Tovis 2015XLS User Manual
User’s Manual
for the
2015XLS
Virtual Window™
Virtual Window™ is a trademark of Dimension Technologies Inc. Rochester, N.Y. The contents
of this manual are for informational purposes only and are subject to change without notice.
Table of Contents
1. INTRODUCTION.......................................................................................................................................1
2. INSTALLATION........................................................................................................................................2
2.1. ITEMS INCLUDED WITH YOUR DTI VIRTUAL WINDOW™............................................................................ 2
2.2. CONNECTION OVERVIEW ...........................................................................................................................2
2.3. COMPUTER CONNECTIONS......................................................................................................................... 3
2.4. VIDEO CONNECTIONS................................................................................................................................ 3
3. GENERAL OPERATION..........................................................................................................................5
3.1. INTRODUCTION ......................................................................................................................................... 5
3.2. 3D CONTROLS .......................................................................................................................................... 6
3.3. IMAGE ADJUSTMENT CONTROLS ................................................................................................................6
3.3.1. Button Reference............................................................................................................................. 7
3.3.2. Main Menu......................................................................................................................................7
3.4. FUNCTION.................................................................................................................................................8
3.5. OPERATING PROCEDURE............................................................................................................................ 9
3.6. SCREEN IMAGE ADJUSTMENT...................................................................................................................10
4. CARE AND HANDLING.........................................................................................................................11
4.1. HANDLING ..............................................................................................................................................11
4.2. ENVIRONMENT........................................................................................................................................ 11
5. MAINTENANCE......................................................................................................................................12
6. SPECIFICATIONS...................................................................................................................................13
6.1. ENVIRONMENTAL.................................................................................................................................... 13
6.2. INTERFACES............................................................................................................................................ 13
6.2.1. VGA.............................................................................................................................................. 13
6.2.2. Video ............................................................................................................................................ 13
6.2.3. Serial............................................................................................................................................13
6.2.4. Stereo Sync. .................................................................................................................................. 13
6.3. ELECTRICAL............................................................................................................................................ 13
6.4. SCREEN................................................................................................................................................... 13
FCC RF
INTERFERENCE STATEMENT
NOTE :
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio, TV technical for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved
by the grantee or manufacturer could void the users authority to operate such equipment.
1. Introduction
The 2015XLS Virtual Window™ sets a new benchmark in autostereoscopic viewing. The Virtual
Window™ produces clear, bright, full-color stereoscopic images that can be seen without the aid
of restrictive viewing devices. With its wide-view autostereoscopic imagery, the Virtual
Window™ will allow for many hours of convenient and comfortable 3D viewing. Stereoscopic
3D imagery, as well as viewing software, is provided with the display.
The Virtual Window™ contains precisely aligned optical components. It is important to exercise
care when handling or moving the display. Be sure to read the Care and Handling section of this
manual, and follow the recommendations provided.
Note that two features described in this manual are optional. Side-by-side stereo support, when
using a computer signal, is one such feature. The other is support for one-channel and twochannel video.
The remainder of this manual describes the installation, operation, and maintenance of the Virtual
Window™ display. Please read the pertinent sections of this manual before installing and
operating the unit. If you encounter any problems with your Virtual Window™, or have any
questions about operating the unit to deliver the best possible performance, please feel free to
contact DTI Technical Support. Contact information should be provided with your purchase
agreement.
In the event that this unit is defective or damaged, purchaser agrees not to open the unit; rather, it
agrees to return the unit to DTI for repair or replacement at purchaser’s expense. If purchaser
does not agree to these terms of sale, it will return the unit to DTI prior to its use of the unit.
Virtual Window User’s Guide 1
2. Installation
NOTE: Please see the “2015XLS Quick-Start Guide” for an illustrated one-page computer
installation guide.
2.1. Items Included With Your DTI Virtual Window™
Your Virtual Window™ is shipped with the following:
• One “DTI Virtual Window™ Quick Start Guide”
• One User Manual (which you are now reading)
• One standard power brick and power cord
• One display interface cable (VGA male to VGA male)
• One serial (RS-232) cable
• A CD-ROM containing PC software for your Virtual Window™
If any of these items appear to be missing, please contact DTI. Contact information can be found
in the “2015XLS Quick-Start Guide.”
2.2. Connection Overview
NOTE: When attaching cables to your Virtual Window, or detaching existing cables, the display
should always be turned off first.
* Video signal inputs are optional. Some models are not applicable for this feature.
The following picture shows the connections on your 2015XLS’s rear panel, along with labels for
each:
The following provides a overview of each connection:
• The ‘VESA Stereo Sync.’ connector is used for Frame Sequential stereo. The stereo sy77nc.
signal, utilized by workstations and high-end PC graphics accelerators, allows your Virtual
Window to recognize which incoming frames are left-eye frames, and which are right-eye
frames.
• The ‘S-Video’ connectors are used for video input. For single-channel video (for example,
from a VCR), the left-hand connector is used for video input.
For dual-channel video, the left-hand connector is used to connect the left-eye camera, while
the right-hand connector is used to connect the right-eye camera.
• The ‘BNC’ connectors are also used for video input; you can use these as an alternative to the
S-Video connectors, if you have a composite video source.
Virtual Window User’s Guide 2
Loading...