Tower Hobbies Nitro ST-15 Assembly And Operation Manual

Warranty

• Tower Hobbies®will warranty this kit for 90 days after the purchase date from defects in materials or

workmanship. Tower

Hobbies will either repair or replace, at no charge, the incorrectly made part.

• Make sure you save the receipt or invoice you were given when you bought your model! It is your proof of purchase and
we must see it before we can honor the warranty.

• To return your Tower Nitro ST-15 for repairs covered under warranty you should send your truck to:

Hobby Services

1610 Interstate Drive

Champaign, Illinois 61822

Attn: Service Department

Phone: [phone]:00 am - 5:00 pm Central Time M-F

E-mail: [e-mail]

Thank you for purchasing the Tower Hobbies 1/10th scale stadium truck. This manual includes instructions to complete the
kit, and information to help operate it properly. Please read over this instruction manual carefully before building or operat­ing the Tower Hobbies 1/10th stadium truck.

ASSEMBLY AND OPERATION MANUAL

Ready To Run

TOWZ1119 for TOWC55**Copyright © 2001 V1.0 Printed in USA

If you follow the safety precautions below the Tower Hobbies
1/10th stadium truck will provide countless hours of fun. Always
use caution and good sense when running the Tower Hobbies
1/10th stadium truck. Failure to use this vehicle in a safe, sensi­ble manner can result in injury or damage to property. Only you
can insure that the instructions are carefully read and followed.

• Do not operate the Tower Hobbies stadium truck near peo­ple. Onlookers should be behind the driver at a safe distance.

• Model engine fuel is poisonous. Please read and follow the
precautions on the fuel container. Keep fuel out of reach of
children. Model fuel is flammable, so keep awa y from flames,
sparks, smoking or any other ignition source.

• Model engines produce loud noises. If loud noises disturb
you then ear protection should be worn. Do not operate the
truck where the noise will disturb others.

• Model engines emit carbon dioxide like real cars. Do not
operate the engine indoors or in poorly ventilated areas.

• When operating your truck around other r/c vehicles make
sure that no one else is on the same frequency as you before
you turn your transmitter on.

• The engine and exhaust, under normal operating conditions,
get very hot. Do not touch these parts until they have cooled.

Repair service is available anytime.
After the 90 day warranty, you can send your Tower Hobbies

1/10th stadium truck in for repair for a small charge by expert
technicians at our authorized repair facility, Hobby Services, at the
address listed on the cover of this instruction manual.

To help speed up the repair process, please follow the instruc­tions listed below.

• You will need to send the entire system in. This includes the
truck and radio.

• Make sure the transmitter is turned off, all batteries are
removed and the fuel is drained from the tank.

• Include written instructions which include a list of all items
returned, a thorough explanation of the problem and the
service needed. You will also need to include your phone
number during the day and a return address.

All pictures, descriptions and specifications found in this instruc­tion manual are subject to change without notice. Tower Hobbies
maintains no responsibility for inadvertent errors in this instruc­tion manual.

The following items will be needed to oper ate the T o wer Hobbies
1/10th stadium truck.

❍ Glow plug starter (TOWP1190)
❍ Fuel bottle (DTXP0150)
❍ Fuel (TOWP1310)
❍ Air filter oil (DTXC2465)
❍ Glow plug wrench (DTXR1170)
❍ Extra glow plugs (OSMG2693)
❍ 12 AA batteries
❍ Polycarbonate paint for the body
❍ Masking tape
❍ Lexan scissors (DTXR1150)
❍ Body reamer (DTXR1155)
❍ Hobby knife (TOWR1010, TOWR1015)

❍ 1. Remove the Tower Hobbies Nitro ST-15, transmitter, and

parts from the box

❍ 2. Uncoil the bundled receiver antenna wire. Run the receiver
antenna wire through your fingers to straighten the receiver wire.
Thread the antenna wire through the bottom side of the antenna
holder which is mounted on the outer throttle servo mount.
Loosen, but do not remove the screws in the throttle servo mount.

FINAL ASSEMBLY

ITEMS REQUIRED FOR COMPLETION

SPECIFICATION & DESCRIPTION

CHANGES

REPAIR SERVICE

SAFETY PRECAUTIONS