Toto MS626124CEFG01 Installation Manual
Installation Manual
Manual de Instrucciones
Manuel D’Installation
MS614114CEF(G)
MS614114CUF(G)
MS624124CEF(G)
MS624234CEF(G)
MS626124CEF (G)
MS626234CEF (G)
MS644114CEF(G)
MS874114S(G)
MS884114
MS904114
MS934214(E)(S)F
MS934304(E)(S)F
MS964214C(E)F(G)
MS974224C(E)F(G)
MS984244CF(G)
Warranty Registration and Inquiry
For product warranty registration, TOTO U.S.A. Inc. recommends online warranty registration. Please visit
our web site http://www.totousa.com. If you have questions regarding warranty policy or coverage, please contact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260
(888) 295-8134 or (678) 466-1300 when calling from outside of U.S.A.
TABLE OF CONTENTS
Thanks for Choosing TOTO
Before Installation ...............................................................................................................2
Common Tools Needed ....................................................................................................2
Included Parts ..................................................................................................................... 2
Before Installation ...............................................................................................................3
ENGLISH
Installation Procedure ........................................................................................................3
Maintenance Instructions ...................................................................................................5
Care and Cleaning ..............................................................................................................8
Warranty ..............................................................................................................................9
Rough-In Dimensions ...................................................................................................... 26
Replacement Parts ...........................................................................................................27
®
! ...........................................................................................2
THANKS FOR CHOOSING TOTO!
The mission of TOTO is to provide the world with healthy, hygienic and more
comfortable lifestyles. We design every product with the balance of form and function
as a guiding principle. Congratulations on your choice.
COMMON TOOLS NEEDED
• 12” pipe wrench
• 10” adjustable wrench
• Carpenter’s Level
• Tape Measure
• Plier
MATERIALS REQUIRED:
• Flexible Supply Tube / Connector
• Supply Stop Valve
• Mounting (T) Bolts & Nuts (2pc)
• Wax Ring / Seal
• Screwdriver
• Putty Knife
• Drill
64
• 11/
• 5/16” drill bit for concrete/tile installation
INCLUDED PARTS
Check to make sure you have all these parts from the package:
Cover Plate
China Bowl with Lid
In the Uni Fit Rough-In box:
PVC outlet Connection
Anchor
(4 pieces)
Toilet Seat Set
Toilet Mounting Bolt (T-Bolt)
(2 pieces)
Mounting Screw with Washer
(4 pieces)
2
(2 pieces)
Top Bolt Mount Set
(for seat)
T-Bolt Washer
(2 pieces)
T-Bolt Nut
(2 pieces)
BEFORE INSTALLATION
Read these instructions thoroughly before beginning work.
Please leave instructions for customers. These instruction contain maintenance
and warranty information.
If necessary, remove the existing toilet.
IMPORTANT!
Due to the powerful performance of our Cyclone, G-Max, E-Max and Power Gravity
means of installing these toilets in a back-to-back situation is when the toilet drain
to this installation.
ENGLISH
Double Combination WYE / 1/8 Bend
YES
Double Sanitary Tee / Sanitary Cross
NO
In order for your new TOTO toilet to fit correctly, check the dimensions below:
1) The distance between
Finished Wall
the finished wall to
the center of the toilet
outlet, rough-in "RI":
Supply
Valve
"RI"
C/L
Closet
Flange
Please make sure that you have the correct outlet connection part:
“RI” Outlet Connection Part No.
TSU01W.12R / TSU03W.12R / TSU06W.12
12”
(Supplied)
9"
TSU01W.10R / TSU03W.10R
10”
(Optional - Must be purchased separately)
7
"
TSU01W.14R / TSU03W.14R
14”
(Optional - Must be purchased separately)
11"
2) The water supply must be approximately 8 inches or 10 inches to the left (facing the
INSTALLATION PROCEDURE
1) Clean any debris out of the closet
(see Illustration 1). The bolt should
be inserted into the slot with its
head down and threaded shank
pointed upward.
Ill. 1
3
INSTALLATION PROCEDURE
2)
the location shown in the Unifit RoughIn installation instructions found in
the Rough-In box (see Illustration 2).
ENGLISH
anchors).
3) Turn the PVC outlet connection upside
down. Firmly press a new wax seal
onto the circular recess around the
outlet opening. Turn the outlet connection upright and lower it into position
properly aligned, press down firmly to
set the wax seal (see Illustration 3).
CA UTION: Do not move the outlet
connection after the wax seal is set.
4) Insert the washers and thread nuts
onto the mounting bolts and handtighten (see Illustration 4). Then tighten
bolts an additional ½ turn. Secure the
back side of the outlet connection to
ers.Insert the T-bolts into the slots with
the head down and threaded shank
pointed upward.
NO TE: Level the PVC outlet. Do not
use excessive force.
5) Lift the toilet and gently lower it into
lustration 5). Make sure that the spigot
outlet of toilet slips into the rubber
sleeve and that the T-bolts fit through
the openings in the base of toilet.
Insert the washer and thread nuts
onto the bolts and hand tighten. Then
tighten the bolts an additional ½ turn.
Install the cover plates.
WA RNING! Do not over-tighten the
nuts. Damage to china or plastic
parts may result.
Ill. 2
Ill. 3
Ill. 4
T-Bolts
-
-
Ill. 5
Nut
Washer
Cover
Plate
Slot
2"
Finished Wall
B
A
Rubber
Sleeve
Spigot
Outlet
Floor
C/L
C
Closet Flange
Wax Seal
Nut
Bolt
4
INSTALLATION PROCEDURE
6) The supply stop should be installed per
the supply stop instruction at the location
shown in the Before Installation section.
hose to supply stop.
CAUTION: Hand-tighten only.
Open the supply stop, checking for leak-
age. Slightly re-tighten if necessary. The
water supply pressure should be 20 to 80
psi static.
7) NOTE:
are needed. The water will automatically
stop at proper level.
per valve for proper operation. Make sure
in its proper position.
8) Install the toilet tank lid onto the toilet tank
top.
9) Install the toilet seat onto the toilet bowl
(see Illustration 7). (Top Mount Bolt Set is
included with the bowl). Insert the rubber
bushing nuts into the bowl seat holes.
NO TE: Remove the existing seat if neces-
sary.
Place the seat on the bowl and rotate the
hinge unit into place while holding seat
down on the bowl. Fasten and tighten
the bolt from the top with a screwdriver.
Replace the bolt cap and the lower lid (if
necessary).
-
Ill. 6
Trim Plate
Ill. 7
Water
Inlet
Washer
Coupling
Nut
Nipple
Seat Bolt
Flexible
Supply
Hose (not
supplied)
Valve
Nut
Compression
Valve
Rubber
Brushing
Nut
ENGLISH
MAINTENANCE INSTRUCTIONS
Fill Valve Replacement Procedure
1) Shut off the water supply to the toilet.
2) Flush toilet and remove remaining water from tank with a sponge.
NO position that does not
interfere with the trip lever operation.
5
MAINTENANCE INSTRUCTIONS
Fill Valve Replacement Procedure (continued)
.
NO TE: Do not overtighten. These are plastic parts. Never use pipe dope on any
ENGLISH
water supply connection.
8)
pipe.
9) Turn water supply ON and check for leaks outside the tank.
NO TE:
e
w
Once the water stops filling the tank, some residual drops of water may drip
drops will subside.
Water Level Adjustment
Depending on the manufacturing plant, you may have one of two of the following fill
valves:
Type A Type B
Type C
Water Level
For Type A Fill Valve:
Refer to the water level (WL) setting marked
on the inner wall of the tank. Allow the wa-
clockwise in the (+) direction to increase the
water level height (see Illustration 1). Turn
the adjustment screw counter-clockwise in
the (-) direction to decrease the water level
height. Flush the toilet to verify the correct
water level. Adjust as necessary.
For Type B Fill Valve:
There are no water level adjustments. The
fill valve has been preset at the factory.
6
Ill. 1
Water
Level
Top of
Tube
MAINTENANCE INSTRUCTIONS
Replacing the Flush Valve (CST614CUFG Model Only)
1) Turn off water supply and ush the toilet.
Remove the remaining water from tank
with a sponge.
2) Remove the tank lid and place it upside
down on a clean surface.
3) Pull the clip on top of trip lever gear box as
shown. (see Ill.1)
4) Pull gear box away and set on the side as
shown. (see Ill. 2).
5) Rotate and pull up on the ush tower to
remove it. (see Ill. 3).
6) Remove the grey rubber seal gasket and
rinse under running water to clean.
(see Ill. 4).
7) Place the gasket back on the ush tower.
8) Align and place the ush tower into housing and gently press to snap and to lock
into place.
9) Replace the trip lever gear box and push
down on lever to lock it in place.
10) Carefully install the tank lid back on the
tank.
11) Flush the toilet several times making sure
the trip lever operates normally.
12) Check the water level in the tank and leak.
ENGLISH
*Actual product may vary from
illustration
Ill. 1
Ill. 2 Ill. 3
Ill. 4
Ill. 4
7
MAINTENANCE INSTRUCTIONS
Replacing the Drain Valve
1) Shut off the water supply.
2) Flush the toilet to remove the water
inside the tank.
ENGLISH
3) Remove the tank lid and place
somewhere safe.
NOTE: Before removing anything
from the tank, note the placement
of the drain valve, chain and refill
tube.
4)
5)
turning counter-clockwise with the
chain hook still attached to the trip
lever (ill.1).
6) Unhook the chain from the trip
unit (ill. 2).
7) Unscrew the three screws from the
drain valve body.
IMPORTANT: Make sure not to turn
more than seven full turns as the
black mounting block can fall into
the water channel.
8) Remove the drain valve body from
the tank (ill. 3).
9) Replace the drain valve in the same
position as the former drain valve.
10) Tighten the screws, applying light
torque on each screw before final
torque on all three screws.
11)
drain valve body and turn clockwise
to lock the part.
12) Hook the chain back to its original
loction, and the refill tube.
13) Turn the water supply back on and
check for any leak after the tank has
been filled.
ill. 1
ill. 2
ill. 3
Flush Tower
Refill Tube
Overflow
Tube
Drain Valve
Drain Valve
Body
CARE AND CLEANING
WARNING!
DO NOT USE IN-TANK BOWLCLEANERS.
The use of high concentration of chlorine or chlorine-related products can seriously
damage fittings in the tank. This damage can cause leakage and property damage.
®
TOTO
shall not be responsible or liable for any tank fitting failure or damage caused
by the use of in-tank bowl cleaners.
8
WARRANTY
1. TOTO warrants its vitreous china products (“Product”) to be free from defects in materials
and workmanship during normal use when properly installed and serviced, for a period of one
(1) year from date of purchase. This limited warranty is extended only to the ORIGINAL PURCHASER of the Product and is not transferable to any third party, including but not limited to
any subsequent purchaser or owner of the Product. This warranty applies only to TOTO Product
purchased and installed in North, Central and South America.
2. TOTO’s obligations under this warranty are limited to repair, replacement or other appropriate adjustment, at TOTO’s option, of the Product or parts found to be defective in normal
use, provided that such Product was properly installed, used and serviced in accordance with
instructions. TOTO reserves the right to make such inspections as may be necessary in order to
determine the cause of the defect. TOTO will not charge for labor or parts in connection with
warranty repairs or replacements. TOTO is not responsible for the cost of removal, return and/
or reinstallation of the Product.
3. This warranty does not apply to the following items:
a.
b. Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negli-
c. Damage or loss resulting from sediments or foreign matter contained in a water system.
d. Damage or loss resulting from improper installation or from installation of the Product in
e. Damage or loss resulting from electrical surges or lightning strikes or other acts which are
f. Damage or loss resulting from normal and customary wear and tear, such as gloss reduc-
g.
h. Toilet seats of plastic, wood or metal.
4. In order for this limited warranty to be valid, proof of purchase is required. TOTO encourages
5. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS
6. To obtain warranty repair service under this warranty, you must take the Product or deliver it
WARNING! TOTO shall not be responsible or liable for any failure of, or damage to, this Product caused by either chloramines in the treatment of public water supply or cleaners containing
chlorine (calcium hypochlorite). NOTE: The use of a high concentrate chlorine or chlorine related
products can seriously damage the fittings. This damage can cause leakage and serious property
damage.
THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO. REPAIR, REPLACEMENT
OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE
THE EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. TOTO SHALL NOT BE
RESPONSIBLE FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR
LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY
OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY
WILL TOTO’S RESPONSIBILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. EXCEPT TO
THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT
OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR PURPOSE, ARE EXPRESSLY DISCLAIMED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.
electrical storm, etc.
gence, or improper care, cleaning, or maintenance of the Product.
Product. (NOTE: Product model codes allow a maximum of 80 PSI. Check local codes or
standards for requirements).
not the fault of TOTO or which the Product is not specified to tolerate.
tion, scratching or fading over time due to use, cleaning practices or water or atmospheric
conditions.
warranty registration upon purchase to create a record of Product ownership at http://www.
totousa.com. Product registration is completely voluntary and failure to register will not diminish your limited warranty rights.
WHICH VARY FROM STATE TO STATE, PROVINCE TO PROVINCE OR COUNTRY TO COUNTRY.
prepaid to a TOTO service facility together with proof of purchase (original sales receipt) and a
letter stating the problem, or contact a TOTO distributor or products service contractor, or write
directly to TOTO U.S.A., INC., 1155 Southern Road, Morrow, GA 30260 (678) 466-1300 or (888)
295-8134, if outside the U.S.A. If, because of the size of the Product or nature of the defect, the
Product cannot be returned to TOTO, receipt by TOTO of written notice of the defect together
with proof of purchase (original sales receipt) shall constitute delivery. In such case, TOTO may
choose to repair the Product at the purchaser’s location or pay to transport the Product to a
service facility.
STATED ABOVE. IN NO EVENT
ENGLISH
9
Loading...