Thank you for purchasing this projector.
WARNING
After reading them, store them in a safe place for future reference.
About this manual
Various symbols are used in this manual. The meanings of these symbols are
WARNING
This symbol indicates information that, if ignored, could possibly
This symbol indicates information that, if ignored, could possibly
Please refer to the pages written following this symbol.
• The information in this manual is subject to change without notice.
without express written consent.
Trademark acknowledgment
All other trademarks are the properties of their respective owners.
About this manual
. . . . . . . . . .
. . . . . . . . . . . . . . . . . .
2
. . . . . . . . . .
About contents of package
. . . . . . . . . . . . . . .
4
. . . . . . . . . . . . . . . . . . . . .
4
. . . . . . . . . . . . . . . .
Arrangement
Adjusting the projector's elevator
. .
About the fi lter cover for bottom-up use
. .
. . . . . . . .
. . . . . . . .
. . . . . . . . . . . . .
Turning on the power
. . . . . . . . . . .
Turning off the power
Adjusting the volume
Temporarily muting the sound
. . . .
. . . . . . . .
. . . . . . . .
Adjusting the zoom and focus
Adjusting the position
. . . . . . . . . .
20
. . . . . . .
20
Temporarily blanking the screen
. . . . . . . .
22
Content
Content
. . . . . . . . . . . . . . . . . .
23
Aspect, Mode, Brightness, Contrast,
. . . . . . . . . . . . . . .
25
28
Aspect, Over scan, V. position, H. position,
Whisper, Mirror, Volume, Audio
. . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
Auto
search, Auto off, Lamp time,
. . . . . . . . . . . . .
Air fi lter
40
Troubleshooting
. . . . . . . . . .
42
. . . . . . . . . . . . .
42
. . . .
44
46
Warranty and after-service
48
. . . . . . . . . . . .
48
To avoid losing the lens cover, please fasten it the lens cap to the projector using
the strap.
Projector features / Preparations
Projector features
This projector is used to project various computer signals as well as NTSC/PAL/
High Brightness
Low Noise
WHISPER mode is available for reducing acoustic noise to realize quieter
Compact Body
which gives you more fl exibility and usability to use it where you want.
Preparations
About contents of package
• Keep the original packing materials for future reshipment. For
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDEO
COMPONENT VIDEO
CB/PB
CR/PR
R-AUDIO 2-L
AUDIO-OUT
Part names
Zoom knob (
Zoom knob (
Vent (
AC inlet (
VIDEO ports (
/P
/P
VIDEO port (
Part names
Vent (
AUDIO-OUT port (
AUDIO 1-IN port (
AUDIO 2 L/R port (
This projector is controlled by an internal
turning on again, make the projector cool down at least 10 minutes without
46
VIDEO button (
ASPECT button (
ON button (
OFF button (
Part names
44,45
TEMP indicator (
44,45
AUTO button (
VOLUME button (
VIDEO
RG
B
SEARC
H
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTER
MENU
RESE
T
Setting up
Setting up
WARNING
wobbly or inclined stand.
the air fi lter.
The high temperature of the projector could cause a fi re, a burn and/or
walls.
place the projector near a humidifi er, a smoking space or a kitchen.
Arrangement
The values shown in the table are calculated for a full size screen: 1024 x 768
Setting up
4:3
size
4 : 3 screen
down
down
40648
8
69
2.0
60
60
2.2
2.0
2.4
-2
2.1
2.6
2.3
2.8-384
80
2.9
2.6
-3
4.0
-4
4.0
4.8
-5
4.623206
6.0
-6
200
6.1
274
6.7
-8
241
250
8.4
-10
46
size
4 : 3 screen
down
down
41
-1
40648
8692.0-260
60
2.2
2.0
2.4
-2
2.5
2.3
2.8-384
80
2.9
-3
2.7
-4
4.0
4.0
4.8
-5
4.6
23
206
6.0
-6
200
6.1
274
6.7
-8
241
250
8.4
-10
46
411
-12
Adjusting the projector's elevator
WARNING
the projector might crash down, overturn, smash your fi ngers and possibly
To prevent damaging the projector and injuring yourself,
You can use the elevator feet to make adjustments if the surface on which you
After making sure that the projector is cool adequately, press and hold in the
The elevator buttons and the elevator feet are on the both sides.
When you release the elevator buttons, the elevator feet will lock into position.
the elevator feet by hand.
Setting up
Setting up
About the fi lter cover for bottom-up use
WARNING
the power switch is off and the power cord is not plugged in, then wait at least
45 minutes.
When the projector is installed bottom up, please use the accessory fi lter cover
for bottom-up use. It is higher than usual fi lter cover, to keep the space for intake
ventilation. Please change the fi lter cover in the following procedure.
After making sure that the projector is cool adequately,
To set
To remove
Setting up
Attempting to connect a live device to the projector may generate extremely
to the device and/or projector
•
Whenever attempting to connect a laptop computer to the projector, be sure
to activate the laptop’s RGB external image output (set the laptop to CRT display or to
simultaneous LCD and CRT display). For details on how this is done, please refer
to the
on Windows. Then the resolution will go back to the original. It might be recommended
to use other CRT or LCD monitors to change the resolution.
About Plug-and-Play capability
2B. Plug-and-Play can be achieved by connecting this projector to a computer is VESA
type of connection is attempted.
Setting up
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDE
O
COMPONENT VIDEO
CB/P
B
CR/P
R
R-AUDIO 2-L
AUDIO-OU
T
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDE
O
COMPONENT VIDEO
CB/P
B
CR/P
R
R-AUDIO 2-L
AUDIO-OU
T
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDE
O
COMPONENT VIDEO
CB/P
B
CR/P
R
R-AUDIO 2-L
AUDIO-OU
T
RGB IN2
RGB OUT
Audio out
Audio in
* For the audio input, please refer to
the AUDIO item in the SETUP menu.
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDEO
COMPONENT VIDE
O
CB/P
B
CR/P
R
R-AUDIO 2-L
AUDIO-OU
T
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDE
O
COMPONENT VIDE
O
CB/P
B
CR/P
R
R-AUDIO 2-L
AUDIO-OU
T
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDE
O
COMPONENT VIDE
O
CB/P
B
CR/P
R
R-AUDIO 2-L
AUDIO-OU
T
Y
VIDEO
RGB IN1 RGB IN2
RGB OUT CONTROL
AUDIO 1-IN
S-VIDE
O
COMPONENT VIDE
O
CB/P
B
CR/P
R
R-AUDIO 2-L
AUDIO-OU
T
Setting up
Audio (L) out
Video out
Audio cable
Audio/Video cable
Audio (L) out
Audio (L) out
Y
/P
/P
Audio cable
Audio (R) out
Audio (R) out
/P
/P
Audio (R) out
Setting up
WARNING
your dealer to newly get correct one.
AC inlet
of the power cord
WARNING
Always handle the batteries with care and use them only as
which could result in fi re, injury and/or pollution of the surrounding environment.
types at the same time. Do not mix a new battery with used one.
Align and insert the two AA batteries according to their plus and minus
terminals as indicated in the remote control.
Remote control
Remote control
you won’t be using the remote control for an extended period.
The remote control works with the projector’s remote sensor.
to the left and right of the remote sensor).
to send a remote signal to the sensor directly, please try to use the refl ected signal.
that could block the remote control’s output signal to the projector.
Remote control
Power on/off
Power on/off
WARNING
When the power is on, a strong light is emitted. Do not look into
the lens of projector. Also do not peep at the inside of projector through a hole.
Turn the power on/off in right order. Please power on the projector prior
to the connected devices. Power off the projector later than the connected devices.
Turning on the power
the ON position.
The power indicator will light up in steady orange. Then
wait several seconds because the buttons may not
function for these several seconds.
The projector lamp will light up and the POWER indicator will begin blinking
To display the picture, select an input signal according to the section "Selecting an
Turning off the power
The message "Power off?" will appear on the screen for
The projector lamp will go off, and the POWER indicator
will begin blinking in orange.
Then the POWER indicator will stop blinking and light in
switch to the OFF position. The POWER indicator will go off. Attach the lens cover.
VIDEO
RG
B
SEARC
H
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
Operating
Operating
Adjusting the volume
A dialog will appear on the screen to aid you in adjusting the
volume.
To close the dialog and complete the operation, press the VOLUME button
Temporarily muting the sound
A dialog will appear on the screen indicating that you have
To restore the sound, press the MUTE or VOLUME button. Even if you don’t do
RGB IN1
RGB IN2
VIDEO
S-VIDEO
COMPONENT VIDEO
RGB IN2
RGB IN2
S-VIDEO
VIDEO
VIDEO
RGB
SEARC
H
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
VIDEO
RG
B
SEARC
H
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
KEYSTONE
VIDEO
RG
B
SEARC
H
ASPECT AUTO
BLAN
K
VIDEO
RG
B
SEARC
H
ASPECT AUTO
BLAN
K
Operating
Adjusting the zoom and focus
4:3
16:9
4:3
16:9
SMALL
VIDEO input, only 16:9 mode can be selected.
VIDEO
RG
B
SEARC
H
MAGNIFY
ASPECT AUTO
BLAN
K
VOLUME
Zoom knob
The projector will start to check its input ports in order to
fi nd any input signals.
Then when an input is found, the projector will stop
the projector will return to the state selected before the
RGB IN 2
COMPONENT VIDEO
S-VIDEO
VIDEO
VIDEO
RGB
SEARC
H
ASPECT AUTO
BLAN
K
Operating
The vertical position, the horizontal position, the clock phase
And the aspect ratio will be automatically selected. Make sure that the
feature. A dark picture may still be incorrectly adjusted. Use a bright picture
when adjusting.
The video format
This function is available only when the AUTO mode is selected to the
VIDEO FORMAT item in the INPUT menu
function.
The vertical position and horizontal position will be automatically adjusted.
The aspect ratio will be automatically selected.
The clock phase will be automatically adjusted.
Adjusting the position
The “POSITION” indication will appear on the screen.
When you want to reset the operation, press the RESET button on the remote
To complete this operation, press the POSITION button again. Even if you don’t
VIDEO
RG
B
SEARC
H
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
KEYSTONE
POSITION
ENTE
R
MENU
VIDEO
RG
B
SEARC
H
MAGNIFY
ASPECT AUTO
BLAN
K
VOLUME
20
The “MAGNIFY” indication will appear on the screen
To move the zoom area, press the POSITION button in the MAGNIFY mode,
then use the cursor buttons ▲/▼/◄/► to move the area. And to fi nalize the
zoom area, press the POSITION button again.
To exit the MAGNIFY mode and restore the screen to normal, press the OFF
will be restored when the projector exits the MAGNIFY mode.
Operating
To close the dialog and complete this operation, press the
VIDEO
RG
B
SEARC
H
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
KEYSTONE
VIDEO
RG
B
SEARC
H
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
The “FREEZE” indication will appear on the screen, and the
To exit the FREEZE mode and restore the screen to normal,
too long.
Temporarily blanking the screen
The blank screen will be displayed instead of the screen of
To exit the blank screen and return to the input signal screen, press the
signal is changed, or when one of the projector’s buttons or the remote control
Operating
VIDEO
RG
B
SEARC
H
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
KEYSTONE
VIDEO
RGB
SEARC
H
MAGNIFY
ASPECT AUTO
BLAN
K
VOLUME
VIDEO
RGB
SEARCH
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLANK
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
VIDEO
RG
B
SEARCH
FREEZE
OFF
ON
MAGNIFY
ASPECT AUTO
BLAN
K
MUTE
VOLUME
KEYSTONE
POSITION
ES
C
ENTE
R
MENU
RESE
T
Operating
Multifunctional settings
This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN,
The basic operations of these menus are as follows.
the cursor buttons on the projector.
The Advanced MENU or EASY MENU will appear.
4.
Then press the cursor button ► on the projector or remote
Then press the cursor button
on the projector or remote control, or the ENTER button
on the remote control to progress. The operation menu of the selected item will appear.
4.
When you want to reset the operation, press the RESET button on the remote
simultaneously with operation (ex. LANGUAGE, H PHASE etc.) cannot be reset.
on the projector or remote control, or the ESC button on the remote control.
when a certain input signal is displayed.
EASY MENU
CONTRAST
ASPECT 4:3
BRIGHTNESS
MODE NORMAL
COLOR
+0
+0
+0
TINT
+0
SHARPNESS
+3
WHISPER NORMAL
RESET
FILTER TIME 0
LANGUAGE ENGLISH
Go To Advance Menu...
MIRROR NORMAL
MENU [RGB]
IMAGE
SETUP
PICTURE
INPUT
OPTION
SCREEN
SHARPNESS +0
BRIGHTNESS ＋0
CONTRAST ＋0
COLOR +0
TINT +0
COLOR TEMP 6500K
GAMMA DEFAULT 1
MY MEMORY SAVE 1
:SELECT
EASY MENU
PROGRESSIVE TURN OFF
23
Multifunctional settings
EASY Menu
ASPECT
of picture type. The
CINEMA
When the combination of GAMMA and COLOR TEMP differs from
TEMP (
PICTURE menu.
in the
menu
of section
menu
menu
TINT
TINT item in the
menu
menu
WHISPER
WHISPER item in the
menu
With the EASY MENU, items shown in the table below can
following table.
EASY MENU
CONTRAST
ASPECT 4:3
BRIGHTNESS
MODE NORMAL
COLOR
+0
+0
+0
TINT
+0
SHARPNESS
+3
WHISPER NORMAL
RESET
FILTER TIME 0
LANGUAGE ENGLISH
Go To Advance Menu...
MIRROR NORMAL
Multifunctional settings
menu
A dialog is displayed for confi rmation. Selecting RESET using the
of the air fi lter.
A dialog is displayed for confi rmation. Selecting RESET using the
menu
to toggle the menu language.
description of
in the
menu
Advanced Menu
or
OPTION.
25
Multifunctional settings
PICTURE Menu
: Light
Dark
Weak
ons ▲/▼ switches the
#1 DEFAULT
#1 CUSTOM
#2 DEFAULT
#3 CUSTOM
#3 DEFAULT
#2 CUSTOM
To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM
or the ENTER button
displays a dialog to aid you in adjusting the
This function is useful when you want to
using the buttons ◄/►, and
Y
ou can display a test pattern for checking the effect of your
No pattern
Gray scale of 9 steps
Ramp
Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the
test pattern except the darkest in the left end. If you want to adjust
the 2nd tone from left end on the test pattern, use the equalizing
When this fun
With the PICTURE menu, the items shown in the table
1
+0
2
+0
3
+0
4
+0
5
+0
6
+0
7
+0
8
+0
GAMMA [CUSTOM 1
]
ENTER :
MENU [RGB]
IMAGE
SETUP
PICTURE
INPUT
OPTION
SCREEN
SHARPNESS +0
BRIGHTNESS ＋0
CONTRAST ＋0
COLOR +0
TINT +0
COLOR TEMP 6500K
GAMMA DEFAULT 1
MY MEMORY SAVE 1
:SELECT
EASY MENU
PROGRESSIVE TURN OFF
26
Multifunctional settings
LOW
CUSTOM
To adjust CUSTOM
the
CUSTOM and then pressing the
displays
dialog
to aid you in adjusting the OFFSET and/or GAIN
of the CUSTOM mode.
on the whole tones of the test pattern.
on the brighter tones of the test pattern.
the buttons ▲/▼.
You can display a test pattern for checking the effect of your
No pattern
Gray scale of 9 steps
Ramp
Gray scale of 15 steps
Whe
strength of whole color.
Weak
This item can be selected only for a video signal
tint.
Red
This item can be selected only for a video signal
sharpness
Weak
R
+0
G
+0
B
+0
COLOR TEMP
ENTER :
OFFSET
R
+0
G
+0
B
+0
GAIN
Multifunctional settings
TURN OFF
This function is performed only for an interlaced signal of a VIDEO
When TV or FILM is selected, the screen image will be sharp.
for a quick moving object. In such a case, please select TURN OFF,
LOAD2
LOAD3
LOAD4
SAVE2
SAVE1
This projector has 4 numbered memories for adjustment data.
the memory whose number corresponds to the c
ommand’s
number,
The current
adjustment data of the items in the PICTURE menu is
stored, except for the adjustment data in the CUSTOM modes for
the GAMMA and COLOR TEMP items.
28
Multifunctional settings
IMAGE Menu
ASPECT
4:3
16:9
NORMAL
a
video signal / no signal
4:3
16:9
SMALL
The NORMAL mode keeps the original aspect ratio of the signal.
HDTV signal of 1125i (1080i)
or 750p (720p)
as the
this item can't be selected.
setting.
over-scan ratio
Small (It magnifi es picture)
This item can be selected only for a video signal
When this adjustment is too large, certain degradation may appear
V POSITION
Down
Right
fl icker.
Left
This item can be selected only for an RGB signal or a component
video signal.
video port
With the IMAGE menu, items shown in the table below can
MENU [RGB]
IMAGE
PICTURE
:SELECT
AUTO ADJUST EXECUTE
ASPECT 4:3
OVER SCAN 5
H PHASE 16
H SIZE 1344
H POSITION 142
V POSITION 25
SETUP
INPUT
OPTION
EASY MENU
SCREEN
29
Multifunctional settings
This item can be selected only for an RGB signal
When this adjustment is excessive, the picture may not be
displayed correctly. In such a case, please reset the adjustment
operation.
AUTO ADJUST
RGB signal
The vertical position, the horizontal position, the clock phase and
the horizontal size will be automatically adjusted. And the aspect
a
video signal or s-video signal
The video format best suited for the respective input signal will be
selected automatically.
This function is available only when the AUTO mode is selected to
the VIDEO FORMAT item in the INPUT menu. For a component
video signal, the signal type is identifi ed automatically independently
of this function.
The vertical position and horizontal position will be automatically
The aspect ratio will be automatically selected.
The clock phase will be automatically adjusted.
The automatic adjustment operation requires approximately 10
seconds. Also please note that it may not function correctly with
some input.
Multifunctional settings
INPUT Menu
AUTO
RGB
SMPTE240
REC709
REC601
This item can be selected only for an RGB signal or a component
video signal
video port)
The AUTO mode automatically selects the optimum mode.
The AUTO operation may not work well at some signals. In such a
function of COMPONENT
VIDEO port
SCART RGB
When the SCART RGB is selected, the COMPONENT VIDEO port
function as a port for a SCART RGB signal input.
A SCART adapter
details, contact your dealer.
VIDEO FORMAT
t
AUTO
PAL
This item is performed only for a video signal from the VIDEO port
or the S-VIDEO port. For a component video signal, the signal type
The AUTO mode automatically selects the optimum mode
The AUTO operation may not work well for some signals. If the
With the INPUT menu, the items shown in the table below
MENU [RGB]
IMAGE
SETUP
PICTURE
INPUT
OPTION
EASY MENU
SCREEN
:SELECT
VIDEO FORMAT AUTO
COLOR SPACE AUTO
INFORMATION
COMPONENT COMPONENT
Multifunctional settings
displays a dialog titled “INPUT INFORMATION”.
-INFORMA
TION
RGB
0
FRAME LOCK
-INFORMA
TION
S-VIDEO
SECAM
AUT
O
-INFORMA
TION
COMPONENT
576i @50
SCART RGB
The “FR
AME LOCK” message on the dialog means the frame lock
function is working
This function automatically works when a RGB
signal with vertical frequency of 50 to 60 Hz is input, and it displays
The “SCART RGB” message means the COMPONENT VIDEO
port. Please refer
to the
This item
for
no signal and sync out.
Multifunctional settings
SETUP Menu
WHISPER
turns off/on the whisper mode
WHISPER
When the WHISPER is selected, acoustic noise and screen
H:INVERT
V:INVERT
H&V:INVERT
VOLUME
AUDIO
with the input port using the buttons
(2).
When off is selected, both of two audio ports
do not work for the input port.
RGB2
COMPONENT
S-VIDEO
VIDEO
2
With the SETUP menu, the items shown in the table below
MENU [RGB]
IMAGE
SETUP
PICTURE
INPUT
OPTION
EASY MENU
SCREEN
:SELECT
WHISPER NORMAL
MIRROR NORMAL
AUDIO
VOLUME 16
AUDIO
RGB2
QUIT
RGB1
S‑VIDEO
VIDEO
COMPONENT
1 2
Multifunctional settings
SCREEN Menu
POLSKI
TÜRKÇE
FRANÇAIS
DEUTSCH
ESP
AÑOL
I
TA
NEDERLANDS
POR
TUGUÊS
SVENSKA
To quit the operation, press the MENU button on the remote control
or keep no operation for 10 seconds.
DARK
The blank screen is a screen
for the temporarily blanking feature
ORIGINAL
To avoid remaining as an afterimage, the MyScreen and the
With the SCREEN menu, the items shown in the table
MENU [RGB]
IMAGE
SETUP
PICTURE
INPUT
OPTION
EASY MENU
SCREEN
:SELECT
LANGUAGE ENGLISH
MENU POSITION
START UP ORIGINAL
OSD BRIGHT. 5
MyScreen
MyScreen Lock TURN OFF
MESSAGE TURN ON
BLANK BLACK
Multifunctional settings
the
The start-up screen is a screen displayed when no signal or an
ORIGINAL
TURN OFF
To avoid remaining as an afterimage, the MyScreen and the
will change to the BLACK screen.
below
the BLANK screen,
item
This item functions for capturing the MyScreen of the blank screen
you if you start capturing the picture from the current screen.
the ENTER button on the remote control when the picture is
displayed. The picture will freeze and the frame for capturing
To stop performing, press the RESET or ESC button on the
2. Using the buttons ◄/►/▲/▼ adjusts the frame position. Please
To start registration, press the ENTER button on the remote
To restore the screen and return to the previous dialog, press the
several
minutes. When the registration is
turns on/off the MyScreen lock function
TURN ON
TURN OFF
When the TURN ON is selected, the item MyScreen is locked. Use
this function for protecting the current MyScreen.
Multifunctional settings
t
TURN ON
TURN OFF
When the TURN ON is selected, the following message function
works.
”NO INPUT IS DETECTED”
”SYNC IS OUT OF RANGE”
while searching for the input
The indication of the input signal displayed by changing
The indication of the aspect ration displayed by changing
The indication of
When the TURN OFF is selected
freezing for a malfurction
Multifunctional settings
OPTION Menu
AUTO SEARCH
turns on/off the
automatic signal search
function
TURN ON
TURN OFF
This function works with INPUT, RGB, and VIDEO buttons.
When the TURN ON is selected, detecting no signal automatically
the following order
started from the current port.
Then
when an input is found, the
S-VIDEO
VIDEO
AUTO OFF
time to count down to
Short (min. 0 minute = DISABLE)
AUT
O OF
AUT
O OF
F
DISABLE
0
When the time is set to 0, the projector is not turned off automatically.
When the time is set to 1 to 99, and when the passed time with no-
signal or an unsuitable signal reaches at the set time, the projector
The lamp time is the time counted after the last resetting. It is
shown in the OPTION menu as the usage time of the lamp.
or the button
of the projector
displays
To reset the lamp time
select the
CANCEL
only when you have replaced the lamp
for a corresponding message about the lamp
the lamp
(
The
fi lter time
is the time counted after the last resetting. It is shown
time of the
or the button
of the projector
displays a dialog. To reset the fi lter time, select the
CANCEL
replaced
the
the
see the section "
Air fi lter
40
With the OPTION menu, the items shown in the table below can
or remote control, or the ENTER button on the remote control to
TIME. T
MENU [RGB]
PICTURE
:SELECT
IMAGE
SETUP
INPUT
OPTION
EASY MENU
SCREEN
AUTO OFF 0
LAMP TIME 0
FILTER TIME 0
AUTO SEARCH TURN OFF
SERVICE
Multifunctional settings
the
the ENTER button on the remote control to
AUTO ADJUST
GHOST
otation speed of the cooling
fans. The HIGH is the mode for use at highlands etc.
AUTO ADJUST
the buttons ▲/▼
/disables
the
When DISABLE is selected, the automatic adjustment feature is
disabled, although rough adjustment is automatically performed
depending on the basic setting.
disable the automatic adjustment, and make adjustment manually.
2.
Adjust the selected element using the buttons ▲/▼ to disappear ghost.
Adjust the selected element using the buttons ▲/▼ to disappear ghost.
turns on/off the key lock feature. When TURN ON is
selected, the buttons on the projector except the STANDBY/ON button are locked.
TURN ON
TURN OFF
function does not have any effect on the remote control.
200h
300h
TURN OFF
50h
After selecting “50h”, 100h”, “200h”, or “300” , the message “CLEAN
THE AIR FILTER” will appear after the timer reaches the interval
time set by the menu. Please refer to the “FILTER TIME” item
and the table “Related message”
42
When the “TURN OFF” is chosen, the air-fi lter cleaning message will not appear.
with the operating environment of the projector and the condition of air
fi lter, especially when the “200h”, “300h” or “TURN OFF” is chosen.
all the items in all of menus will collectively return to the
ote
that the items LAMP TIME, FILTER TIME and LANGUAGE are not reset.
CANCEL
Maintenance
Maintenance
WARNING
The projector uses a high-pressure mercury glass lamp. The lamp can
with a loud bang, or burn out
with a loud bang, or burn out
to fl y into the lamp housing, and for
to escape from the projector’s vent holes.
About disposal of a lamp
• This product contains a mercury lamp; do not
the US) or www.epsc.ca (in Canada).
the power cord from the outlet, and make sure to request a replacement
try to clean the projector or replace the lamp yourself.
ventilate the room well, and make sure not to breathe the gas that
Never unscrew except the appointed (marked by an arrow) screws.
the ceiling. This is dangerous, since if the lamp’s bulb has broken, the
that there are electrical problems elsewhere besides the lamp. If this
the section "Related Messages" and "Regarding the indicator Lamps"),
the plug
from the
outlet
When the indicators or a message prompt you to replace the lamp, replace the
Turn the projector off, and unplug the power cord. Allow the lamp to cool for
To prepare a new lamp, contact your dealer and tell the lamp type number
After making sure that the projector has
the lamp, and slowly pick up the lamp by the
two screws that are loosened in the previous
While interlocking the 2 tabs of the lamp
the two claws to fi x the lamp cover.
facing up.
Turn the projector on, and reset the lamp
time using the LAMP TIME function in the
(
• When the lamp has been replaced after the message of "THE
Maintenance
of claws
Tabs
40
Maintenance
When the indicators or a message prompts you to clean the air filter, clean the air filter
Turn the projector off, and unplug the power cord.
Allow the projector to cool for at least 45 minutes. And
After making sure that the projector is cool adequately,
the projector is placed lens-side up, hold the projector.
Apply a vacuum cleaner to the vent of the projector for the
Apply a vacuum cleaner to the air fi lter and the fi lter cover.
To prepare a new air fi lter, contact your dealer and tell the air
fi lter type number =
An air fi lter of specifi ed type will come even with a replacement lamp for this projector.
Turn the projector on, and reset the fi lter time using the FILTER TIME
function of the OPTION menu
(
WARNING
then allow
the projector to cool suffi ciently
The
Avoid wetting the projector or inserting liquids in the projector. It could result
Air fi lter
Air fi lter
Air fi lter’s knob
Maintenance
WARNING
►Before caring, make sure the power switch is off and the
The care in a high temperature state of the projector could cause a burn and/or
following. Incorrect care could cause not only an injury but adverse infl uence
Turn the projector off, and unplug the power cord. Allow the projector to cool
suffi ciently.
After making sure that the projector is cool adequately, lightly wipe the lens
with a commercially available lens-cleaning wipe. Do not touch the lens
Turn the projector off, and unplug the power cord. Allow the projector to cool
suffi ciently.
After making sure that the projector is cool adequately, lightly wipe with gauze
Troubleshooting
Troubleshooting
When the unit's power is on, messages such as those shown below may be
service company.
Although these messages will be automatically disappeared around several
CHANGE THE LAMP.
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
The time the lamp timer has counted is approaching
2000 hours.
sure to reset the lamp timer
CHANGE THE LAMP.
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL
BE
TURNED OFF ** hrs later.
The time the lamp timer has counted is approaching
2000 hours, so a lamp change within
**
hours is
When lamp usage reaches 2000 hours, the power will
CHANGE THE LAMP.
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL BE
TURNED OFF 0 hrs later.
As the time the lamp timer has counted has reached
2000 hours, the power will soon be automatically
turned off.
ON ***
There is no input signal.
of the signal source.
SYNC IS OUT OF RANGE
ON *** fH *****kHz fV *****Hz
The horizontal or vertical wavelength of the input signal
source specs.
43
Troubleshooting
CHECK THE AIR FLOW
The internal temperature is rising.
down at least 20 minutes. After having confi rmed the
following items, please turn the power ON again.
•
•
set FAN SPEED of the SERVICE item in the OPTION menu
to HIGH.
REMINDER
*** HRS PASSED AFTER THE
LAST FILTER CHECK.
FILTER MAINTENANCE IS ESSENTIAL
TO REMOVE WARNING MESSAGE,
RESET FILTER TIMER.
SEE MANUAL FURTHER INFO.
A note of precaution when cleaning the air fi lter.
the air fi lter referring to the “Air Filter” section of this manual.
After you have cleaned or changed the air fi lter, please be
sure to reset the fi lter timer
40
• A lamp has a fi nite product life. Lamps are characterized by the
fact that, after long hours of usage, a lamp will no longer light up, or the lamp
will break or burst, etc. This projector is equipped with an automatic shut-down
function, such that the power will automatically be turned off when lamp usage
time has reached 2000 hours. Please be aware, however, that among lamp
types, there are major differences in product lifetimes; a lamp may thus fail to
Troubleshooting
TEMP
Orange
Turned
Turned
The projector is in a standby state.
Green
Turned
Turned
The projector is warming up.
Green
Turned
Turned
The projector is in an on state.
Orange
Turned
Turned
The projector is cooling down.
Red
tionary)
tionary)
The projector is cooling down. A certain error
the item descriptions below.
Red
Red
Red
Turned
The lamp does not light, and there is a
suffi ciently cooled down, please make confi rmation of
the following items, and then turn the power on again.
Red
Red
Red
Turned
The lamp cover has not been properly fi xed.
to
After the projector has
suffi ciently cooled down, please make confi rmation
of the attachment state
of the lamp cover.
After
on again.
the
45
Troubleshooting
TEMP
Red
Red
Turned
Red
The cooling fan is not operating.
to
After the projector has
suffi ciently cooled down, please make confi rmation
that no foreign matter has become caught in the fan,
Red
Red
Turned
Red
There is a possibility that the interior portion
to
suffi ciently cooled down, please make confi rmation of
the following items, and then turn the power on again.
Green
Alternative
blinking in
Red
There is a possibility that the interior portion
within the usage temperature
Green
blinking in
Red
fi lter
After cleaning or changing
the air fi lter
to reset the fi lter timer. After the remedy, reset the
• When the interior portion has become overheated, for safety
46
Troubleshooting
WARNING
the power outlet. After making sure that the smoke or odor has stopped, contact
your dealer or service company.
This operation sometimes resolves your problem.
The projector’s microprocessor may need to be reset. Please push the
(
to reset all settings to factory default.
Then, if the problem is not removed after the remedy, please contact your dealer
The electrical power cord is not plugged in.
The power switch is not set to the on position.
The main power source has been interrupted during
down at least 20 minutes. After the projector has suffi ciently
at least 45 minutes. After the projector has suffi ciently cooled
down, please make confi rmation of the attachment state of the
The signal cables are not correctly connected.
The MUTE function is working.
on the remote control.
The volume is adjusted to an extremely low level.
Adjust the volume to a higher level using the menu function
or the remote control.
The AUDIO setting is not correct.
displayed.
The
is attached.
the lens
4, 16
The signal cables are not correctly connected.
The brightness is adjusted to an extremely low level.
Adjust BRIGHTNESS to a higher level using the menu
function
or the remote control
23, 25
The computer cannot detect the projector as a plug
Video screen
display freezes.
The FREEZE function is working.
21
faded- out
TEMP,
TINT and/or
settin
gs,
2
dark.
The brightness and/or contrast are adjusted to an
extremely low level.
Adjust BRIGHTNESS and/or CONTRAST settings to a
The WHISPER function is working.
2
The lamp is approaching the end of its product
Adjust the focus using t
PHASE
The lens is d
or ts
41
Troubleshooting
• Although bright spots or dark spots may appear on the screen, this
48
Warranty And After-Service
Warranty and after-service
through the suggested checks. If this does not resolve the problem, please contact your
Specifi cations
Specifi cations
• These specifi cations are subject to change without notice.
cm (0.7 type)
TFT active matrix
432
pixels (
horizont
ve
Zoom le
29.
Zoom le
230
W UHB
W x 1
AC100-120V
/
4
A, AC220-240V/
2
A
W
Temperature range
(W) x
(H) x
2
(D) mm
Weight (mass)
kg
kg
Air fi lter
..
..
D-sub 15pin mini x1
Audio input:
AUDIO 1
AUDIO 2
Audio output
AUDIO OUT
...
Video input:
(Y,
/P
/P
......
................................
Video
49
Specifi cations
Loading...