Town & Country Fireplaces TC36.NG06C, TC36 CHALET II Installation Instructions Manual
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the replace and should be
kept together. Refer to the Installation and Operating Instructions
for proper gas supply, safety requirements and operating
instructions
TC36
CHALET II
BURNER KIT
INSTALLATION
INSTRUCTIONS
050411-16 TC36.NG06C 5056.427C1A
PART# TC36.NG06C
For use with:
Model TC36
Series C
• BURNER ASSEMBLY
• LOG GRATE
• TC36 LOGS
• EMBER MATERIAL
• HARDWARE PACKAGE
Contents of Package
If this replace is to be
used on Propane please
convert prior to installtion.
See pages 9 – 11.
Burner Installation
1. Place the keyhole slots in the burner
over the two screws located in the rebox
base. (Fig. #1 & 1a)
2. Slide the burner back to engage the
screws in the small part of the keyhole
slot and tighten screws. (Fig. #1b)
3. Remove access cover from side of
rebox(Fig. #1c)
Fig. # 1
SCREWS
Fig. # 1c
Fig. # 1a
Fig. # 1b
TC36.NG06C 050411-16
2
Burner/ Grate Installation
4. Secure the electrical bulkhead plate and
gasket to the rebox. (2 screws) Attach the
ignition and sensor wires to the module.
Red end to the connector marked by the
red dot, white end to the connector marked
by the white dot
Fig.#2 & Fig.#3
Fig. # 2
2 SCREWS
BULKHEAD PLATE
Fig. # 3
WHITE END TO
WHITE DOT
MODULE
RED END TO
RED DOT
TC36.NG06C 050411-16
3
5. Attach the pilot and gas supply tubes to
the bulk head tting and tighten.
(Fig. # 4) Ensure the connections are
gas tight. Conceal the spark and
sensor wires below the supply tubes.
A panel set must now be installed. See
Installation and Operating Instructions
manual for details.
Fig. # 4
PILOT SUPPLY
TUBE
MAIN GAS SUPPLY
TUBE
6. Position the slots of the grate securing
brackets over the holes in the oor shield
and secure with the two screws
(Fig. # 5).
Fig. # 5
TC36.NG06C 050411-16
4
Ember Material
A large bag of ember material is shipped
with the replace and needs to be
installed on the burner to ensure optimum
performance and ame appearance.
1. Pull apart the material into ember size
pieces (approximately 1” squares) and
gently place them into the burner pan.
Do not compress, leave them loose for
best performance.
2. Fill the burner pan level with the top of
the pan at rear, and gradually sloping
forward down to the rebox oor at the
front, covering both burner tubes.
3. Place remaining ember material outside
of the burner pan as desired to cover-up
gas lines and brackets.
Note: Ember material placement and
amount will affect ame appearance. More ember material results
in lower flame height. Add or
remove as needed until desired
ame affect.
Fig. # 6
Ember Material Placement
LOG
GRATE
GLOWING EMBERS
Log Set Assembly
Gas plumbing and vent connections should
be completed before proceeding.
The logs are are fragile and should be
handled with care. Unpack and inspect
log set. There should be a total of 7 logs.
Position the logs as indicated by the following
pictures. Place the rear log back against the
tabs located at the back of the grate. Place
left log as pictured, engaging the pins with
corresponding holes on the underside of
the log. Install the right log into the grate
and pull it forward into position as shown.
Place the four remaining small logs on the
oor of the rebox in the positions and order
as shown.
Fig. # 7
LOG #1
TC36.NG06C 050411-16
5
Loading...