Toto SW84312 Installation Manual
Water drainage
plug
Release button
for removing the
main unit
Lid
Label
Heated toilet seat
Wand
Base plate
Remote controller
Power plug
Connection hose
Toilet seat sensor
Main unit
Junction valve
Remote controller Remote controller
wall hanger
Anchor bolts (3)
Screws (3) Remote controller batteries
(2 AA batteries)
Bolts (2)
Washers (round, 2)
Washers (lock, 2)
Stopper (2)
Rubber bushing (2)
Base Plate
Template
2004.9.27 D06694S
Washlet E200 Installation Instructions
Before installing your Washlet, be sure to read the following installation instructions and install the product only as described in this manual.
Prohibited
Use of This
Product:
Safety Precautions
The symbol indicates a prohibited use of the product.
Do not install the Washlet in a wet or damp
place, such as a shower stall or bathtub
area. Doing so may cause fire or electrical
shock.
Only use tap water or drinkable well water
(ground water).Use of water that is not safe
for drinking may cause irritation or injury to
the skin.
Do not remove the
drain valve and water
filter with the water
shutoff valve in the
OPEN position.
After cleaning the water
filter, be sure to insert it
into the drain valve and
securely tighten the drain
valve to avoid water leakage.
This product should be used with grounded
120V, 60Hz electrical current only to avoid
possible fire or shock.
Do not use a loose or faulty electrical outlet
or plug.Doing so may cause fire or electrical
shock.
This symbol means "Always follow this precaution".
DANGER
WARNING
Do not bend or crush the
connection hose.Bending
or crushing the connection hose may result in
water leakage.
Follow all safety precautions and warnings when
installing the Washlet.
Make sure that a ground wire has been
installed. Failure to install a ground wire
could result in electrical shock in the event of
a malfunction or short circuit.
Be sure to plug the electrical cord all the way
into the wall socket to avoid possible fire or
electrical shock.
Do not raise the toilet seat or
seat cover while objects are
resting on top of the toilet, as
this could cause the main unit
to become detached, resulting
Do not install base
plate to Washlet
when not attached
to the toilet. Fire or
damage may result.
in injury.
Before Installing the Washlet
1. Do not transmit electrical current or supply water to the unit until
the installation process is complete.
2. The power voltage is 120V/60Hz. The rated energy consumption
is 410 W. Use wiring and electrical outlet appropriate for this level
of power.
3. The power cord is 3 feet (1m) in length. The electrical outlet
should be installed on the wall to allow easy installation and
removal of the Washlet .
4. Use a water supply of 20 - 80 PSI (0.14Mpa ~ 0.55Mpa).
5. The water temperature range should be 0 ~ 35°C (32~95°F).
6.
The length of the connection hose is 1.5 feet (500mm). The water
supply should be installed to allow easy installation and removal of
the Washlet.
Parts IdentificationParts and Features
¶ Washlet Main Unit Ë Remote Controller Parts
Ì Base Plate Parts
Ï Instruction Manual
Warranty Card
Installation Instructions
Í Connection Hose
Î Junction valve
(with packing washer)
Use second set of mounting holes for
decoratively curved toilets.
Ð Washers (2) ½
Optional Elbow Joint
Installing the Washlet
Tank's Water Inlet
Container
Flexible Tubing
Junction
Valv e
Flexible Tubing
Packing Washer
Adjustable
Wrenches(2)
Phillips and
flathead
Screwdriver
Packing
Washer
Junction
Va
lve
Bolt
Bolt (with washer)
Washer (round)
Lock Washer *
Stopper
Rubber bushing
Rubber bushing
Base plate
Paper template
Holes for insertig
the toilet seat
Assemble the paper template.
The assembly instructions are
written on the template.
Insert the rubber bushings into the holes on the
toilet bowl (in both the right and left holes).
Wet the tip of the bushings to
make insertion easier.
The lock washer
should be assembled
"face up".
Two small dents
indicate the "up"side.
2 small
dents
*Lock Washer
How to Install the Base Plate
Center of the bolt
Base plate
Measure this length
Toilet bowl
Measure the distance from the center of the
bolt to the tip of the toilet bowl.
If this distance is
18.5 in
(47 cm)
16.5 in
(42 cm)
then the toilet bowl
is Elongated.
then the toilet bowl
is round.
(3-A) (3-B)
Low Tank
of the paper
template
edge
Back
[Bolt and "Round" text line up]
➀ Match up the center of the bolt with the position
marked "round" on the paper template.
Bolt
Black Line
Toilet bowl
Round
[Bolt - elongated - mach up]
Bolt
Elongated
Paper template
Low tank
Base plate
Black line
Proceed to step 4.
A small space
may be left
between the
tank and the
base plate.
Paper template
The black line is
slightly in front of
the toilet bowl edge
The black line
lines up with the
toilet bowl edge
Black line
Toilet bowl edge
There is
a space
Bolt
Move the base plate
to adjust its position.
ELONGATED
ROUND
Bolt
Connecting the Junction valve
1
The instructions and illustrations for this section are for common toilets found in
most homes. Your toilet may vary in appearance. If you cannot find a described
fixture or connection on your toilet, you may have a custom toilet installation that
requires professional installation for the Washlet.
2
Remove the flexible tubing (or metal /
copper tubing) from the tank’s water inlet
using an adjustable wrench. Drain the
water from the flexible tubing into a
container.
Tools you will need:
Caution
l If you are not familiar with plumbing
and installing plumbing fixtures, you
may need to hire a contractor to do
this installation.
l Improper tightening of a connection,
either under-tightening or over-tighten
ing can result in water leakage.
1
Close the water supply shut-off valve near the wall.
Flush the toilet to empty the water tank, and place a container under
the tank’s water inlet. If water flows into the toilet or water tank, check
the water supply shut-off valve to make sure it is completely closed.
Failure to completely close this valve may result in flooding when the
flexible tubing is disconnected in the next step.
Turn the water supply
shut-off valve clockwise
Notes
l If your tank is connected to the water supply shut-off valve with metal
or copper tubing, you must replace it with flexible tubing.
l Check the condition of the flexible tubing. If it is cracked, worn or
damaged, replace it before continuing this procedure.
-
3
Place the packing washer inside the nut on
the junction valve, and install the junction
valve onto the tank’s water inlet using an
adjustable wrench.
Make sure the washer is seated properly on
the junciton valve.
4
Install the flexible tubing onto the junction valve.
You may need to replace the packing washer on the flexible tubing if it is
worn or damaged.
Notes
If you have removed the metal or
copper supply tubing in step 2, you
must replace it with flexible tubing.
Caution
l Do not overtighten the nuts.
Overtightening can damage the
connection and cause leaks. Use
moderate pressure to tighten the
nuts.
l When tightening the junction valve,
make sure that the hose does not
become bent. If the hose should
become bent, the water supply may
not be able to reach the W
ashlet.
Attaching the Washlet to the Toilet Bowl
2
Installation on a curved toilet is slightly different. Please refer to page 3.
Attaching to an ordinary toilet bowl.
1
Install Base Plate
Installation Template is attached to the Base Plate. Do not remove.
2
Confirm the size of the toilet
bowl.
3
Determine the correct
position for the base plate.
For a elongated toilet bowl:
3A
match up the center of the bolt
with the position marked "elongated" on
the paper template. [bolt-elongatedmatch up].
For a Round toilet bowl:
3B
Á Confirm the conditions for and .
: There should be a small space
A
between the low tank and the back
edge of the paper template.
There is a space (it should be 2mm
or more)
There is no space
: The black line on the paper template
B
should be lined up with or slightly in
front of the edge of the toilet bowl.
A B
 If and are both m: proceed to step 4.
If either or is X, adjust the position of
the base plate, as shown in the diagram to
the right, so that both and are m.
After adjusting the position of the base
plate, proceed to step 4.
A B
A B
A B
4
Temporarily tighten
Insert Rubber Bushing into seat mounting hole in
toilet bowl. Tighten bolt to secure plate to bowl.
Tip: Wetting the Rubber Bushing will make
installation into the toilet easier.
Loading...