TourPro Lighting LED Pin Spot User Manual

!

TourPro LED Pin Spot

User Manual



©2015 TourPro Lighting Company all rights reserved. Information, specifications, diagrams,

images, and instructions herein are subject to change without notice. TourPro Lighting Company

logo and identifying product names and numbers herein are trademarks of TourPro Lighting

Company. Copyright protection claimed includes all forms and matters of copyrightable materials

and information now allowed by statutory or judicial law or hereinafter granted. Product names

used in this document may be trademarks or registered trademarks of their respective companies

and are hereby acknowledged. TourPro Lighting Company and all affiliated companies hereby

disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to

any persons, and direct or indirect economic loss associated with the use or reliance of any

information contained within this document, and/or as a result of the improper, unsafe, insufficient

and negligent assembly, installation, rigging, and operation of this product.

TourPro Lighting Company AUS| 12 Expansion St. | Molendinar, QLD, 4214#
[phone] | | www.tlcflobal.com.au | [e-mail]

Date

Document Version

Software Version

Channel Modes

09/2016

1.1

4,6,7

Page 2

TourPro LED Pin Spot - Manual v1.1



INTRODUCTION

The TourPro LED Pin Spot has been designed to perform reliably for years when the
guidelines in this booklet are followed. Please read and understand the instructions in this

manual carefully and thoroughly before attempting to operate this unit. These instructions

contain important information regarding safety during use and maintenance.

BOX CONTENTS

$(1) powerCON Cable

$(1) 10° Lens

(1) 45° Lens

$Manual#

Page 3

TourPro LED Pin Spot - Manual v1.1



LIMITED WARRANTY

A. TLC GLOBAL (“Tourpro Lighting Company”) warrants this product for the periods set
forth below from the date of purchase, to be free from defects in material and
workmanship:

$• 24 months for DMX-controllable lighting fixtures

$• 12 months for Labour

This limited warranty is valid only for the original purchaser, is not transferable and is only
applicable to products sold within Australia.

This limited warranty is limited solely to the above, applies only for the period set forth
above, and is contingent upon TLC Global receiving the defective product no later than the
expiration of the applicable warranty period, along with a description of the defect and the
date of its discovery. Warranty claims will not be considered for products received after the
expiration of the applicable warranty period. All warranty claims are judged under the
terms of this limited warranty. A dated proof of purchase must accompany the returned
product.

Warranty claims will not be considered without a dated proof of purchase. Current and
consistent maintenance records must be maintained for all products covered under this
warranty and supplied to TLC Global upon request (proper maintenance guidelines are
detailed in the product technical documentation).

No agent, employee or representative of TLC Global may bind TLC Global to any terms or
conditions beyond the scope of this limited warranty. Any provisions contained in the
purchaser’s purchase order or any other purchaser document which conflict with the terms
and conditions of this limited warranty or which are not expressly set forth in this limited
warranty shall be of no force or effect.

The purchase of this TLC Global product constitutes the purchaser’s acceptance of the
terms set forth in this limited warranty. This warranty gives the purchaser specific legal
rights. The purchaser may also have other rights, which vary from region to region.

B. This limited warranty excludes any defects caused by, resulting from or relating to the
following:

$i. Parts prone to normal wear and tear including lamps, LED’s, fuses, brushes, contact
rings, zippers, lamp sockets and belts;

$ii. misuse, abuse, improper handling, tampering or attempts to repair by or on behalf of
the owner or any person not authorised by TLC Global;

$iii. damage to the product resulting from acts of God;

iv. exposure to harsh or excessively corrosive environmental conditions (whether indoors

or outdoors), including, but not limited to, extreme temperatures, humidity, atmospheric

Page 4

TourPro LED Pin Spot - Manual v1.1