Page 1
Page 2
Disclaimer
Document Part Number: 9002211-001 Rev. 01 (December 2009)
TouchTunes and the TouchTunes logo are trademarks of TouchTunes Interactive Networks.
All other brand and product names are trademarks or registered trademarks of their respective
corporations.
The mention of any product does not constitute an endorsement by TouchTunes Interactive
Networks.
This manual is furnished under a lease agreement and may only be copied or used within
accordance with the terms of such lease agreement. The content of this manual is furnished for
informational use only, is subject to change without notice, and should not be construed as a
commitment by TouchTunes Interactive Networks. TouchTunes Interactive Networks assumes
no responsibility or liability for any errors or inaccuracies that may appear in this document.
Except as permitted by such lease agreement, no part of this publication may be reproduced,
stored in any retrieval system, or transmitted, in any form or by any means, electronic,
mechanical, recording, or otherwise, without prior written consent of TouchTunes Interactive
Networks.
Changes are periodically made to the information herein; these changes will be incorporated
into new editions of this publication. TouchTunes may make improvements and/or changes in
the products and/or software programs described in this publication at any time.
If you have comments on this manual or the products it describes, address them to:
TouchTunes Interactive Networks
Attention: Publications
400 Sainte-Croix Avenue, Suite 200 E
Montreal, Quebec, Canada H4N 3L4
Telephone: 1-847-419-3300
Fax: (847) 419-3304
TouchTunes may use or distribute whatever information you supply in any way it believes
appropriate without incurring any obligations to you.
Copyright © 2009 TouchTunes Interactive Networks. All rights reserved, including those to
reproduce this publication or parts thereof in any form without permission in writing from
TouchTunes Interactive Networks.
Page 3
Table of Contents
1Introduction 5
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Contacting TouchTunes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Hardware Overview and Installation 9
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Speaker Wiring Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Three-channel Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Four-channel Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Amplifier Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
iii
Page 4
iv
Page 5
Introduction
This section introduces the TouchTunes DA415 digital audio amplifier,
provides important safety information, and describes how to get customer
support.
Contents
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Contacting TouchTunes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
About This Guide
This guide is intended for Operators of TouchTunes digital jukeboxes and TouchTunes technical
support and field service personnel. It explains how to install and use the TouchTunes DA415
digital audio amplifier.
This amplifier features:
• Low power consumption.
• High-fidelity signal processing similar to AB type amplifiers.
• Small footprint.
• Overload protection.
• Overheating protection.
5
Page 6
Introduction
The DA415amplifier is available in two versions:
• A 3-channel version, installed in the Mini-Platinum speaker system.
• A 4-channel version, offered in the TouchTunes Ovation model wall-mounted jukebox.
Package Contents
The DA415 package contains the following components:
Part No. Description Quantity
700039-002 DA415 amplifier (3-channel) 1
700039-001 DA415 amplifier (4-channel) 1
300180-026 AC power cable 1
The following accessories for the DA415 amplifier are also available from TouchTunes:
Part No. Description
300142-018 Category 5 cable, RJ45-RJ45
100000-001 Euroblock connector kit
OR
AND
Specifications
• Left channel / Right channel: 150W (RMS), 4 ohms per channel.
• Bridged bass channel: 300W (RMS), total load 8 ohms (3-channel amplifier only).
• Total harmonic distortion: 0.03%.
• Frequency response (all the channels): 20Hz- 20KHz, ± 0.5 dB.
• Stereo sound separation: ≥ 75 dB.
• Signal to noise ratio: ≥ 96 dB.
• Input ± 7V RMS balanced.
• Power: 90 to 130 V AC.
• Maximum power consumption: 1000W.
• Dimensions: Width=230mm, Height=85mm, Depth=330mm.
• Weight: 4.5 kg.
6
Page 7
Important Safety Information
Please read the following important safety information before proceeding with product
installation.
CAUTION: Do not defeat the safety purposes of the polarized or grounding-type
plug. A polarized plug has two blades with one blade wider than the other. A
grounding-type plug has two blades and a third grounding prong. The wider blade
or the third grounding prong are provided for your safety. If the provided plug does
not fit in your outlet, consult an electrician for replacement of the obsolete outlet.
CAUTION: See product enclosure for safety related markings.
CAUTION: To avoid overheating:
• Do not expose the DA415 to excessively high temperatures.
• Do not block the ventilation holes.
• Install the DA415 so that air can circulate freely around it.
CAUTION: Do not use the DA415 immediately after transferring the unit from a cold
place to a warm place as condensation may have occurred on internal components.
Wait for the unit to reach room temperature before using it.
CAUTION: Protect the power cord from being walked on or pinched.
Important Safety Information
WARNING: This symbol alerts you to the presence of “dangerous voltage” within
the product enclosure that may be of sufficient magnitude to constitute a risk of
electrical shock. Do not remove the cover or back. There are no user-serviceable
parts inside. Servicing must be performed by qualified personnel only.
WARNING: To reduce the risk of fire or electric shock, do not expose the DA415 to
rain or moisture.
Contacting TouchTunes
You can contact TouchTunes by:
• Using the links on the Contacts page in the TouchTunes Dashboard. Refer to the following
section.
• Calling TouchTunes by phone. See “Contacting TouchTunes by Phone” on page 8.
7
Page 8
Introduction
Contacting TouchTunes Directly from the Dashboard
You can use the Contacts page in the TouchTunes Dashboard to email many departments at
TouchTunes, including Technical Support.
Using the Contacts page is the easiest way to contact TouchTunes and also allows TouchTunes
to respond to your question, problem or request very quickly. To access the Contacts page,
choose TouchTunes | Contacts and then follow the appropriate email link for the department
you want to contact:
Contacting TouchTunes by Phone
You can also get assistance by calling the TouchTunes Technical Support department toll-free at
1-888-711-5853. If you are outside of the toll-free area, you can still contact the TouchTunes
Technical Support department by dialling 1-847-419-3300 and pressing 1 when prompted.
Note: Long-distance telephone charges may apply if you are calling from outside of the toll-free
area.
8
Page 9
Hardware Overview and Installation
This section provides an overview of the DA415 three-channel and four-
channel amplifiers, and explains important installation procedures.
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Speaker Wiring Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Three-channel Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Four-channel Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Amplifier Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Overview
The TouchTunes DA-415 is a digital audio amplifier that uses
Tripath’s™ Digital Power Processing technology. The DA-415 Is a
Class-T digital amplifier; Class-T is a proprietary technology that
offers both the audio fidelity of Class-AB and the power efficiency of
Class-D amplifiers.
There are two versions of the TouchTunes DA415 digital audio
amplifier:
• A 3-channel amplifier: This ampli
TouchTunes Mini-Platinum speaker system, and supports daisychaining of audio components.
fier is incorporated into the
9
Page 10
Hardware Overview and Installation
• A 4-channel, 2-zone amplifier: This amplifier is currently offered in the TouchTunes Ovation
wall-mounted jukebox.
Features
The DA415 amplifiers incorporate the following features:
Feature/Specification
Class-T Architecture.
Proprietary digital processing technology.
Uncompromising sound quality.
Dynamic range of 102dB.
Over-current protection.
Mute input.
Turn-on and turn-off pop suppression.
Over-temperature protection.
High speed switching power supply.
Less heat, smaller footprint.
Total harmonic distortion ≤ 0.01% (1W).
Signal-to-noise ratio ≥ 100dB (A-weighted).
Two balanced inputs.
One input supporting daisy-chaining.
Four-channel
amplifier
Three-channel
amplifier
Two stereo outputs (full-range).
One stereo output (midrange and high frequencies)
One bass output (low frequency).
AC line voltage and frequency configurations:
90 to 130 V AC
4-ohm (minimum) stereo per channel (150W).
8-ohm per channel (75W).
Benefits of the DA415 amplifier include:
• Requirement of only N-Channel MOSFET output transistors.
• Dramatic improvement in efficiency versus Class AB
amplifiers.
• Signal fidelity equal to high-quality linear amplifiers.
• High dynamic range compatible with digital media.
10
Page 11
Speaker Wiring Guide
Row 1
Row 2
Speaker Wiring Guide
This section provides important information concerning connecting speakers to the DA415 amplifier.
Before continuing with speaker connections, it is strongly recommended that you read this section
thoroughly.
Note: The following examples are applicable to the DA415 4-channel amplifier only.
CAUTION: The DA415 amplifier has been specifically designed for use with 4-ohm
speakers. Using speakers of a lower impedance may cause severe damage to the
amplifier.
Furthermore, if 8-ohm speakers are to be used, they must be wired in parallel in
order to provide a 4-ohm load to the amplifier.
CAUTION: Bose model 141 speakers will not function with either the 3-channel or
4-channel DA415 amplifier. Do not attempt connection of these speakers.
Similarly, wiring two pairs of Bose model 301 speakers in parallel
unsatisfactory performance and may cause damage to your equipment.
will result in
Example 1: TouchTunes 2-Way Speakers
This example illustrates wiring of TouchTunes 2-way speakers (maximum 4 per channel) for a
total impedance load of 4 ohms.
Tou chTun es 2-Way Spea kers W iring
Row (series) impedance specifications
Row 1 2 speakers in series: 4.0 ohms + 4.0 ohms for a total
of 8 ohms per row.
Row 2 2 speakers in series: 4.0 ohms + 4.0 ohms for a total
of 8 ohms per row.
Total impedance specifications
11
Page 12
Hardware Overview and Installation
Row 1
Row 2
Row (series) impedance specifications
Row 1 2 speakers in series: 4.0 ohms + 4.0 ohms for a total
Row 2 2 speakers in series: 4.0 ohms + 4.0 ohms for a total
of 8 ohms per row.
of 8 ohms per row.
Connecting Rows
1 and 2 in Parallel
4.0 ohms total for this combination.
Power over 4 ohms = 150W/channel.
Example 2: Bose 301 Speakers
This example illustrates wiring of Bose 301 speakers (maximum 4 per channel) for a total
impedance load of 6 ohms.
Bose 301 Speakers Wiring
Row (series) impedance specifications
Row 1 2 speakers in series: 6.0 ohms + 6.0
ohms for a total
of 12 ohms per row.
Row 2
2 speakers in series: 6.0 ohms + 6.0 ohms for a total
of 12 ohms per row.
12
Total impedance specifications
Connecting Rows
1 and 2
in Parallel
6.0 ohms total for this combination.
Power over 6 ohms = 100W/channel.
Page 13
Three-channel Amplifier
The DA415 3-channel amplifier is shown in the figure below.
Note: The 3-channel amplifier provides RJ45 input and output connectors to enable daisychaining of components.
Three-channel Amplifier
DA415 Three-channel Amplifier
1. Power connector
Connect the supplied power cord here. The DA415 will automatically start when the power
c
ord is plugged into a wall outlet (AC 120V /60Hz MAX 1000W). There is no power switch.
CAUTION: Do
not connect the AC power cord to a wall outlet until all audio
connections have been completed.
2. Power/Standby light
• Green: Indicates that the DA415 is operating normally.
• Red: Indicates that the amp is in standby or that an abnormal cond
ition has been encountered,
and that protection mode has been activated.
3. Balanced audio input/output connectors
Two RJ45 connectors are provided to connec
t the DA415 to other audio equipment via
standard category 5 cable.
13
Page 14
Hardware Overview and Installation
1
2
3
4
5
6
7
8
white + orange
orange
white + green
blue
white + blue
green
white + brown
brown
white + orange
orange
white + green
blue
white + blue
green
white + brown
brown
1
2
3
4
5
6
7
8
Near
End
Color Color
Far
End
Straight-through catagory 5 cable wiring
RJ45 connector
You can purchase pre-wired cable, or you can wire your own cable as follows:
RJ45 Cable Wiring
4. Left channel audio output connector
Provides audio out at 150W/4 ohms for two satellites using a euroblock connector.
5. Right channel audio output connector
Provides audio out at 150W/4 ohms for two satellites using a euroblock connector.
6. Bass channel audio output connector
Provides audio out at 300W/8 ohms for a subwoofer.
Installation
Please refer to the figure on page 13 while performing the installation.
1. Ensure that the power supply cord is disconnec
amplifier.
2. Connect a standard category 5 cable with RJ45 co
MJS to the input connector (3) on the DA415 amplifier.
3. Connect the left and right Mini-Platinum satelli
euroblock connectors firmly into the left and right channel audio output connectors (4 and 5)
on the DA415 amplifier.
4. Connect the Mini-Platinum subwoofer to the DA415
channel audio output connector (6) on the amplifier.
CAUTION: Inco
severe damage to the amplifier. If you have not already done so, please refer to
“Speaker Wiring Guide” on page 11 before proceeding.
5. Op
tional: Connect the DA415 to other audio equipment (for example, a second Mini-
Platinum speaker system) using a standard category 5 cable with RJ45 connectors.
6. Power up the unit by connecting the power c
(AC 120V /60Hz MAX 1000W) and the power connector on the amplifier.
ted from the power connector on the DA415
nnectors from the Zone 1 output on the
te speakers to the DA415 by pressing their
by pressing the connector into the bass
rrect speaker installation or speaker wiring configuration can cause
ord between a properly grounded wall outlet
14
Page 15
Four-channel Amplifier
The DA415 4-channel amplifier is shown in the figure below.
DA415 Four-channel Amplifier
Four-channel Amplifier
Unlike the 3-channel model, the 4-channel amplifier does not support daisy-chaining of
components; the RJ45 connectors for Zones A and B are both inputs.
Amplifier Connectors
15
Page 16
Hardware Overview and Installation
1
2
3
4
5
6
7
8
white + orange
orange
white + green
blue
white + blue
green
white + brown
brown
white + orange
orange
white + green
blue
white + blue
green
white + brown
brown
1
2
3
4
5
6
7
8
Near
End
Color Color
Far
End
Straight-through catagory 5 cable wiring
RJ45 connector
1. Power connector
Connect the supplied power cord here. The DA415 will automatically start when the power
c
ord is plugged into a wall outlet (AC 120V /60Hz MAX 1000W). There is no power switch.
2. Power/Standby light
• Green: Indicates that the DA415 is operating normally.
CAUTION: Do
not connect the AC power cord to a wall outlet until all audio
connections have been completed.
• Red: Indicates that the amp is in standby or an abnor
mal condition has been encountered and
that protection mode has been activated.
3. Zone A and Zone B audio input connectors
Two RJ45 connectors are provided to connect the DA415 to the Zone A and Zone B audio
outputs of
You can purchase pre-wired cable, or y
RJ45 Cable Wiring
the MJS via standard category 5 cable.
ou can wire your own cable as follows:
4. Zone A left and right channel audio output connectors
Provides audio out at 150W/4 ohms for Zone
A speakers using a euroblock connector.
5. Zone B left and right channel audio output connectors
Provides audio out at 150W/4 ohms for Zone
Installation
Note: With its inputs and outputs for 2 independent zones, the DA415 4-channel amplifier is
significantly different from the 3-channel version, and involves a different method for speaker
connection. Please pay careful attention to the following connection instructions.
16
Please refer to the figure on page 15 while performing the installation.
1. Ensure that the power supply cord is disconnec
amplifier.
A speakers using a euroblock connector.
ted from the power connector on the DA415
Page 17
Amplifier Conversion
2. Connect a standard category 5 cable with RJ45 connectors from the Zone 1 output on the
MJS to the Zone A input connector on the DA415 amplifier.
CAUTION: Inco
rrect speaker installation or speaker wiring configuration can cause
severe damage to the amplifier. If you have not already done so, please refer to
“Speaker Wiring Guide” on page 11 before proceeding.
3. Connect left and right speakers to the DA415 by pr
into the left and right channel audio output connectors for Zone A on the DA415 amplifier.
4. Op
tional: Connect a standard category 5 cable with RJ45 connectors from the Zone 2 output
on the MJS to the Zone B input connector on the DA415 amplifier.
5. Op
tional: Connect left and right speakers to the DA415 by pressing their euroblock
connectors firmly into the left and right channel audio output connectors for Zone B on the
DA415 amplifier.
6. Power up the unit by connecting the power c
(AC 120V /60Hz MAX 1000W) and the power connector on the amplifier.
Amplifier Conversion
It is possible to convert a DA415 amplifier from a 3-channel to a 4-channel version, and viceversa, by changing the amplifier’s I/O board. Such a procedure should be undertaken by
qualified service personnel only.
Note: TouchTunes does not recommend replacing a DA415 amplifier’s I/O board with that of a
different version, as complications may ensue should the amplifier require subsequent
servicing.
essing their euroblock connectors firmly
ord between a properly grounded wall outlet
For technical information and replacement parts, please contact TouchTunes.
17
Page 18
Hardware Overview and Installation
18
Page 19
Copyright © 2009 TouchTunes Interactive Networks
TouchTunes Interactive Networks, Inc.
400 Sainte Croix Avenue, Suite 200 E
Montreal, Quebec,
Canada, H4N 3L4
TouchTunes Interactive Networks, Inc.
3455 Salt Creek Lane, Suite 100
Arlington Heights, IL 60005
USA
Technical Support
847-353-1954
www.touchtunes.com
Page 20
Loading...