Toto RYOHAN TEL3GMY, Helix TEL3GW*CP Installation Manual
INSTALLATION MANUAL
AUTOMATIC FAUCET
Single supply faucet
Important Safeguards
(For your safety, please follow the instructions below.)
In this Instruction Manual, the following symbols are shown for safe and proper use
of your automatic faucet and in order to alert you to the possibility of personal injury
and damage to your property.
The symbols and their meanings are as follows.
Warning
Ignoring these symbols may cause
personal injury and/or property damage.
*Some models may have different components from the ones illustrated below.
Do not place the
Automatic Faucet
in a high humidity
area such as shower room or sauna.
This may cause damage.
Do not use in
humid area
Warning
Do not strike or kick the Automatic Faucet.
This may cause damage or water leakage.
Never attempt to disassemble, reassemble,
repair
or modify the Automatic Faucet
, unless you are an
electrician, or qualified service person.
This may cause property damage or personal injury.
Do not
disassemble
Do not strike
Specification
EcoPower
type
Model
number
Power supply
-
-
Battery life
Item
Detection range
from the sensor
5-1/8"~7-7/8" (130~200 mm)
sensor is self-adjusting
Water supply
pressure
minimum required water pressure:
14.5 PSI (100 kPa) ( Flowing)
maximum water pressure:
125 PSI (862 kPa)
check local building codes for maximum water
pressure allowed
Water supply connection
1/2" NPSM
RYOHAN™
TEL3GMY
Ambient temperature
32~104oF(0~40oC)
Humidity
Max. 90% RH
Flow rate
0.8 gallon per minutes (3 L/min.)
Duration of
water discharge
Discharge quantity
Max. 0.25 gallon per cycle (0.95 L/cycle)
60 seconds (TEL3 - 60)
Helix™ Wall mount
TEL3GW#CP
0GU3013ER
2007.03
10-1/4”
(260mm)
1-1/4”
(159mm)
1-1/8”
(30mm)
8-5/8”
(218mm)
6”
(152mm)
Water
Supply
Single Supply
Controller
2-3/8”
(60mm)
60
7-5/16”
(186 mm)
2” (50 mm) to
5” (127 mm)
~ 33”
(838 mm)
overall
length
Ø4x40
3 screws
with anchors
1-3/4”(45mm)
Faucet
6-5/8”
(168mm)
8-1/8”
(207mm)
2-3/4”
(70mm)
10-1/4”
(260mm)
1-1/4”
(159mm)
1-1/8”
(30mm)
8-5/8”
(218mm)
6”
(152mm)
Water
Supply
Single Supply
Controller
8
Please confirm the basin dimension of lavatory, to
which the faucet will be installed, making sure that it
has recommended minimum dimensions of
(L x W: 15" x 15").
Faucet Hole Diameter
Min. 28mm (~1-1/16”)
to
Max. 35mm (~1-3/8”)
Before Installing
1.
Check the pressure of cold and hot water supply
2. Piping
3. Others
When the water supply pressure is higher than 125PSI (862kPa), be sure to
reduce the pressure within a range of 20 to 80 PSI by using a pressure
reducing valve available in the market.
Optimum working pressure range is from 14.5PSI to 125PSI (100kPa to
862kPa). Make sure the water pressure is within this range.
Flush all water lines prior to installation.
Pay special attention so that the sensor surface is not flawed or scratched.
Prepare stop valve and flexible hose or copper tube.
Do not place other devices using inverter or infrared sensor near the
Automatic Faucet, this may cause malfunction.
There is no problem with the Automatic Faucet if water remains inside.
Set-up Drawing
Some models may have different components as illustrated below.
Battery type
Ryohan™
Battery type
Helix™ Wall Mount
Installation
*Some models may have different component as illustrated below.
Control box Water inlet bracket
Water inlet bracket
Self tapping screw (×3)
(φ4.5 mm×38)
Quick fastener
Drain Drain Pipe
Installation
manual
Instruction
manual
Others
Allen wrench
Size:1/16"(2mm)
*Spout , Flexible tube and Open-close tool are included.
RYOHAN™ Spout Flexible tube
Open-close tool
Others
Flexible tube is installed
through spout connecting
hose.
EcoPower® type
¤
RYOHAN™
Screw
(φ3 mm×10)
Helix™ Wall Mount Spout Flexible tube
Open-close tool
Others
Flexible tube is installed
through spout connecting
hose.
¤
Helix™ Wall Mount
3 Phillip Screws
(
Ø4x40 )
3 screw anchors
Loading...