.8 mech. Screw.

2024

70

36

DOOR GAP 3

Floor area nished

5940

52 52

52

201

Front view

Rear View

R65

C/L

FASTENING SCREWS

B A

TSF-300A/300/120
OFFSET HUNG PACKAGES

INSTALLATION INSTRUCTIONS

INSERT THE SPINDLE INTO
THE FLOOR HINGE.

1

4

5

2

3

PUT THE WASHER FIRST AND FIT END
SQUARED & ANGLED PART OF SPINDLE INTO
HOLLOW AREA AND TIGHTEN IT BY USE OF
SPINDLE SCREW READY ALREADY.

INSTALL TOP PIVOT

REMOVE CAP, PIVOT PIN
AND THEN INSTALL TOP PIVOT.

INSTALL BOTTOM ARM.

INSTALL IN THE CENTER OF THE FLOOR HINGE
CEMENT BOX AND TIGHTEN THE FASTENING
SCREWS.

MAKE CEMENT BOX AND PUT THE FLOOR HINGE
IN THE CEMENT BOX.

THE UPPER PART OF THE CEMENT BOX SHOULD
BE ON THE LEVEL WITH THE FLOOR SURFACE.
THE CEMENT BOX SHOULD BE A LEVEL SURFACE.
ADDITIONALLY THE CENTER OF SPINDLE HAS TO BE
POSITED CORRECTLY.
FULFILL GROUT AROUND CEMENT BOX.

(LH Door) (RH Door)

CAUTION

-

PUT THE WASHER FIRST.

SPINDLE
SCREW

SPINDLE

WASHER

FOR SINGLE ACTION
OFFSET 3 °.

FOR DOUBLE ACTION

STANDARD TYPE SPINDLE

FLOOR FINISHED

CAUTION:

1,Dimension indicated is not a real size.

2,Dimensions are in mm.

3,All reinforcement accessories for bottom arm should be prepared by user.

FASTENING SCREWS

BOTTOM OF DOOR

OFFSET ART

FRAME POSITION

DOOR POSITION

PIVOT PIN

CAP

TOP PIVOT

OFFSET ARM

FRONT VIEW

FRONT VIEW

BACK VIEW

BACK VIEW

CAUTION:

1.Dimension indicated is not a real size.

2.Dimensions are in mm.

3.All reinforcement accessories for bottom arm should be prepared by user.